Search Documents

By S. K. Schwartz

"This paper describes the general layout of the environmental monitoring scheme at Devco 's No. 26 Colliery, including wall face ventilation, fan performance and methane drainage, and then goes on to discuss the sensors, the outstation layout, the surf ace control room and the protection of the system.IntroductionCape Breton coal mines have been pioneers in the use of the latest technology in mining coal on this continent. To mention just one example, continuous methane monitoring at the coal face was started in 1976 and the idea of automatically stopping the face conveyor during high gas levels using the face signalling system was conceived and developed by CBDC engineers.With the introduction of remote environmental monitoring, No. 26 Colliery will be the first underground coal mine in Canada and possibly in North America to have computer-based comprehensive environmental monitoring.Traditionally, surveillance of the mine environment has been based mainly on periodic checks by portable or hand-held monitors. Although this method proved adequate, it has some limitations, namely:1) restricted 'number of observations and samples;2) relatively long time between taking measurements and availability of results for assessment.With remote monitoring, the above limitations are overcome because (a) monitoring is continuous and (b) monitored data are updated quickly (typically 5-7 sec.). Remote monitoring also provides a centralized 'information center' at the surface from where the entire mine environment can be monitored. Details of modes in which data can be displayed and features available at the location will be discussed later in the paper."

Jan 1, 1982

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By Donald L. Brothers

"OUT IN BRITISH COLUMBIA, we have a legendary creature called ""The Sasquatch,"" a large ape-like creature which, according to those who claim to have seen it, somewhat resembles the Abominable Snowman of the Himalayas. Through the years, the legend bas been perpetuated by hunters and prospectors who return from remote wilderness areas with fantastic tales about hairy creatures, twice the height of an average human being, who leave 2-ft-long footprints in the soft forest floor. However, the existence of this creature bas never been proven and the attitude in British Columbia circles is that the whole thing constitutes either a great discovery or a giant hoax, and is about equally unbelievable either way.The Sasquatch, however, is not the only giant in British Columbia. If you find the Sasquatch story un-believable, you'll fi nd it just as hard to believe what is happening in the mining industry out west. We have opened four new mines so far this year (1967), another mine is expected to be brought into production before the end of the year and any mining man will tell you it's just the start of a mining boom which will continue for many years if metal prices are maintained and the federal government sees fit to discard the taxation changes pro-posed in the Carter Royal Commission Report regarding mining."

Jan 1, 1968

Presentation Outline ERM ? corporate profile Background to sustainability reporting GRI G3 Guidelines (Oct 2006) Best practice examples Contact information ERM ? corporate profile Over 35 years of experience World?s largest all-environmental consultancy* 130+ offices in 40+ countries; 3,200+ professional staff Worked with >50% of the Global Fortune 500 (FY07) Annual turnover > US$500 M (FY07) 2008 Environmental Advisor of Year** Offices/Staff ? Canada (5/50) and US (65/1,350) *Source: Engineering News Record: July 2, 2007 ** Source: Acquisitions Monthly: December 2007

May 1, 2008

By R. Amata

"The Gakara Rare Earth deposit in Burundi (East Africa) is unique for its high grade (e.g., 54.3% TREO on average) and low uranium and thorium levels. The majority of the light rare earth (RE) elements in material from Gakara are contained within the familiar RE minerals bastnaesite and monazite. Extensive metallurgical test work was conducted by SGS Minerals Services on mineral samples collected from the Gakara deposit. Various whole ore hydrometallurgical processing routes were examined in a scoping level test program. Preliminary beneficiation testing was also conducted, though it was determined that only marginal upgrading would be achieved with significant RE losses. Thus a hydrometallurgical process on whole ore was developed to minimize the overall process complexity and achieve maximum RE recovery. Results from the test work will be presented, along with the selected base case flowsheet involving agitated atmospheric sulphation of the RE minerals, RE double sulphate precipitation, caustic conversion, redissolution, and carbonate precipitation. Following the base case flowsheet, a purified cerium free mixed RE carbonate with low levels of radioactive elements was produced.INTRODUCTIONRainbow Rare Earths Limited (Rainbow) is a mining company engaged in the exploration and development of the Gakara rare earth deposit in Burundi; Figure 1 shows the project location. The project is located in the Bujumbura Province and 45 km from the Burundi capital of Bujumbura. Notable for its exceedingly high in-situ grade – 54.3% on average total rare earth oxide (TREO), low uranium and thorium levels and familiar rare earth minerals, bastnaesite and monazite – Gakara is the world’s richest rare earth deposit. The project, a previously operating mine from 1948–1978, has a significant mineral inventory base, a long life of mine, well understood mineralogy, and robust economics. Rainbow is focused on bringing Gakara into production in the near term, ramping up to produce 5,000 t/y of a 54%+ TREO concentrate."

Jan 1, 2016

By D. McConchie

BauxsolTM, prepared by treating bauxite refinery residues with Mg2+ and Ca2+, has an excellent ability to remove arsenic from acidic waters. The addition of BauxsolTM to sulphidic waste rock at the Gilt Edge Mine, South Dakota, reduced As concentrations in leachate water from 35 mg/L to < 0.005 mg/L; the concentrations have remained below 0.005 mg/L for the five years since the treatment was initiated. However, ordinary BauxsolTM does not effectively remove As from near-neutral water and it needs to be acid-treated or blended with small amounts of reagents, such as jarosite or ferrous sulphate, to increase the proportion of positively charged binding sites on the particles. The use of a jarosite/BauxsolTM blend can effectively treat ponded water, and As(V) concentrations can easily be reduced from over 1 mg/L to < 0.001 mg/L; As(III) has to be oxidised to As(V) for effective removal. Metal contaminants in the jarosite are trapped by the BauxsolTM and only very small amounts of the As, or other elements bound during treatment, are liberated using a TCLP leaching test. The exhausted treatment reagents meet the criteria for classification as an inert solid and do not need to be disposed of in a secure repository.

Jan 1, 2006

By S. Boisvert

Risk-based Inspection (RBI) addresses the challenges associated with ageing plants by focusing the inspection effort on the process equipments with the highest risk, thereby improving plant safety and reducing inspection costs. The RBI methodology is commonly used in the oil industry through the API 581 standard. Since no such standard exists in the mining and metals industry, BPR-Bechtel has developed one using inspection data from process equipments in CEZinc. Models were developed for various damage mechanisms, such as uniform corrosion and stress corrosion cracking. The equations were organized into a user friendly software that facilitates the implementation process.

Jan 1, 2010

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

By R. W. Davis

INTRODUCTION CHURCHILL river was named for John Churchill, first Duke of Marl-borough and third Governor of the Hudson&apos;s Bay Company, in the latter part of the 17th century, some fifty years after the ill-fated Danish expedition, led by Munck, had abandoned the site of the now famous seaport of Churchill, as a worthless, cold, disease-ridden country. No other attempts were made to explore the interior until the river basin became a part of the grant to the Hudson&apos;s Bay Company and began to play its part in furnishing the luxury of fine furs to civilized people as it had furnished the necessities of food and dress for untold centuries to uncivilized natives. This was the sole contribution of the region to the economic life of the country for some two hundred and fifty years, until 1926, when the power site at Island Falls was discovered by engineers seeking a cheap power source to make possible the development of the great ore-body at Flin Flon. DRAINAGE BASIN OF CHURCHILL RIVER The river is some 1,325 miles long. Rising in the headwaters of the Beaver river, in east-central Alberta, it flows in an easterly direction across Saskatchewan and northeasterly across Manitoba to Hudson bay, through a remarkable basin of some 115,500 square miles, only 6,000 square miles less than the area of the British Isles. A journey down this river leads one through three distinct belts of country, each vastly different from the others geologically and in surface characteristics. For the first five hundred miles the river flows through a basin of 36,000 square miles of the great central-plains country, which is covered with fertile soil and carpeted in its southern part with prairie grass, which gradually gives way to the mixed forests of poplar, spruce, birch, and jackpine in the northern and eastern sections: About midway across Saskatchewan, bald-headed knolls and ridges begin to make their appearance as the river meets the western margin of the Canadian Shield. Then, for some seven hundred miles, it passes through country underlain by the pre-Cambrian rocks of the Shield, which continue to within one hundred miles of Hudson bay. Here the character of the country again changes to a low, clay plain underlain by sandstone, and through this &apos;clay belt&apos; the river flows between steep clay banks, to empty into Hudson bay.

Jan 1, 1935

By G. A. Bezuidenhout, J. Davis, S. Lefume, J. P. T. Kapusta, D. K. Chibwe

"Although the centennial of the Peirce-Smith (PS) converting process has recently been celebrated, the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration. In the late 70’s and early 80’s, Brimacombe and co-workers demonstrated at both laboratory and plant scales that sonic injection (jetting regime) into copper or nickel converters could reduce or eliminate the above hindrances characteristic of PS converting. Since then, in spite of these successes, very little industrial applications have made headway in the converting process of non-ferrous metal mattes on a commercial scale. As part of its operational improvement and energy reduction program (process efficiency), Lonmin Platinum decided to conduct a full scale industrial evaluation of sonic injection using air only to establish if punchless, high efficiency sonic injection was feasible in its small 3.05 × 4.57 m converters (10’ × 15’). A plant trial was run for four weeks in one of its three converters. This paper discusses the plant demonstration with a focus on the experience acquired by Lonmin together with the key learnings from the trials. Reference will also be made to the commercial aspects of a full scale implementation of sonic injection in all three converters in the smelter. INTRODUCTION AND OBJECTIVESAlthough the centennial of the Peirce-Smith (PS) converting process has recently been celebrated (Peirce and Smith, 1909; Southwick, 2009), the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration."

Jan 1, 2012

By P. Cavanagh

Summary This paper discusses the fundamental principles which allow the development of a new method for studying the deformation and failure of metals in terms of &apos;internal microstrains&apos;. Internal microstrains mechanical and magnetic properties are defined and their influence on of metals is outlined. A research programme at present in progress will determine whether magnetic measurements of internal microstrains give sufficiently accurate values for predicting the performance of metals under service conditions. These magnetic test techniques are also being used to detect the beginning of plastic deformation and to trace the development of deformation processes and failure. Results of the experimental work in each field will be published. Introduction Any attempts are being made to develop a complete theory embracing the mechanical behaviour of metals. In spite of the amount of experimental data available, the theoretical approach is rather difficult, since most of the mechanical properties of a metal are determined by deviations from the pure chemical composition or the perfect crystal. Both types of deviation are difficult to reproduce experimentally and to describe theoretically. In general, there are three main avenues of approach to the problem being followed today.

Jan 1, 1950

By M. G. Lipsett

One challenge in applying information technologies in Mining is building a business case. In Mine Maintenance, there is a complex flow of information that contributes to making informed business decisions. By understanding those information relationships and the cost of wrong decisions, analysts can estimate the value of information flow. Developers can then ensure that systems deliver key information in an accurate and timely way. In this paper, general maintenance decision-making is discussed, with examples of how model-based analysis can improve the information delivered to decision makers.

May 1, 2001

By M. Matthias

A study, part of a doctoral dissertation (Matthias, 1991), was conducted during 1987 and 1988 to establish the means by which professionals assess and maintain their competence during the various stages of their careers. The study elicited responses from fifty-nine subjects representing engineering, pharmacy and medicine (twenty subjects from engineering, nineteen from pharmacy and twenty from medicine) on their perception and assessment of continuing competence. The findings revealed a wide variation of how professionals perceived their continuing competence and the means they adopted to keep current. The implications of the study are significant for adult education practice and theory building. The author strongly believes that now, more than ever, engineers must take ownership of their careers and professional development activities. While management and supervision have a key role to play, it is the engineer, who is ultimately responsible for the scope, planning and implementation of her/ his professional development needs. An example from one high technology company will illustrate these points.

Jan 1, 1999

By Radford B. Langston

Mining Methods Majority of Production Ramp and Fill at Stillwater, Sub-level Becoming More Important Production at East Boulder from Sub-level l Majority JM REEF ROCK TYPES NORITE - plagioclase and bronzite cumulate GABBRONORITE - plagioclase, augite, and bronzite cumulate TROCTOLITE - plagioclase and olivine cumulate ANORTHOSITE - plagioclase cumulate PERIDOTITE - olivine cumulate

May 1, 2002

By George Kellock

Introductory The Alberta Provincial Government has contemplated a revision of the Mines Act for some time past, and it is understood that a definite decision has now been made to do this at the next session of the Legislature. The Operators&apos; and Miners&apos; organizations of the Province have been asked, or at least have been given the opportunity, to submit their views and ideas relative to the proposed changes. The operators have already drafted out a number of changes which they feel would improve the Act from the standpoint of safety and practicability, and this paper has been prepared so that the general membership of the Rocky Mountain Branch of the Institute, which is composed largely of the operating and certificated officials of the mines, might have an opportunity to discuss, criticize, and improve upon the suggested changes which the operators are putting forward.

Jan 1, 1929

By G. M. Mason

History Due to its strong affinity for oxygen, aluminium as an element was isolated only after many other rarer metals had been prepared and studied. It was just over one hundred years ago that two scientists, Hans Christian Oersted and Friedrich Wohler, produced the first few pellets of aluminium and determined its physical properties. These early investigators used metallic potassium as a reducing agent. Later, St. Claire Deville, by using sodium instead of potassium, improved the yield in the reduction and produced some pounds of aluminium. From a figure of about $110 per pound in 1855, the price had fallen to about $4 per pound by 1886. In that year, a very important discovery was made independently by Charles Martin Hall in Oberlin , Ohio, and Paul . Heroult in France. Stated in its simplest terms, the discovery of Hall and Heroult was that aluminium could be produced by electrolyzing a solution of the oxide in molten cryolite. The application of the Hall-Heroult process made the metal immediately available in commercial quantities and, by 1900, the price had fallen to 23 cents per pound. The growth of the industry in the past fifty years is well known, and is outside the scope of this paper. It is, perhaps, not generally known that aluminium was first produced in Canada at Shawinigan Falls in 1901. Since that time, production has been continuous at one or more smelters in the Province of Quebec. The largest of these smelters, which is also the largest aluminium smelter in the world, is at Arvida, Quebec, on the Saguenay river. A large power potential and access to ocean shipping were the two principal reasons for the establishment of aluminium production facilities in the Saguenay district. It is interesting to note that the aluminium industry, as a large user of power, took an active part in the early industrial development at Niagara Falls and Shawinigan Falls, and is now repeating the process in the Saguenay valley.

Jan 1, 1949

By V. G. Papangelakis, M. Cheung, M. Dry

The high pressure acid leaching of laterite was modelled and simulated using a combination of two commercially available software packages, namely Aspen Plus 11.1 and the OLI Stream Analyzer. New kinetic parameters for the acid-controlled metal dissolution and precipitation reactions at temperature were first determined from previous experimental data on the leaching of limonite. A grain model with cylindrical pellets was used to model the solid-liquid dissolution reactions. Precipitation reactions were modeled via aqueous equilibrium chemistry. A dedicated thermodynamic database previously developed at the University of Toronto was used in conjunction with the OLI software to model the solution chemistry and calculate the concentration of hydrogen ions in solution at the leaching temperature. Mass balances were handled by Aspen Plus. The simulation gave good predictions of nickel dissolution under industrial and laboratory conditions, for the dissolution of limonite and limonite/saprolite blends. Computational

Jan 1, 2005

By M. Kosugi, Y. Kon, M. Kawata, J. V. Satur, K. Mitsuhashi, C. Tokoro, K. Horiuchi, R. Kawarabuki, B. Calabia

"Liberation of copper minerals is important in ensuring high flotation efficiency in copper sulfide flotation. The high pressure grinding roll (HPGR), microwave (MW), and electric disintegration (ED) are known to feature enhanced liberation over conventional comminution machines such as jaw crushers and ball mills by producing internal stresses on minerals or mineral grain boundaries through high compressive forces, thermal expansion of minerals, and pulsed high voltage discharges, respectively. In this study, each of these methods was applied before ball mill grinding to investigate its effect on enhancing the liberation of copper minerals in a low grade and fine-grained copper ore. The copper minerals observed in the tested ore sample are bornite, chalcocite, and chalcopyrite, and their grain sizes range from 10 to over 100 µm. Calcite, quartz, and feldsparare confirmed as gangue minerals. The liberation of the copper minerals by the different methods was analyzed using the mineral liberation analyzer (MLA) and compared. The result showed that the HPGR crushing was the most effective for enhancing copper mineral liberation. HPGR bench-scale test was then conducted on the copper ore and flotation was applied on a HPGR-treated sample to confirm the improvement in the flotation performance by applying HPGR.INTRODUCTIONIn order to recover copper minerals by flotation, copper ore is usually ground by ball milling to liberate the copper minerals from gangue minerals. In the case that the fine size copper minerals are targeted, grinding of the copper ore to a finer size is necessary to increase the copper recovery. However, finer size grinding by ball mill increases energy consumption significantly, which might deteriorate the economies of the mineral processing operation. HPGR, MW, and ED have been recently the focus of researchers as new techniques for enhancing the mineral liberation in mineral processing (Tavares, 2004; Kingman, 1998; Wang, 2010).HPGR crushing is considered to generate micro cracks along mineral boundary when rocks pass between two rolls by applying high compressive force. In the MW treatment, micro cracks are reported to be generated at crystal boundaries by differential thermal expansion of crystals attached to each other. In the ED treatment, micro cracks are known to be produced by plasma current flowing along mineral grain boundaries. These treatments are expected to increase mineral liberation (Fujita, 2001),improve flotation performance(Michaelis, 2005), and reduce ball mill work index(Kaya, 2010)."

Jan 1, 2017

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014

By K. Hardy

As part of Inco&apos;s $115 million Fluid Bed Roaster SO2 Abatement Project, a new weak acid treatment plant (WATP) was constructed to treat bleed solutions from the Copper Cliff Smelting Complex gas-cleaning circuits. The WATP produces an iron-arsenic co-precipitate, termed "basic ferric arsenate" (BFA), which requires disposal in an environmentally acceptable manner. Following analysis of many potential options, the short-listed disposal alternatives were: A) Co-disposal of the BFA?gypsum sludge with rock tailings, a portion of which would be used in mine backfill, with the remainder being sent to the tailings area, and B) Co-disposal of BFA?gypsum sludge with pyrrhotite tailings in the tailings area. Testwork showed that the addition of BFA?gypsum sludge to mine backfill samples increased the uniaxial compressive strength (UCS) of the backfill for most samples, especially those at lower binder content ratios. Extensive analysis was conducted on samples taken from the Copper Cliff tailings area, where BFA?gypsum sludge from Inco&apos;s Copper Refining Electrowinning Department has been co-deposited with pyrrhotite tailings since 1990. Pore water samples from these areas contained very low arsenic concentrations, indicating that the arsenic had remained stable in that environment. Ultimately, co-deposition with pyrrhotite tailings was chosen as the preferred option for the disposal of BFA?gypsum sludge from Inco&apos;s new WATP.

Jan 1, 2006