Search Documents

By Svatopluk Zeman, Zbynek Akstein, Jiri Pachman, Ahmed Elbeih, Marcela Jungova

BCHMX (cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole or Bicyclo-HMX) was studied as an energetic component of three different plastic explosives based on three matrices: C4 matrix, semtex10 matrix and silicone matrix. The original plastic explosives, Composition C4 - based on RDX (1,3,5-trinitro-1,3,5-triazinane), Semtex 10 explosive based on PETN (pentaerythritoltetranitrate) and plastic RDX-silicone, were included for comparison. Sensitivity and performance parameters were studied.

Jan 1, 2011

By Matias Suarez, Diego Zenteno

This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002).

Feb 1, 2020

By Matias Suarez, Diego Zenteno

It is known that the introduction of electronic timing in the sequencing of blasting has changed the vision and way in which mining is developed. It is possible to deal with more complex and sophisticated drilling designs, without compromising productivity or safety. It has been shown in various studies, that a correct timing of the blasting provides an improvement in the improvement of the processes downstream, due to a decrease in the resistance of the resulting fragments coming from the interaction of the waves generated in the detonation of explosive loads. On the other hand, it has also been shown that variations in the composition of a same type of explosive, has a significant influence over the resistance of the blasted material, also the energy associated to break it, affecting directly its degree of fragmentation. This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002). This study focused on the methodology of the formation and measurement of seismic pulses, through the rock massif. For this purpose, seismic pulses were acquired in the field and then, the different dynamic phases of the wave were molded mathematically, with the purpose of favoring the coupling between them.

By Debra Satkowiak, Ronald Thomas

The Institute of Makers of Explosives (IME), a non-profit safety and security organization founded in 1913, is known for its industry best practices, Safety Library Publications (SLP), some of which have been incorporated into rules by regulatory agencies. The IME developed the first commercial storage, quantity distance (Q/D) table titled “The American Table of Distances” (ATD). It was developed by IME’s legacy association in 1910 and was originally based on observations of structural damage from 117 accidental explosions involving small to very large amounts of explosives, primarily dynamite and black powder. In 1930, the IME published a book, compiled by Ralph Assheton, called the “History of Explosions on Which the American Table of Distances was Based”. The distance in feet in the ATD were founded on the measurements at which inhabited buildings sustained substantial structural damage from the accidental detonation of explosives. For example, minor damage such as window glass breakage and the “shaking down” of plaster was not considered substantial structural damage. Other damage to property that was readily repairable was also not considered “substantial.” It was concluded that unless some integral portion of the building was damaged, the occupants would not be subjected to serious risks.

Jan 1, 2017

By D J. P Jordan, C V. B Cuningham, A J. Rorke, C G. Ladds, O L. Davey

"During the early stages of the boxcut mining at the Arthur Taylor Colliery, Open Cast Mine(ATCOM), problems were experienced with blasting results. Very large boulders andportions of completely unfragmented rock were commonly encountered. A full blastmonitoring programme was instigated by the mine and the explosive supplier to solve theproblems and to optimise future blasting operations at the mine."

Jan 1, 1993

By Peter Moser, Mark Ganster, Radoslava Ivanova, Florian Bauer

Blasting accurately in underground drifts and creating a smooth contour requires proper drilling, knowledge about the apparent geology, a well designed blast pattern and ideally a smooth blasting product. These products are usually cartridged explosives with less energy and are charged in the contour holes in order to reduce the energy concentration and therefore the cracking into the surrounding rock. With the development of a new contour blasting system, a device can now be delivered to the industry that that avoids the additional storage of cartridged products when bulk explosives are used. The system consists of a foldable hose that is charged with bulk emulsion, in the same way as the rest of the blast, from the base to the collar of the hole. It centers automatically in the borehole and provides a decoupled charge. The paper describes the system in detail, gives background information on smooth blasting and presents the first successful field tests using the system in the drifts of an underground mine. It shows the advantages of blast results that produce more stable contours that reduce the amount, time and cost for support but also increase safety underground.

Jan 1, 2012

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By Johan Finsteen Gjødvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad. This has been done by use of an online survey through the most of 2018. Questions have been raised on vibration monitoring during blasting. The existence of norms, guidelines or standards and how they are used. Even though the questions have been kept at a high level they are formed to try to map the different national standards use of such things as frequency, guidance on monitoring position, distinction between different types of structures, requirement to the equipment and more. Furthermore a few initial questions have been raised on other environmental monitoring relevant for blasting. The respondents are national, cooperate or individual members of EFEE. The answers are experts in the use of explosives and vibration-monitoring in their respective countries. More than 60 have answered the questionnaire from 29 different countries. Mainly European as well as other nations including India, Israel, Nigeria, Saudi Arabia, UAE, USA, Greenland and Hong Kong. By analysing the incoming answers, the differences and similarities in vibration monitoring of the respondents has been clarified and mapped. Where possible other environmental monitoring has also been analysed. Where needed the different guidelines, standards and regulations have been visited to verify the answers and further elaborate on the comparison.

By E. Contestabile, B. von Rosen

Recently, the Canadian Explosives Research Laboratory (CERL) completed its investigation of a truck accident, which involved 18,000 kg of commercial explosives, 13,000 kg of which was ANFO. Over the three years of the investigation unconfined burns of piles of ANFO were performed. In its final phase of the investigation, two burn trials were performed in an attempt to recreate the accident and the ensuing fire, to identify probable mechanisms that led from burning to detonation. Two full-scale tests were performed using complete tractor-trailers. In each test, the trucks were placed in a jack-knifed position with the majority of the explosives located on the ground in front of the trailer. The explosives were placed in a manner to provide maximum confinement and to maximize the possibility of explosion/detonation while remaining as faithful as possible to the perceived accident geometry. The tests were instrumented using thermocouples and video cameras and observations were made on the burning characteristics of the explosives, tractor-trailer and tractor-trailer components. In each test the explosives burned calmly for approximately 80 minutes. There was no evidence of explosion or of unstable burning. The heat caused several truck components to rupture violently. These included the tires, some engine components, the spring brake chambers and possibly the fuel tanks. Of these, the most violent were the truck tires. Although no quantitative data was gathered on rupture violence or fragment velocity, it is speculated that several truck components might produce fragments with sufficient energy to initiate heat-sensitised explosives under favourable circumstances.

Jan 1, 2004

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011

By Catherine Johnson, Barbara Rutter, Phillip Mulligan

Shock tubes, shock tunnels, and blast tubes have been widely used by explosive researchers and shock wave investigators to understand the characteristics of shock waves. Rectangular, cylindrical, and conical are the three simple geometries commonly used in shock tube and shock tunnel testing. These geometries result in shock waves that resemble the Friedlander curve’s simple exponential decay. However, geometries that are more complex have not been studied. This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile. Shock wave profiles were measured inside and outside the LATS to investigate the geometry’s effect. A representative shock wave profile from each geometry and open-air explosive testing were compared visually showing the geometries effect on the shock wave profile. The LATS produced a waveform with four pressure peaks behind the initial shock front, which were found to be associated with the four rectangular sections. The resulting pressure trace was compared to pressure traces from simulated urban bombings. The number of turns in an urban environment equated to a new peak, which is caused by additional expansion sections of the shock tunnel. From this observation, complex geometry shock tunnels can be purpose built to simulate an explosion in an urban setting. The use of shock tunnels with complex geometry in simulating urban bombings can allow for numerous representations and a better understanding of profiles produced during an urban bombing or similar scenario.

By Bradley C. Paul

Similar rock formations exhibit great variability in resistance to fragmentation during crater blasting. This observation was made during an attempt to calibrate the Kuz-Ram blast fragmentation model for crater blast geometries used in a modified in situ mining method for copper. The KuzRam equation is used to predict the fragment size distribution from blasting and includes a term called the "rock factor" to account for the fragmentation characteristics of the material. A data base of field scale crater shots in oil shale was available to supplement more limited data on copper ores. First, the blast geometry terms of the Kuz-Ram formula were modified to fit field data with various crater blast geometries. Rock factors were chosen to center the predicted curve on the curve representing observed fragmentation. Next, five possible sources of variability in rock factor were investigated: the grade of the oil shale, the aspect ratio of the charge, the type of explosive, the charge depth, and the rock itself.

Jan 1, 1989

By Jason Wilkinson

Drilling operations are a vital component of surface mining, directly influencing productivity, safety, and cost efficiency. This paper explores a multi-faceted approach to drill optimization, focusing on minimizing delays, and enhancing operational effectiveness. Key areas of inefficiency such as shift changes, fuel and water delays, and time lost between drilling holes are analyzed to identify actionable improvements. Equipment related factors, including the frequency of drill bit and drill steel changes, as well as the condition of deck bushings, are evaluated for their impact on downtime and performance consistency. Additionally, the integration of smooth drives and shock subs is examined for their role in reducing vibration related wear and improving drilling precision. Optimization of pattern approach strategies is highlighted as a means to reduce non-productive movement and align drilling with blast design more effectively. To support continuous improvement and accountability, the implementation of a driller scorecard is proposed. This tool enables the measurement of individual performance based on key operational metrics, fostering a culture of data driven management. Through a combination of field data analysis and best practice recommendations, this study provides a comprehensive framework for enhancing drilling productivity in mining operations. The findings aim to support mine operators in achieving higher efficiency, reducing operational costs, and extending equipment life through targeted optimization strategies.

Jan 26, 2026

By R. J. Cefalo

Blast and mining spillover between phases or critical areas of the pit is a continuing problem in the mining industry and a safety concern for operating mines. The challenge for many mines is to produce the highest value in the shortest amount of time for any project. For any project, the top priority of any mine is producing ore as fast as possible. The next challenge is to keep that ore feed continuous. To achieve continuous ore feed, pits are designed with multiple phases that are connected and are mined at different elevations. This difference in elevation causes dangers with spillover between the phases during mining, drilling, and blasting. This paper covers an incident that occurred at an active mine and the work completed in creating a spillover control program over an active mining phase. The drill and blast technical group was responsible for creating blast patterns to reduce spillover between these phases. Unrealistic goals and expectations were initially set for the area of the pit. The drill and blast technical group needed to figure blast objectives and work with the geotechnical team to align with these goals. This paper will go over the executed example of setting up spillover targets and expectations for multiple sections of an operating mine. Different sections of the pit had different control measures and blast objectives due to narrow laybacks and double benching. The use and value of blast objectives and goals were beneficial in setting expectations and measuring design success. Having unrealistic blast goals can set up the operations to fail or get frustrated in trying to work on an impossible task. The problems and risks of phase interactions for many open pit operations need to be considered in the design process, along with designed controls that minimize the probability of any safety incident. Mine designs are being created in the industry and do not consider phase-to-phase mining interaction and the impact it would have on safety or production. The best future for safer mines is blast patterns that reduce spillover between phases of mining and pit designs that might account for spillover interaction.

Jan 1, 2024

By Dr. Tristan Worsey, Dr. Jhon Silva-Castro

Confinement is an important aspect of blasting. Reducing and increasing confinement can determine whether a blast design performs properly. Over-confined shots usually have poor fragmentation, higher vibrations, and stemming ejection, and unconfined shots usually have a lot of air blast and fly rock. When talking about confinement in blasting, static confinement conditions are typically referenced. Static confinement conditions are ruled by free faces, shot muck, burden, spacing, stemming, hole depth, toe, etc. All these conditions exist in a static state. Static confinement conditions are generally analyzed before the shot takes place, but once the shot starts, the conditions will change according to the sequence and delay of the shot. Once the shot starts, Dynamic confinement takes place. For the authors, Dynamic confinement is the confinement conditions that exist for the charge when it fires and should account not only for the variables included for the static confinement but also for the time and sequence of the shot. The paper explores the theory of dynamic confinement and its role in influencing blast performance. Time and sequence are the main influencers of dynamic confinement and will be the focus of the paper. How to generate the appropriate timing based on blast design, dynamic confinement, static confinement, and geology will also be discussed.

Jan 21, 2025

By Braden Schmidt

The following full paper will go into the products, techniques and people who work in the avalanche control industry giving insight to the other members of the ISEE an overview of the niche blasting that is Avalanche Control.

Feb 1, 2020

By Dr. Anurag Agrawal, Steve Franklin, Clint Zimmerman, Elijah Williams

In a time when data has become a highly valued commodity within many mining and quarry operations, managing large amounts of current and historical information can be difficult. If not managed properly, trying to leverage the data to make informed operational decisions promotes another challenge. Geographic Information System (GIS) is an environment that uses computers and software to create, manage, analyze, and map all types of data. Currently, the mining industry is faced with a challenge to produce the demanded critical metals and minerals that drive our economies. GIS is leveraged in many large mining industries today to help drive decisions, save cost and plan for future operations. Specifically in the Drilling, Blasting and Quarrying industries, data is being captured at many different levels, whether it is a subsurface geological, blast performance, quarry surveys, loading and hauling, or crushing performance. Pen and paper logs and reports compiled lack the dimension that GIS can bring for extracting value from real-time or historical data. GIS connects data to maps, integrating location data with all types of descriptive information. Paired with Artificial Intelligence, additional analytical layers can be built on platforms to extract data and automate workflows. Having the ability to encompass several forms of collected data to drive operational decisions can bring huge savings to the bottom-line. This paper will dive into the areas where GIS data can drive value into operations by assisting in the management and analysis of the types of data being captured, specifically with Drill and Blast. Whether it is tracking haul road conditions, monitoring locations of equipment, environmental conditions, quantifying blast performance or developing a quarry plan based on geological models. GIS can collectively encompass all of this data to bring tremendous value to the operations, improving safety, efficiency and production.

Jan 21, 2025

By David Lilly, Robert Ethier, David Bremer

The Lafarge Ravena Cement Plant in Ravena, New York demonstrated continuous and extraordinary improvement in productivity during the past several years. The factors driving continuous improvement at the Lafarge Ravena Plant include: 1) Management techniques including regular scheduled and effective Blasting Optimization Team meetings. 2) A real time blasting database to guide blasting product and procedure decisions. Key decisions involved all levels of quarry and blasting supplier personnel and a close working relationship between production and blasting areas of expertise was demonstrated. 3) Blast optimization and optimization of quarry operating parameters such as blast location relative to crusher location, hours worked, etc.

Jan 1, 2007

By Douglas R. Simms

O & G Industries, Inc. owns and operates a number of rock quarries within the State of Connecticut. These rock quarries are surrounded by residences and commercial neighbors who have concerns related to blasting. In addition, local commissions which issue the mining permits to O & G are required to hold public hearings, prior to issuing the annual permits each year.

Jan 1, 1994