Search Documents

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By J. G. Donaldson

A bench-scale method for recovering lead and zinc from slimes and mill tailings from the Tri-State District of Missouri, Oklahoma, and Kansas was developed by the Bureau of Mines. Dilute hydrochloric acid, containing sodium chloride, and chlorine gas were used to decompose the mineral constituents. Lead was electrolyzed from the pregnant acid solution, and zinc was precipitated from the depleted electrolyte by neutralization with lime. Up to 98 percent of the lead was recovered in an impure lead electro- deposit assaying approximately 85 percent lead. Zinc recoveries up to 90 percent of the total were attained in a precipitate assaying approximately 40 percent zinc.

Jan 1, 1963

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional ore-processing methods that will confine and permit controlled disposal of radioactive liquid wastes. Stream and ground water pollution from radio-active nuclides, principally radium 226 and thorium 230, in liquid wastes from uranium mills can be minimized by reusing the waste solution within the mill. Such reuse of waste solution in an acid leach-resin-in-pulp flowsheet was investigated in the laboratory. The process consists of acid leaching for dissolution of the uranium, sand-slime separation and countercurrent decantation washing for recovery of a pregnant slime slurry, and the use of ion-exchange resin for recovery of uranium from the slurry. Reuse of clarified barren effluent for washing in the simulated mill circuit was carried through 55 cycles. Dissolution of uranium from the ore averaged 97.5 percent. Washing efficiency of 99.9 percent was attained when using 4.35 volume tons4 of combined barren effluent and makeup water per ton of ore. Absorption of uranium from the pregnant slime slurry by an ion-exchange resin averaged over 99.9 percent.

Jan 1, 1962

To provide a means for mechanically separating and recovering nonferrous metals continuously from non-magnetic reject material produced at scrap automobile shredding facilities. Approach The Bureau of Mines developed a water elutriator system that separates metals from shredded scrap auto-mobiles based on differences in specific gravities. A premium-quality product, containing aluminum, magnesium, lead, zinc die cast, copper, copper alloys, and stainless steels, is obtained. How It Works Mixed nonmagnetic reject material currently being separated at automobile shred-ding facilities is introduced onto the top of an upwardly flowing vertical column of water. The water, overflowing a weir in the top of the vertical column, carries with it the floating, lightweight waste materials, mostly combustibles, while the heavier pieces sink through the rising water. Medium-density substances such as glass, rubber, and heavy plastics are carried off through a side port, located in the upper third of the column. The cleaned, mixed metal product sinks to the bottom and is continuously removed from the base of the column with a bucket elevator having perforated buckets. All three categories of material are removed from the system on separate wire mesh belt conveyors. Most of the water drains through the belts into a holding tank and, after settling, is recirculated back through the elutriator column. The purity and recovery of the metal product are influenced by two elutriator operating variables: the flow rate of water through the vertical column, and the height of the overflow weir at the top of the column.

Jan 1, 1983

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By R. G. Nelson

This report covers investigations of the Bureau of Mines for the period of June 15, 1952, to June 15, 1953, on a research project for the Materials Laboratory, Wright Patterson Air Force Base, Dayton, Ohio. The primary purpose of this investigation was to make high-purity chromium-base alloys having room-temperature ductility and high-temperature strength. The Nonferrous Metals Branch of the Bureau of Mines, Albany, Oreg., has, during the past 7 years, developed on a laboratory scale a hydrogen treatment method for making high-purity chromium that can be fabricated into thin sheet and wire. This material can be bent at room temperature. The object of this investigation was to use this material to develop improved chromium-rich alloys for high-temperature uses.

Jan 1, 1955

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By T. O. Llewellyn

Laboratory batch and semicontinuous studies showed the feasibility of using methylene bromide and trichloroethylene in heavy liquid cyclone concentration of a Nevada brucite ore. Cyclone tests of minus 20- plus 200-mesh material at specific gravities of 2.42 and 2.44 recovered 71.6 to 74.9 percent of the MgO at grades of 95.5 and 95.4, respectively. Neither increasing the feed pulp density from 5 to 25 percent solids, nor varying feed pressures from 25 to 60 psig had any apparent effect on the heavy liquid separation.

Jan 1, 1971

By J. W. Eckerd

Metal production rates of 42 to 45 tons per day were obtained with hollow-core anthracite briquets in an experimental blast furnace. Tuyere pressures were about the same for both coke and briquet operations, but from 150 to 175 pounds more of briquets were required per ton of metal than were needed with coke. Furnace operations were comparatively smooth, furnace hanging occurring less often than in previous tests with anthracite briquets. Dust production was substantially higher than with coke, however, and metal quality could not be controlled by corrective burdening and moisture control.

Jan 1, 1968

By John S. Berber

Olefin and paraffin mixtures (C10-C16 and C10-C22) were separated from low-temperature lignite tar by urea adduction and sulfated to yield secondary alkyl sulfate detergents. The C10 ?C16 secondary alkyl sulfate showed a 99.3 percent biodegradability, and the C10-C22 fraction showed a 96.8 percent biodegradability, exceeding the required standard of 80 percent for the biodegradability of anionic detergents in washing and cleaning compounds. Chlorination of paraffins yielded a detergent of 93.2 to 93.4 percent biodegradability.

Jan 1, 1968

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By Wilbur I. Duvall

A linear array of shot and gage holes 30 feet deep in a granite outcrop was used to compare the size and shape of radial strain pulses produced in the rock when short cylindrical charges of cast composition B were detonated axially or at one end. The axially detonated charges produced radial strain pulses that had shorter rise times and larger peak strain than the strain pulses produced by end detonated charges.

Jan 1, 1965

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By John J. McClelland

The U.S. Bureau of Mines formed a team in 1991 to begin developing a long-range research plan for computer-assisted mining that would benefit the metal-nonmetal mining industry. This report details the team's accomplishments, specifically, the development of a model that identifies metal-nonmetal mining research needs that could be addressed by the application of automation technology. The report also provides a summary of automation needs and applications based on visits with mining company representatives. The status and future direction of this work is also presented.

Jan 1, 1994

By J. L. Hoffman, F. W. Wood, R. A. Beall, W. E. Anable

For melting and purifying reactive and refractory metals , two electronbeam furnaces have been constructed and operated on the principle of highpowered vacuum diodes . It was necessary to design the vacuum and electrical systems , mechanical features , and operating procedures to cope with dynamic conditions . Vacuums of 10-5 torr , tens of kilowatts of power at 5 to 10 kilovolts , and the evolution of impurities at thousands of liters per minute constitute a challenging combination . The furnaces have been used to melt either button specimens weighing several hundred grams or , by feeding material as a consumable electrode , small ingots weighing several kilograms . Hafnium is among the metals that can be purified . For example , hafnium starting material with Rhn 94B was softened to Rhn 70B after 2 hours of melting under a 25 - kw electron beam , and impurity levels were reduced as follows : Oxygen , from 700 to 350 ppm ; nitrogen , from 71 to 20 ppm ; hydrogen , from 6 to 1 ppm ; aluminum from 75 to < 20 ppm ; chromium , from 80 to < 10 ppm ; iron , from 100 to 40 ppm ; and silicon , from 40 to < 20 ppm .

Jan 1, 1963

By L. J. E. Hofer

This Bureau of Mines study, part of a broad program of research in air pollution related to minerals, was conducted to determine the nature and extent of the poisoning of catalysts when used to remove certain air pollutants from exhaust gases. The poisoning examined in this investigation occurs when leaded gasoline is used as a fuel for automotive engines. This research was conducted in cooperation with the Public Health Service. The smog in the Los Angeles area is attributed to the effect of radiant energy on the mixture of hydrocarbons and nitrogen oxides found in the atmosphere there. A large portion of the hydrocarbons is believed to originate in the exhaust gases of automobiles. To prevent the escape of these hydrocarbons into the atmosphere catalytic mufflers have been proposed. In principle, these are simple and nonmechanical, consisting of a vessel charged with a catalyst capable of destroying the exhaust hydrocarbons by catalyzing their oxidation. However, these catalysts are severely affected by the particulate matter, mainly in the form of lead sulfate (PbS04), lead oxysulfate (PbS04.Pb0), and Lead chlorobromide (Pb(Cl,Br)2), contained in the exhaust gas. Deposition of lead on the catalyst as PbS04, PbS04, PbS0, and Pb(Cl,Br)2 restricts catalytic activity. As a result,after 20,000 miles of operation the temperature necessary to achieve 50-percent conversion of isopentane in a mixture of 0.2 percent isopentane, 2 percent carbon monoxide and 4 percent oxygen, and the balance nitrogen at 10,000 hourly space velocity has risen from 400° C. to 500° C. even with a catalyst taken from the exit portion of the catalyst bed. The rest of the catalyst was more severely affected. Therefore, it would appear that operation for 20,000 miles is near the limit for a catalyst.

Jan 1, 1963

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By Philip C. Good

Preliminary studies showed that direct hydrolysis of H2SiF6 to SiO2 and HF at elevated temperatures was subject to many mechanical difficulties, and that corrosion of construction materials was a serious problem. Elimination of SiO2 from the HF product was generally poor. An alternative procedure, hydrolysis of lime-neutralized H2SiF6 by steam at 950° to 1,100° C, yielded a product very low in SiO2. Condensates containing up to 300 g/1 HF were prepared.

Jan 1, 1968