Search Documents

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By W. R. Gilliland, G. W. Jones

"One-phase of the accident prevention program of the Bureau of Mines is the determination of the explosion hazards of various combustible gases and vapors encountered,mining and allied industries and the development of means and methods of eliminating them.Gasoline is foremost among the combustible-liquid's as to quantity used and variety of applications in industry, It is a chief contributor to the causes of fires and explosions, taking an enormous yearly toll in property damage and considerable loss of lives.The results presented in this report evaluate the effect of various gaseous inert substances, which owing to their chemical composition, should be of considerable value in the prevention of gasoline fires and explosions. The substances investigated are as follows: Nitrogen (N2), automobile exhaust gas (85 percent N2 + 15 percent CO2), carbon dioxide(CO2), dichlorodifluoromethane (CCl2F2-Freon-12), trichloremenofluoromethane (CC13F-Freon-11), and dichloromonofluoromethane (CHCl2F-Freon-21).The general term ""gasoline"" designates a combustible liquid of such characteristics as to give satisfactory operation without preheating in spark-ignition-type internal-combustion engine. It comprises a complex hydrocarbon mixture having a limiting distillation range and produced commercially by distilling or ""cracking"" crude petroleum or other various petroleum stocks. Small proportions of other substances may be incorporated in the gasoline to enhance its antiknock properties or operating characteristics in internal-combustion engines and to increase its stability during storage, transportation, and use.It is thus seen that gasoline may have rather wide variations of chemical and physical properties, and it would: appear that the results of any investigation dealing with one particular gasoline might not be applicable to other types. However, as indicated by the results given in this report, the inflammable properties of different gasolines at normal atmospheric temperatures are influenced largely the mars volatile hydrocarbons containing 5, 6, 7 carbon atoms- in the molecule, and that the heavier constituent of higher molecular weight have a minor influence on the inflammable properties at ordinary temperatures."

Apr 1, 1946

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By D. A. Elkins

This report is the second of a series of three that will evaluate, in order, the metallothermic, carbothermic, and electrolytic methods of magnesium production. The historical development of the carbothermic process is outlined. Production costs varying from 38.9 to 21.8 cents per pound of magnesium are estimated for different versions of the process. Additional suggested process modifications are listed. The technical and economic potential of the different versions are compared. Areas deemed most promising for future research on the process are delineated.

Jan 1, 1967

By Ralph H. Whaite

In undermined urban areas, new solutions to subsidence problems are being sought. The Bureau of Mines is investigating a hydraulic backfilling technique whereby fill material is pumped as a slurry through a closed system and widely distributed in inaccessible mine workings from a single borehole. A full-scale demonstration was completed in 1973 in Scranton, Pa., which is underlain by abandoned anthracite mines in several coalbeds superposed one above another. A 30-acre residential area was stabilized by injecting about 450,000 cubic yards of crushed mine refuse into two coalbeds through five injection boreholes. Nearly 200,000 cubic yards was injected through one borehole from which the material moved into the mine workings on all sides; the injected material reached a maximum lateral distance of 640 feet and filled mine openings from floor to roof. In the gravity-feed method formerly used to backfill inaccessible mine workings, quantities of fill injected per borehole averaged about 300 cubic yards. The gravity-feed method required many closely spaced injection holes and provided incomplete filling. The new method, designed for inundated mines, proved successful also in mine workings about mine-water pool level. Distribution of slurry through a buried pipeline minimized disturbance to the community.

Jan 1, 1975

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By John B. Ivey

This is a geologic study of the U.S. Bureau of Mines Oil Shale Tract in the Piceance Creek Basin of Rio Blanco County, Colorado for the preparation of a set of detailed surface geologic maps, measurement and identification of joint attitudes and frequencies, and the classification and mapping of the soils of the area.

Jan 1, 1978

By A. E. Raddatz

The Bureau of Mines is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nev., hot springs ores. The deposit contains disseminated tungsten that cannot be beneficiated by conventional techniques and must be treated by hydro-metallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hours, quenching in a solution containing 1.5 parts of Na2C03 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution-to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hours, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 wt-pct W03. The pregnant solution contained 11 g/l W03.

Jan 1, 1982

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Steven W. Schmauch

A mineral survey by the U.S. Bureau of Mines and U.S. Geological Survey indicate the Blanco Mountain RARE II area has low potential. Lode deposits consist of small, mineralized quartz or quartz-gossan veins. The veins are sparse and widely separated and lead, silver and gold content is restricted in amount and concentration. No gold or other potentially economic minerals were found in a placer deposit. There is no evidence of industrial mineral, geothermal, or energy resource potential in the study area. INTRODUCTION A mineral resource survey of the Blanco Mountain RARE II area (No. 5059), Inyo and Mono Counties, California was conducted in July 1981. This report summarizes the results and interpretations of the Bureau of Mines investigation.

Jan 1, 1982

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

Real gross national product increased at a larger-than- expected annual rate of 8.3 percent in the first quarter of 1984, with both consumption and investment spending increasing significantly in real terms (table 1). Residential and nonresidential fixed investment increased at annual rates of 25.7 and 14.6 percent during the first quarter of 1984, and investment in nonresidential structures, which declined in 1983, also increased during the first quarter of 1984, nearly attaining its 1982 level. The annual level of personal savings increased $27.7 billion, while the personal savings rate (the ratio of personal savings to disposable income) increased to 5.8 percent during the first quarter. The increase in the personal savings rate comes as welcome news to analysts concerned over the flow of loanable funds to the private sector and the impact on interest rates in 1984 of increased private and Government demands. U.S. Minerals Industry Performance A major upswing in the performance of the metal mining sector occurred during the first quarter of 1984, with production increasing almost 11.2 percent from January to March, The recovery of the metal sector is also reflected in the performance of primary metal industry profits, which were positive during fourth quarter 1983 following seven consecutive quarterly losses (table 1). Two thousand nine hundred more metal mining production workers were employed in February 1984 than in February 1983.

Jan 1, 1984

By Charles E. McCarthy, MORTON T. PAWEL, E. A. GEE, FRANK S. RIORDAN

Large tonnages of the magnesium silicate mineral , olivine, are known to exist in the mountains of western North Carolina and in the Puget Sound region of Washington. The North Carolina deposits alone are reputed to contain at least 230 million tons of ore averaging 45 to 49 percent of magnesium oxide In both areas the mineral is readily accessible and can be mined by the simplest methods ; one of the largest of the Washington deposits is located at tidewater .

Sep 1, 1946

By BUREAU OF MINES

This report is submitted in accordance with the provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1953 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5043, Part I - 011 From Coal. R. I. 5044, Part II 011 From 011 Shale. - Identical in each report, the introduction summarizes research progress made in 1953 under the entire Synthetic Liquid Fuels program. A free copy of each of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Apr 1, 1954

By M. C. Irani

This study is a survey of supply and demand for minerals, metals, alloys, and compounds used by the chemical industries in the Ohio River Basin (ORB) area of Ohio, Pennsylvania, and West Virginia during 1967. Data for the study were obtained from completed questionnaires received from chemical manufacturers and from interviews with officials of chemical companies and mineral producers and distributors. The information includes kind, quality, quantity, values, sources, specifications, uses, and methods of transportation. Results of the study show that of the total value of mineral materials consumed by the chemical industry, manufacture of inorganic chemicals consumed 46 percent; fertilizers, 22 percent; and soaps and detergents, 19 percent. Fifteen commodities accounted for 91 percent of the total value of mineral materials consumed. Five of these--phosphates, potash, salt, sulfur, and titanium dioxide--accounted for 59 percent of the total.

Jan 1, 1970

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents-ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962