Search Documents

By T. Sugawara, S. Hara, Y. Mitsui

Surfaces of rock slopes in cold regions often become frozen in winter. Therefore, understanding time-dependent behavior of frozen rock, as well as that of unfrozen rock, is important for long-term stability assessment of rock slopes. In this study, a series of uniaxial compression tests and creep tests were carried out on Shikotsu welded tuff under dry and water-saturated conditions at -20 °C to clarify timedependent strength and deformation of the frozen rock. The influence of water content on them also was investigated. It was found that the amount of deformation of the water-saturated specimen was much greater than that of the dry specimen. It also was found that the creep behavior of the water-saturated specimen was similar to that of polycrystalline ice. These show that deformation of the water-saturated specimen is strongly affected by pore ice. The UCS of the water-saturated specimen was approximately equal to that of the dry specimen at a strain rate below 4.2×10-6/s, and its value was about 17 MPa. However, the former increased up to 26 MPa at 4.2×10-4/s with loading rate, whereas there was little increase in the latter. This means that the UCS of the water-saturated specimen was always greater than that of the dry specimen at higher strain rates. The creep life of water-saturated specimens was longer than that of the dry specimens at stress level greater than 15 MPa. These results of UCS and creep life show that inclusion effect due to presence of pore ice plays an important role on strength of the water-saturated specimen. Creep life of the non-failure specimen that was loaded for more than three days was estimated by the relationship between creep life and axial strain rate at 10 s on failure specimens. It was found that creep life of the water-saturated specimens was shorter than that of the dry specimen at stress levels less than 14 MPa. This suggests that estimation of creep life of frozen rock under water-saturated condition is important for the stability assessment of frozen rock slopes. It was clear that the loading-rate dependency of UCS was related to the stress-level dependency of creep life in both dry and wet conditions. This indicates that there are common fracture mechanism in creep and uniaxial compression tests. It also indicates that the creep life can be estimated by the relationship between the UCS and the loading rate. The time dependencies of the water-saturated specimen were in good agreement with those of polycrystalline ice. This confirms that pore ice strongly affects the strength of the water-saturated specimens as, well as the deformation behavior.

Jan 1, 2015

By O. Mejia

"As study was undertaken to investigate the relationship between mill liner wear and grinding energy efficiency and to assess the opportunity to control mill speed to improve energy performance as mill liner wears. The study involved analysis of plant operating data and liner wear profiles over time. The operating work index was found to be an effective tool to identify the decrease of grinding efficiency along the liner service. The plant data show that the mill grinding efficiency as determined by monitoring the operating work index, and throughput decreases as liner wears. However, efficiency and throughput can be maintained by either changing the liner more frequently or by increasing the mill speed. Two scenarios for increasing mill throughput were analyzed. The first one involves changing the liner before the efficiency drops and the second one requires increasing the mill speed from 75% to 79%. Both scenarios show financial benefits that can be used in mill operations.INTRODUCTION The analysis of the mill power draw is used in this study as a key parameter for comparing mill liner profile and its effect on mill performance. Current technology and simulation software used in the mining industry do not factor in the impact of liner wear profiles in grinding efficiency and mill throughput (Toor, 2013). To address this gap, this study provides an analysis of key factors affecting mill throughput and grinding efficiency: mill speed, ball loading, and liner profiles. Several years of plant mill operating data, published research papers, and MillTraj® simulation results are used to demonstrate that face angles impact grinding efficiency and throughput and that mill speed can be used to overcome this problem. Moreover, the liner profile wear analyses clarify a mismatch between actual and estimated power draw calculations."

Jan 1, 2019

By A. L. Mackie

Arsenic is a highly toxic element and a known human carcinogen. It is often a contaminant in mine water discharges, particularly from gold mining and roasting operations, and has been found at concentrations as high as 4 g/L. Increasingly stringent controls on the concentration of arsenic allowed to be discharged into the environment cannot always be met by current treatment processes and thus enhanced technologies are required to achieve low treated effluent concentrations at reasonable costs. A novel two-step physicochemical treatment process was developed and tested at the bench-scale using synthetic mine water solutions (SMWs) in order to reduce arsenic concentrations in treated effluent to exceed current discharge regulations. The process includes chemical coagulation with ferric sulphate and ballasted flocculation for enhanced solid-liquid separation. The SMW contained 59 ± 2 mg/L arsenic with a slightly alkaline pH. The effect of arsenic speciation on the process was tested by using either arsenite, As(III), or arsenate, As(V), in the SMW solutions. Tests were performed at cold temperature (3 ± 1 °C) to ensure the process? efficacy year-round in northern climates. Arsenic in As(V) SMW solutions was removed to a final total concentration of 0.0054 ± 0.002 mg/L, almost half the current recommended allowable drinking water concentration of 0.010 mg/L. As(III) was removed to a concentration below the Metal Mining Effluent Regulations? (MMER) current limit of 0.50 mg/L, to 0.32 ± 0.06 mg/L, with double the coagulant dose used in Stage 1 for As(V) removal. Oxidant addition at a concentration of 5 mg KMnO4/L in Stage 2 resulted in final total arsenic concentrations of 0.017 ± 0.002 mg/L and pH adjustment with lime in Stage 2 resulted in 0.0415 ± 0.0007 mg As/L in treated As(III) SMW. Both of these modifications to the process reduced arsenic concentrations to below proposed new MMER limits (i.e., 0.10 mg/L). This two-stage treatment process was shown to reduce arsenic concentrations to well below current treatment guidelines while reducing or eliminating chemical oxidant demand.

Aug 1, 2013

By Jim Cooney

Background ?1990s saw massive changes in South African mining industry ?over 100,000 jobs lost as the industry restructured; ?1999 ?Placer Dome purchased a 50% interest in South Deep (WAL), a mine located just outside Johannesburg ?This was the first major post-apartheid foreign investment in the South African mining industry The Situation ?Placer Dome decided to lay off 2560 mineworkers (one third of the workforce) from the South Deep Mine to restore the mine to economic viability. ?Unemployment in South Africa was over 25%, and the retrenched mineworkers had few skills with which to make a living. Policy Context ?Placer Dome was committed to: ?global corporate policy of Sustainable Development, ?demonstrating that its business contributes to the economic and social progress of host jurisdictions. ?Government of South Africa was committed to ?attracting foreign investment to its mining sector with a view to modernizing and enhancing its economic and social viability, ?ameliorating the negative social consequences of structural change without arresting the necessary process of restructuring. ?National Union of Mineworkers was committed to: ?working with the mining industry and the government in implementing a Code of Good Practice on Dismissals and a Social Plan to assist retrenched mineworkers (1999).

May 1, 2006

By K. Aziz

The solutions to unsteady-state gas flow in a radial system have been reviewed in order to aid in the interpretation of drawdown data. It has been the practice to evaluate the time and rate conversion constants, directly or indirectly, by using reservoir data. This paper presents a method of determining these constants from drawdown data. A simplified approach to the de-termination for the various boundary conditions is presented. An example of a problem which illustrates the use of this theory appears in the appendix. UNSTEADY-STATE FLOW EQUATION The solution of any unsteady-state flow problem involves (1) the continuity equation, (2) the equation of state of the fluid, (3) the equation of fluid motion and (4) the boundary conditions. For the Darcy flow of a gas in the horizontal radial plane, the equation is when the viscosity, compressibility and permeability to gas flow may be assumed constant and the medium

Jan 1, 1963

By V. N. Mackiw, H. Veltman

"A process is described which permits the separate recovery of lead and zinc from complex low-grade sulphide concentrates such as are produced from the New Brunswick type of disseminated pyrite ores. This process calls for the preparation of a lead-zinc bulk concentrate from the original ore by flotation. The bulk concentrate is then oxidized under pressure in autoclaves in aqueous sulphuric acid solution, such as return electrolyte from zinc electrolysis. This yields a zinc sulphate solution and a residue containing lead sulphate, unaltered pyrite and elemental sulphur generated during the oxidation. After the oxidation, the leach slurry is briefly heated to above the melting point of elemental sulphur and then cooled. Thus, pellets containing pyrite and elemental sulphur are formed, and they are separated from the lead sulphate by screening and/or flotation. Laboratory tests have shown that about 95 per cent of the zinc and lead can be separately recovered from complex bulk concentrates. Process possibilities are discussed."

Jan 1, 1967

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By Steven Doyle

Presentation Outline ?Introduction to Brunswick Mine ?Mining Needs and Drilling Trends ?Maintenance Program ?Back to Basics ?Results ?Additional benefits Introduction Xstrata Zinc Brunswick Mine ?No. 12 deposit discovered in 1953, pilot mining 1957, u/g mining began in 1964 ?Zinc, copper, lead and bulk lead/zinc concentrates ?Since 2007, a fully owned division of Xstrata Zinc Canada ?Over 132Mt milled 3.4 % Pb, 8.8 % Zn and 102 g/t Ag ?Deposit dips approximately 70 degrees; strike length of 1200 m; currently mining from 250 m to 1125 m depth

Nov 1, 2011

By Bruce C. Fielder

"The concentration of uranium in orebodies discovered in the Athabasca Basin of northern Saskatchewan over the last 20 years has increased by a factor of 100. These high grade uranium orebodies are associated with high concentrations of radionuclides, complex mineralogy and an elemental makeup that includes base metals, arsenic, and molybdenum. Exploiting these high grade ores has required metallurgical advances in milling, tailings disposal and effluent treatment as well as changes in the design of uranium mills.This paper describes the most significant advances, including advances in dealing with the environmental issues which have become more prevalent in recent years. The milling processes of the Cluff Lake Mill, Key Lake Mill, Rabbit Lake Mill, and McClean Lake Mill are compared to illustrate both similarities and differences necessary for milling different orebodies.BackgroundUranium mining in Saskatchewan started in 1953 when the Beaverlodge Mine, owned by Eldorado Nuclear Limited (Eldorado), came into operation at Uranium City. Development in the Athabasca basin started in 1975 when the Rabbit Lake mine came into operation. This was followed by the start-up of the Cluff Lake mine in 1980 and the Key Lake mine in 1983. The McClean Lake mine is forecast to start up in the near future. The McArthur River mine recently received construction approval and the Cigar Lake Project and the Midwest Project are currently in the environmental approval process.The Beaverlodge operation ceased production in June 1982 after nearly 30 years of operation. The Rabbit Lake mill processed Rabbit Lake ore from 1975 until 1985, Collins Bay R-Zone ore from 1985 until 1993, and is currently processing ore from the Eagle Point mine (Bharadwaj, Jarvi and Lam, 1996). The Cluff Lake mill processed ore from the D- Orebody from 1980 until 1984. Since then the Claude orebody has been processed and the OP and DS orebodies are presently being milled (SRK. Senes and Melis, 1987; and Cogema Resources Inc. 1994 ). The Key Lake mill processed ore from the Gaertner ore body from 1983 until 1989 and Deilmann ore has been processed since (Cameco Corporation, 1992b and I 994a). Processing of McArthur River ore in the Key Lake mill is scheduled for 1999. The McClean Lake mill will be processing ore from the JLR, Sue and McClcan orebodies associated with the McClean Lake mine. In future ore from the Cigar Lake and Midwest projects will be processed in the McClean Lake mill. (Minatco Limited. 1991a)."

Jan 1, 1998

By P. Cleyle, K. McDermott, M. Hall, C. A. Harris

"This paper describes the implementation of an expert system for monitoring and control of the NO. 4 autogeneous mill and spiral circuits at Wabush Mines.This process control system incorporated the mill operating expertize of Wabush Mines operating personnel and was implemented to improve spiral iron recovery and mill productivity by:1. Continuously monitoring the mill power draw and ensuring that the mill feedrate is regulated to prevent damage to the mill motor, while simultaneously maintaining the feedrate at or as close as possible to the maximum feedrate determined by the process supervisor.2. Improving control over the spiral density and feed rate.3. Improving control over both tbe rougher and cleaner wash water.4. Reducing the frequency with which pumps are plugged.5. Allowing modifications to be made easily and quickly to test various operating strategies.This system was installed using COMDALE/C, a real-time Expert System for Process Control. It was readily accepted by the process operators and produces higher production performance in comparison to the other 5 parallel mill lines at a lower power draw."

Jan 1, 1992

By Cris Sideco

This paper describes the concentration processes of the Sullivan. Concentrator, including crushing , transportation, sink-float, grinding , flotation and dewatering. Handling of hot muck has had a deleterious effect on most of the processes, resulting in significant operating problems and poorer metallurgy. These problems are described -in detail. THE SULLIVAN CONCENTRATOR is situated in Kimberley, high up in the Purcell Range of the Selkirk Mountains, at an elevation of 3,600 feet, approximately 4 miles from the Sullivan Mine (see Fig. 1). The original plant went on stream on August 23, 1923 at a designed capacity of 2,500 tons per day. This has been increased in stages to its present rated capacity of 11,000 tons per day. The latest stage was in 1949, when several major projects, including the underground crushing plant, the sink-float plant and the installation of a rod mill, were completed. Some 112,800,000 tons of ore have been treated in this concentrator to November 1975. The plant started on a 48-hour/ week schedule, but was reduced to 44 hours/week in October 1946 and down to 40 hours/week by the end of 1949. Except for a 6-month period in 1952 when the mill operated continuously, the 40-hour/week, Monday to Friday schedule was in effect.

Jan 1, 1977

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By M. Härting, D. T. Britton, M. Nzikou Mamboukou

"Copper containing different types of nanocomposites have been characterized for nanolabelling and ID. Three types of the rare earth nanoparticles were used for this study, the oxide and the sulphur compound of the Eu and Tb. Characterization techniques uses SEM, and Raman for morphology, chemical composition, and optical characterization respectively. It has been shown that it is possible to include the rare earth particle in a copper matrix without damaging its physical properties. INTRODUCTIONThe development of new materials, often involves the addition of new properties without changing the beneficial properties of the original material (Chen et al., 2009; Khana et al., 2007; Patil et al., 2008). Nanocomposites are nanostructured materials, whose structural elements including clusters, crystallites or molecules, of dimensions ranging between 1 to 100 nm (Moriarty, 2001), or a composite material where one of the phases is a one, two or three dimensionally nanostructured material (Nanotechnology, 2006; Wang, 2001). Nanocomposite materials research is a fast growing area due to the high demand for materials for specialized applications (Edelstein & Cammarata, 1998), such as biolabelling, magnetic storage media, solar energy transformation (Jisen et al., 2004), and resistance welding applications (Bessergenev et al., 1997; Kwon et al.,2006).The properties of the nanocomposite materials depend not only on the properties of their individual parent materials, but also on their morphology and the interfacial characteristics. Thus, significant efforts have been focused on the control of the nanoscale structures via innovative synthesis approaches. Therefore, novel materials of unique properties may be obtained by combining properties from the parent constituents into a single material (Balan, 2006; Garcia et al., 2009). Possible effects of nanocomposites in the original material may include changes in the mechanical properties such as hardness , wear resistance (Rafaja et al., 1987), and electrical properties (Britton et al., 2003). The inclusion process may therefore be used to tailor materials to have particular mechanical, electrical and optical properties (Das et al., 2009). However, to fully understand the nanocomposite, it is necessary to study the fundamental properties of both the host matrix and the inclusions (Li, 2008)."

Jan 1, 2012

By Leon C. Botham

?? Review of Requirements ?? Components of Modeling ?? Water Management ?? Tailings Management ?? Primarily a water management problem ?? Solids relatively easily contained ?? Process flows and runoff a continuous stream over life of mine ?? Need to allow this to safely happen over wide range of conditions

May 1, 2008

By Robert B. Parsons

"This article addresses the relationship between mine evaluation, the tax system, and economic risk. It is based on a paper presented by the author at recent seminars in Moscow and Tashkent on the subject of mine evaluation.IntroductionTaxation can have a strong influence on the feasibility of a mining project. For the most part, because metal prices are determined on a global basis, the mining concern is not able to pass on to its customers any portion of taxes which the concern has to pay. Taxes are a direct charge against the project. The purpose of the article is to highlight the various ways whereby different taxes can affect the financial viability of a mining operation.The first part of the paper identifies different forms of taxation, and the second part of the paper addresses the different forms of taxation in terms of risk analysis and impacts on the mining project. Finally, the third part of the paper makes brief mention of using the taxation system to provide incentives with respect to investment in mining activities."

Jan 1, 1993

By K. M. Deen, E. Asselin

Hydrometallurgical processes, i.e., Cu extraction from a mineral concentrate and Zn electrowinning, are coupled in a battery-like system. A naturally-sourced CuFeS2 concentrate mixed with activated carbon is used as a positive slurry electrode separated by a membrane from the negative compartment. The Zn is deposited on the negative Al current collector from the circulating solution containing 100 g L–1 Zn2+ in 0.2 M H2SO4. In this battery-like system, both CuFeS2 oxidation and Zn deposition are possible during the charging cycle. The additional benefit of this setup is the energy storage if discharged by re-dissolving the Zn in the negative compartment. Cyclic charge/discharge testing revealed oxidation of the mineral concentrate supported by the Zn2+/Zn redox reaction. The coulombic and energy efficiencies increased monotonically to 95.6% and 43%, respectively, with approximately 7% Cu extraction during the first 10 charge/discharge cycles (completed in 2.4 hours). The discharge energy density also increased from 2.7 to 36.2 mWh L–1. In the following 90 cycles, the low energy (~14%) and coulombic (~33%) efficiencies that were obtained confirmed the progress of irreversible reactions e.g. Cu extraction from the mineral concentrate. Overall, approximately 16% Cu was extracted from the mineral concentrate over 100 charge/discharge cycles (or about 12.2 hours). INTRODUCTION Chalcopyrite (CuFeS2) is the main economic copper-bearing mineral, which is generally processed through pyro-metallurgical methods to produce Cu. However, environmental challenges with smelting, depletion of high-grade ores and a large number of impurities (some toxic) have resulted in continued research aimed at the development of hydrometallurgical technologies to process CuFeS2. There are a number of different proposed hydrometallurgical routes in the literature to treat CuFeS2 concentrates, but only a few have attained commercial acceptance (Dreisinger, 2006). Zn is another commercially important metal that is mainly produced via acid leaching of roasted sphalerite (ZnS). The pregnant leach solution is rigorously purified to remove all the soluble metal impurities, particularly those that are electrochemically more noble than Zn and present large kinetic activity towards H2 evolution (Hu & Piron, 1992; Mackinnon, Brannen, & Fenn, 1987; Mureşan, Maurin, Oniciu, & Gaga, 1996). Metal impurities such as Cu, Co, Ni, Cd, Pb, Sb, As, Ge and Fe etc., if they exist in the leach liquor beyond the tolerance limits, can decrease the current efficiency during electrowinning and deteriorate the deposit quality (Alfantazi & Dreisinger, 2001). A complete flow sheet, describing the process steps of Zn metal production from mine site to pure metal is presented elsewhere (Brown, Meisenhelder, & Yao, 1983).

Jan 1, 2019

By Claude Gosselin

En 1995, la Compagnie minière Québec Cartier a mis de l'avant un projet de recherche sur la modélisation de l'écoulement des gaz pour ses fours de frittage à l'usine de bouletage de Port-Cartier. Cette démarche s'inscrivait dans un large processus de collaboration avec l'Université Laval et le Consortium de Recherche Minérale (COREM). L'usine de bouletage possède deux fours de frittage d'une capacité moyenne de 600 tonnes/heure pour chacun des fours. Les fours de frittage sont des systèmes complexes d'échange de chaleur qui fonctionnent à contre-courant (le débit de boulettes versus les débits de gaz). Pour rencontrer les spécifications reliées aux propriétés mécaniques des boulettes, le processus de fabrication requiert des mesures et un contrôle des systèmes très précis. L'information fournie par plus de 70 capteurs (pression, température, puissance, vitesse, hauteur de lit, position de volet....) est utilisée pour manipuler une vitesse de grille, cinq ventilateurs et neuf zones de brûleurs. Malheureusement, les variables qui influencent fortement les mécanismes de frittage, c'est-à-dire les débits de gaz dans les différentes zones du four ainsi que la masse de boulettes qui circulent ne sont pas mesurées. Une méthode est donc proposée pour une estimation en ligne de ces variables. La méthode est basée sur un arrangement de 65 équations reliant pressions, températures et débits de gaz dans les conduites, les ventilateurs, les sections du lit et les fuites (Gosselin, 1998). Pour des raisons de simplification de cet article, seul un sous-système du four sera présenté. Les techniques de réconciliation des données reliées à la conservation de la matière et de l'énergie montrent que la mesure en ligne du débit de boulettes mène à l'estimation des débits de gaz et apporte des avantages intéressants pour le contrôle des variables stratégiques des fours.

May 1, 2001