Search Documents

The Bureau of Mines, U.S. Department of the Interior, devised a flotation technique for upgrading chromite in chromium ores and gravity concentrates. The technique consisted of cationic flotation of chromite from a slime-free pulp acidified to pH 2.5 or lower using H2S04 modifier. Flotation results showed that ore containing serpentine as the primary gangue mineral was more amenable to concentration by this technique than ore containing the readily floatable olivine as the primary gangue mineral. Rougher flotation of a chromite ore containing abundant serpertine increased the grade form 19 to 41 percent Cra03 at a chromite recovery of 89.6 percent. Rougher flotation of ore containing abundant olivine upgraded the chromite from 23.4 to 29.6 percent Cr203 at a recovery of 89.4 percent. The technique was also applied to chromite gravity concentrates to further upgrade chromite and to reject silicates. Flotation of a gravity concentrate containing 40.9 percent Cr203 and 4.4 percent SiO2 recovered 90 percent of the chromite in cleaner products containing 44.9 percent Cr203 and 0.63 percent Si02. The combined recovery by gravity and flotation was 87 percent. An economic evaluation of this technique will be undertaken to deter-mine its feasibility for commercial use.

Jan 1, 1980

By H. J. Heinen

To maximize productivity through improved minerals processing technology, the U.S. Department of the Interior, Bureau of Mines, is investigating particle agglomeration techniques as a means of increasing the percolation rates of leach solutions in heap leaching of clayey gold-silver ores. Simulated heap leach experiments were conducted on 50-pound charges of ore that were contained in 5.5-inch-diameter columns, 5 feet in height. Results indicated that the percolation rate of cyanide leach solution could be enhanced markedly by mixing the ore with controlled amounts of lime, flocculants, and water, and then aging the mixture prior to the column leach step. Experimental results obtained on 20-mesh silver tailings and gold ore crushed to 3/8 inch and to 1 inch showed that it was possible to increase percolation rates as much as 100-fold without sacrificing silver-gold extraction. Larger scale tests conducted in 24-inch-diameter, 16-foot-high columns closely paralleled bench-scale results. By improving percolation leaching, these techniques have the potential of helping to solve environmental problems associated with tailings disposal as well as making an important economic impact on gold-silver recovery operations. Investigations are continuing to develop binders superior to lime for particle agglomeration pretreatment.

Jan 1, 1979

By Robert N. Roby

The Hornsilver lead-zinc property was examined by the Bureau in 1942 and again in 1944. A project was started on the property in April 1946 and completed in January 1947. Silver was first discovered in this district in 1883, and while complete production records are not available, it is known that a substantial tonnage of high-grade silver ore was shipped before 1887. All of the ore was mined from surface or near-surface workings. When the high-grade oxidized ore was exhausted, the district became inactive and remained so until the 1920's. In 1928 and 1929 some activity was shown in the district, but the Hornsilver mine was not reopened until November 1937. Between 1939 and 1946, the mine produced about 16,000 tons of ore of 531 ounces of gold, 283 ounces of silver, over a million pounds of load, and nerdy 2 million pounds of zinc. The property is now controlled by the Era Mining & Development Co., which has acquired the Last Chance and Ella groups of claims, in addition to the Hornsilver mine.

Jan 1, 1948

In 2005, a total of 2,063 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.1% of all mining operations. ? Bituminous mines comprised 92.6% (n=1,911) and anthracite mines 7.4% (n=152) of coal mining operations. ? Approximately 70% of all coal mines were located in three states: Kentucky (28.0%), West Virginia (21.8%), and Pennsylvania (20.6%).

Jan 1, 2008

In 2005, 14,666 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA).1 Almost half (48.5%) were sand and gravel mines, followed by stone mines (30.6%), coal mines (14.1%), nonmetal mines (5.0%), and metal mines (1.8%).

Jan 1, 2008

By P. H. Floyd

Laboratory test work has shown that the Germania ferberite-scheelite ore can be concentrated to an acceptable grade. A ferberite concentrate assaying 66.9 percent tungstic oxide was made, with a recovery of 75.4 percent. A second concentrate of ferberite and scheelite was made assaying 54.2 percent tungstic oxide. Final beneficiation of combined rougher gravity concentrates was accomplished by roasting, magnetic separation, sulfide flotation, and retabling, to give a final ferberite-scheelite concentrate of 66.2 percent tungstic oxide, with a 91.1-percent recovery. INTRODUCTION This presentation covers the results of laboratory beneficiation tests conducted on tungsten ore from the Germania Consolidated Mines, Inc., by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg. This mining property is near Fruitland, on the southern edge of the Spokane Indian Reservation, Stevens County, Wash. The Germania district produced tungsten concentrates before and after World War I; interest is being renewed in the district because of the metal shortage.

Jan 1, 1954

By Thomas J. Peters

During the 1982 Bureau of Mines study, 55 lode and 17 placer claims were held in the RARE II area. An estimated 150 lode claims and 50 placer claim, have been located in the study area; five were patented. There are no mineral leases. Gold has been produced from 8 lode mines and stream gravels have been worked for placer gold at 4 sites. Two suction dredges were active in stream gravels, but no significant gravel bars are identified. Identified mineral resources in the Weaver Bally area are gold and byproduct silver. The identified resources are at the Globe Mine, where approximately 33,000 tons of indicated marginal reserves (2,000 tons in the RARE II area, and 31,000 tons in the adjacent proposed Trinity Alps Wilderness) contain 0.45 oz gold per ton and probably 0.1 oz silver per ton. There are an additional 150,000 tons of inferred marginal reserves (35,000 tons in the RARE II area, and 115,000 tons in the adjacent proposed wilderness) averaging 0.38 oz gold per ton and probably 0.1 oz silver per ton. There is high potential for additional resources at the Globe Mine.

Jan 1, 1983

By D. Harrington

The placing of much, sometimes practically all, of the burden of the expense of mine accidents on the shoulders of the mine operator by compensation laws, and the fact that the problem of protecting the life end limb of workers is now by public opinion largely if not wholly passed to each industry to solve (and present-day thought strongly supports the justice of both of these propositions), are forcing industrial organizations into accident-prevention. Work. This policy is being adopted not alone to protect the companies; in addition, executives alert to their opportunities and obligations are taking part in this work personally to protect themselves. The functions of industrial executives in accident-prevention work are becoming numerous and complex. Executives who are logical in their reasoning, quickly see that before a company can constantly ask or expect the workers to heed safety suggestions, the company and its officials must "put their house in order" by laying down a concrete, definite safety program. For mines this includes primarily adoption of a to a logical mining method, the installation of safe miming equipment and practice the netting forth in definite form (preferably do a printed pamphlet) of the company's minimum safety requirements, and the organization of its operating officials into an accident-prevention body. After the company has its own affairs so arranged that it can go to its workers with "clear, hands" in promoting a safety program, the real work begins; and this is especially applicable in mining.

Jan 1, 1939

By J. P. Bennett

Based on previous Bureau of Mines research indicating that improved high-temperature properties could be achieved for periclase refractories through chemical additions, the Bureau investigated the properties of full-size bricks produced from chemically modified periclase refractory grains and the suitability of making such chemical additions to Mg(OH)2 slurries prior to production of the periclase grains. In full-size brick testing, strength values, both hot and cold, for the optimized bricks were superior to those for a commercial 98-wt-pct-MgO refractory. The best results were obtained for a natural magnesite with an adjusted CaO:Si02 (C:S) ratio of 3.0 and a 1.0-wt-pct addition of Zr02 and for a seawater periclase with an adjusted C:S ratio of 2.5 and a 0.5-wt-pct addition of Mn02. For samples produced from chemically modified Mg(OH)2 slurries, additions of both Mn02 and Zr02 and an increase in C:S ratios produced significant increases in hot flexural strength, similar to those resulting from chemical additions made to periclase grains. The most effective modifications were additions of Mn02 to brine-derived periclases having a C:S ratio adjusted to 3.0. These results on chemically modified magnesia refractories indicate that such material could potentially substitute for magnesiachrome refractories containing imported chromite.

Jan 1, 1984

By William J. Campbell

This Bureau of Mines report describes a study conducted to determine the relationship of mineral habit to particle size and shape characteristics for prismatic, acicular, fibrous, and asbestiform varieties of tremolite. Particle measurements were made with the petrographic microscope at X 1,250 and the scanning electron microscope at magnifications up to X 10,000. All of the varieties of tremolite, upon Wiley milling, produced a significant percentage of particles that meet the Federal regulatory criteria for counting as asbestos fibers. However, only the asbestiform variety gave milled particles that fell into a size range of >10 µm in length and <0.5 µm in width; some medical scientists consider this range significant for production of adverse health effects.

Jan 1, 1979

By G. L. Gates

The Bureau of Mines in cooperation with the City of Long Beach) Calif.) studied some physical factors effecting the deposition of barium sulfate scale in oil-well rotary pumps. Freshly formed barium sulfate was obtained by combining sulfate in sea water with barium from a barium chloride solution. The rate of scale deposition was measured quantitatively by weighing the pump impellers and diffusers. The results of the tests showed that coating the impellers with plastic significantly reduced the rate of barium sulfate deposition.

Jan 1, 1967

By Maurice Deul

A special short-term research project was initiated to develop plant design parameters for treating mine waters to yield an effluent acceptable for discharge into streams and a sludge amenable to effective and economic disposal. Neutralization was investigated to provide simple and direct treatment of ferruginous acid waters using lime; coarse limestone, and limestone followed by lime. Limestone treatment was accomplished using a small cement mixer as a simple reactor to provide abrasive agitation of limestone and mine water. Results from tests with nine mine waters encompassing a wide range of iron and acid concentrations showed that coarse limestone, one of the cheapest neutralizing agents known, is potentially useful for treating mine water discharges. However, process variables must be defined more completely before the practical applications and limitations of the process can be fully established. In all the tests a pH of >7.2 was obtained ultimately with limestone. Reaction time to reduce the iron content below 7 ppm in the water was dependent on the original ferrous iron concentration. For waters with high ferrous iron content, treatment with limestone followed by lime rapidly produced an acceptable treated water, Sludges with good settling and handling characteristics resulted when limestone was used for neutralization either alone or with subsequent treatment. Reaction rates are expressed graphically as pH change and iron depletion curves; characteristic solids settling curves are shown. The temperature dependency of ferrous iron oxidation was verified.

Jan 1, 1967

By Thomas Fraser, J. D. Davis

"INTRODUCTION Preliminary tests of the Oyon coal constituted part of a wartime exploratory and development program in which many agencies participated. The general objective was to find new and adequate source of fuel and other raw materials for greatly expanded industry.The Oyon coal field, known for at least a hundred years to the mining people of Peru, offers a possible source of high-grade process fuel for the growing metallurgical industries of South America and the Pacific coast. Santolalla 4/ reports that low-volatile coal from this region was used in local smelting operations as early as 1850. It has been mined in very small quanti¬ties for many years and used in neighboring mining camps and villages. Small quantities are regularly used at Oroya for the manufacture of carbide, and in recent years small-scale coking operations in specially designed ovens in the region have demonstrated that these coals will make dense coke.During this long period of desultory operations many small openings have been made scattered over a wide area in this general region, indicating very extensive occurrence of the coal measures, although systematic exploration work has not been undertaken. However, current development work of the Banco Minero del Peru has opened up several substantially parallel highly inclined or vertical beds of workable thickness and has followed these deposits to sufficient lateral extent to prove fairly well the existence of substantial reserves on this property."

Mar 1, 1948

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By E. M. Tignor

A research program to aid development of improved methods for increased production of petroleum from partly depleted reservoirs is a vital part of the Bureau of Mines effort to effect true conservation of that mineral resource. This report presents results of an investigation to identify the clay minerals within some Appalachian petroleum-reservoir sands, the effect of clay content on the fluid-flow behavior of those sands, and the use of brines in water-flooding operations. Permeability measurements using kerosine, calcium chloride brine, simulated oilfield brine, potassium chloride brine, sodium chloride brine, and distilled water were made on reservoir-rock cores. Clay fractions were separated from sand grains of disaggregated portions of each core sample, and the clay minerals were identified by the differential thermal analysis method. Relations of the permeability to various fluids were developed.

Jan 1, 1957

By John B. Gayle

During studies of the various methods for determining and specifying the factors that indicate whether a particular coke is better or worse than other cokes for metallurgical uses, questions arose as to the precision of screen-analysis tests on coke. Although the usual index of precision, the standard deviation of the test result, gives a measure of the precision of these data, the experimental determination of the standard deviation for a particular set of conditions requires tests on a large number of duplicate samples. Because this procedure necessaily involves a great deal of labor, an equation for predicting standard deviations from theoretical considerations has been developed. Results predicted with this equation agree satisfactorily with the experimental values and are applicable to tests on coal, coke, gravel, and other bulk materials.

Jan 1, 1952

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By Curtis D. Edgerton

Miami Oölite limestone is the only significant construction mineral in southeastern Florida. Its source area coincides with that of rapid urban expansion. Two-thirds of the existing resource is already unavailable because of development. Land-use conflicts place future availability of limestone in jeopardy. However, a sufficient limestone resource to meet demand for many years is present if its extraction is not restricted. Adverse environmental effects of quarrying Miami Oölite are not severe; land values often increase following quarrying. Future availability depends upon--(l) achieving uniformity of Federal, State, county, and municipality statutory requirements governing quarry operations; (2) setting aside specific land areas for future quarrying; and (3) cooperative planning to provide for land utilization upon completion of quarrying.

Jan 1, 1974

By Thomas M. Barczak

This U.S. Bureau of Mines report is intended to assist coal mine operators in the selection of longwall supports by providing advanced guidelines for performance testing and standardized test documentation to facilitate support comparisons. These advanced guidelines culminate in a series of proposed tests to evaluate (1) support resistance characteristics, (2) stiffness characteristics, (3) leg mechanics, (4) stability, (5) load transfer mechanics, and (6) structural integrity. The Bureau has conducted extensive studies on shield mechanics to identify boundary conditions that induce loading in support components, which is often not included in current testing techniques. This report discusses influential parameters that affect support behavior and provides insight into how components are loaded and what conditions produce the most severe loading. Testing philosophies and techniques in both active and static frames are discussed. Proper methods for determining support resistance are described and instrumentation requirements for advanced performance testing are provided.

Jan 1, 1989