Search Documents

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By George G. Goble

The use of augercast piles has been limited by the engineer's concern for the structural quality of the installed pile. The nature of the pile is such that its final structural continuity is very dependent on the skill of the personnel that do the installation. Thus, NDT methods have been used to verify integrity and when problems are indicated the available solutions are usually quite costly. If information were available during the pile installation so that immediate steps could be taken to correct perceived problems, the concerns of the engineer could be addressed and the system would gain increased reliability. Pile Dynamics, Inc. has developed a quality control system, the Pile Installation Recorder for Augered Cast-in-Place piles (PIR CFA). This system consists of the following devices as shown in Figure 1. 1) The Control Unit powers the sensors, conditions the signals from the sensors, records all measurements, takes input information from the operator, displays the results, and stores the recorded data on a flash card for later permanent storage and processing. During the use of the system all of the results obtained during a test are seen during recording and can be reviewed on the screen again after completion of the installation. The ability to review the measured information makes it unnecessary to print a copy in the field. Since printers often give difficulty in the construction site environment the ability to review the results quickly after completion of the installation is an important capability.

Jan 1, 1997

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By Liqun Liang

Various nondestructive testing (NDT) inspection methods are available to evaluate the structural integrity of cast-in-place shafts. The widely used methods include Cross Hole Sonic Logging Testing and Low Strain Testing. Due to its advantages such as low cost, easy operation, quickness and flexibility (no need to plan ahead and prepare inspection tubes or other devices), Low Strain Test is frequently specified in quality assurance programs of many countries or when doubts arise as to the integrity of the finished shafts/piles. The method is well suited for small to middle sized shafts. However it is an indirect NDT testing method and has certain limitations. Data interpretation requires proper training, experience and judgment and, therefore, inconsistent conclusions and reporting may be provided by different testers. To avoid or reduce such inconsistencies, it is best to follow a standardized data interpretation and record classification system. In this paper, a new classification method is presented with examples. A step-by-step data evaluation and interpretation procedure is proposed with examples of real cases to help understand the LST data. The paper also makes recommendations for measures to be taken when anomalies are detected in tested production piles.

Jan 1, 2011

By Matthew Janes

Statnamic load testing is becoming widely accepted as a method to quickly and economically determine the load-deflection behaviour and ultimate static resistance of high capacity deep foundations. Strain instrumented large diameter bored shafts were tested at four locations for the federal and state Departments of Transportation in the United States. Tests were conducted vertically (to 30 MN) and laterally on the shafts and, in some cases, testing was completed over water. Instrumented shaft test results provided shaft load distribution with depth and shaft shear transfer stress throughout the soil stratum. Shaft end bearing and ultimate end bearing stress values were provided. On two projects, Osterberg load cells provided comparative static data for skin friction and end bearing. Correlations between Statnamic derived static load-displacement results and Osterberg load-deflection results are very good. Statnamic lateral load test results were correlated with static lateral results in addition to providing useful dynamic response and damping data.

Jan 1, 1996

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Mait Mets

In Estonia, the deformations monitoring of 1500 buildings are currently under investigation, buildings on pile foundations make up 10 per cent of these. In the following text we will be considering the behaviour of pile foundation buildings in various parts of Estonia, in differing geotechnical conditions.

Jan 1, 2002

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By Masaki Kitazume

Deep mixing method, in-situ admixture stabilization technique, has been developed and adopted for on land and marine construction works in Japan. The geotechnical design procedure of the method has been standardized in Ministry of Land, Infrastructure and Transport Government of Japan for port and harbor facilities, which includes the block type and wall type improved grounds for foundation stability, settlement reduction purpose. This procedure is based on the allowable stress concept, in which the induced stresses within the improved ground are confirmed to be lower than the allowable strength in the internal stability calculation. This procedure has been cited by several organizations to establish their standards. The Ministry has a plan to introduce a reliability based design for marine construction works in 2006, in which the design procedure on DM improved ground will also be modified to the reliability based. In the new design procedure, the average and variation of soil parameters and external loads are incorporated by partial safety factors to investigate the stability of improved ground. According to the plan, the author has been studied the design procedure and the magnitude of partial safety factors, and has established a preliminary draft of the standard. This draft will be brushed up through comparing the current design procedure. In this article, the design concept and design procedure of the method are briefly described.

Jan 1, 2004

By Derrick D. Dasenbrock

Three piers of a new river bridge are supported on 1.067 m diameter open-end steel pipe piles. At time of drive, and after pile re-strikes, high-strain dynamic capacity values at plan tip elevations, were as low as 23% of design requirements. Pile lengths were extended 20% to 40% deeper than planned at two piers, driving to rock, impacting both the project cost and schedule. The significant discrepancy between predicted and observed capacity was investigated through a series of coordinated dynamic tests; a full-scale test pile was installed and monitored over 221 days by both dynamic and quasi-static methods. Unusually slow strength gains were observed by dynamic monitoring on all piles installed at the site. CPT soundings were advanced at the test pile and through the pile interior to investigate the soil plug. High-strain dynamic methods were found to have significant limitations in properly assessing the long-term capacity of large-diameter open-end pipe piles during driving and short-term pile re-strikes. As the benefits of large diameter high-capacity open-end pipe piles are numerous, the geotechnical community needs to address appropriate construction monitoring and control of these foundation types to take full advantage of these systems. An improved understanding of the physical effects of pile installation and the impact on soil strength assessment while driving and long term soil strength gain should be developed and incorporated into both design and monitoring procedures to avoid either unsafe or needlessly costly designs.

Jan 1, 2006

By Inn-Joon Park

Major problems associated predicting soil-structure interaction behavior are based on the fact that soil is neither homogeneous nor elastic and soil properties are spatially variable. There also exist significant coupling problems between the behavior of the structure and geologic media. When designing foundation or other geotechnical structures, the load transfer between the soil and structure takes place at the contact surface. This surface is called the interface. The behaviors of interface play an important role in the load-deformation response of soil-structure interaction systems. The purpose of this study is to develop improved model for simulation of saturated sand-steel pile interface behavior based on a general concept, called the disturbed state concept (DSC), which can characterize the behavior of saturated soils under dynamic loads. In this study, the Disturbed State Concept (DSC) constitutive model is calibrated and modified for steel pile-saturated sand interface and interaction by using the continuous hardening model for relative intact (Rl) state and the critical state model for the fully adjusted (FA) part in the saturated sand material. The general formulation for implementation has been developed. Then, the DSC model with modification for interface and saturated sand is implemented in finite element program based on the generalized Biot's theory. The interface tests under one-way monotonic and two-way cyclic loading and cyclic triaxial tests are executed for defining the parameters for interface and surrounding soils. Based on these parameters, steel pile-saturated sand interface and interaction are numerically simulated using the finite element program modified in this study. The DSC predictions show improved agreement with the observed results from laboratory test.

Jan 1, 2002

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By Pete Howell, Patrick Granitzki, Alicia Plinio, Janitha Batagoda

The New York City Housing Authority (NYCHA) Red Hook Houses was subjected to damage during Superstorm Sandy. As a result, the NYCHA has an ongoing project known as Restoration Associated with Sandy Recovery Program to improve the resistance against future storms. The specific project included 28 residential buildings and several service buildings within the Red Hook Development. The subsurface conditions within the eastern portion of the site included existing fill material underlain by varying stratums of very loose, loose and medium dense silty sands followed by very soft to medium stiff clay or dense silty sands. The western portion of the site included existing fill material, very loose to medium dense silty sands and organic clayey silts underlain by very soft to medium stiff sandy silts. Based on the geotechnical report, a conventional driven steel pile system was specified containing two pile depths. As part of the project bidding, an alternative pile type was recommended and analyzed to provide quicker installation, reduce vibrations, reduce noise, and provide relatively large cost savings. Due to relatively high lateral loading, an innovative double steel casing drilled displacement piles was proposed as the alternative pile option. Field testing proved the piles capable of the required project capacities and the use of drilled displacement piles as the best alternative for the project and accepted by the NYCHA.

Oct 1, 2022

By Maurizio Siepi

The realisation of most of the civil engineering works is subordinate to the execution of consolidation works, in order to improve the soil physical-mechanics characteristics. The works classifiable with the term "Soil Improvement" can be realised using several technologies, among which the Deep Mixing Method is distinguished for his remarkable flexibility and productivity characteristics. The Deep Mixing Method is a process whereby a rotary drilling machine mechanically drills a constant diameter hole while cement slurry is injected into the soil at high pressure. The process combines state of the art construction techniques merging mechanical and hydraulic mixing energies at the tool bit. The result is a soil-cement column of engineered strength, consistency and dimension. Whereby the soil cement column formation process is controlled by a computerised device, the result is a speedy installation, thorough mixing, and a high degree of control, repeatability and documentation.

Jan 1, 2002

By Edmund J. Cardoza

WELCOME TO THE DEEP FOUNDATIONS INSTITUTE 26TH ANNUAL CONFERENCE AND WELCOME ESPECIALLY TO THIS SEMINAR ON NON-DESTRUCTIVE TESTING OF DRILLED SHAFTS, PRESENTED BY MEMBERS OF THE DFI DRILLED SHAFT COMMITTEE. MY NAME IS ED CARDOZA; I AM A VICE PRESIDENT WITH THE MILLGARD CORPORATION, A DRILLED SHAFT CONSTRUCTOR FOCUSING PRIMARLY IN THE EASTERN HALF OF THE UNITED STATES.

Jan 1, 2001

By Gordon Demetrick

3900 Yonge St. was not a typical site on which to build a condominium apartment. A steep hill covered the majority of the site. In order to use as much of this site as possible, the rear of the building was to have nine stores cut into the face of the hill. A permanent shoring system was required as the building structure was not designed to provide sufficient stabilizing elements to support the total earth pressure. The total excavation depth required was 36 m (120'-0") with the upper 12 m (40'-0") to be backsloped. The vertical face of soil to be supported was 24 m (80'-0'). The shoring system originally designed by the Structural Engineer was to support this face by installing soldier piles and inclined earth anchors. During bid preparation it became evident to us that the system as designed would be difficult and expensive to install due to wet soil conditions. An innovative design was required to overcome these problems. Anchor Shoring hired John Stephenson Consultants Ltd. to aid them in accomplishing this goal. After extensive investigation together with The Trow Group, a unique design was proposed which provided a practical solution to the shoring problem.

Jan 1, 1987

By Anjana C. P, K. Ranga Swamy

The hilly regions of Kerala are severely affected by excess rainfall, causing tremendous damage due to landslides and slope failures. It is necessary to strengthen the existing slope profiles to prevent such disasters and avoid their risk to human lives and civil infrastructures. This paper studies the effect of micro pile to reinforce the slopes in Idukki district of Kerala, where slope failures are frequent. Three-dimensional slope stability analysis is carried out on slopes from the Idukki to obtain safety factor values using the MIDAS GTS NX program. The slope is fully saturated herein by taking the model's piezometric surface at the ground level to simulate high rainfall intensity. The critical slopes are then modelled with micro piles to analyze their effectiveness in improving the stability under static conditions. Different micro pile arrangements are considered, and a series of slope stability analyses have been carried out to obtain the optimum configuration with the required safety factor. The FOS values increased by more than 50% with micro piles for all the slopes. The optimum micro pile arrangement obtained for each slope shows that micro pile distribution between the toe and middle of the slope is an effective location for reinforcing slopes.

Sep 1, 2022

By Craig T. Jones, Zachary Q. Maassen

"Jet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. Data from projects completed in Toronto and Ottawa is presented where BOS Solutions’ services provided significant savings compared to the traditional spoils treatment utilizing vacuum trucks for spoils disposal. These traditional treatment methods are cumbersome and expensive by nature. BOS Solutions provided an alternative solution that is environmentally friendly and capable of handling full flow to process these jet grout spoils utilizing a tank system paired with centrifuges and flocculation additives to remove the ground soils and grout product from the spoils slurry. BOS’ process produced a clean water for reuse in the project while reducing the overall waste volume by producing a dry, stackable solid that could be hauled to a landfill. Benefits observed by using the BOS process were disposal waste volumes decreased over 30% and at least a 19% reduction on disposal costs.SCOPE OF WORKJet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. The backflow, or spoils, is a mixture of grout, water and soils. Traditionally, the spoil would be collected in in-ground pits and allowed to solidify for a few days prior to hauling to a final disposal site. For the projects completed in Toronto and Ottawa, the jet grouting work was performed at street level, in high traffic congested areas, presenting the challenge of insufficient space for the contractors to process the jet grout spoils in the traditional way. At first, attempts were made of using vacuum trucks to collect and haul the wet spoils to an off-site location where the spoils would be allowed to solidify. However, this method proved cumbersome and expensive due to the high volumes of spoils generated daily and the high number of vacuum trucks required to support the jet grouting operations, respectively."

Jan 1, 2017

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022