Search Documents

By Richard C. Barth

Fourteen field plots were established at active coal mines in the Northern Great Plains. A wedge was cut into spoil and backfilled with soil; soil depth ranged from 0 to 152 cm over a linear distance of 15 m. Perennial grasses were planted in each plot, and production was measured from 1978 to 1981. Based on spoil traits and biomass response patterns, plots were grouped into four types. Spoil for Type I plots was near neutral, slightly saline, nonsodic, and clay loam in texture. Perennial grasses reached maximum production with approximately 50 cm of soil depth. Spoil for Type II plots was characterized as sodic and fine textured; soil-depth requirements averaged 83 cm for maximum production. Spoil for Type III plots was characterized as strongly acid, and production increased throughout the soil depth range tested. Spoil for Type IV plots was similar to soil in chemical and physical traits; there was no production response to soil depth. Soil depth requirements were also dependent upon precipitation and species. In general, soil-depth requirements decreased in dry years and with use of introduced species. An appendix contains data evaluations on an individual plot basis.

Jan 1, 1982

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By T. G. Chapman

This paper has been abstracted from a forthcoming Bureau of Mines bulletin on the concentration of copper ores in North America. GENERAL DEVELOPMENTS IN CONCENTRATING COPPER ORES FROM 1912 TO 1932 During the east 20 years the milling of copper ores as practiced in the larger concentrators has chanced to such an extent that comparatively few of the machines in use at the beginning of this period remain in service today. Concentrating Practice in 1912. In 1912 the usual equipment for concentrating copper ores comprised jigs for the coarser sizes, tables and sand vanners for the intermediate sizes, and vanners for the finer crushed and ground material. Rolls operated in series under graded crushing conditions, were in common use for the liberation of the copper minerals; grinding by Chilean or Muntington mills ordinarily was confined to the coarser tailings of jigs and tables.

Jan 1, 1934

Another major aluminum company announced intentions to follow other domestic producers recent price actions by raising its unalloyed ingot quotes by 3¢ to 44¢ per pound, effective June 1, 1976. COBALT: All final data for 1975 are included in the table for cobalt on page 23. Demand in March increased significantly for the second month in a row, signaling a recovery from the previous year's relatively low demand levels. Imports of cobalt tripled in March over those of February. This should partially offset reduced sales of cobalt excesses from the National Stockpile. Import projections for the next several months have been lowered because transportation difficulties in Zaire are expected to result in reduced shipments.

Jan 1, 1976

By B. H. Clemmons, C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent on improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silverbearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores that because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Mar 1, 1965

With IIT research institute as a cosponsor, this seventh mineral waste Utilization Symposium was funded by the Bureau of Mines through its Division of Mineral Resources Technology. Environmental scientists and engineers from five countries (Canada, Netherlands, Austria, England, Guatemala) besides the United States participated in the symposium, which was held Oct. 20-21, 1980, at the Chicago campus of IIT Research Institute. Of the 25 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial waste, and scrap metal, 21 are summarized herein.

Jan 1, 1982

By Paul M. Tyler

The technology of clay and the manufacture of ceramic products therefrom, and also the clay resources of most of the individual States, are already covered by a voluminous literature. The present resume touches these matters only briefly; its purpose is essentially to bring together in small compass certain of the elementary factors affecting the potential commercial value of a clay deposit. In its preparation the author made extensive use of the annual chapters on Clay in Mineral Resources of the United States and in the two annual issues of the Minerals. Yearbook that succeeded them. For careful review and constructive criticism of the manuscript, the author is indebted to Hewitt Wilson. GENERAL DESCRIPTION The term ?clay? includes a great variety of substances that may differ widely in chemical mineralogical and physical properties. No two clays are exactly alike. All of them however, have the prominent characteristic of becoming more or less plastic when wet. Nearly all of the useful clays can be molded into articles, will hold their shape while being dried, and can be converted into a hard, rocklike substance by heat. Clay may, and in fact usually does, consist of a number of minerals among the commonest of which are kaolinite, quartz, feldspar, iron oxides, mica, bauxite, calcite, and manganese oxides. Organic matter is often present. Pure kaolinite, which has the formula A1203. 2 SiO2. 2H2O, is ordinarily, considered to be the parent "clay substance," butt most clays contain other hydrated mixtures of alumina and silica (aluminosilicic acids) along with indefinite amounts of sand and other nonessential minerals3/ Even, this so-called inert matter affects the plasticity, drying shrinkage, ease of drying, and final density, and at high temperatures may react chemically with the clay substance.

Jan 1, 1929

By George S. Rice

This bulletin traces the growth in the belief in the explosibility of coal dust, summarizes the experiments and mine investigations that have established this belief, and gives the present status of pre- ventive measures. It has been prepared in accordance with the pro- visions of the acts of Congress authorizing investigations relating to the causes of mine explosions, and contains references to and descrip- tions of experiments made at the Federal testing station at Pittsburg, Pa. This station was inaugurated under the United States Geo- logical Survey, and was transferred to the Bureau of Mines on the establishment of the latter on July 1, 1910. Only within comparatively few years has the dry dust of bitumi- nous and lignitic coals been generally recognized as an explosive agent more insidious, threatening, and deadly to the miner than fire damp. Fire damp carries its own flag of warning-the "cap" in the safety lamp-but coal dust, though visible, does not attract attention until present in large quantities. Fire damp is of local occurrence, and except in notable and very exceptional cases is controllable by careful manipulation of ventilating currents. If by mischance a body of fire damp is ignited in a mine, the force of the explosion may be terrific, but the effect is local unless dry coal dust is present, or unless (as it very rarely happens) an explosible mixture of methane gas and air extends through large areas of the mine. In a dry mine dust accu- mulates everywhere, and the blast from the ignition and combustion of bituminous dust may traverse miles of rooms and entries and wreck structures at the entrance to the mine. The comparative potential destructiveness of gas and of bituminous dust is strikingly shown by the history of the Pennsylvania anthracite mines. These mines not infrequently have large inflows of gas, and the resulting mixtures of gas and air have sometimes been ignited, yet no such wide-sweeping explosions have taken place, despite the presence of dry anthracite dust, as have happened in excellently ventilated bituminous mines.

Jan 1, 1911

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By E. C. Yeager, E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. G. Gernes, W. L. Patty

"In July 1943, the Bureau of Nines received an appropriation to investigate the beneficiation of Minnesota iron ores through the use of lignite. The broad objective was to find a way to link the large deposits of lignite in North Dakota with the low-grade iron ores of Minnesota. It was proposed that sponge iron might be made through new methods of processing, and one of the objectives was to determine the possibilities of gaseous reduction of fine ore. The problem of obtaining high-hydrogen reducing gases from lignite was assigned to the Subbituminous Coal and Lignite Section of the Bureau of Mines in August 1943.Through the advice of technical consultants and men familiar with the mineral resources of Minnesota and North Dakota, a tentative program of development was outlined. The first proposal was to study the gasification of lignite briquets in a standard water-gas machine. Previous experience with gasification of lignite indicated that the raw fuel would not be suitable for use in the conventional water-gas process on account of degradation, but gasification of lignite briquets appeared possible. Through the cooperation of the Northern State Power Co„ a series of tests was made at the company's plant in Grand Forks, N. Dak., on lignite-char briquets made by the Lehigh Briquetting Co. at Dickinson, Dak. These briquets are made by the Lurgi process, and they have been used satisfactorily as a domestic fuel. The object of the tests was to compare gasification properties of lignite-char briquets with those of gas. coke made from Kentucky coal, normally used in the Grand Forks plant. The tests revealed that the lignite-char briquets were not suitable for gasification, in the standard water-gas process because of disinte-gration and low efficiency caused by loss of fine carbon.While these investigations were underway, a joint Minnesota-North Dakota Development Commission was formed to aid in planning investigations on development of mineral resources of the two States. Some members of this commission were technical men, who with consulting engineers on the Bureau's staff made up an unofficial technical committee, and assisted in solving certain problems connected with gasification of lignite and beneficiation of iron ores. This committee has been of 'real assistance in guiding the investigation.A technical meeting was held in Minneapolis on November 10 and 11, 1943, for further discussion of objectives and certain technical problems. Results of tests on lignite briquets were presented, and several reports analyzing other methods of gasification were discussed. The Reyerson-Gernes process for the continuous gasification of lignite in an externally heated retort was considered from several angles. This process differs from others in that the natural moisture in the coal is utilized to help gasify the coal, and the volatile matter is largely decomposed. Although this process had been carried out successfully in a small steel retort, no definite design for a commercial-scale retort had .been developed. It was first proposed that the process might be carried out in a Glover-West retort. However, it was brought out that a Glover-West retort would require modification to simulate the process correctly, and that good results might not be obtained even then owing to the leakage of gas through the refractory walls and to an anticipated low rate of heat transfer at the gasification temperature suitable for lignite. Further, the probable leakage of inert furnace gas into the water-gas would be adverse to the Objective to obtain a gas that could be purified to 96 percent hydrogen."

Jun 1, 1946

By R. A. Hatch

This report summarizes the results of nearly 8 years research on and production of synthetic mica at the Electrotechnical Experiment Station of the Federal Bureau of Mines, Norris, Tenn. This program was undertaken at the request of the United States Department of the Navy and was financed mostly by the Army Signal Corps and the Navy Bureau of Ships through a contract with the Office of Naval Research, The original objectives included fundamental studies of fluor-phlogupite and other fluorine-micas and production of synthetic mica sheets on a pilot-plant scale. The first 3 years of this project were devoted mainly to a search for practical solutions of the many problems involved in designing and constructing a pilot plant for crystallizing fluor-phlogopite mica. The first and most urgent need was a suitable container for the corrosive mica melt. After extensive study, it was concluded that platinum, graphite, high-silica fire clay, and silicon carbide were the most promising refractories for crucibles; but none was perfect. Silicon car¬bide seemed to have the better combination of qualities, combining good corrosion resistance with oxidation resistance.

Jan 1, 1957

By Gerald M. Bandholz

Exxon Minerals Company, a division of Exxon Corporation, has been exploring for base metal deposits in the Precambrian volcanic rocks in northern Wisconsin since 1970. Aerial electromagnetic surveys of the area, conducted in 1974, reported an anomaly, near Crandon, in Forest County. In the summer of 1975, the first diamond drill entered the anomaly, representing the 25th prospect Exxon had drilled in Wisconsin. This first hole revealed significant mineralization containing zinc and copper. Subsequent drilling confirmed the discovery of a sizeable zinc-copper massive sulfide are body. 1.1.2 Location The deposit is located in northeastern Wisconsin within a topographical high called the Northern Highlands region. The deposit lies about 5 miles directly south of Crandon and about 2 miles east of State Highway 55 on Sand Lake Road (see fig. 1). Other local communities include Rhinelander 28 miles west, Antigo 45 miles south, and Iron River and Iron Mountain, in Michigan, 75 and 44 miles east and north of Crandon respectively. In relation to the lakes and streams, the deposit lies 0.25 miles north of Little Sand Lake, and about 1 mile south of Swamp Creek.

Jan 1, 1981

By D. Harrington

Hatch (260) made the following pertinent statement regarding the present status of engineering design of dust-control equipment: Textbooks on ventilation and engineering handbooks devote little or no space to methods of control of industrial dust, and in the technical journals papers on fundamental engineering design of equipment are conspicuous by their absence. In a recent bibliography of the literature on pneumoconiosis less than 1 percent of the articles dealt with the engineering control of the disease. The science of dust control has not developed beyond the stage of trial and error, and the design of structures for the suppression of dust is based almost entirely upon empirical data together with one or two elementary formulas. The latter were derived from the generalized experience in a limited number of Industries such as woodworking, where conditions and requirements are not at all like those, for example, in a sand-pulverizing plant. Wide experience and good judgment are essential to the proper use of the scanty information that has been collected and systematized. Without attempting to minimize the importance of experience in engineering design, it is necessary to point out that most of the past experience obtained in the empirical design of dust-control equipment was not evaluated by means of quantitative studies of the actual reduction in dust , fence, past experience does not necessarily furnish the proper guide for future design. In fact, recent surveys in certain industries, employing modern methods of investigation, have shown that existing equipment is in many cases inadequate.

Jan 1, 1935

By Robert M. Becker

This report (the second in a series of five) presents the mathematical development in extending the theory of sample reliability from a sample consisting of a fixed number of items to a sample consisting of a fixed amount of items. Examples of a fixed amount of items per sample are samples consisting of a fixed weight or a fixed volume of unequal size particles. The probability distribution functions (those here called the compound binomial and compound multinomial functions) are developed from fundamentals. Their distributions are generalized to include some measured characteristic of the items. Infinite population moments are derived from moment-generating functions, while finite population moments are developed from corresponding infinite population moments using the finite probability operator defined in part 1 of this series.

Jan 1, 1964

The wealth of a nation may be measured in many ways, but one of the most important is its natural resources, particularly its minerals. Minerals create the wealth upon which economic prosperity and defense preparedness rest. Managing mineral resources for the benefit of all Americans continues to be an important national goal. In its 78-year history the U.S. Bureau of Mines has established itself as the world's premier mineral information and research agency. Its authoritative, comprehensive data and pioneering research have contributed significantly to a strong U. S. mineral position in the world.

Jan 1, 1988

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

The goal of the Bureau of Mines diesel engine research program is to reduce exhaust emissions and minimize the risk of fires and explosions caused by the use of diesel- powered equipment in underground mines. This program has led to a fundamental understanding of the problems and to solutions that allow diesel equipment to be used safely and effectively. This volume contains reports of the presentations made at the Bureau Technology Transfer Seminar on Diesels in Underground &fines given in Louisville, KY, and Denver, CO, on April 21 and April 23, 1987. It also contains three reports of related research, not presented at the seminar, which highlight the significant achievements of a joint US.-Canadian research program on diesel emission control technology for underground mines. Topics covered in this volume include discussions of industrial hygiene problems associated with the use of diesels, accident statistics, fire and explosion control systems, measurement of diesel pollutants, emission control techniques including engine maintenance, fuel additives, diesel particulate filters, and ventilation of diesel sections. An alternative to diesel power, the hydrogen-powered mine vehicle, is also described.

Jan 1, 1987

By Rita D. Sylvester

"This compilation lists and summarizes publications by Bureau authors published in the regular Bureau of Mines series, in scientific, technical, or trade journals, or in other media; those available from the Bureau of Mines are indicated. Patents issued to Bureau personnel are also listed, and instructions are given on how to apply for permission to use them. One of the outstanding features of this Special Publication is an exhausive subject and author index. IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and present their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries, The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminar's; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1970, to December 31, 1974. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;3 and the 5-year lists of Bureau publications and articles from January I, 1960, to December 31, 1964,4 and from January I, 1965, to December 31, 1969.5 It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1970, to December 31, 1973."

Jan 1, 1975

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased or decreased), and provides a bridge where possible from the old Schedule A classification sys tem to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

Aluminum Production. -By October 1, Aluminum Company of America will restart a 35,000-ton-per-year unit at its aluminum smelter at Rockdale, Tex., restoring that facility to its full capacity of 325,000 tons annually. Primary Ingot Price Increase. -Most U.S. aluminum producers in mid-September were quoting a price of 72 cents per pound for primary aluminum ingot. On September 19, Kaiser Aluminum & Chemical Corp. announced that it would increase the price of primary aluminum ingot 4 cents to 76 cents per pound.

Jan 1, 1980