Search Documents

By Alexey Musatov, Georgy Cherkashov

Based on geochronological data it was confirmed that hydrothermal discharge has an episodic character: active and inactive periods of the seafloor massive sulfides (SMS) formation alternate (Cherkashov et al., 2017). There is an assumption of correlation of the periods of magmatic and hydrothermal activity with the stages of glaciation (Lund et al., 2016). During the cold periods, the level of the ocean was reduced from 70 to 150 m depending on the glaciation scale (Spratt, Lisiecki, 2016). As a result, the hydrospheric pressure on the upper mantle decreased and could provide increased magmatic and hydrothermal activity (Lund, Asimow, 2011). This assumption is confirmed by the correlation of warming and cooling stages with increasing of hydrothermal input to the bottom sediment near hydrothermal fields. According to data (Lund et al., 2014, 2016; Middleton et al., 2015) the peaks of hydrothermal activity, expressed in the layers of metalliferous sediments at the East Pacific Rise and the Mid-Atlantic Ridge, roughly correspond to the last two periods of cooling (20 and 60 ka). To test this hypothesis, we tried to compare the sequence of warm and cold periods in the Pleistocene with the dating of SMS reflecting the periods of hydrothermal activity. Results SMS samples were obtained from 12 sites within the Russian Exploration Area at the MAR segment 12-20°N. The results of dating 198 samples by the 230Th/U method demonstrated the absence of correlation between hydrothermal activity periods in different hydrothermal fields (Cherkashov et al., 2017). It was proposed that each field has its own evolutions scenario. Considering this point, only the oldest SMS dating for each field which fixed the beginning of hydrothermal activity was selected for comparison with the cold/warming periods.

Jan 1, 2018

By Jiahua Pan, Yanxiong Mei, Shuqin Liu, Rongfu Pei

Growth characteristics of Co-rich crusts from the Western Pacific have been approached. The thick crust shows 3 structural layers: compact upper layer, porous middle layer, and compact lower layer. The middle and lower layers have obviously different microscopic structure, color, and luster. Preliminary study of Calcareous nanofossils in one crust shows that the crust began to grow since Paleogene. The porous middle layer was formed from late Miocene to late Pliocene (Ca. 0.5 ~ 11.9Ma) and the compact lower layer was formed from late Paleocene to late Oligocene (Ca. 56.3 ~ 23.2Ma). The sedimentary hiatus of a 14.26Ma was observed between the middle and lower layers. The boundary between them to be Oligocene/Miocene (O/M) shows an important message on growth age.

By Steven D. Scott

The source of ore metals for base and precious metal volcanogenic massive sulfide (vms) deposits has been debated for decades. Metals can be obtained from high-temperature sea water-rock reactions in subseafloor circulatory hydrothermal systems, or provided by the magmatic fluids that are degassed from magma. The magmatic signatures are largely erased in the hydrothermal system by the overwhelming, long-term circulation of seawater. Melt inclusions in phenocrysts (plagioclase, olivine, pyroxene) of volcanic rocks provide an effective means of understanding the potential for a magmatic contribution to the ore-forming fluids. We present results of a melt inclusion study on the volcanic rocks that host active seafloor hydrothermal fields in the eastern Manus immature back-arc pull-apart basin of Papua New Guinea and an Ordovician-age back arc in New Brunswick, Canada that hosts the ?giant? (330 mmt) Brunswick #12 vms ore deposit. A fluid phase is typically observed in cavities within melt inclusions, indicating that the magma was saturated with volatiles prior to its eruption. The fluid is CO2-dominated with lesser H2O and CH4 in melt inclusions of mafic volcanics and is H2O-rich in felsic volcanics. Tiny crystals and amorphous precipitates (recrystallized at Brunswick #12) of Fe, Ni, Zn, Cu and Mn chlorides, sulfides and oxides coat the walls of the vapor cavities. The crystals include magnetite, magnesite, calcite, anhydrite, gypsum, barite, pyrite, chalcopyrite, halite, silicates and apatite. At Manus, the compositions of the precipitates on the bubble walls of melt inclusions are similar to those found in the vesicles in the matrix glass of the same sample. The ore metals in the volatile phases changed from Ni+Zn+Cu+Fe ? Cu+Zn+Fe ?Fe+Zn (+Pb?) as the magma evolved from basalt, basaltic andesite ? andesite, dacite ? rhyodacite, rhyolite. Glass of the melt inclusions compared to that of the matrix of the rocks from Manus have significantly higher concentrations of H2O (av. 1.64 vs 0.7wt%), Cl (av. 2500 vs1300 ppm) and S (av. 900 vs 100 ppm) suggesting that these volatiles were extensively exsolved from the magma. A minimum of 1.0 to 1.7wt% of magmatic volatiles is estimated to have been degassed before and during the eruptions. The focused discharge of a magmatic fluid as a result of pre-eruptive degassing could be responsible for the metals in the sulfide deposits on the seafloor. If 1 km3 of magma were emplaced in a shallow chamber, then the associated magmatic fluid would be 35.1 million tonnes. If this fluid contained 2.3 wt% Zn and 7.2 wt% Cu (Yang and Scott, 1996, Nature), a total of 0.8 million tonnes of Zn and 2.5 million tonnes of Cu would be to the hydrothermal system.

Jan 1, 2005

By Henk van Muijen

From an interesting and intriguing scientific research topic, deep sea mining has altered into an interesting mining prospect over the last years. Ten years ago most of the focus was on geological investigations, searching for typical deep sea deposits and getting answers on where we can find them and how these deposits were formed. At this moment we know much more about the interesting deposit possibilities and with our quest for minerals, metals and other materials to feed global economic growth, answers as to the technical and economic feasibility to mine these deposits are sought. This is not a new phenomenon as we already witnessed such question late 1970?s and early 1980?s. Most of the focus was on mining manganese nodules and brines in the Red Sea driven by the report of the Club of Rome that predicted shortages in near future at that time. Development went different, but later in the 1990?s a rival of interest could be noticed for mining deep sea deposits.

Jan 1, 2010

By G. Rehder

The release of methane as free gas from the seafloor into the water-column well within the hydrate stability field is a natural process observed today in various ocean settings, such as the Cascadia margin, the Black Sea, the Guayamas Basin, and the Gulf of Mexico. The subsequent dissolution of gas bubbles into the water-column determines the vertical distribution of aqueous methane in the water-column and the upwards methane flux. Understanding this process not only is essential to describing the impact of natural deep-sea gas seepage, but also to assessing the hazard potential from blowouts and offshore exploitation activities, which are steadily expanding to greater ocean depths. Furthermore, the fate of methane from seeps contributes to scenarios of global change in the past and future involving the large scale destabilization of gas hydrates on a. We recently reported on the extended lifetime of methane bubbles within the hydrate stability field due to the formation of a hydrate skin (Rehder et al., 2002), based on in situ measurements of methane and argon bubble dissolution in the depth range 400 to 800 m. More recently, these observations were extended to depths from 900 to 1500 m. Single bubbles were injected from the ROV Ventana into an attached, back-illuminated, flow-through imaging box. The ascent of individual bubbles within the imaging box was recorded with Ventana?s HDTV camera system by piloting the 3-ton ROV upward, at the bubble rise velocity, for up to 400 m of vertical transit. Observed rise velocities were approximately 30cm/sec for all depths. Post-dive analysis of the HDTV video allowed detailed measurements of the bubble shrinking rates. The results of the earlier and new experiments lead to the following conclusions: (A) Methane bubbles released below the hydrate stability field showed markedly enhanced lifetimes, attributed to hydrate skin formation. The change in radius with time, dr/dt, varied from -7.5 micrometer/s above the hydrate stability field to about -1 micrometer/s at the deepest release depth. (B) Bubble lifetime within the hydrate stability field increased with distance in P-T space from the hydrate phase boundary. (C) Before hydrate skin nucleation, dr/dt for CH4 bubbles was comparable to dr/dt above the hydrate stability field. Although variable, the onset time for the hydrate skin effect to occur generally decreased with distance from the hydrate phase boundary (super-pressurization and super-cooling with respect to hydrate formation). (D) Even before the onset of the hydrate skin effect, a slight decrease of dr/dt with increasing depth was observed.

Jan 1, 2005

By Richard C. Newell

The United Kingdom marine aggregate mining industry is the second largest of its kind after Japan. Materials for the construction industry, sea defences and for many other purposes are exploited from shelf waters at depths of 30-50 metres by self-contained suction dredgers which often screen material to obtain a cargo of a particular quality. Assessment of the environmental impact of such mining activities both within the boundaries of the dredged areas, and in the zone of deposition of outwash from the dredger has in the past been mainly based on predictive models based on the settlement rates of the individual particles and assumed Gaussian diffusion principles during the settlement phase. Recent studies which we have made on both the mass balance for materials rejected during the dredging process and direct measurements of the settlement of material in the dispersing plume suggest that the zone of settlement is much less than that predicted from diffusion models. Instead of a downstream settlement plume of 10-20 km in the tidal currents of U.K waters, our measurements show that inorganic components of the dredger plume reach background levels in the water column within 880 metres.

Jan 1, 2000

By Tony van der Steen

Subsea mining system are designed for the following, principally different, tasks: Dreding - The destruction and removal of seabed sediments overlaying the bedrock. Cleaning - The competence of the system to systematically remove the deposits from an undulating hard bedrock with irregular pulleys, channels and fissures. Factors that influence the choice of dredging equipment for a specific project are project requirements such as environmental conditions, location and water depth. However, the most important selection criteria are soil conditions. As a consequence, possible dredging systems, must be evaluated for the following, principally different, characteristics: Dredging proficiency - The destruction of the strata by the equipment. System stability - The capability of the soil to support the subsea equipment The above parameters are determined by the strength characteristics and the bearing capacitv_ of the soil. The author describes the processes involved in excavating the subsea deposits and (transporting the gathered soil as a water-soil mixture to the surface using different excavation and transport methods.

Jan 1, 1998

By N. J. Poll

The Zacarias gold-silver-barite deposit appears to be a Precambrian analogue of present-day exhalative deposits on the sea floor. Geochemical, stratigraphic and structural studies of the latter can be useful in elucidating the ore environment at Zacarias, thereby assisting exploration. The Zacarias mine is about 300 km north of Brasilia, within the Goiás Massif, Brazil. It is the southernmost of three auriferous quartzite occurrences along 1 km of a northeasterly striking amphibolite. Zacarias and its neighboring smaller deposit to the north, the Central Pit, contained a premining ore reserve of 650,000 tons at 4.4 g/t gold, 48 g/t silver, and about 20% barite. Gold mineralization is hosted by concordant quartzite strata also containing layered barite, pyrite, barium-mica, sphalerite, galena, chalcopyrite, magnetite, sulfosalts, free gold, and electrum. The host amphibolite is intercalated with barren mica-quartz-chlorite-pyrite schists that are more voluminous in the footwall and are associated with the ore horizons. Above the amphibolite in the hangingwall lies a thin graphitic shale, then a feldspathic arenite. The strata and regional foliation strike northeast and dip 42° northwest. Crenulation and small-scale folds plunge 30 to 40° to the west.

Jan 1, 1993

By Wiebe Boomsma

This is a framework study financed by the Maritime Innovation Programme of The Netherlands and several institutions actively involved in the research of the environmental impact of deep sea mining; IHC Mining, MTI Holland, Delft University of Technology, NIOZ, IMARES, Boskalis Westminster, AllSeas and TNO. For this framework study the following mining activities have been identified to be relevant to assess the ecological impact of a deep sea mining operation: a) excavation, b) tailings return, c) vertical transport, d) vessel operations, e) ore transport and f) general operations. For this paper, only one mining activity has been selected as an example for the assessment of ecological effects. This is one of the main activities introduced by the new technology envisaged for developing deep sea mining: tailings return.

Sep 14, 2011

By Michael J. Cruickshank

A workshop to examine recovery systems for selected strategic and critical materials in the U.S. National Seabeds for the National Defense Stockpile in the 21st Century was held in Hawaii September 26-28, 1991, sponsored by the National Science Foundation and the Marine Mineral s Technology Center. The National Defense Stockpile of critical and strategic mineral commodities is presently in a deficit position of more than 7.5 billion dollars. Current domestic reserves of some commodities are limited or nonexistent. As defined by the U.S. Bureau of Mines, "Reserves are select resources . . . which at the time of classification, can be mined at a profit." Occurrences of these minerals have been discovered offshore within U.S. jurisdiction. If the technology could be developed to convert these resources into usable ore reserves, our dependence on foreign ores could be greatly reduced. Preliminary estimates indicate that a ten-year program of ore reserves definition, with appropriate technical developments to demonstrate a recovery system, could cost less than half the amount authorized for stockpile acquisition in FY 1989 alone.

Jan 1, 1991

By Brian Parsons

In June of 2013, Odyssey Marine Exploration conducted sea trials of the newly installed SeaBat 7150 full-ocean multibeam sonar system on the M/V Dorado Discovery over the Fierberling Guyot in the northeast Pacific Ocean. Fieberling Guyot is located approximately 990 kilometers west of San Diego, California and it rises abruptly from the deep ocean floor (~4300 meters) to a minimum depth of approximately 438 meters. The SeaBat 7150 operates at two distinct frequencies, 24 kHz (shallow to 3000 meters) and 12 kHz (full-ocean depth greater than 2000 meters). Onboard operational data are managed by a suite of state-of-the-art software. A SQL Server 2012 database provides the highly specific management and visualization tools as ArcGIS 10, Micromine 2013, and Geobank 2013 database. The 7150 is mounted on a gondola one meter lower than on previous system and greatly reduces bubble interference. The 7150 generates 880 beams

Sep 14, 2011

By James R. Hein

Manganese nodules from the Cook Islands (CI) Exclusive Economic Zone (EEZ) are compositionally different from other nodule fields. CI nodules have relatively high cobalt concentrations and low nickel, copper, and manganese concentrations (e.g. Hein and Petersen, 2013). This reflects the predominantly hydrogenetic (seawater source) origin for metals in the CI nodules versus dual seawater-pore water sources for most other nodules. The concentrations of many critical and strategic metals have not been previously analyzed for CI nodules, so comparisons with other nodule fields have been limited. To address this, we analyzed a set of nodules distributed throughout the CI EEZ for a complete set of 67 elements, including all of the metals that may be of economic interest, such as the rare earth elements (REEs), yttrium, tellurium, niobium, zirconium, tungsten, titanium, and others (see selected elements in Table 1). In addition, we recalculated the tonnages of nodules and contained metals from nodule abundance areas (in square kilometers) determined by GIS ArcMap calculations based on JICA/MMAJ (2001) nodule distributions. The nodule tonnage calculated and summed from each abundance sector yields a total inferred resource estimate of 9.66 billion tonnes of nodules covering an area of 1.21 million square kilometers; using a cut-off of 6 kilograms of nodules per square meter, yields a median tonnage of 8.59 billion tonnes of nodules covering 687,647 square kilometers (Table 2).

Sep 14, 2011

By Peter Halbach

The two HYFIFLUX cruises of the German RV SONNE (SO 99/1995 and SO 134/1998) were organized in the framework of a co-operation between several German universities and two European marine research partners. It is a multidisciplinary program for the study of hydrothermalism with its associated geological, mineralogical, and biological processes in the North Fiji Basin (NFB) in the SW-Pacific. The main achievements of the HYFIFLUX cruises were detailed multibeam Hydrosweep mapping in order to identify the detailed tectonic setting, water sampling at hydrothermally active vents, mineral sampling at inactive sites with sulfide, sulfate, and silica mineralizations, and sampling of basaltic rocks, (Halbach et al. 1999). Oceanic accretion in the NFB is characterized by a double spreading system (Auzende et al. 1994),with one spreading axis located in the median part of the basin (Central Fiji Ridge, CFR) and the second one located immediately west of the Fiji platform (West Fiji Ridge). Most of our investigations were done in the northern part of the N 15° segment of the CFR, which corresponds to area A of our program, area D is located farther south in the NFB and corresponds to the N-S segment of the CFR (Fig. 1). During previous works under the French-Japanese STARMER project, the active ?White Lady? mound and the extinct Père Lachaiseí site were sampled; these samples were studied by Bendel et al. 1993. Here an inactive hydrothermal field was studied, where there were many sediment-covered chimneys in various stages of disintegration, (Bendel et al. 1993). However, the area immediately southwest of the nodal circular basin, which is the triple point junction of the medium-spreading Central Fiji Ridge (about 6 cm/yr spreading rate

Jan 1, 2000

By Charles L. Morgan

"In 2012 the International Seabed Authority (ISA) established nine “Areas of Particular Environmental Interest” (APEIs) for consideration as future Marine Protected Areas to help preserve the biodiversity of life on the seabed within the Clarion-Clipperton Zone (CCZ) between Baja California, Mexico, and the Hawaiian Islands. The CCZ is believed to have a high potential for future seabed mining operations. Areas under active exploration contracts in the CCZ, plus the areas currently reserved by the ISA for exploration by developing nations, comprise about 1.9 million km2 of seabed area. The currently designated APEIs consist of more than 1.4 million km2 of seabed. Each APEI includes a central primary conservation area of 200 X 200 km, surrounded by 100-km buffer areas on all sides. The 100-km buffers are intended as a very conservative spacing between the primary conservation area and potential mining activities in adjacent seabed. The selection of these nine 400 X 400 km APEIs, has been criticized as possibly not including sufficient representative habitat similar enough to the potential mining areas (identified currently as the exploration contract and reserved areas administered by the ISA within the region) to ensure protection of the biodiversity that might be impacted by mining.An area to the east of the existing exploration contracts and reserved areas is known to have substantial mineral deposits; it is very similar to the adjacent exploration contract areas in its geology, environmental setting, polymetallic nodule abundance and nodule metal content. Because it is located in the northeastern extreme of the CCZ, this area is also likely to have relatively high densities of benthic life, compared with benthic communities further westward within the CCZ. Many options for the designation of this APEI are possible, but the area designation must accommodate the boundaries of the Exclusive Economic Zones of Mexico and France.This paper discusses why the selected region in the eastern extreme of the CCZ is a good candidate for designation as a new APEI.Keywords: polymetallic nodules, Marine Protected Areas, Clarion-Clipperton Zone, Areas of Particular Environmental Interest"

Jan 1, 2017

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamaji, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamajim, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Irina Melekestseva

The Cu-Zn massive sulfides from the basalt-hosted Semenov-2 hydrothermal field (13°31.13´ N, 44°59.03´ W, MAR) are enriched in Au (22?188 ppm) and Ag (127?1787 ppm) [Ivanov et al., 2008] and elevated contents (ppm) of Se (269?289), Sn (123?125), and Sb (72?75). These may indicate heterogeneous substrate rocks and possible ultramafic rocks. Based on phase analysis, 70% of the gold in the massive sulfides is free. LA-ICPMS analysis has shown that the main carrier of the invisible gold is covellite (22.51? 226.64 ppm). Covellite is also characterized by elevated contents of Se, Mo, Sn, Te, Au, Bi, As, Ag, Sb, Tl, and Pb relative to the primary sulfides.

Sep 14, 2011

By Tao Chunhui

The seabed deposits type and distribution are very complex at the hydrothermal field. In this paper, we provided an approach to study the seabed deposits classification at the Precious Stone Mountain hydrothermal field (PSMHF) using MultiBeam sonar data . The PSMHF was found in the Galapogas microplate at the Leg 3 of the Chinese COMRA 21st Cruise. Using this approach, the seabed deposits at the PSMHF are mainly classified into three types, which are rock, breccia and sediment, respectively. We can find the distribution of the three types of seabed deposits according to the sonar backscatter data. The rocks are mostly distributed around the hydrothermal vent. The breccia are located at the foot of the vent. Most sediments are distributed at the southwest to the vent due to bottom current. Combining with seabed video, TV-Grab sample and the backscatter data, we draw the map of the seabed deposits distribution at the PSMHF.

Sep 14, 2011

By Sven Petersen

The southern Mid-Atlantic Ridge (SMAR) is one of the least-explored spreading centers in the world with respect to hydrothermal activity. In the past 8 years research focused mainly on the ridge segments close to Ascension Island, discovering hydrothermal fields as far south as 14°20?S (Haase et al., 2007; German et al., 2008; Tao et al., 2011). However, the vast majority of the SMAR ridge axis has never been thoroughly investigated for hydrothermal activity. In the spring of 2013 we used segment-scale AUV deployments as well as conventional CTD surveys to identify areas of hydrothermal activity along 16 mid-ocean ridge segments between 13° and 33°S, thereby covering close to 5 % of the global ridge axis in a single cruise. During cruise MSM25 of the German research vessel Maria S. Merian, we tested longrange (>100 km lines per dive) AUV deployments of GEOMAR?s AUV ABYSS (a Remus 6000 vehicle) along the spreading axis for their capability to locate active venting in a fast and efficient way on regional surveys. Since the missions covered long distances,

Sep 14, 2011

By John Parianos

2013 has seen good progress for Nautilus Minerals and our projects due to the determination of our people and the continued support from shareholders and stakeholders. Our focus remains Solwara 1 in Papua New Guinea for which the build continues on the seafloor production tools, subsea slurry pump and riser and lifting system.

Sep 14, 2011