Search Documents

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978

By Thomas C. Mowatt

Preliminary Bureau of Mines studies of mafic igneous rocks collected from the Rabbit Creek area, northwestern Alaska, indicated concentrations of platinum (412 to 1,406 ppb) and palladium (343 to 892 ppb) in five of eight samples analyzed. The samples represent boulders and cobbles of mafic/ultramafic rocks from this locality. They are not from outcrop. Petrologically, (on the hand specimen scale) the samples are crudely to well-layered and are troctolitic ± gabbroie in character, with primary igneous mafic minerals strongly altered. Small patches of interstitial sulfide minerals, including chalcopyrite, bornite, pyrrhotite, pyrite, and covellite are associated with these altered zones and elsewhere through the specimens. Copper values ranged from 0.1 to 0.3 pct in samples analyzed semiquantitatively; nickel, cobalt, and chromium contents are low. Chemical, mine alogic, and petrographic relationships suggest that the rocks of similar character outcropping in northwestern Alaska could also be considered as prospective for- concentrations or platinum, palladium, and copper.

Jan 1, 2011

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929

By L. B. Pankratz

The heat contents of the sesquioxides of erbium, holmium, thulium, and ytterbium (Er203, Ho203, Tm203, and Yb203) in the cubic crystalline form were measured over the temperature range from 298° to 1,800° K. The erbium and holmium sesquioxides gave regular heat content-temperature curves. Thulium sesquioxide had a minor thermal anomaly near 1,680° K, with a heat absorption of 310 cal/mole; similarly, ytterbium sesquioxide had a minor anomaly near 1,365° K, with a heat absorption of 150 cal/mole. The heat content results are presented in both tabular form (at 100° intervals) and in algebraic form. Entropy increments, corresponding to the tabulated heat content results, also are listed.

Jan 1, 1963

By T. J. Ballard

The Ore Knob mine, in Ashe County, N.C., was one of the largest producers of copper in the eastern states during the 1870's. The ore occurs in a fissure vein, which strikes N. 64° E. and dips nearly vertical. The country rock is granite gneiss. Drilling indicated that the vein structure is approximately 200 feet wide and 1,500 feet long. The vein material shows evidence of replacement of the original gneiss by sulfides. Solution cavities in the vein were noted in some places. The ore minerals and pyrrhotite, chalcopyrite, pyrite, and minor quantities of sphalerite. The gangue contains biotite, magnetite, albite, calcite, and many silicate minerals.

Jan 1, 1948

By W. H. Tomlinson

During the 9 years ended December 31, 1938, 188 fatalities resulted from preventable accidents in and around the coal mines of Indiana; 173 of these occurred at underground mines and 15 at stripping or open-cut operations. In addition, there may have been other unrecorded fatalities during this period. The two organizations receiving notice of accidental deaths at coal mines in this State are the Division of Mines and Mining and the Indiana Industrial Commission. Only deaths occurring at underground mines employing 10 or more men are reported to the former, as neither strip mines nor underground mines employing fewer than 10 men cone within the purview of the Indiana mining law. The mine inspectors have no Jurisdiction over this latter group of mines and do not inspect them. Fatalities at small "wagon" mines and open-cut operations are supposed to be reported to the Industrial Commission; however, in many instances deaths at small mines are not reported, the only record being a death certificate filed with the county or corporation health officer. Thus, many deaths in small mines escape attention, especially when the victim succumbs some time after the injury was received. The data presented here on fatalities in Indiana, during the past 5 years include several instances in which the only record available is a death certificate; possibly others have been overlooked. From 1934 to 1937 the fatality record was progressively worse, that of the larger underground mines in 1937 being more than twice the average for these mines for the previous 4 years and only slightly less than twice the average for all mines, including open-cut operations. The increase in deaths during 1937 was due to two explosions, with 20 fatalities in one and 2 in the other. The number of deaths in the larger underground mines was considerably less in 1938 than in the previous 4 years, but there was no improvement in the number of fatalities at the small mines, or at open-cut mines.

Jan 1, 1940

By Bruce D. Hanson

The Bureau of Mines conducted a series of ignition tests with two types of conical bits (plumb bob and pencil) used on continuous mining machines, to determine their ignition potential at various bit speeds, cut depths, and wear conditions. The tests were conducted using single bits mounted on a 34-in-diam drum in a Bureau ignition test facility. The bits impacted blocks of Berea sandstone in a 6.5 pet methane atmosphere at various bit speeds and cut depths. In a new condition, the plumb bob bits were considerably more incendive than the pencil bits, causing ignitions in 32 of 35 tests at 60 rpm, compared with ignitiolls in 2 of 22 tests for the pencil bits. The results from new bit testing also show that reduction of bit tip velocity to 180 fpm does not eliminate ignition potential. When subjected to progressive wear, bits of both types were more incendive when they were locked in place, unable to rotate, than when they were free to rotate.

Jan 1, 1983

By Lloyd A. Morley, Robert Stefanko

A major difficulty encountered during the research was that nation¬al countries (almost world-wide) are in the process of revising their electrical hazard reduction standards. Their principal goal is to align their standards with the International Electrotechnical Commission (IEC) Recommendations Publication Series 79. (31-37) Additionally, CENELEC is requiring all Common Market countries to harmonize their standards. (85) However in the coal mining industry some hazard re¬duction techniques are not being accepted because some systems may not be applicable. Therefore, past literature might not directly relate a country's current feeling about explosion-proof standards. An authority in the United Kingdom (which has been a leader in hazard reduction mainly through work at the Safety in Mines Research Establishment) brought up an additional point. (15) He hopes that since revising British standards BS229 into BS4683, with the intention of corresponding with the IEC 79 series, the recent CENELEC harmoni¬zation process will also follow IEC. (8, 9, 10) The past trend in other major Common Market countries prior to CENELEC's requirement results in the authors' speculation that the standards will be pattern¬ed after the IEC Publications. (5,17,60,84,102) Several letters were sent to the East Block countries but, disa¬ppointingly, replies were dispatched only from the USSR and Poland. Recent Polish standards (1973) were received, and a very close match to the IEC Publications has been noted. (76,77) Because of their economic community, it is extremely logical to assume that the East Block stand¬ards are therefore in concurrence with the IEC. Japanese specifications also appear to be compatible with the IEC Recommendations. (42,43)

Jan 1, 1974

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By R. H. Nicholas

Shuttle cars have undeniably proved their worth as a means of transporting coal underground; however, several factors have arisen in connection with their possible improvement. This report .discusses the effect of shuttle cars that employ rough-tread and smooth-tread tires on mine roadbed, the amount of dust thrown into suspension by the use of such tire treads, and the service rendered by each type of tire. Involved, also, in this study are observations on the use of different amounts of calcium chloride on the haulageways.

Jan 1, 1949

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By Michael D. Dunn

The Bureau of Mines evaluated a quartz schist formation within the Blue Joint Wilderness Study Area which was identified as having a "high potential" for copper-silver-cobalt-barium resources. Stratiform and remobilized copper occurs near, and bedded barite within, the study area. In addition, the black to gray Proterozoic quartz schist may correlate with the Yellowjacket Formation which contains cobalt-copper-gold-silver deposits at Blackbird, ID, about 30 miles to the south. Eighty soil and 43 rock samples collected across the quartz schist formation were analyzed for gold, silver, copper, cobalt, and barium. During the reconnaissance and sampling, particular attention was given to looking for malachite (copper carbonate) and erythrite (cobalt arsenate, also known as "cobalt bloom"). The sample analyses and geology in this localized area do not provide enough evidence to support the "high potential" designation for copper-silver-cobalt resources. Barium potential still appears high, however.

Jan 1, 1987

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By Philip C. Tully

This Bureau of Mines report contains experimentally determined vapor-liquid equilibria data for a helium-nitrogen-methane mixture with a nominal composition of 15, 60, and 25 mole-percent, respectively. Measurements of the equilibrium phase compositions were obtained by means of a windowed cell, in conjunction with an automated chromatograph and a special analyzer for low helium concentrations. The data presented include a comprehensive table and eight graphs depicting phase compositions, vaporization ratios, and correlations with a previous study of two helium-nitrogen-methane mixtures of different compositions.

Jan 1, 1976

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By N. A. Gokcen

In this Bureau of Mines report, appropriate equations correlating the activity of water with the activities of electrolytes in binary and multicomponent solutions have been derived for computer calculation. It was found that the half-integer power series are far superior to the integer power series, for both types of series having the same number of terms. The pro-posed method of calculation is capable of accurately yielding the activities of all components from the measurements of the activity of a single component at various concentrations. This method replaces the cumbersome and objection-able method of graphical integration of the Gibbs-Duhem equation. Two novel methods are proposed for determination of activities of electrolyte solutions important in hydrometallurgy; (1) Water vapor pressure measurement by differential pressure transducers having an accuracy of 0.001 pet, and (2) transpiration method with an inert gas bubbled through concentrated solutions followed by the analysis of the evaporated and redissolved electrolytes with specific ion electrodes having a sensitivity of ±10-10 molal. The first method is suitable for nonvolatile electrolytes, and the second, for volatile electrolytes such as hydrogen halides, HN03, H2S03, etc. The existing methods of estimation of ionic activities have been surveyed, and the best method has been selected, discussed, and summarized.

Jan 1, 1979

By Thomas M. Barczak

The Bureau of Mines is conducting research to optimize the capability of mine roof supports so that the selection and design of these supportsare compatible with the conditions in which they are to be employed. This report describes a study that investigates three parameters influencing the load-carrying capability of wood crib supports: height, configuration, and horizontal displacement. Four crib heights, four parallelogram configurations, and three ratlos of horizontal-to-vertical displacements were tested on full-scale wood crib supports in a mine roof simulator. Test results indicated a reduction in load-carrying capability for increases in crib height. Increasing the contact area by changing the intersecting angle between crib blocks to form parallelogram configurations provided a slight increase in load-carrying capability for the first 10 to 12 in of vertical convergence, after which the cribs became more unstable, resulting in significantly less load-carrying capability. Horizontal displacements did not appreciably affect the load-carrying capability of wood crib supports for the range of vertical displacements (less than 10 in) likely to be encountered underground. This report documents these tests and postulates some explanations of failure mechanics for the observed behavior.

Jan 1, 1988

By Vernon C. Allison

The explosibility of coal dust has long been recognized by competent investigators as constituting one of the dangers of mining coal and in the use of pulverized coal as a fuel in industrial plants. The Bureau of Mines has carried on extensive series of experiments dealing with this subject, and has not only developed methods for the practical prevention of this danger, but in the, course of these experiments has developed a standard method of determining the relative explosibility of coal dusts and other organic dusts.3 Oil shale contains compounds 'of carbon and hydrogen that are either of a petroleum nature and are strongly ,adsorbed upon the incombustible part of the shale, or else are present in the shale as a compound ("kerogen") which has the property of changing into petroleum-like products when acted upon by heat. The oil shales may contain varying amounts of the organic matter, ranging from a trace to more than 66 per cent, depending upon their richness; therefore, it is important to know whether the dusts formed in mining and handling these oil shales are explosive when mixed with air and if so, to indicate remedial measures. This paper gives the results of explosibility tests of several pulverized oil shale's, selected as being typical of those which in the future may be used in commercial shale-oil production test on a sample of typical Colorado oil shale has been., published in an earlier paper.4

Jan 1, 1926