Search Documents

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By B. k. Kenzhaliyev, M. A. Naimanbayev, Zh. A. Baltabekova, N. G. Lokhova

In research various desorbents were used to desorb the following rare-earth metals from Purosorb 140 cation exchanger, i.e. ammonium chloride; ammonium sulfate; a mixture of nitric acid and ammonium nitrate; a mixture of hydrochloric acid and ammonium chloride; a mixture of sulfuric acid and ammonium sulfate. It was established that a solution containing 30 g/dm3 of H2SO4 + 300 g/dm3 of (NH4) 2SO4 is the most optimal desorbing solution to desorb REMs from macroporous Purosorb 140 cation exchanger impregnated with rare-earth metals from industrial dihydrate wet-process phosphoric acid. It was established that the residual REM content in the cation exchanger decreased from 0.89 to 0.10 wt. % with an increase in the ammonium sulfate concentration from 10 to 400 g/dm3. Technological desorption regimes for rare-earth metals from cation exchanger were developed. The optimal conditions were determined to desorb rare-earth metals from the Purosorb 140 cation exchanger, particularly temperature 25°C; L:S ratio = (0.8 ÷ 1.1):1; duration = 1.0-1.5 hours. Keywords: Rare elements, sorption, cation exchangers, wet-process phosphoric acid, desorption

Jan 1, 2020

By P. J. Petit

"The complex planning required to achieve any planned production yields multiple and dissociated responses over the life of project (LOP). The customary decision-making process negates the possibilities of developing optimized and integral solutions from operating levels up to business and strategic levels. This results in an inefficient project or overall underperformance of the operation.In the project setting, disconnected trade-offs and improved performance studies become inadequate, because they are site-specific and use only a few comparative parameters. They are often based on a small data-set.Decisions taken to achieve overall objectives require the correct determination and dissemination of key performance indicators (KPIs). The KPIs indicate efficiency in operation, whereby the marginal rate of technical substitution corresponds to the rate of production. It is the necessary condition for optimization. Performance realization for sustainability follows optimization modelling, the latter often being presented with financial results such as business net present value (NPV). It considers techno-financial constraints and provides a strategic and aligned outlook of KPI decisions for an enhanced and integrated outcome.This paper explains a mining case study that is rendered efficient, and through business optimization (BO) short-term and sustainable targets are reached. Business optimization increases the NPV by 14.7%. This is achieved by challenging conventional decision-making associated with maximizing business value by including environmental externalities within the LOP."

Jan 1, 2016

By J. P. Harrison, J. A. Hudson.

ABSTRACT: When considering the rock stress component of rock mechanics design, the basic procedure is to consider the pre-existing stress-state in the rock mass and then estimate the disturbance to this stress state as a result of engineering excavation. Failure criteria are applied to the final stress state to establish whether failure will occur. However, during the evolution of the stress state, the failure locus may be reached before the anticipated failure state and, in this case, failure will occur unexpectedly. This indicates that the complete stress path (defined as the variations in magnitudes and orientations of the stress tensor components resulting from engineering-induced or natural changes) must be considered. We list a set of stress path principles with their corollaries and then introduce a new and powerful method for simultaneously illustrating changes in the six independent components of the stress tensor. This method plots the magnitudes of the principal stresses above their orientational paths on the hemispherical projection, to provide a three-dimensional stress path locus for each of the three principal stress components. In connection with this presentational device, we illustrate a number of concepts associated with the stress path in rock engineering. For example, we show how the minor principal stress approaches zero at an unsupported excavation face, the interchange of the trajectories of two principal stresses when their magnitudes become equal, and the influence of the bounds on the principal stresses given by strength criteria. RESUME: Si on s’interesse à la composante “contrainte” lors d’un dimensionnement en mécanique des roches, la méthode de base consiste à considérer l’état de contrainte pré-existant dans le massif rocheux, puis d’estimer la perturbation à cet état générée par l’excavation projetée. Des critères de rupture sont appliqués à l’état de contrainte final pour établir si une rupture va se produire. Cependant, lors de l’évolution de l’état de contrainte, la surface critique peut être atteinte ce qui provoquera une rupture anticipée et, dans ce cas, cette dernière sera inattendue. Cela indique que le chemin de contrainte complet (défini par les variations de l’intensité et de l’orientation des composantes du tenseur des contraintes liées à des causes anthropiques ou naturelles) doit être pris en compte. Nous présentons un ensemble de règles pour les chemins de contraintes ainsi que leurs corollaires et, ensuite, nous introduisons une méthode, nouvelle et puissante, pour présenter simultannement les changements des six composantes du tenseur des contraintes. Cette méthode consiste à tracer l’intensité des contraintes principales sur le chemin d’orientation des contraintes à l’aide d’une projection hémisphérique afin d’obtenir le lieu, en trois dimensions, de chaque contrainte principale. En relation avec cet outil de représentation, nous illustrons certains concepts associés au chemin de contrainte en ingénierie au rocher. Par exemple, nous montrons comment la contrainte mineure tend vers zero à la surface d’une excavation sans soutenement, le changement de direction des deux contraintes principales quand leur intensité deviennent égales, et l’influence des conditions aux limites sur les contraintes fournies par un critère de rupture. ZUSAMMENFASSUNG: Bei ingenieurmassigen Taetigkeiten in Felsgesteinen ist es noetig die ungestoerten Gesteins Stress Componenten, die vor einem anthropogen Eingriff im Gestein vorhanden waren, zu kennen und erst dann Vorhersagen ueber Stoerung des Stress Zustandes, der durch einen ingenieurmaessigen Eingriff hervorgerufen wird, herzuleiten. Kriterien fuer das Versagen werden im letzten Stadium, des Stress Zustandes angewendet, um zu erfahren ob ein Versagen wohl eintreten wird. Es ist jedoch zu beachten, dass waehrend des Stress Aufbaus ein oertliches Versagen eintreten kann, welches vor dem eigentlichen, erwarteten Versagens Zustand auftritt. Diese Moeglichkeit weist darauf hin, dass der gesammte “Stress Path” (definiert durch die Variationen der Stress Tensor Komponenten in Richtung und Groesse, hervorgerufen durch ingenieurmaessig hervorgerufene oder natuerlich Vorgaenge) betrachtet werden muss. Wir fuehren eine Liste der “Stress Path” Prinzipien auf und stellen dann eine neue und wirksame Methode zur gleichzeitigen Darstellung der sechs unabhaegigen Komponenten des Stress Tensors vor. Diese Methode stellt die Groesse der “Principal Stresses” in Abhaengigkeit von ihrem rauemlichen Weg auf einer hemispherischen Projektion dar und erlaubt hiermit eine drei dimensionale Darstellung fuer jeden Ort des “Stress Path’s” in die drei Haupt Stress Komponenten. Im Zusammenhang mit der hier gegebenen Darstellungsart, verdeutlichen wir eine Reihe von Konzepten in der Felsmechanik. Wir zeigen zum Beispiel, wie der “Minor Principal Stress” Null zustrebt an einer Wand von einer nicht abgestuetzten Ausschachtung, den Austausch von Trajektorien zweier “Principal Stresses” wenn ihre Groessen sich gleichen, und den Einfluss der Groesse von “Principal Stresses” bei gegebenen Kriterien des Festgkeits Versagens.

Jan 1, 2003

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024

The following is available free of charge from the Bismuth Institute, rue Brederode 9, B-I000 Brussels, Belgium: The chemical analysis of bismuth. Automatic methods of guiding welding heads along butt joints. Investigations into lamellar tearing. A technical survey of seam tracking methods in welding. Review - Seawater corrosion handbook, by M. Schumacher (editor). New Jersey, Noyes Data Corporation, 1979. New journal February 1979 marked the appearance of a new monthly journal, Lloyd's Shipping Economist. New edition Gasification of coal, a basic study of existing processes and new developments, by H. D. Schilling, B. Bonn, and U. Krauss (edited by W. Peters). Essen (West Germany), Verlag Gltickauf GMBH, 1979. 2nd revised edition. 336 pp. 68DM (approximately R32). In German. South African technikons The six autonomous colleges for advanced technical education in South Africa were established in terms of the Advanced Technical Education Act (Act 40 of 1967). However, since the inception of these colleges, it has become clear that members of the public find the name difficult to use and to remember. Consequently, these colleges, which play such an important role in the community, were not always correctly identified. Die forging The 9th International Conference on Die Forging will be held from Monday, 4th to Saturday 9th May, 1981, in Diisseldorf, Federal Republic of Germany. It is being organized jointly by the Forging Committee of the Verein Deutscher Eisenhiittenleute and the Vereinigung Deutscher Freiformschmieden. High-temperature alloys An International Conference on the Behaviour of High Temperature Alloys in Aggressive Environments will be held in Petten (North-Holland) from 15th to 18th October, 1979. Strategic minerals The National symposium on the availability of strategic minerals, which is being organized by the Institution of Mining and Metallurgy in collaboration with the Fellowship of Engineering, will be held at the London Press Centre, New Street Square, London EC4, on 20th and 21st November, 1979. The symposium has as its main objective consideration of those minerals that may pose problems of availability in the United Kingdom. Underwater mining The 10th Annual Underwater Mining Institute is scheduled for 1st to 3rd October, 1979, at Galveston, Texas. The Institute will be cosponsored by the Sea Grant College Programs of the University of Wisconsin and Texas A & M University and by the Marine Science Institute of the University of Texas it is being held in co-operation with the Association for Marine Mining. Die Suid-Afrikaanse Instituut Vir Mynbou En Metallurgie - Inligting Oor Lidmaatskap.

Jan 1, 1979

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well proven Swiss Tunnel Seismic Prediction System TSP has been substantially augmented for online geological prognosis in underground construction. In its latest version, the Integrated Seismic Imaging System ISIS provides high resolution seismic images of the rock mass around a tunnel face via an array of standard anchor rods. These rods contain 3D-geophones at their tips and can be readily installed during excavation work. A further innovative component of the system is the newly developed high-power repetitive source for application in hard rock: a pneumatic hammer with laser triggering to be mounted on construction machinery. A user-friendly software package permits online data acquisition and processing, 3D-visualization, and a first geological interpretation. Tomographic images of compressional and shear wave velocity fields at fault zones in metamorphic rock of the Gotthard Base Tunnel in the Central Alps are presented. Das langjährig bewährte Schweizer Tunnelseismische Vorauserkundungssystem TSP wurde inzwischen wesentlich weiterentwickelt. In seiner neuen Version, dem Integrierten Seismischen Imaging System ISIS, ermöglicht es hochauflösende seismische Abbildungen des Gebirges im Vorfeld und Umfeld einer Tunnelauffahrung mit Hilfe einer Anordnung von Felsankern, die an ihren Spitzen 3-Komponenten-Geophone enthalten. Eine weitere Neuerung von ISIS ist die pneumatische Hochleistungs-Impulsquelle mit Laser-Triggering. Eine benutzerfreundliche, interaktive Software ermöglicht die online Datenerfassung und -auswertung, 3D-Visualisierung und eine erste geologische Interpretation. Tomografische Abbildungen von Kompressions- und Scherwellengeschwindigkeitsfeldern an Störungszonen in metamorphem Gestein des Gotthard-Basistunnels werden gezeigt. Basé sur de nombreuses années d’expérience, le système suisse, bien établit, de reconnaissance sismique à l’avancement des tunnels (système TSP), a été sensiblement amélioré pour obtenir une prévision géologique en temps réel durant l’avancement de travaux souterrains. Sa dernière version, le Système Intégré d’Imagerie Sismique (ISIS), fournit des images sismiques haute-résolution du massif rocheux à l’avant d’un tunnel grâce à un réseau de tiges d’ancrage standard. Ces tiges, équipées à leur extrémité de géophones 3 composantes, s’installent très aisément durant les travaux d’excavation habituels. Le élément d’innovation récente concern le nouvelle source très répétitive et de forte puissance pour les applications aux roches dures: un marteau pneumatique déclenché par un système à laser. Un ensemble de programmes informatiques convivial permet l’acquisition et le traitement en temps réel des signaux et produit une vue 3D ainsi qu’une première interprétation géologique. Nous présenterons des images de réflexion d’ondes de compression et de cisaillement ainsi que des inversions tomographiques de zones de faille dans des terrains métamorphiques obtenues à l’occasion du creusement du tunnel de base du Gothard, dans les alpes centrales.

Jan 1, 2003

By D. F. Malan, J. A. L. Napier

This paper describes some important aspects associated with historical underground measurements in South African gold and coal mines. Deformation measurements were used to confirm the use of elastic theory to simulate the rock mass behaviour in the Witwatersrand gold mines in the 1960s. Although a prominent time-dependent component of stope closure was measured as early as the 1930s, it was ignored owing to the benefit of adopting elastic theory. Neglecting the time-dependent response of the rock for many decades resulted in important aspects such as the effect of mining rate, the effect of advance per blast, and the need for enhanced design criteria not being explored. Recent work is only now starting to address this gap in knowledge. In-situ measurements of large coal specimens in the 1960s and 1970s indicated that a linear formula may possibly be a better approximation of coal pillar strengths. This alternative formulation was never adopted, however, as the power law strength formula was already deeply entrenched in the industry at that stage. In spite of these apparent failures to continuously generate and adopt new knowledge, a key lesson learnt is that major advances in rock mechanics will not be possible without careful monitoring of the rock mass behaviour in experimental sites. Areas requiring further research, such as pillar strength formulae for the Bushveld Complex and enhanced design criteria for the gold mines, can only be developed using extensive undergroundmonitoring programmes.

May 1, 2021

By K. E. H. K. Ishak, S. R. M. Zan

Cement production requires significant energy, and entails high costs and CO2 emissions. This is because the clinker requires very fine grinding. Grinding aids can improve production and fineness and decrease energy consumption by reducing the agglomeration of particles and protecting the balls and liners in the mill. In this study we compare the effects of three different grinding aids on clinker grinding using a ball mill. A commercial grinding additive, triethanolamine (TEA), and two industrial grinding aids (GAA079 and GAA088) were compared by ball milling tests, with additions of 0.05, 0.25, 0.50 and 1.00 wt%. The industrial grinding aids were characterized using gas chromatography-mass spectrometry (GC-MS). Particle size and morphological analyses were performed using SEM and XRD. The best results were obtained with 0.25% GAA088, which has a higher active component of diethanolamine isopropanolamine (DEIPA) than TEA. The unique combination of TEA and DEIPA in GAA088 enhances grinding efficiency and significantly improves the particle size distribution compared to TEA alone.. The grinding aids produced smooth rounded particles, which have a smaller specific surface area, enhancing the quality of the cement. XRD showed no significant structural distortion with or without grinding aids, and it was also found that the grinding aids helped decrease ball coating during grinding. The use of grinding aids can significantly improve clinker production and fineness while decreasing energy consumption, which can help reduce the costs and CO2 emissions associated with cement production.

Sep 6, 2023

By C. W. P. Finn

INFACON is of special significance to people in South Africa who are interested in ferro-alloys, because it was in South Africa that the idea of regular international congresses on ferro-alloys was conceived and developed. INFACON 74, the first-ever such congress, was held in Johannesburg from 22nd to 26th April, 1974, being organized by the South African Institute of Mining and Metallurgy, the National Institute for Metallurgy, and the Ferro Alloy Producers' Association of South Africa. Design Awards The Design Institute is inviting entries for the 1981 Shell Design Awards. Any product that falls into the three categories shown below, and that was designed in South Africa and is in production, is eligible for an award. Since their inception in 1970, the Shell Design Awards

Jan 1, 1981

By D. Kok

A challenge in mine planning is the optimal allocation of resources to the appropriate workplaces within the shift cycle (labour, equipment type, and other resources) in order to carry out the shift cycle activities, achieve planned production targets, and ultimately maximize production within all infrastructure constraints. Generally, detailed mine planning is done on a monthly basis at a workplace level in order to determine the production targets. The production supervisor, mine overseer, or equivalent production manager must then make the appropriate resource allocation trade-off decisions on a daily basis per shift to try and deliver to the plan and required production target. Due to the complexity and number of permutations of possible resource allocation decisions, it is impossible for a human brain to make the appropriate and optimal allocation decisions that will result in achieving the maximum or target production. These allocation decision permutations must deal with the current status of workplaces (availability, position in the cycle etc.), the status of equipment availability (available, planned maintenance, or breakdown etc.), distance between the workplaces (traveling time of equipment between workplaces, etc.) and equipment type required for that shift cycle activity. All these factors need to be taken into account in resource allocation to plan for the shift, and even during the shift if a major piece of equipment becomes unavailable or a workplace activity is not progressing as planned. This paper is a case study on how an optimization algorithm can be used to create a production planning system for optimization of resource allocation in a mechanized underground platinum operation. A business case for optimal allocation of resources is demonstrated and compared to the current manual planned allocation.

Jan 1, 2012

By J. P. Garnier, T. Bhambhani, J. A. Garcia, N. Renaud

Most flotation plants use a static reagent scheme, i.e., a set combination of collectors, frothers, and modifiers. This scheme is usually developed and refined over time to deliver optimal (not necessarily the highest) performance when the major ore types are fed to the plant. However, when ore types or mineralogy coming to the plant change substantially (and this often happens as different areas of the pit(s) are mined and crushed at the same time), there are upsets in the process, typically leading to lower recoveries. Adapting to this variability is usually done only when performance drastically suffers, and the changes made may be too late and bring additional variability in performance. The premise for SmartFloat™ is that the reagent suite needs to be dynamic, adapting continuously to changes in the ore and operating conditions. Solvay has combined advanced analytics and data science techniques with its expertise in flotation reagent chemistry to systematically and automatically achieve the above, and in real time. Thus, SmartFloat™ is optimizing the reagent suite continuously, removing the additional variability created by belated human interactions resulting in a better and more stable process. In addition, this advanced approach allows for continuous improvement by identifying poor performing ore domains and improving the reagent suite using Solvay’s FM-100 approach to design appropriate solutions.

Jan 1, 2023

By B. Maybee, J. Venter, J. Wesseloo

The selection of open-pit slope angles involves high-value decisions with small changes in slope angle, often representing significant changes in net present value. The existing methods used to define design acceptance criteria have evolved from factor of safety to probability of failure (P[F]) to risk consequence to risk frontiers, which represents current state of the art. Current design acceptance measures are based on references to published tables representing the experience and judgement of their authors, who did not specify the purpose of the measures contained therein. As the purpose of the published design acceptance criteria is not specified (i.e., definite stability, marginal stability, optimization, etc.), such tables cannot be used to achieve optimum slope angles that maximize profitability. This paper develops a design acceptance criterion that maximizes profitability by defining a formulation for optimum risk that balances expected risk and reward. The model developed is titled the Mining Risk Model (MRM), and is applied to open-pit slope angle selection through an equation for optimum probability of downside (P[D]O) that balances the upside or opportunity, the P[F], and the downside impact. This formulation for optimum risk is unique, as many authors have presented objective functions for their risk models that can be optimized, but none of the sources reviewed contained a formulation for optimum risk. The MRM is sufficiently flexible to allow the design performance measure that drives P[F], and hence P[D]O, to be selected based on the intended goal. Furthermore, the essential information that must be known to quantify optimum risk is defined. This allows users to determine what information to collect for optimum risk decisions. A further benefit of the MRM is that slope angle decisions and pit shells can be ranked to select the best option, and a threshold is provided that separates acceptable from unacceptable decisions. Finally, the workflow and information required to determine optimum risk are presented.

Sep 9, 2024

By J. J. Cilliers, J-A. Lamamy, J. N. Rasera, K. Hadler

Production of oxygen on the moon can be achieved by reduction of lunar soil. One such reduction technology, hydrogen reduction, favours a high proportion of ilmenite in the feedstock. Ilmenite is present in lunar soil as a minor mineral phase, but it can be upgraded using electrostatic separation. This study presents the results of a preliminary investigation into the operating parameters and sensitivities of a free-fall electrostatic mineral separator for lunar applications. Samples of ballotini and ilmenite as well as simple binary mixtures of the two were tribocharged on copper and passed through a uniform electrostatic field. The field is varied to change the electrostatic force acting on the particles. The proportion of material reporting to the positive electrode collectors, negative electrode collectors or the central collector was measured to determine the separation performance. The data confirmed that the charge transferred from the tribocharger to each species is in agreement with the triboelectric series; ballotini was found to charge positively on copper and ilmenite negatively. Particle-particle contacts were dominant, however, resulting in a somewhat symmetrical particle distribution in the collectors. These findings indicate that the copper tribocharger design requires optimisation in order to substantially increase particle-wall contacts. Four binary mixtures with feed grades of ilmenite ranging from 5% to 20% were prepared and tested. This study found that a higher ilmenite head grade resulted in a higher concentrate grade (26.3% from a head grade of 20%) with low recovery (3.4%). In contrast, the lower feed grade resulted in a low concentrate grade but higher recovery. The mass yield of ilmenite was 1.4 times greater for the highest-grade feed than for the lowest. A subsequent study into the reprocessing of middling fraction found a nearly constant relationship between cumulative grade and recovery. This is the first investigation into the effect of feed grade on the concentrate grade and recovery for lunar mineral processing. Keywords: Lunar resources, beneficiation, electrostatic, SRU, ISRU

Jan 1, 2020

Brigadier R. S. G. Stokes of Sherborne, Dorset, is the oldest surviving member of the South African Institute of Mining and Metallurgy. He joined in 1904 and has been a member for 77 years. Book review Sittig, M. Hand book of catalyst manufacture. Park Ridge (U.S.A.), Noyes Data Corporation, 1978. The detailed information in this book is based on patents issued in the U.S.A. that deal with catalysts and their commercial technology. Project management The South African Institute of Mining and Metallurgy is to hold a Colloquium on Project Management in the Metallurgical Industry in March 1980. Ingenieurs-in-opleiding in die weermag Op 'n onlangse vergadering van die Suid-Afrikaanse Raad vir Professionele Ingenieurs is daar besluit om kwytskelding van jaargeld aan geregistreerde ingenieursin- opleiding wat tans met hulle tweejaar nasionale diensplig besig is, te verleen met dien verstande dat.... Engineers-in-training in the army At a recent meeting of the South African Council for Professional Engineers it was resolved that a remission of annual fees would be granted to registered engineers in- training who are doing compulsory two-year national service, provided that.... Processing of fine particles The Society of Mining Engineers of AIME is organizing an International Symposium on Fine Particles Processing, which is to be held in Las Vegas from 24th to 28th February, 1980. Economics of precious metals International Precious Metals Institute announces a Special Course for all interested in economic aspects of today's precious metals.

Jan 1, 1979

DD3-tunnels (PD BH's) ? Rotary coreholes 111no. (124) ? Percussion holes Ono. (37) ? Sampling (rock and soil) ? Soil and rock permeability ? testing ? BH Televiewer Surveys [ ]

Jan 1, 2007

By K. C. Naidoo

There are two main types of densifying cyclones currently available in the market, namely polyeurethane (PU) and ceramic. The PU densifying cyclones are currently used throughout the Grootegeluk complex and coal beneficiation in general. It has been identified that PU densifiers wear relatively fast depending on the operating pressure and need to be replaced frequently as a result. The motivation for this paper is to achieve an increase in the densifying cyclone lifetime through less wear and an increase in efficiency resulting in the ability to build higher relative densities (RD) more quickly. This will allow for a reduction in downtimes due to replacing densifying cyclones as well as building RD and a reduction in the operating costs associated with replacing worn densifying cyclones. Some of the major findings of the study indicated that the ceramic cyclone theoretically undergoes less wear than the PU cyclone, but since wear is application-specific and was evaluated, the wear on the polyurethane cyclone was found to be minimal. The RD differential is higher on the PU cyclones than the ceramic cyclones, showing that the PU cyclones perform better in a densifying application. This is the first test conducted on this application and type of cyclones. It should therefore be noted that having the PU cyclone significantly outperform the ceramic cyclone was not expected, due to the only change being the material of construction. This is an indication to take the material of construction into account when selecting cyclones as it can have a significant impact on the cyclone performance in specific applications. Keywords: Ceramic, cyclone, densifying, density, dense medium, polyurethane, wear

Jan 1, 2020

South Africa?s now a member of this body, tailored on the World Bank, and headquartered in Abidjan-Cote d'Ivoire. As a funding agency for capital projects within 59 member countries of the ADB it is to be expected that there are guidelines to the requirements for funding application and for project management and control.

Jan 1, 1996

By D. Marcotte, R. V. Dutaut

"In mineral resource evaluations, geostatistical methods known as global change of support allow prediction of the theoretical histogram and gradetonnage curves prior to interpolations or simulations of grades. Two methods commonly used by professionals to guide the choice of interpolation parameters and assess results are the discrete Gaussian model (DGM) and the indirect lognormal correction (IndLog). These models rely upon an estimate of the dispersion variance of the blocks, which is derived by numerical integration of the variogram model over a discretized block. Due to difficulties in obtaining well-formed traditional experimental variograms (especially in the presence of outliers and limited clustered data), many professionals prefer to use ‘normalized’ variograms such as correlogram (non-ergodic variogram), pairwise-relative, or variogram of the normal score transform. A series of simulations with different grade distributions and variogram models are used to assess the performances and robustness of the various variogram estimators with respect to the DGM and IndLog global change of support. Our results show that the traditional variogram, the correlogram, and normal score variogram have better performances, compared to pairwise, for both DGM and IndLog. Moreover, DGM provided better results than IndLog for the grade distributions that are not strictly lognormal. These findings provide valuable guides for geostatistics practitioners. IntroductionWhen reporting resource estimates,practitioners are required to follow generalstandards described in the NI43-101 (CIMguidelines), JORC, or SAMREC codes. One cangenerally recognize three main parts directlyrelated to the block model:•,Pre-processing: exploratory data analysis (EDA), domaining, capping, compositing, declustering, variography•,Processing: block size, neighbourhood, interpolation types (linear or nonlinear)•,Post-processing: classification, reporting.Pre-processing aims to simplify and strengthen the processing step. Ideally, domaining, capping. and compositing is aimed at defining a single homogenous population. During the processing phase, a common practice is to use a block size corresponding to the planned selective mining unit (SMU). In most precious metal deposits (gold, notably), the SMU size is frequently smaller than the recommended half data spacing (Journel and Huijbregts 1978), resulting in high estimation variance and either a high degree of smoothing if the regression slope is managed or a high degree of conditional bias if it is not. Most actual resource estimates are made using block sizes between one-quarter to one-sixth of the average data spacing, sometimes even smaller. In addition to the block size, the interpolation choices for the neighbourhood selection and interpolator (e.g. inverse distance (ID) or ordinary kriging) are often based on the Qualified Person’s (the QP) experience and some basic validation plots that often do not consider the conditional bias (e.g. trends or SWATHs plots, which are designed to compare two sets of population using a one-dimensional graph)."

Jan 1, 2018