Search Documents

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer's sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 2010

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By James P. Bennett

To identify construction materials for emerging technology in chemical and metallurgical processes, the Bureau of Mines investigated the acid resistance of ceramic materials. Eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a five-claybonded silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed for 110 days to 20 wt pct HCl at 50°, 70°, and 90° C and to 30 wt pct HCl at 70° C. Statistically significant changes in cold crushing strength, volume, and weight were generally small or not detected. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. The carbon brick sample had the best acid resistant properties with a maximum total leached ion weight loss of 0.004 wt pct. The silicon carbide, the silica, and one of the fire clay bricks also had excellent acid-resistant properties.

Jan 1, 1983

By H. P. Greenwald, H. C. Howarth

There was reported in Bureau of Mines Technical Paper 5754/ a series of tests to determine the compressibility and bearing strength of specimens prepared from blocks of potash salt obtained from a mine near Carlsbad , N. Mex . The events leading up to the investigation were sketched in a foreword by George S. Rice , then chief mining engineer of the Bureau ( retired September 30 , 1937 ) ; this foreword also gives a discussion of the possibility of increasing the ultimate total recovery of the potash salt by " second mining" of pillars or by use of a longwall system . In June 1936 , Rice and the senior author visited Carlsbad with H. I. Smith , chief of the mining division of the Geological Survey , to observe mining then in progress and to discuss with the management of one of the mines records of convergence of roof and floor which they were obtaining . It developed that serious thought was being given to the possibility of roof failure resulting from shear at the faces of pillars . There was envisioned the danger of such cracks extending upward to water - bearing strata . Obviously , the simple compression tests of the potash salt then being made would throw no light on this question , and tests of assemblies of potash and roof salts would have to be made . In this connection it is to be remembered that in the mine no sharp division exists between the potash salt being recovered and the nearly pure halite which forms the roof . The interlocked crystalline structure is continuous , and there is merely a very rapid decrease in the proportion of sylvite in a short distance vertically . Figure 2 of Technical Paper 575 shows that two samples near the top of the salt being mined contained , respectively , 51 and 65 percent potassium chloride . Contrasted with this is an analysis of the roof salt given on page 24 of that publication , which showed only 3.6 percent potassium chloride . As the data given in Technical Paper 575 show , the roof salt is much less plastic than the potash salt . The immediate roof may then be thought of as a more rigid stratum of indefinite extent resting on and continuous with yielding supports and loaded uniformly at the rate of 900 to 950 pounds per square inch . Just what thickness of the salt should be considered as immediate roof is uncertain .

Feb 1, 1938

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

The Production Profile Program is written for use on a Digital Model PDP 11/70 computer using a Fortran IV level G language. It may be run on any system which uses G level or an upward compatible version of Fortran IV language. Please note, however, that the Model PDP 11/70 for which the program was written is programed to read DEC026 type keypunching. If the user's computer is programed for another type of keypunching it may be necessary to re-keypunch the Production Profile Program. The Production Profile Program uses a fourteen card input. The data must be keypunched according to the layout described in detail in the multiple card layout forms (following). The output from this program must be printed on wide paper, as a full 120 columns are used. The samples of output at the back of this appendix have been reduced for inclusion in this report.

Jan 1, 1977

By J. M. Singer

Quenching distances for flames of methane-coal dust mixtures were determined with air and oxygen-enriched air. Coals used were Pittsburgh, Sewell, and Pocahontas No.3. Quenching distances were greater for flames of hybrid mixtures of coal dust and methane than for methane flames of corresponding stoichiometry. From the data of quenching distances and methane-coal dust concentrations was calculated the quenching equivalence, which is the increase in coal dust concentration required to maintain a given quenching distance value as the methane concentration decreases. These equivalences could be useful in identifying hazardous methane-coal dust mixtures in mines.

Jan 1, 1966

By M. M. Tilman

As part of ongoing research to improve mine safety, the Bureau of Mines conducted research on the corrosion of friction rock stabilizer steels in five Missouri lead and iron mine waters. Electrochemical corrosion tests, including evaluation of pitting tendency, were performed on two types of high-strength, low-alloy (HSLA) steels and galvanized steel in four Missouri lead mine waters and one Missouri iron mine water. The tests were conducted at in-mine water temperatures in both air-saturated and deaerated waters. Static, weight-loss corrosion tests were also conducted on HSLA steel specimens in the five Missouri mine waters for 2,900-h duration at average in-mine water temperatures and air-dissolved oxygen contents of 6 to 7 ppm. Corrosion rates determined by the weight-loss tests were roughly comparable with rates determined electrochemically in deaerated waters containing 0.3 to 0.5 ppm dissolved oxygen content. Passivation of specimen (nongalvanized) surfaces in air-saturated waters resulted in very low electrochemically deter- mined corrosion rates. Pitting-tendency was generally higher for both HSLA steels in air-saturated waters than in deaerated waters. Galvanized steel generally exhibited higher tendency to pitting in the deaerated waters than in the aerated mine waters.

Jan 1, 1985

By Joe L. Castagno, Kenneth H. Johnston

Several hundred membrane - filter tests were made as part of a program to develop equipment and procedures to evaluate the quality of waters and to determine the quality of water suitable to efficiently flood oil sands of known permeability . Results indicated that neither the color of the water nor that of the precipitate on a membrane filter is a criterion for determining the quality of injection water . Reasons for poor water quality include poor operation of filtering systems , dirty filtering aggregates , excessive amounts of oil in injection water , commingling of incompatible waters , and excessive use of chemicals . A good water is required to efficiently flood sands of low permeability , but fair results may be obtained in flooding more permeable sands with poorer quality water .

Jan 1, 1964

By W. H. Tavenner

The Bureau of Mines gathered test data on the use of a continuous borer in mining an anthracite bed, which was 30 feet thick on a pitch of 15° to 45°. Gangways were driven with the continuous borer, ventilation openings between gangways were driven with a large-diameter auger, and the blocks of coal between completed gangways were mined by the long-hole method, Conveyors were used to transport the mined coal. The continuous borer operated on a coal floor that was frequently soft because of heaving. The continuous borer could not bore openings on a grade exceeding 27 percent (15° pitch). Because 150 was also the lower limit of the pitch, of the bed, the continuous borer was used only to drive gangways. The continuous borer virtually filled the workplace, leaving insufficient space to place heavy-duty timber and cushioning material between the timber and coal back to allow for normal expansion of the uncut coal. The light? weight yieldable steel arch against the coal back gave inadequate support to control convergence, which in a disturbed area sometimes occurred with explosive violence. This exposed the machine operator to a hazardous condition, since a satisfactory solution could not be found, the company discontinued the use of the continuous borer.

Jan 1, 1966

By G. V. Sullivan

This report summarizes the results of a preliminary study concerning manganese extraction from low-grade dolomitic materials from the Philipsburg district in Montana by the Dean-Leute ammonium carbamate process. Studies were made to determine the relationship between the variables involved in treating these materials by a roast-leach process and the amount of manganese extracted. The variables studied were the roast temperature, the roast particle size, the molar ratio of NH3 to CO2 in the leach solution, the liquid-solid ratio in leaching, the leach time, and the size of the particles being leached. The roast-leach studies were statistically designed, and the experimental results were evaluated by an analysis of variance.

Jan 1, 1962

By David R. Hanson

Transient electrical noise events pose serious problems for data acquisition systems used in monitoring acoustic emissions in laboratory and field environments. The U.S. Bureau of Mines has designed and constructed a trigger discriminator circuit for use in ultrasonic acoustic emission studies. Designed for use with signals in the frequency range of 50 to 400 kHz, the instrument examines .incoming signals for frequency content, amplitude, simultaneity, threshold crossings, and number of channels above threshold. If preselected criteria on these properties are met, a plus 5-V pulse is output that may be used to trigger a data acquisition system, allowing rejection of noise events that do not possess useful information. The system was designed for four input channels, but may be expanded to more channels with minimal design changes.

Jan 1, 1995

By A. A. Cochran

The objective of the research was to determine the final distribution of cerium additions to steel, their effect on sulfide inclusions, and the usefulness of radiotracer methods in investigating steel problems. Fifty-gram heats of steel were prepared that contained either cerium 141 and nonradioactive sulfur, or sulfur 35 and nonradioactive cerium. These steels were studied by autoradiography, measurements of their surface radioactivities, optical microscopy, and chemical analysis. Samples of the crucibles were analyzed quantitatively for cerium or sulfur by radioactivity counting methods. The addition of cerium to steel melts reduced the size and number of iron sulfide inclusions in the resulting steel. A significant fraction of the sulfur and most of the cerium penetrated into the MgO crucible during the melting operation, The cerium inclusions in steel were identified as cerium sulfide. Radiotracer methods were found to be versatile and highly sensitive.

Jan 1, 1963

By Pablo Velasco

The Ecuadorean mineral sector and overall economy have retained their traditional dependence upon the production and export of hydrocarbon products. Exports of crude oil and its products accounted for 62% of the country's export earnings in 1985. Ecuador's major mineral commodities produced and exported were cement, gold, limestone, liquefied natural gas, liquefied petroleum gas, natural gas, natural gasoline, crude petroleum and condensate, raw steel, semimanufactured steel products, and sulfur.

Jan 1, 1987

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By Donald P. Blasko

The Bureau of Mines investigated two areas of oil and gas seeps in the north-central Gulf of Alaska--Katalla River to Bering River and Cape Yakataga to Yakutat Bay to determine (1) whether previously reported seeps are still active, (2) the characteristics of the seeping hydrocarbons, and (3) the amount of bitumen contained in the drainage leaving the seeps and entering the Gulf of Alaska. Thirteen separate oil seeps, six bitumen deposits, and eight gas seeps were located, sampled, and analyzed. The oils ranged from 35.2° to 14.1° API gravity and had sulfur contents from 0.53 to 1.31 wt-pct. Bitumen samples had API gravities from 2.4° to 14.6° and sulfur contents from 0.28 to 0.88 wt-pct. Gas samples had specific gravities ranging from 0.577 to 0.883 and caloric values from 724 to 1,427 Btu/cu ft. A total of 63 water samples obtained from seep locations and seep drainages were analyzed by atomic absorption spectrophotometry for ionic content and by solvent extraction for hydrocarbon content. Although some of the water at the oil seeps had a bitumen content as high as 246,000 mg/1, the amount of hydrocarbons actually reaching the Gulf of Alaska averaged <0.2 mg/1.

Jan 1, 1976