Search Documents

By David A. Benjamin

The USBM (U.S. Bureau of Mines) studied mines, prospects, and mineralized sites in the Roberts WSA (Wilderness Study Area) in 1984. The 15,090-acre WSA, located 35 miles northwest of Eureka, NV, is underlain by alluvial deposits of Quaternary age, extrusive and intrusive volcanic rocks of Oligocene through Miocene age, and metasedimentary rocks of Cambrian through Permian age. The Roberts Mountain Thrust fault cuts through the WSA, dividing the metasedimentary rocks into upper and lower plate rock units. One mine, the Kelley, which produced 397 tons of lead-zinc ore prior to 1940, and two prospects are within the WSA; no resources were identified. Exploration for precious metal deposits is presently being conducted in and adjacent to the WSA on large claim blocks. The study area contains six sites in and near these claim blocks that have anomalous gold and silver. Detailed exploration is needed to delineate resources. High purity silica rocks are present in the WSA. Barite, phosphate, oil shale, and vanadium occurrences just outside the WSA may extend into it, but no such occurrences were observed during the USBM study.

Jan 1, 1986

By Anatol Wojtowicz

This research program was conducted to determine if respirable coal dust emanating from a continuous mining machine can be suppressed more effectively by a high expansion foam than by the water sprays conventionally used. A high expansion foam system was developed and tested on a continuous mining machine under actual operating conditions. The utility of the system was demonstrated. Test results tend to show that foam application is more effective than water sprays in suppressing respirable coal dust. However, because of the extreme variability of the test conditions, scatter in the sampling data, and other factors, not enough data was obtained to form a firm conclusion that foam is more efficient than a water spray in suppressing respirable coal dust. Sufficient statistical data was obtained, however, to indicate that foam is more efficient than water in suppressing total float coal dust.

Jan 1, 1974

By Gary W. Krantz

Fibered, portland-cement-based gunite products were applied in the Bureau of Mines Lake Lynn Laboratory Experimental Mine using a variety of pneumatic guns and gunning crews, The demonstrated wet-mix (with silica fume), dry-mix, and surface bonding products were sampled by the Bureau and subjected to a suite of engineering analyses. Gunite flexural and compressive strength, rebound, permeability, porosity, dust loading, shooting rate, crew requirements, and cost factors were evaluated. Steel, fiberglass, or polypropylene fibers were contained in all but two of the gunires tested. Both Bureau and private testing laboratory analyses are provided for some products. Electron probe micro-analysis and X-ray diffraction analysis were performed on the silica fume fraction of the wet-mix gunite to characterize the dust. Aggregate size fraction distribution analyses were performed to provide strength relationships. Results indicate that all of the commercially available fibered-gunite materials tested can provide beneficial sealant, spall prevention, or roof stability control attributes for underground mining environments when applied by an experienced crew using a well-maintained gun, in accordance with product manufacturers' recommendations and when used for the designated purpose.

Jan 1, 1984

By Joseph V. Mather, E. H. McCleary

"INTRODUCTION Workmen are transported in shafts in various types of cages or skips, most of which were designed primarily for hoisting cars and materials. Therefore, in general the cages or skips are not completely enclosed, adequate and gates are not always provided, and at many mines signaling devices and telephones are re¬stricted to those at the various landings in the shafts.Shaft accidents are usually severe - frequently fatal - and as a rule such an accident is caused by failure to comply with company rules or by ignoring them.Sixty men were killed and 555 men were injured in shafts of the anthracite and bituminous coal mines of the United States during the 5-year period 1938-42. 4/ Many of these accidents could have been prevented by having properly enclosed cages and adequate locking devices on doors to prevent workmen from falling into the shafts.The officials of the Heidelberg Coal Co. contemplated utilizing an old coal-hoisting shaft as a man-hoisting shaft; however, it was their desire to avoid the use of the conventional cage and to try to provide a safer means of transporting men in the shaft. Investigations and studies made by the officials revealed that an elevator similar to those used in large buildings would be more economical in first cost, maintenance, and operating costs would be less, and it would be safer and more convenient for the workmen. Effective safety devices for such elevators have been developed to such a high degree that those properly installed seldom fail. The elevator or man cage finally chosen cannot be pulled above the top landing through mechanical or man failure; it stops automatically at each landing and cannot be moved while a door is open; when the cage leaves the landing the doors opening to the shaft are automatically locked by mechanical and electrically operated locks; electric lights, telephone communication, and push-bottom controls are available on the cage, and adequate safety switches and overspeed controls are provided."

Jun 1, 1947

By A. D. Hahn

This report describes reconnaissance by the Federal Bureau of Mines of titanium-bearing sandstone in Kemper County, Miss. The purpose was to determine the ilmenite, rutile, and associated heavy-mineral content of black-sand-bearing Eocene deltaic formations" The investigation was part of a survey of titanium resources of the United States. Ilmenite (FeTi03), an iron-titanium oxide, is the major titanium-bearing mineral consumed in the titanium pigment industry. Rutile (Ti02), titanium oxide, is used mainly in producing welding-rod coatings and titanium metal. The fieldwork was conducted during the first half of November 1959. Seven holes, totaling 304 feet of bore, from which 64 samples of cuttings were taken, were drilled in the north-central part of the county; and two holes, totaling 172 feet of bore, from which 34 samples of cuttings were taken, were drilled in the southeastern part.

Jan 1, 1961

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By Fred N. Kissell

A parachute-type stopping intended for changing the course of mine ventilation air during mine emergencies has been designed and tested. Some production uses are also visualized for metal mines. Preliminary tests in the laboratory and underground indicate that the parachute stopping is a workable concept, but further developmental research is required.

Jan 1, 1975

By W. P. Yast, R. R. Slyers, J. H. Hildebrand

 The Bureau of Mines, in conducting investigations of atmospheres in mines and tunnels for the purposes of determining and combating hazards to the health and safety of workers, has from time to time closely cooperated with municipal, State and Federal agencies in safety work in engineering and ventilating probleme. Recently the writers have conducted experiments with animals and men breathing helium-oxygen mixtures under pressure. The object of this work was to determine whether helium-oxygen atmospheres can be utilized to advantage in place of normal air for caisson and diving work. In such work the permissible pressures and times of compression and decompression are limited by the physiological effects on man. The major effect is that the nitrogen, (which is the inert con- stituent of normal air and is absorbed by the body tissues and fluids in abnormal amounts when under pressure,) tends to form bubbles in the tissues on too rapid discompression from high pressures. The Bureau of Mines is interested in this problem on account of the pos- sibilities of mitigating caisson illness in tunnel construction and other engine eering operations requiring men to work in compressed air. In addition, the Navy Department is interested on account of the possibilities for extending the range of salvaging and marine engineering operations. The results of the experiments conducted by the writers lead to the following conclusions: Helium is without odor or taste and has physical properties which promise to be of interest physiologically and which have been found to have possibilities of creat practical use, especially in making a synthetic atmosphere that will re- duce the hazard of caisson disease. The substitution of helium for the nitrogen ordinarily present in the air we breathe has been found to result in an atmosphere which it as respirable as that provided by nature. The results obtained indicate that helium not only has the advantage of being less soluble than nitrogen, but

Feb 1, 1925

By R. R. Wells

This report summarizes the results of preliminary mineral-dressing studies by the Bureau of Mines on five samples of copper-bearing ore from various Alaska de-posits. The work on each sample was not extensive enough to warrant individual publication. The results, however, indicate the possibilities and limitations of concentration of the respective ores. The information therefore may be helpful in future development of these ore bodies. Four of the five samples tested were submitted to the laboratory by engineers of the Bureau of Mines as part of the examinations and survey investigations of strategic-mineral deposits in Alaska. This program is conducted to assist development of mineral resources in the Territory and particularly to aid economic exploitation of marginal or complex ores. The fifth sample was submitted by engineers of the Defense Minerals Exploration Administration.

Jan 1, 1956

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington, The investigation consisted of transit and topographic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds Were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and analyzed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing new sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest.

Jan 1, 1948

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By J. L. Ambs

The U.S. Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mines using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterbath exhaust conditioners. These were evaluated in three underground, mines, to determine their effectiveness in reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90 pct at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such 'as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.

Jan 1, 2010

By D. J. MacDonald

This U.S. Bureau of Mines report reviews published information on synthetic berlinite (AlP04) and suggests experimental conditions requisite for its production. Berlinite is a piezoelectric material with potential use as a substitute for quartz in the crystal oscillators, which are components of electronic and electroacoustic equipment. Information gathered here (mostly from published sources) includes historical background, physical properties, end-use applications, criteria of quality, and physio-chemical factors involved in berlinite crystal growth. It is concluded that growing large high-quality berlinite crystal would require high-purity starting materials in an autoclave equipped with a noncorrodible liner and operated with temperature control of ±O.OO5 ac over a range of 250 to 350 ac.

Jan 1, 1995

By Thomas V. Falkie, R. Venkataramani

Table

Jan 1, 1972

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, decreased about 24% in 1992. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a significant increase in unit value and decrease in the quantity produced. Garnet showed a 6 % increase in quantity and a 36 % decrease in unit value. Staurolite decreased about 27 % in the quantity produced and value compared with those of 1991. The fused aluminum oxide industry showed a slight increase in the quantity produced and a 4 % increase in the value of production. The silicon carbide industry saw a 7 % increase in the quantity produced and a 10 % increase in the value of production. Combined, the industries increased 4 % in quantity and 6 % in value compared with those of 1991.

Jan 1, 1992

By K. K. Kelley, L. B. Pankratz, W. W. Weller

The heat capacity of columbium (niobium) carbide (CbC ) was measured over the temperature range from 51 ° to 298 ° K, and the entropy at 298.15° K was evaluated . Also , the heat content above 298.15 ° K of columbium carbide was measured to 1,800 ° K. The results were combined with the known heat of formation at 298.15 ° K to obtain values of the heat and free energy of formation over the temperature range from 298.15 ° K to 2,000 ° K.

Jan 1, 1964

By B. L. Razzaboni, P. Bolsaitis

"The formation of reactive oxygen species resulting from the interaction of silica dust particles with red blood cell membranes was investigated; particularly, the effect of surface hydroxyl (silanol) group concentration on the rate of formation of such reactive oxygen species was investigated. The rate of formation was measured indirectly through the effect of catalase, a hemoprotein peroxidase, on silica-induced hemolysis. It was found that the addition of exogenous catalase to erythrocytes markedly reduces the hemolysis caused by silica particles. Furthermore, the amount of catalase required for deactivation of silica per unit area of particle surface is lower for fumed silica particles and calcined crystalline particles than for uncalcined, crystalline silica, suggesting a correlation between the concentration of OH groups at the silica particle surface and its potential for generation of H2O 2• The addition of albumin, a copper chelator, also decreases hemolysis. These results suggest that the hemolysis caused by silica particles is at least partly related to the formation of H2O2 at the particle surface and its subsequent reaction with Cu+ ions. The relationship between the concentration of surface silanol groups on the silica surface and the amount of catalase required to decrease hemolysis may also provide a method for testing potential fibrogenicity of respirable dusts. IntroductionReactive hydroxyl groups on silica surfaces are known to be cytotoxic and are believed to play a major role in silicosis (1-9). It has been proposed that this cytotoxicity results from hydrogen bonding to cell membranes and a resulting increase in membrane fluidity and permeability (4). Surface hydroxyl groups on silica surfaces have also been shown to interact with carbonyl oxygens in cell membranes (1,5). An extensive study by Nolan et al. (6) of the relationship between the negative surface charge resulting from ionized silanol groups and the hemolytic activity of crystalline a-quartz (Min-U-Sil) has shown a positive correlation between hemolytic activity and the surface concentration of silanol groups. These authors demonstrated that the hydrogen bonding of polyvinyl-N-oxide (PVPNO) with silanol groups, as well as the bonding of metal cations to the ionized sm- groups, results in significant decreases in hemolytic activity. Furthermore, it has been found that the complete removal of surface hydroxyl groups from the surface of respirable silica particles nearly eliminates the hemolytic potential of silica (7), suggesting that hydroxyl groups might be involved in other cytotoxic processes associated with silica-induced lung injury. Reactive oxygen species have been .implicated in cellular damage caused by respirable silica particles. Evidence for the presence .of oxygen radical species (02, OH°, H2O2) generated by silica, especially on freshly formed surfaces, has been produced by various investigators. Kalbanev et al. (8) detected H2O 2 in aqueous suspensions of quartz. Electron spin resonance and spin trapping by Shi et al. (9) confirmed the presence of OH"" radicals in aqueous suspensions of quartz, and Gulumian and van Wyk (10) suggested that both glass and quartz produce hydroxyl radicals in the presence of H2O 2 • Gabor et al. (11) detected the presence of malondialdehydereactive lipid peroxides (i.e., lipid-0°) in cultures of macrophages and respirable silica particles using the thiobarbituric acid (TBA) reaction test. Will (12), however, reported that iron enhances the TBA value of peroxidized lipids, and Scheulen and Kappus (19) found that catalase augmented malondialdehyde formation, thereby increasing the TBA values."

Jan 1, 1990

By J. E. Chilton

The Bureau of Mines has developed a portable flammable gas detecting system for estimating the flammable gas concentrations in a mine containing one or more combustible gases at concentrations up to 100 vol pct. With this portable detecting system, mine rescue or recovery personnel can quickly determine if they are working in a potentially explosive gas atmosphere and either leave the area or make appropriate changes in the fresh air ventilation of the mine to render the area safe. The detecting system uses a commercial, intrinsically safe, flammable gas detector with a range from 0 to 5 vol pct methane (CH4). The flammable gas detector has a catalytic heat-of-combustion sensor that can detect all flammable gases that would be encountered in a mine including methane (CH4), ethane (C2H6), carbon monoxide (CO), and hydrogen (H2). To determine the mine gas concentration, the rescue worker dilutes a sample with fresh air carried within the detecting system. The concentration of the diluted sample is then measured with the permissable flammable gas detector. The actual mine gas concentration is calculated from the product of the indicated diluted gas concentration and the system dilution ratio using a pocket calculator or the nomograph on the side of the unit.

Jan 1, 1987