Search Documents

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By E. R. Bauer

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flatjack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the sup- port elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 1993

By D. N. Tallman

The Bureau of Mines has completed 4 yr of deep-bed filtration research comparing the efficiencies of granular magnesium oxide (MgO) and conventional filter sand in single- and dual-medium filters when filtering mineral-processing and mine waters. Bench and field evaluation tests were conducted using water types ranging from synthetic suspensions of asbestos, kaolin, metal hydroxides, and milled sand to process waters from magnetite beneficiation, iron ore flotation, granite cutting, and a steel mill. Even though the turbidity reductions were similiar, MgO filters were found to be advantageous when filtering water pretreated with alum because the volume throughput before breakthrough (turbidity > 1 NTU unit) was much more for the MgO filter than for the sand filter. Reduced head loss owing to the greater porosity of the MgO filter beds is potentially the most beneficial advantage in employing MgO as the filter medium, especially when filtering water pretreated with polymer flocculants. Granular MgO (periclase) is durable and can be backwashed Like sand. It is compatible with anthracite in a dual-medium filter and apparently is not poisoned by dissolved metals in the process water. No single solid-removal mechanism could be identified for the improved filtration observed with granular MgO.

Jan 1, 1987

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

Mining activity during 1977 was limited to the production of limestone, marl, and sand and gravel, all of which were used domestically. Public works projects consumed the major portion of the construction material produced. The consortium of oil companies operating as Esso Ventures Inc., drilled one exploratory well off the coast of southern Belize. For drilling the well, Exxon Corp. received a 57% working interest in the consortium's concession located 40 kilometers east of Puta Gorda. No other offshore drilling was attempted in 1977. Esso also drilled a well on the Anschutz Overseas Inc. concession in the Toledo District of south- eastern Belize. The attempt wee abandoned, but seismic activities continued.

Jan 1, 1981

By D. J. Parker

This report is based on data collected in and about the Liberty mine of the Liberty Fuel Co. by D. J. Parker and W. W. Kessler on December 13 and 14, 1933. An important phase of an examination to determine the general condition of a mine with respect to safety is the collection of dust samples from rock- dusted areas. Definite conclusions, based on intelligent interpretation of the analyses of such samples, can be reached only when the general condition of the mine is known. A similar examination and report were made on this property in January 1930 by D. J. Parker and R. I. C. Manning. Since that time much has been done by the management to improve safety conditions in this mine. The changes made will be noted in the course of this report. The mine is in Spring Canyon at Latuda, Carbon County, Utah, and is served by a branch line of the Denver & Rio Grande Western Railroad about 7 miles long and connecting to the main line near Helper, Utah. The writer desires to express his sincere appreciation for the many courtesies and helpful cooperation extended by Superintendent George Schultz and Mine Foreman F. W. Koelling.

Nov 1, 1934

By J. W. Thompson

CONSTRUCTION OF STATUTE-SALE BY ENTRYMAN. The timber and stone act (20 Stat., 89) does not forbid an entryman from alienating his interest in his claim; but the act makes illegal any prior agreement by which the entryman acts for another in the purchase. Worden v. United States, 204Fed., 1, p. 4, April, 1913. ASSUMPTION OF DEBT BY GRANTEE-LIABILITY TO CREDITOR OF GRANTOR. A grantee of a mine who agrees to pay the grantor's debts in part payment of the purchase price of the mines becomes to that extent the principal debtor, and the grantor becomes the surety, and the grantor's creditor may in equity enforce his claim against the grantee of the mine, and the grantor in such a case is not a necessary party. Silver King Coalition Mines Co. v. Silver King Consolidated Mining Co., 204Fed., 166, p. 169, April, 1913. RIGHT OF COTENANT TO MINE AND SELL. A cotentant in exclusive possession' of mining property who extracts and sells ore is entitled to charge against the proceeds of the sale the reasonable and necessary expense of its extraction and marketing, as in such case the cotenant is not a trespasser.

Jan 1, 1914

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM's). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. .It presents analytical data for 4, 457 samples, representing the products of 92 companies. The samples were collected by companies during June, July, and August 1956, As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the past 10 years is on page 5.

Jan 1, 1957

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By James F. O'Neill

Brown iron ore resources in Barbour , Butler , Crenshaw , and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama . The aggregate footage drilled was 18,010 linear feet . When developed , reserves of 12,664,000 long tons of crude ore were indicated , containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet . Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons . Beneficiation of samples by simulated log washing and use of a 1 / 8 - inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese . Screen- test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200 - mesh screen . Clay was prominent in micron - size slimes . Silica was deleterious in the minus 20 - mesh size . While an indicated 2,198,000 dry long tons of usable iron ore can be recovered , sink - and - float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing . However , applicable commercial processes have not been demonstrated .

Jan 1, 1965

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers In their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the first three sites: Bethel, Kivalina (Red Dog), and Omalik Lagoon. The mineral deposits near Bethel are primarily gold and mercury; the nearest deposit being 55 mites away. Because of the expense of constructing and maintaining a road over the poorly drained lowlands, the potential of Bethel as a port site in the near-term is considered to be low. The Kivalina site currently serves the Red Dog mine and has the potential to handle material for similar deposits in the area. Results from a lead-zinc mine model indicate that potential for additional mine development exists in the area. Coal is the major deposit type found near the Omalik Lagoon site. Due to environmental constraints, development of a large-scale mine producing coal for export is considered unlikely. A small-scale coal mine model was used to examine the feasibility of producing coal for regional use. This alternative may be feasible but would require conversion of heating/generating equipment in the area.

Jan 1, 2011

Reduce the potential for injuries in underground mines by providing an alternative to manually lifting and holding heavy roof-support beams. The Problem I-beams, rail sections, and wooden cross-beams are often used in mine haulageways where extensive roof support is needed. Studies by the Bureau of Mines have shown that many mines must resort to manually lifting, moving and installing these beams. Such manual-handling activities have the potential for causing injury to mine workers, particularly back injuries. I-beams used for roof support can typically weigh from 400-500 lbs. Rail sections weigh about the same as the I-beams. Wooden beams can weigh from 200 to 300 lbs. To lift a single beam usually requires the efforts of 3 to 5 mine personnel.

Jan 1, 1988