Search Documents

By J. B. Kwon

For improvement in the productivity of tall building projects, table formwork is one of the main methods that have been adopted for slab formwork. Because the table formwork method is an equipment-oriented construction method, the type of lifting equipment and method of operation considerably affects the productivity and cost of the table formwork. It is also important to make an equipment input plan for completing the table formwork within the time given, according to the structural construction cycle. For performing the table formwork, a tower crane or an independent lifting system, and shifting trolleys, are required. However, if an inefficient equipment input plan is made, exorbitant cost may be incurred. Therefore, the purpose of this study is to analyze the productivity of a table formwork, considering the type and number of lifting equipment and the number of trolleys inputted, and to suggest quantitative data for making a cost-efficient equipment input plan within the construction duration given. It is expected that the results of this research will be utilized as a basis for cost-efficient equipment input planning.

Aug 1, 2013

By D. Atkinson

"Porphyry molybdenum-tungsten mineralization on the east flank of Hudson Bay Mountain crops out over 5 km2 and is intersected to depths of 2 km. Features such as a hornblende-biotite aureole, mineralogical zoning and dike, vein and fracture geometries within lithologies of the Middle to Lower Jurassic Hazelton Group and Cretaceous Skeena Group reflect an intrusive complex, the Upper Cretaceous to Early Tertiary Hudson Bay Mountain stock which has been intersected by drill holes. The stock is believed to be the mineralizing agent. A southeast-dipping granodiorite sill has been outlined by drilling within the Hazelton Group. Molybdenite and scheelite veins cut all rock types; however, the granodiorite sill hosts a higher density of fine-grained, banded, quartz-molybdenite and pegmatitic quartz-molybdenite veins reflecting a competency contrast between the intrusive sill and other country rock. Due to the relative abundance of these veins, grade is higher within areas of the sill. Above the 15000£ cross-cut 20.6 million tonnes grading 0.401% MoS2 and 0.041% W03 have been defined. During exploration of the deposit sampling procedures had to be adjusted because of the nugget effect attributed to drill intersections of banded and pegmatitic veins.IntroductionMolybdenite was discovered in outcrop at the foot of Kathlyn Glacier on Hudson Bay Mountain and first reported by the Geological Survey of Canada in 1944. The deposit has several names: Hudson Bay Mountain or Glacier Gulch, both after its location, and Yorke-Hardy after the original staker.The deposit is on the east flank of Hudson Bay Mountain, 9 km northwest of Smithers, west-central British Columbia, within NTS area 93L/14 (54° 49' North, 127° 18' West, Fig. 1). Hudson Bay Mountain, on the southern edge of the Bulkley Valley, is a dominant topographical feature reaching 2590 m elevation. Mineralization is partly overlain by the Kathyln Glacier which is visible from Highway 16. Access to the 3100 m of underground development is from a portal at 1066 m elevation on the east slope of Hudson Bay Mountain."

Jan 1, 1995

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By Ming’an Wei, Qifu Duan, Jianmin Wu, Lusheng Zhou, HMR Group Limited / HMR Technology Canada Ltd., Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company Skega first introduced rubber magnetic liners, and then followed by the Chinese invention of metal magnetic liners. Traditionally, both liners were used in secondary ball mills and regrind ball mills for industrial applications, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged steel balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design. Due to the development of larger diameter ball mills and thus larger ball charge diameter (up to 80mm) especially in non-ferrous metal mining operations, the application of magnetic liners have been very limited. Based on “Magnetism theory” and the development of new materials, the HMR Group Limited has been conducting researches on examining the structures of magnetic liners, associated materials and magnetic circuits which led to the invention of the Nano Alloy Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5 m diameter × 6.5 m ball mill at the Erdenet Copper Mine in Mongolia. The NSML successfully handled a ball size up of to 80 mm, while achieving a service life of nearly 24 months, which is almost 3 times wear life of the original manganese steel liners.INTRODUCTIONDuring the development and utilization of mineral resources, mineral processing is an indispensably operation. The effective separation of various useful minerals depends on sufficient monomer dissociation of minerals in the ores. The crushing and grinding operation is prior operation of mineral processing. Ball mills are used in different concentrators. As the main consumption parts of mill, liners have been studied constantly. As a new kind of liners, magnetic liners besides can meet the requirement of production, and also have characteristics with maintenance-free, saving energy and increasing efficiency. So the magnetic liners are worth to be spread and applied world widely."

Jan 1, 2016

By M. Narita, S. Nakayama, M. Fujihara

Hibi Kyodo Smelting Co., Ltd. was founded in 1968 and celebrated its 50th anniversary in 2018. In 1972, we started producing copper cathode with a production capacity of 84 KTPY. Since the company founding, we have undertaken seven expansion projects, and our current copper-cathode production capacity is 290 KTPY. To increase our production efficiency, two tank houses were converted from Conventional process to ISA process in 2006 and 2014. In another investment, we equipped a continuous glue dosing system, which allowed for strict additive-concentration control, yielded quality improvements and reduced the power-consumption rate. Along with an increase in the production of copper cathode, the amount of impurities eluted from the anode increases. To solve this problem, the chelate-resin purification process that was introduced in 1983 was renovated, and impurities could be recovered more efficiently. In this paper, we report various improvements that have been implemented at the refinery since 2000. INTRODUCTION Tamano Smelter and Refinery of Hibi Kyodo Smelting Co., Ltd., founded in 1968, celebrated the 50th anniversary of its founding in 2018. The Tamano Smelter opened its No. 1 tankhouse in 1972, and began operating No. 2 tankhouse in 1984. Thereafter, with continuous production increases and technical improvements, electrolytic copper production was increased from 84 KTPY to 290 KTPY as shown in Figure 1. Table 1 shows the major operating facilities and operation data in 2017.In this paper, details of equipment introduced to continuously dissolve and add glue, various improvements made to the chelate resin process, enhancements made to the crude Ni sulfate process, and another vibrating screen introduced to the copper slime processing flow in accordance with the expansion of copper production capacity since 2000 are reported.

Jan 1, 2019

By Jun Dai

Based upon research findings from several countries, the combination of microwave and mechanical means to break hard rock holds promise for the future. To achieve this goal, it is essential to understand the laws governing strength reduction of hard rock, such as granite, induced by microwave irradiation. Two aspects to consider are: 1) laws associated with the tensile strength of hard rock after microwave irradiation and 2) the sensitivity of different types of rock strengths to microwave energy. In this study, granite with a range of tensile strengths was exposed to microwaves for various time periods to compare the response of rocks with different strength values exposed to the same microwave irradiation. In addition, a method based on hotspots is presented to explain the mechanism by which granite strength is reduced by microwave irradiation. Granite extracted from Qinling Mountain in Shaanxi Province, China is used in the research. ?50 × 50 mm cylindrical granite specimens were exposed to microwaves at a specific power level. The strength values of the heated granite specimens were compared with those of unheated specimens. Through the comparison and analyses, relationships were determined between 1) reduction in granite strength and microwave irradiation time period, and 2) granite strength and sensitivity to a given energy of microwave irradiation. Finally, a mechanism to explain the experimental results is proposed. Research findings will aid in the design of a microwave + machine rock-breaking system for use in rock breakage in underground mines at depth and for future mine applications on earth and other planets. In addition, the experimental approach could be used to test other rock types to further our understanding of rock damage induced by microwave irradiation.

Aug 1, 2013

By Norman R. Ball

"Many people in the mining and metallurgical industries were brought up to embrace Henry Ford's pronouncement that ""History is bunk"" but it is not generally known that the same Henry Ford created and paid for one of the finest technological museums in the Western World. I am aware that many people feel that industry history is something you ask aging executives to do or that history is a clip-andpaste compendium of pictures re-discovered every 25 years or on the occasion of issuing a press release on plant expansion. Moreover, there are many who fear historians as somewhat deranged individuals interested only in corruption, injustice and sensational labour strife. Good history lies somewhere between the controlled P.R. handout and the hysterical attack. Writing good history is a difficult creative act based on the application of experience, insight, wide knowledge and careful reasoning to available evidence. To date, the Canadian mining and metallurgical industries have achieved a great deal but left too little evidence and it is this lack of evidence which must be corrected before it is too late. It is the purpose of this article to stimulate thoughts with regard to archives, one of the more important vehicles for the preservation of such evidence."

Jan 1, 1999

By W. Lin, Z. Z. Dong, C. L. Zhou, Y. C. Kuang

The inversion of rock mechanical properties based on well-logging data is a common method to drillbit selection in petroleum engineering, the basic principle of which is to use deep-well logging data and experimental regression model to calculate rock mechanical properties. The profile of rock mechanical properties can be established. According to the profile, the type of drillbit can be selected in different formations, which will improve the economic benefit of bit use indicators. Compressive strength of rock is one of the most important parameters. Conventional method to establish regression models of acoustic velocity and uniaxial compressive strength is on the basis of rock core sonic experiments and uniaxial compressive experiments. However, with the increase of deep drilling operation, triaxial compressive strength prediction model will play a more vital role in drillbit optimization selection in deep wells and improving ROP (Rate of Penetration). Triaxial compressive strength is an important parameter to evaluate the formation strength property. In this paper, to the sandstone commonly encountered in oil drilling, combined the rock mechanical experimental results with the changing porosity experimental results under confining pressure, a new interpretation model of triaxial compressive strength based on well logging data is proposed. Firstly, three types of sandstone samples are collected. Then measured components, uniaxial compressive strength, triaxial compressive strength and porosity. Experimental results show that: confining pressure has a significant influence on sandstone strength, with the increase of confining pressure, triaxial compressive strength increase; furthermore, the triaxial compressive strength of different porosity sandstones have different change rules when confining pressures changes; sandstone porosity decreases with the increase of confining pressure and it obeys logarithmic function. According to the results, regression models of sandstone, in-situ uniaxial compressive strength model and uniaxial compressive strength model under normal pressure are generated. Meanwhile, using well logging data in the acoustic velocity, density and gamma value can derive in-situ rock formations uniaxial compressive strength and in-situ porosity. Eventually, a new model established in this paper, containing in porosity, uniaxial compressive strength, lateral pressure and power exponent of regression, can predict triaxial compressive strength which will guide drillbit selection.

Jan 1, 2015

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By Yan-Jun Shen

The rock mass classification system, BQ (basic quality), is the only national system that is suitable to most kinds of rock engineering in China. It uses two main aspects of the rock mass, the intact uniaxial compressive strength (UCS) and the rock intactness index (KV), to obtain the rock mass BQ. The index KV could be measured by the acoustic wave method. However, because this method is an indirect approach to characterize the rock mass structure, misfits often occur between the test results and the actual rock mass characteristics. Therefore, a new parameter KGSI expressed by the geological strength index is proposed to replace the original KV, and a new method is presented to express the value of BQ as a function of the UCS and the KGSI. Then, the underground excavations at five hydropower stations were chosen as examples to study the relationship between the revised BQ and the each of the international systems (RMR, Q or RMi). In addition, the applicability of the RMR, Q, or RMi system is discussed for China?s rock characteristics and geological conditions, and suggestions are given for improving the revised BQ system.

Aug 1, 2013

By J. H. Starkey

Large differences between macro and micro grindability relationships have been discovered for mill design measurements using the patented SAGDesign(TM) test. Crushing, Rod and Ball Mill Wi tests, and breakage parameter measurements have previously been used to design SAG mills but have not revealed the true magnitude of these differences. A SAGDesign(TM) test measures the SAG/Bond Wi Ratio (defined below) for every sample tested and gives a good design result because the F80 of the SAG stage test feed is 19 mm and because the test includes a Bond Ball Mill Work Index on SAG ground ore. Good flotation operation demands properly sized grinding mills and steady feed to the flotation circuit.

Jan 1, 2009

By S. Duvah Pentiah

The transformation of an open pit coal mine to a horizontal-punch underground mine is subject to a number of challenges. These include scheduling the operation of various sizes of trucks over a long period, as well as updating delivery routes and dump site locations as the mine transformation progresses. In this process, rock is excavated from a quarry through earthworks. The bulk earthwork and quarry material delivery were initially drawn from traditional planning and experienced issues in their early phases. As a result, a traffic simulator was developed in order to validate schedules and predict achievable throughput, likely delays or blockages in the long term. The dynamic traffic simulator was also used to provide traffic density and vehicle arrival data at selected intersections in order to identify possible safety and efficiency issues.

Aug 1, 2013

By W. L. Ott, C. L. Lewis

"AbstractA technique is described for preparation of palladium sponge and for spectrochemical analysis of the metal in this form. The precision and accuracy of the method are discussed. Analyses are compared with previous spectrochemical analyses of palladium in the black form. Good agreement was found in the two sets •of results and it is concluded that they are more reliable than wet chemical .analyses of the same material.IntroductionFOR SEVERAL YEARS the problem of platinum metal analysis by spectrochemical methods has been under investigation at the Spedtrographic Laboratory, Department of Geological Sciences, Queen's University. The problem, briefly -stated, is as follows: Samples of platinum, palladium,-rhodium, ruthenium, and iridium are received as fine metal powders, called sponge. Direct spectrographic analysis of this material has not been found satisfactory due to its heterogeneity •as regards contaminant metals, which may be present up to a total of one per •cent or more. Further-more, spectrographic standards are difficult to obtain and difficult to prepare accurately by adding weighed portions of contaminant metals to the sponge. The fact that •contaminant metals in original samples are probably alloyed with the major constituent is a further difficulty since complete fusion of these refractory metals proved impractical in the present case as a means of standard preparation. It •has, therefore, been found most satisfactory to dissolve the metals, prepare standards by addition of solutions of contaminant metals, and to reduce both standards and samples to a homogeneous form. A previous paper, by Hawley, Wark, Lewis and Ott (2) dealt with a method for spectrochemical analysis of platinum and palladium in their black form. Since completion of research on the black technique, the possibility of analyzing palladium accurately in its sponge form has• been investigated."

Jan 1, 1953

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By Ralph L. Rutherford

Geologists or mining engineers familiar with geology are frequently requested by mine operators to give correlation in-formation regarding some mining property with respect to an adjacent area on one at some greater distance. It is the object of this article to mention a few of the difficulties involved in securing this information and to point out some of the salient factors upon which correlation is dependent. In view of the nature of the following discussion, a brief statement of the general character of coal formations .. seems appropriate. Coal formations, by reason of their environment of deposition which is in fresh or brackish water, exhibit the features common to continental deposits, in contrast to those of marine deposits. Such deposits are characterized by rapid variation in thickness and in lithological character both later-ally and vertically. (Plate 1 A). They consist essentially of sandstones and clay shales with all gradations between them, and also a few beds of coal and frequently some conglomerates.

Jan 1, 1924

By A. W. Jolliffe

DESPITE the widespread occurrence of scheelite in Canada, domestic production of this strategic mineral is still quite insufficient to meet wartime needs. Two difficulties have invariably arisen in prospecting for or developing scheelite deposits: scheelite is a difficult mineral to identify, and secondly, its distribution is commonly so erratic that the value of a deposit cannot be determined without arduous and expensive methods of sampling and wet assay. Scheelite's property of fluorescing under certain ultra-violet lamps overcomes the first difficulty and is the basis for a quantitative method developed to overcome the second. It is found that, by use of an ultra-violet lamp, the value of many scheelite deposits may be accurately and speedily determined. The method requires neither elaborate apparatus nor exceptional skill on the part of the operator, and is most applicable to those deposits where the bulk of the scheelite occurs in fairly pure aggregates that are at least one-tenth of an inch across. It has been used in grading some two hundred scheelite-bearing veins in the Yellow-knife-Beaulieu region, Northwest Territories, and various occurrences in the Porcupine district, Ontario. The method requires the measurement of the total area of scheelite exposed in any reasonably large measured cross-section of a deposit. From the areal percent of scheelite so obtained, the tungstic oxide (WO,) content of that part of the deposit may be calculated by means of equations of simple derivation.

Jan 1, 1942

By Bahaa Hussein

Considerable number of methods and procedures has been introduced for trending and progress reporting of engineering, procurement and construction projects. This paper introduces a novel method, designed to augment the set of indices for measuring schedule performance. The concept behind the developed method is to provide early warning by dynamically evaluating the schedule cumulative impact of construction projects. The proposed method is designed to highlight the gradual deterioration in schedule status resulting in a cumulative impact due to the aggregation of small delays encountered during the execution of non-critical activities, and can be used as an add-on utility to existing software systems that perform CPM scheduling. The proposed method is based on a developed formulation for quantification of the Schedule Compression Index, which takes into consideration the remaining project activities durations. The index is developed based on periodic comparisons of ?Current Schedules? and the project ?Baseline Schedule? using the summation of the remaining activities durations. A numerical example is presented to demonstrate the application and capabilities of the developed method. It is expected that the developed index together with other schedule performance indices would be of value to decision makers and members of project teams.

Aug 1, 2013

By M. A. Hararah, T. Neesse, M. G. Farghaly, G. Proellss, P. Kaniut, W. Rubarth

ABSTRACT: This paper presents two new options for hydrocyclone control. Volume split control using a control valve in the overflow is applied for the stabilization of separation results at changing feed conditions. Controlled water injection to the conical part of the cyclone leads to the reduction of fine particles in the underflow. Hydrocyclone monitoring in both cases is performed by optical sensors that indicate the spray angle of the underflow. Applications in mineral processing for desliming, classification in closed-circuit grinding, and dewatering are demonstrated.

Jan 1, 2011

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By J. R. Levin, E. J. Schelter

"We present some of our recent efforts in the development of predictive, directed oxidation chemistry of cerium(III) complexes under non-aqueous conditions. The electrochemistry of cerium(III)- alkali metal heterobimetallic aryloxide complexes is reported and compared with cerium aryloxide complexes that are kinetically stabilized by hydrogen bonding cations that span between the complexed aryloxide ligands. Comparative electrochemical measurements reveal differences between the heterobimetallic complexes and the hydrogen-bonded complexes.INTRODUCTIONThe rare earth elements comprise the lanthanides, La–Lu, and the element yttrium (Aspinall, 2001). Rare earth ores such as monazite, LnPO4, and bastnäsite, LnFCO3, typically bear mixtures of light rare earths: La–Sm while monazite, LnPO4, contains mixtures of heavy rare earths (Eu–Lu) (Cotton, 2006). Pure rare earth elements typically are isolated using a liquid-liquid separations process.(Bautista, 1995) The hydrometallurgy of these elements is a difficult problem because the separation factors between neighboring rare earths, which are predicated on the small differences in the sizes of the trivalent ions, are quite small (Cox, 1992). The element cerium, with its 4f1 electronic configuration in the trivalent state, is unique among the rare earth elements due to a relatively accessible 4f0 electronic configuration. The accessibility of the 4f0 configuration underlies the chemistry of cerium(IV), the only rare earth ion with molecular chemistry in the tetravalent oxidation state (Cotton, 2006). Cerium is trivially separated from mixtures of light rare earths by making use of its unique oxidation chemistry. In an effort to extend separations chemistry by oxidation reactions to other rare earth elements such as terbium and praseodymium, the solution electrochemistry of well-defined cerium complexes is of interest."

Jan 1, 2012