Search Documents

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Southern Experiment Station of the U.S. Bureau of Mines, cooperating with the University of Alabama and Alabama coal producers, has made a series of investigations of the washability of coal from commercially important bens of Alabama. The results of 13 investigations pertaining to the Mary Lee, Clark, Black Creek, Jefferson, Pratt, Corona, Carter Brookwood, Blue Creek, Thompson, and Woodstock beds have been published. 4/ This report, the fourteenth of the series, deals with run-of-mine coal from the Henry Ellen bed at the Acmar No. 5 mine of the Alabama Fuel & Iron Co.The Acmar mine is 1/2 mile west of Acmar, Saint Clair County, in the northern part of the Cahaba field. Present production at the mine is about 800 tons per day, all of which, accept the lump coal, is treated in jigs. The washability data were obtained by means of screen-sizing and float-and-sink tests. There are included, also, tests showing the extent of liberation of impurities by recrushing the coarser sizes of coal from the top bench and tests showing the flakiness in selected sizes.SAMPLING AT THE MINEThe Henry Ellen bed at Acmar consists of two benches separated by a shale parting. At the point of sampling the top bench was 6 feet 3 inches thick and contained a 1-inch and a 1 1/2-inch band of bone. The bottom bench was 5 feet thick and was separated from the top bench by 20 inches of shale. In taking the samples for the washability study the working face was squared up, and a representative 2-ton section was out from each bench. The shale parting was discarded, according to usual mining practice."

Nov 1, 1936

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

By Elizabeth G. Baglin

Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black mud prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simu-lated Bayer digestion of Jamaican bauxite with added ferrous sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly washed prior to electrodewatering to remove dissolved ions and decrease mud conductivities.

Jan 1, 1988

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By W. P. Diamond

The direct method test was developed for general mine safety applications by the U.S. Bureau of Mines in the early 1970's to measure the gas content of coal samples obtained from the relatively shallow depths of eastern U.S. coal mines. Over time, applications for gas content data evolved which required increasingly accurate desorption values. It became evident that some of the inherent weaknesses in the original direct method test could best be addressed by abandoning the water displacement based desorbed gas volume measurements. The ideal gas law based modified direct method (MDM) and associated desorbed gas volume measurement apparatus was developed to provide the most accurate desorption values possible for rock samples obtained from any gas-bearing strata. The MDM has a number of significant advantages, including: (1) increased accuracy, especially for low gas content samples, (2) a test apparatus with an integral sampling port to facilitate the collection of uncontaminated gas samples, (3) an inherent head space effect correction in the periodic MDM desorbed gas volume calculations, (4) measurement of positive and negative desorbed gas volumes, (5) elimination of differential gas solubility effects as a source of error inherent in the water displacement methods, and (6) a compact and rugged test apparatus that along with the elimination of the ?glassware? required for the water displacement methods, facilitates its use in the field.

Jan 1, 2008

By John R. Coulson

Each State and the Federal Government was surveyed for existing certification requirements, the industry yes surveyed for the needs for training blasters, and the training that was available. Recommendations for training and certification for blasters were made.

Jan 1, 1980

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By Robert B. Fulton

Summary of data and estimates for 52 fluorspar properties in the following 13 foreign countries: Mexico Thailand China (PRC) Morocco Tunisia Italy Spain South Africa France United Kingdom Kenya Namibia Federal Republic of Germany Data includes deposit type, resource tonnage and grades, mining and beneficiation methods, annual production, fluorspar products and by-products, manpower requirements, capital and operating cost estimates. For operating properties, engineering and cost data have been developed for present and anticipated levels of production. Hypothetical operations have been assumed for undeveloped deposits.

Jan 1, 1984

The Aluminum Co. of America raised its 99.5 percent unalloyed aluminum ingot selling price in March by 34 to 514 per pound. Other producers, including Kaiser Aluminum and Chemical Corp. , Anaconda Aluminum Co. , and Reynolds Metals Co., followed Alcoa's lead, raising their quotes to 51$. In late March, domestic merchants quoted ingot at levels ranging between 49.56 and 50.50 per pound. BISMUTH: Several domes tic dealers lowered their bismuth prices in recent weeks by 50t-606 to within a range of $5.60-$5.75 per pound; producers continue to hold published prices at $7.50.

Jan 1, 1977

The U.S. Code of Federal Regulations (Title 30) requires that a methane monitor be placed on every mining machine to continuously observe and record methane levels at the face. The monitor must provide a warning whenever methane levels are 1.0 percent or higher. An effective monitoring system will indicate a methane concentration of 1.0 percent on the mining machine before methane levels at the mining face reach 5.0 percent. Where the methane monitor is located on the mining machine is one of the most important factors that determines how effectively face methane levels can be predicted. Any change in the sampling location will result in a change in measured methane concentration. To protect the methanometer, it is usually located on the cutting boom at least 1 to 1.8 m (3 to 6 ft) outby the front cutting bits. A face ventilation system using blowing tubing was simulated in a full-scale test facility. Methane released from the face area was monitored at multiple locations on a model mining machine as well as locations near the face. Based on the relationship between concentrations measured on the machine and at the face, criteria were developed for selecting the best machine locations for monitoring methane. Recommendations are given for revising methane action levels for alternative sampling locations.

By Robert T. Davis

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to the coal-mining industry's underground and open-pit mines that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1964

By Janine Pierce, Robert Larson, Christine Raasch

The vibration and impact environment for crew members on locomotives has been investigated in a series of studies conducted by Exponent Failure Analysis Associates (Exponent) beginning in 1990. Locomotive cab vibration and impact levels were measured on a variety of locomotive models operating over many different track sections across the Union Pacific, Burlington Northern Santa Fe, CSX, Norfolk Southern, and CONRAIL systems. The comfort and health implications of exposure to the measured locomotive vibration levels were evaluated by comparison with the human vibration exposure boundaries given in the International Standards Organization (ISO) standard 2631-1:1997, the British Standard 6841:1987, European Union (EU) Directive 2002/44/EC, measurements made by Exponent on various commercial and recreational vehicles, and vibration exposure measurement data found in the literature. Methods Initially, vibration levels experienced by locomotive crews were measured and recorded at incremental speeds covering the range of normal train operation. In 2003, a method of measuring the vibration exposure continuously by means of a digital recorder was developed, allowing the vibration level over the entire run or crew shift to be analyzed. For each seating location measured, acceleration was recorded on the seat surface beneath the ischial tuberosities (pelvis) of the seated crew member and on the cab floor directly under the seat. At each of the locations, triaxial accelerometers were used to measure the vibration along the longitudinal, lateral, and vertical axes. Since the vibration environment varies throughout the route, and locomotive vibration levels have been found to be primarily speed dependent, a speed sensor was used to continuously measure the speed of the train. To evaluate the recorded vibrations levels, the data was divided into two-minute segments, which were each processed per the 1997 ISO standard for weighted RMS vibration levels and Vibration Dose Values (VDV). Additionally, PSDs and 1/3 Octave RMS values were calculated to determine the frequency content of the vibration. For each two-minute segment, the average speed of the locomotive was calculated to allow for correlation with the recorded vibration exposure values. The resulting exposure values for the entire run were calculated by combining the data from all of the two-minute segments. Since introducing the continuous method of recording acceleration, 23 seating locations have been recorded on 11 locomotives traveling 11 different routes across various parts of the United States. One of the routes was a shift of ‘yard work’, traveling back and forth in a rail yard coupling train cars together. Results A guide to interpreting weighted acceleration values with respect to health is given in Annex B of the 1997 ISO standard. A health guidance caution zone is defined to indicate the

Jan 6, 2006

By Lu Li, Sara E. Wilson

Occupational exposure to whole body vibration has long been associated with increased incidence of low back pain and low back injuries1. A number of studies have investigated transmissibility of seat pan vibration 5, 6. While transmissibility has been well researched, the mechanism by which vibration may induce injury has not been thoroughly studied. Winter et al. identified increased reflex response delay after vibration exposure and speculated that muscular fatigue may be the cause of this increase9. However, a mechanism has yet to be demonstrated completely. A potential mechanism that may explain the increased risk is neuromotor habituation. Muscle spindle organs have been shown in the extremities to be sensitive to muscle and tendon vibration. Rapid length changes in muscle have been shown to result in kinesthetic illusions as the regular firing of the muscle spindles is interpreted as muscle lengthening4, 7. These illusions have also been demonstrated in the paraspinal musculature2. With removal of vibration, research in the extremities has demonstrated increased positioning errors, probably due to neuromotor habituation8. In this research, it has been hypothesized that neuromotor habituation after exposure to occupational vibration will increase positioning errors. It is further hypothesized that these errors can be shown to be linked to increased reflex response time. Such increased reflex response time could, in turn, decrease spinal stability and increase low back injury risk. Methods Both positioning error and sudden load response were measured before and after exposure to 20 minutes of 5 Hz, 0.223 m/s2 RMS seat pan vibration. Subjects were asked to sit on an unpadded seat without a backrest. Throughout the whole body vibration period, subjects were instructed to put their hands on a stable hand rest and feet on an adjustable stable footrest. The subjects were instructed to assume a comfortable and relax sitting posture for the duration of the exposure. Positioning error was measured using an active-active reposition sense protocol. Electromagnetic markers (Motionstar, Ascension Tech, Burlington, VT) were used to track trunk motion. With markers attached to the skin at the T10 vertebra, the S1 vertebra and manubrium, trunk flexion (the angle from vertical of the line connecting T10 and S1) and lumbar curvature (the difference in inclination of the T10 and S1 markers) were tracked. In the reposition sense protocol, subjects were asked to maintain an upright trunk flexion and to rotate their pelvis and lumbar curvature to assume a target lumbar curvature. In the protocol subjects completed training trials, where they were asked to match their lumbar curvature using a visual display, and assessment trials, where they were asked to reproduce the lumbar curvature from memory. After two initial training trials, training trials and assessment trials were alternated for a total of 3 assessment trials. Reposition error was defined as the absolute difference between the target lumbar curvature and the lumbar curvature the subject assumed during the assessment trials.

Jan 6, 2006

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By Claud Johnson, G. Roger Miller, Kristine M. Krajnak, Stacey Waugh, Oliver Wirth

Workers exposed to vibrating hand tools are at risk of developing symptoms such as cold-induced vasospasms, loss of tactile sensitivity, and loss of grip strength in the fingers and hands. These symptoms are known collectively as vibration white finger (VWF) or hand-arm vibration syndrome (HAVS). Symptoms of VWF or HAVS are in part due to repeated and prolonged peripheral vasoconstriction[1, 2]. The reduction in blood flow that occurs with vasoconstriction can result in oxygen deprivation (hypoxia) in soft tissues, such as nerves and muscle, and lead to functional and structural changes in these tissues. The present study examined muscle tissue to determine if vibration-induced changes in transcript levels and protein concentrations result in enhanced vasoconstriction and hypoxia. Manual dexterity was also assessed intermittently to determine if vibration-induced changes in cellular factors are accompanied by performance deficits. Methods An animal model was developed to study the biological and functional changes that occur in response to repeated segmental vibration exposures. In this model, the right paw of intact rats was exposed to a platform vibrated at a frequency 250 Hz and amplitude of 49 m/s2 to simulate the vibration characteristics of hand-held grinders. Three groups of 8 rats each were studied: a vibration-exposed group, an exposure-control group, and a cage-control group. Exposure sessions, with or without vibration, were conducted 4 hr/day, 5 days/week for 5 weeks. Manual dexterity was assessed intermittently during the 5-week exposure period with the Montoya stair-case test[3], which quantifies the rat’s ability to reach for, grasp, and retrieve small food pellets placed below the rat on different levels or steps. Following the 5-week exposure period, the flexor muscles of the right forelimb were collected for analysis of gene expression, protein concentrations, and immunohistochemistry. Results Vibration-exposure resulted in an approximate 2-fold increase in the expression of a2C and a1D receptor transcripts in flexor muscles (Figure 1). These receptors mediate norepinephrine-induced vasoconstriction in smaller arteries. Vibration-exposure also resulted in an approximate 2-fold increase in hypoxia-induced factor-1a (HIF-1a), a transcription factor that is expressed in response to tissue hypoxia. Western analyses demonstrated that restraint caused a decrease in a1-receptor protein concentrations in the flexor, but vibration-exposure prevented the restraint-induced reduction (Figure 2). Immunohistochemistry performed on flexor muscles (not shown) demonstrated that a1 receptors are primarily located in arteries; maintained levels of these receptors could contribute to prolonged vasoconstriction following repeated vibration exposure. The staircase test showed some performance improvement, or a training effect, in manual dexterity for the control groups but not the vibration-exposed group (Figure 3).

Jan 6, 2006

By Chi-Mun Song, Seok-Hyun Choi, Seok-In Hong, Han-Kee Jang

Accurate measurement and evaluation of hand-transmitted vibration from a power tool is an important issue for tool manufacturers, because they are obliged to develop low-hazard power tools for workers. The International Standard ISO 5349(1) dictates a systematic procedure for the measurement and evaluation of hand-transmitted vibration. However, the uncertainty in this measurement is too large for manufacturers to apply such data to the design and modification of power tools. There can be several sources of this uncertainty in such measurements; e.g., operator-dependent, power tool-dependent, and operational conditions (see Table 1). For a manufacturer to characterize the exposure of a power tool’s use to a given level of vibration, the relationship between these uncertainty factors and the measured vibration must be elucidated. In this study, we investigated the effect of several factors on the uncertainty in measurements. [ ] Methods In this study, some of the factors in Table 1 were selected for examination, and their effect on the measured variation was quantitatively investigated. Three tools from the same manufacturer were sampled at random in our experiments, and each of five of the same type of insert (disks or tips) was installed into each tool. Although each of the tools and inserts were of the same design and were made by the same production process, they differed from one to another, which can be a source of the variation in the measured vibration. Three human subjects participated in our experiments, which were carried out as stated in ISO 5349. The subjects were asked to maintain their posture, and the applied force was kept as constant as possible. The applied force was monitored using an indirect method, where vibration energy was displayed in real time during the experiment using a three-axis accelerometer attached to the work piece at a specified point. The appropriate range of the applied force was predetermined to cover the range of real work operations. The engineering tolerance between the inner diameter of a grit disk and the outer diameter of the tool shaft leads to an eccentricity of the mass at the center of the disk. The degree of eccentricity varies with installation, and this is another source of uncertainty. In our study, the effect of this eccentricity was investigated by carrying out repeated assembly and disassembly of an insert.

Jan 6, 2006

By Alex C. Smith, Michael J. Sapko

A series of explosive detonation experiments was conducted in NIOSH’s Bruceton and Lake Lynn Experimental Mines to evaluate low level (<6 psig) detonation wave propagation behavior in single and multiple entry configurations. Entry cross-sectional area varied from 5 to140 m2 and explosive weights of Pentolite ranged from 0.24 to 2.4 kg. Behavior of the detonation wave was evaluated through recording of the pressure as a function of time and distance from the explosive detonation in single and multiple entry interconnecting tunnels. Peak pressure from detonation of an explosive in an underground mine maintains magnitude for a greater distance than is the case on the surface and is shown to follow the simple scaling rela-tionship P = 702.8(W/Vt)0.514(0.65)n, where P is the peak detonation pressure in kPa, W is the weight of the explosive charge in kg, Vt is the total volume in m3, and n is the number of splits, n = 0, 1, 2, …n. The total energy, or impulse, I, generated by these detonations can be expressed as I = 1.34(W/A)0.64n, where W is the weight of the explosive charge in kg, A is the area of the main tunnel in m2, and n is the number of side en-tries, n = 0, 1, 2, …n.

Commodities statistics and otter information are available through the following t et systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine&apos;s telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By R. V. Ramani, R. Bhaskar

"The results .of an experimental and theoretical research study into the spatial and .temporal behavior of dust in mine airways is summarized in the paper. Experiments were performed in mine airways under both controlled and .normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using Real-time Aerosol Monitors (RAM-1) to determine the dispersion coefficient in a mine airway. On the theoretical front, a convection diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion.In this paper, comparative analyses of results of the controlled experiments with the predictions of the mathematical model are presented. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion are examined in light of the experimental observations.The experimental data from controlled experiments compared more favorably with model predicted results for similar conditions as opposed to the ·comparative analysis results for in-mine experiments. Specifically, the model· predictions for an 800-meter stretch of a mine airway reveal some significant differences from the behavior noticed in the mine. The deposition was lower than that predicted by the model. Consequently, concentrations were higher than those predicted by the model. The implications of these and other findings for further investigations are discussed in the paper."

Aug 31, 1989