Search Documents

By William R. Roy

Seven coal-related waste samples (mining, cleaning, and gasification) were characterized chemically and mineralogically. Laboratory extracts of each sample, using a variety of different extraction methods, were used in both acute and chronic bioassays. A coal slurry sample (coarse fraction) and two coal cleaning refuse samples were chemically and mineralogically similar, and generated acidic water-waste systems, both in the laboratory and in the field. Acidic laboratory extracts and field samples of acid mine drainage in the area where the solid samples were collected, tended to be in equilibrium with some type of CaSO4 phase and with maghemite. The chemical composition of the extracts was sensitive to the method used to generate the extracts, but generally had the same prevalent chemical character as the field samples. The acidic wastes contain appreciable quantities of soluble Al, Mn, Ni, SO4, and Zn as indicated by both laboratory extraction and field data. Long-term extractions suggest that some constituents (Al, Fe, SO4) continued to be released by the acidic wastes after 22 weeks with no apparent associated change in pH. Two mine spoil samples, essentially shale, tended to generate water-waste systems that were neutral in pH and consequently released lower quantities tit potential pollutants than the acid wastes. The gasification residue was compositionally similar to coal-fired power plant slag and fly ash and generated moderately alkaline extracts with low concentration of soluble potentially toxic constituents. All of the solid wastes contained a variety of organic compounds, many of which are on the EPA Priority Pollutant List. However, these compounds were essentially insoluble in aqueous media. Each extract was tested for acute toxicity with tour species of freshwater aquatic organisms; green sunfish (Lepomis cyanellus), fathead minnow (Pimephales promelas), a crustacean (Daphnia magna), and a snail (Physa anatina). The extracts of the two mine spoil samples and of the gasification residue were not toxic to any of the organisms while the extracts from the acidic refuse and slurry samples were acutely toxic to all of the organisms. For all cases, pH was significantly correlated to mortality while Al, Fe, Mn, Ni, and Zn were significantly correlated to mortality in specific instances. Data from 96-hour LC-50 determinations showed that dilutions up to 1:1000 were necessary to eliminate mortality. The most toxic extracts were those with the lowest pH which necessitated the largest amounts of dilution to eliminate mortality. Chronic bioassays with the same test organisms were investigated with leachate samples from a relatively unweathered refuse sample and an older, more weathered refuse sample. The unweathered refuse sample generated a leachate that was acutely toxic while the leachate from the weathered refuse sample was not acutely toxic. No detrimental chronic effects were noted in organisms exposed to dilutions of the non-toxic leachate while low concentrations of the acutely toxic leachate produced lower hatchability for the Lepomis cyanellus and Pimephales promelas eggs, increased mortality with chronic exposure for Lepomis cyanellus, Daphnia, Physa, and reduced weight gain for Physa. Dilutions of a toxic, high-Fe leachate resulted in the precipitation of ferric hydroxide that was implicated as the major causative factor accounting for the physical and physiological toxic effects exhibited by all of the test organisms in these acutely sublethal concentrations. The toxicity of this leachate demonstrates the potential effects that these types of wastes can have on the aquatic ecosystem if they enter a receiving water in a natural setting.

Jan 1, 1984

By D. Randolph Berry

The U.S. Bureau of Mines awarded a contract to Foster-Miller Associates, Inc. (FMA) to provide recommendations on the safest, most practical methods for complying with new regulations requiring that all underground coal miners have a self-contained, self-rescuer (SCSR) -a device capable of supplying, in an emergency, 1 hr of self-contained oxygen (no breathing of mine air). This report develops information and recommendations which could be used during the early stages of nationwide compliance, especially in the areas of inspection, testing, and underground storage of SCSRs. Volume I contains an Executive Summary, Introduction, Definitions, Recommended Guidelines for District Managers and Mine Operators, and a Storage Plan Checklist and Sample Form.

Jan 1, 1981

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By Lloyd Williams

1. The investigation shows that the Pewee, Big Mary, and Windrock are the most important beds in Anderson County. About 73 percent of the known recoverable reserves of coal in the county are in these beds, and from them comes 94 percent of the production. The remaining reserves tabulated in this report are in the Joyner, Jellico, Coal Creek, and Poplar Creek beds, and 6 percent of the county production comes from these beds. No production is being reported at present from the Jellico bed, although it was mined years ago. 2. Known measured and indicated reserves in all beds, bared on a minimum thickness of 1/4 inches and on 1,800 short tons put acre-foot of coal in place, are estimated to be 170 million torts as of January 1, 1953 Of this total, 155 million tons is in beds 2S inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to they total estimated reserves.

Jan 1, 1955

By Harry H. Ku

In December 1975, a report entitled "An Evaluation of the Accuracy of the Coal Mine Dust Sampling Program Administered by the Department of Interior" [1] was prepared by the Analytical Chemistry Division of the National Bureau of Standards (NBS), in response to a request by Senator Harrison A. Williams. Chairman, Committee on Labor and Public Welfare. The report attempted to evaluate the adequacy of (1) the personal sampler unit used to measure the coal dust concentration in the mines, (2) the procedures used by the Department of Interior (DOI) to analyze the dust samples obtained from mine operators, and (3) any recent studies made by the Department or private industry concerning the coal dust sampling equipment. Recommendations in the report of NBS included continued research efforts by the appropriate organization to correct the personal sampler deficiencies and to consider the use of area or stationary samplers as a supplement to the personal samplers. Concurrent with the NBS report cited above, the General Accounting Office (GAO) also issued a report in December, 1975 [2], suggesting that improvements are still needed in coal mine dust sampling programs and procedures relating to penalty assessments and collections. Among recommendations made by GAO, the following paragraph specifically called for actions by the agencies involved:

Jan 1, 1979

By Raymond B. Ladoo

"The talc and soapstone deposits of Vermont have been worked more or less continuously for nearly 100 years, but all of the early efforts seem to have been directed toward the production of slabs for foot warmer, and other similar uses. Altho soapstone of good quality occurs at several places, much of the material first utilized was really talc and was not massive enough to be cut successfully. The grinding of talc in Vermont seems to have commenced in about 1902 and has shown continuous growth since that time. Statistics compiled by the Geological Survey in Mineral Resources of the ,United States show that the production of talc in Vermont has increased, from 8,978 short tons valued at $65,525 in 1905 to 93,960 short tons valued at $625,150 in 1917. Until 1917, New York was the leading producer in both tonnage and value with Vermont second, but in 1917, Vermont took the lead in tonnage produced, although not in value, with a production of over 47% of the total tonnage produced in the United States and over 35% of the world's pro-duction. This increase in production will probably be continued, though possibly at decreased rate, for the reserves of talc In Vermont are large.Active talc mines and mills in Vermont are found in four districts: Chester, Windsor County; Rochester, Windsor County; Waterbury, Washington County; and Johnson, Lamoille County, These mines and mills are distributed as shown in the following table:While there are a great many other known deposits of talc and soapstone in Vermont, some of which have been worked, those listed above are the only ones which have survived and are producing on a commercial basis. The closing down of many mines and quarries, for example, those at Perkinsville, Stockbridge, Reading, Cavendish, and Athens, has been attributed to several causes. Of these causes the most important seem to be exhaustion of the deposit, poor grade, long haul to the railroad, poor management due to lack of knowledge of mining methods and failure to consider talc mining strictly as a business proposition. The companies which are now operating with greatest apparent success are those which have realized the present and future possibilities of their industry, and have invested sufficient capital in both equipment and personnel to establish their companies on a firm business basis."

Sep 1, 1919

By H. N. Dunning

A comprehensive research program designed to aid development of new and improved methods for more complete production of petroleum from partly depleted reservoirs is being conducted at the Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla. Water flooding has accounted for much of the petroleum produced by secondary-recovery methods; however, a considerable portion of the crude oil commonly remains in place after water flooding has been terminated. In recent years the possibility of increasing the efficiency of water flooding by using surface-active additives has received wide attention. In general, the results of laboratory research have shown that use of detergents as water-flooding additives will reduce the residual petroleum in porous media (1).3/ Some less extensive field tests have supported this conclusion but have not been entirely conclusive (2). Later studies (3, 4) have given conflicting evidence as to the relative worth of detergent additives for water floods in water-wet (hydrophilic) or oil-wet (hydrophobic or lipophilic) reservoir materials. The results of these studies emphasize the need for a more complete understanding of the fundamental principles involved in displacing petroleum from reservoir surfaces by injected fluids. Accordingly, a comprehensive research program was initiated to investigate the practical and fundamental aspects of detergency in petroleum production.

Jan 1, 1953

By Lito C. Mejia

Diesel-powered equipment operating in a gassy underground mine could conceivably ingest a methane-air mixture from the mine atmosphere that could cause the diesel engine to overspeed, or exceed its rated speed. Engine overspeed, particularly if extreme (engine runaway), could result in personal injury, a possible mine explosion, and/or catastrophic engine failure. In this report, the Bureau of Mines reviews the literature on the potential hazards of methane-induced diesel engine overspeed. Also included are the Bureau's findings from consultations with representatives of the diesel engine industry to determine the specific engine behavior that could he expected under the overspeed condition. The report summarizes data on mine accidents involving methane, discusses results of tests on the compression ignition of methane in diesel engines, and examines fuel governors and intake-air-cutoff devices, two kinds of devices used to prevent overspeed. Analysis of the information gathered suggests that the conditions necessary to cause a diesel engine to overspeed uncontrollably are not likely to occur, particularly if the engine is equipped with flame-proofing devices. The available literature and lack of actual overspeed case histories suggest that the safety devices currently in use are sufficient to prevent diesel engine overspeed.

Jan 1, 1984

By Charles E. Whieldon, C. I. Pierce

Data on the oilfields in Mahoning , Columbiana , Carroll , Jefferson , and Harrison Counties , Ohio , were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary - recovery operations in the area . General geology , oil production , oil - productive acreage , core data , reservoir calculations by townships , and miscellaneous data and reference material are presented .

Jan 1, 1965

By Robert C. Johnson

Water-swelling fluormicas and fluormontmorillonoids were synthesized and described. They were found predominantly in the system Mg0 - MgF2 - Si02, with varying amounts of Li+ or Na+, Some water-swelling synthetic minerals were prepared with only strontium or lead in the twelvefold position, Water- swelling compounds containing either K+ or Ba+ were not found. The synthesized water-swelling products were shown by electron microscopy, X-ray diffraction, and chemical analysis to be typically two-silica-layer, platy compounds, Except for the complete substitution of fluoride for hydroxyl, the compounds were similar to the natural micas or montmorillonites. The stability and properties of the compounds were further established by electrodialysis, by differential thermal analysis, and by anion and cation exchange methods. Fluoride in the interlayer positions was nonexchangeable except through decomposition of the product. Exchanging the sodium or the lithium of the synthetic fluormicas or fluormontmorillonoids with potassium ion, particularly those derived from KOH provided a product from which a completely inorganic paper of extraordinary flexibility was fabricated. This paper had excellent mechanical and electrical properties except for water adsorption and a high power factor. Neither of these problems was solved during this investigation. However, papers with dielectric strength from 1,500 to 5,000 volts per mil were readily fabricated, particularly from the lithium containing fluormicas or fluormontmorill onoids.

Jan 1, 1963

By S. H. Lorain

This paper is one of a series on mining methods and costs being published by the U. S. Bureau of Mines. The operations of the Quartz Hill Mining Co., near Dewey, Mont., afford an interesting example of the cost of mining small bodies of direct shipping ore; they also illustrate the effect of the unavoidable periods of unusually high exploration and development costs in this type of mining upon the cost per ton of producing ore. The importance of skilled geological guidance and the necessity of avoiding unnecessary overhead and capital expense at small mines are shown. Operating conditions at Quartz Hill are typical of those in many other mining districts of southwestern Montana. It is believed that the costs presented here may be of value in the preliminary estimation of costs to be expected by conservative operators under similar conditions elsewhere. The information contained in this paper was obtained during a visit to the Quartz Hill mine in August 1936.

Jan 1, 1937

By B. J. Moore

This publication contains routine analyses and related source data for 547 natural gas samples from 22 States and three foreign countries. Of this total, 340 samples were collected during calendar year 1967. The remaining 207 analyses are of samples collected during previous years, but releases granting, permission to publish the results were not received until 1967. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. The Bureau of Mines has conducted this survey in the United States since 1917, and in 1965 it was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 516.4 Nine previous publications have been made to present results of 7,618 gas analyses made by the Bureau of Mines Helium Activity prior to 1967. The first three, Bulletins 486,5 576,6 and 6177 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other six

Jan 1, 1968

By Paul M. Ambrose

Overall the domestic abrasives industry had one of its best years in 1965. Production and value of all commodities increased over that of 1964 which also was a good year. Production of tripoli that was down in the previous year rebounded and production from two new mines was reported. Plant capacities for production of silicon carbide and fused crude aluminum oxide and production from plants in the United States and Canada increased, but demand was high and yearend stocks were less than at the end of 1964. Foreign Trade.-Increases in value of most imports of abrasive materials in 1965 were offset by a decrease in the value of imported industrial diamond. Production of fused aluminum oxide and silicon car-bide in the United States and Canada and imports of these commodities into the United States increased, but combined exports of finished grain of these materials was virtually unchanged from the previous year.

Jan 1, 1966

By Richard J. Mainiero, Michael J. Sapko, James H. Rowland III, Marcia L. Harris

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 @ 10-38 cm6 molecules-2 sec-1 for the rate equation -½d [NO]/dt = K @ [NO]2 @ [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).

By J. B. Gayle

Since the turn of this century, there has been increasing interest in the application of flotation processes to the beneficiation of finely divided minerals of various types, This is reflected by the large numbers of papers dealing with various aspects of this problem published annually both in this country and abroad. For the most part, such papers fall into one of three categories: 1. Those concerned with achieving, by various chemical and/or physical means, a set of conditions under which certain particles become potentially floatable while others do not. 2. Descriptive studies of plants and pilot plants effecting separations between such particles. 3. Studies of the effects of certain design and operating variables on the rates and efficiencies with which such separations can be effected.

Jan 1, 1959

By Louis H. Berkelhamer

"INTRODUCTION The method of differential thermal analysis suggested by Le Chatelier (1)1 in 1887 has recently emerged as an outstanding means of studying the constitution of various substances, particularly clays, soils, and miscellaneous hydrous materials (2). The literature ably discusses the applications and results obtained but has paid too little attention to specific details of construction of the apparatus. Knowledge of the apparatus is of importance to the experienced research man as is extremely useful to the novice v ho ventures into this field of analysis. Further, it is generally acknowledged that the variations in design and conditions of operation are one of the essential causes for differences in characteristic temperatures as reported by various investigators. A step forward in the elimination of such differences is the publication of the details of construction and operation of a simple and inexpensive apparatus that has proved useful at the southern Experiment station of the Bureau of Mines, where it was used in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jul 1, 1944

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By A. C. Fieldner, G. W. Jones

Tests were made at the Government Fuel Yard , operated at Washington , D. C. by the Bureau of Mines , Department of the Interior , in order to determine and improve the adjustment of the carburetors on the trucks used for transporting coal from the Fuel Yard to the different Government buildings in Washington . The tests were made possible through the hearty cooperation of G , S. Pope , engineer in charge of the Fuel Yard . Joseph Burrows and A. E. Foote of the garage department assisted during all the tests and supplied information on the mileage obtained by the trucks for the months preceding and succeding the time the tests were made . The Mack trucks used range in capacity from 2-1/2 to 7-1/2 ttoonnss .. The majority of the carburetors were Stromberg G- 3 type , as shown in Table 2. During the winter months , when the demand for coal is heavy , from 30 to 35 trucks are used . At the time the tests were made , only about ten of the trucks were in daily use , owing to the small demand for coal during the summer months , and scarcity due to labor conditions . Samples of the exhaust gas were taken on the trucks kept in service for summer hauling in order to determine the carburetor adjustment as used . Changes were then made to a more economical adjustment wherever possible , without sacrificing flexibility of operation and power . In every case the adjustments were maintained for maximum power , but were adjusted to the leanest position to give that power . In all but one case the carburetors were found to be adjusted too rich for maximum power and economy . These results are considered in detail in a later part of this report .

Jun 1, 1923

By V. A. Danielson

The Bureau of Mines examined sources, consumption, and movement of iron and steel scrap in the southeastern States--Alabama, Florida, Georgia, Kentucky, North Carolina, South Carolina, and Tennessee. Officials of the scrap-processing and scrap-consuming industries were interviewed, data was obtained from the published literature, and a canvass was made by the Bureau of scrap consumers. The Southeast generated excess scrap which was shipped to domestic and foreign consumers in about equal proportion. Total 1963 demand in the Southeast was 3,336,000 net tons, of which purchased scrap was 75 percent, foreign exports 13 percent, and domestic exports 12 percent. Alabama, with 47 percent of the purchased scrap consumption in 1963, was the most important scrap-consuming State, and Kentucky, with 34 percent, was the second most important one. Southeast demand was 4.8 per-cent of the total U.S. demand. Projected 1980 consumption is 8,340,000 tons. Scrap prices showed a slight downward trend for the period 1953-63, although gross consumption increased slightly. A significant trend in processing scrap in the Southeast is the preparation of smaller bundles or "briquettes" weighing from 75 to 150 pounds, which are easier for consumers to handle and inspect. Another significant development is the "shredding" of automobile scrap which produces a dense, clean scrap especially desirable for use in electric furnaces.

Jan 1, 1967