Search Documents

By M. Kalin

"Ecological Engineering, a biotechnological approach to the decommissioning of base metal mining wastes, is being tested on two pits (Gloryholes) in Newfoundland, Canada. Pit #2 has an average pH of 3.5 and flows into Pit #1 where, through additional ground water contribution, the pH is circumneutral, ranging between 5.5 to 7.The AMD in Pit #2 originates from underground workings and exposed massive sulphide on the pit walls. The overflow from Pit #1 averages about 10 L/s with less than 0.2 mg/L of Cu and 40 mg/L of Zn.Ecological Engineering utilizes organic substrate as a source of carbon and nutrients for microbial populations which can generate alkalinity and reduce metals. In 1989, limnocorrals (enclosures of 4 m diameter and approx 3 m depth) were placed in both pits to test the most suitable organic amendment (peat and sawdust). Microbial alkalinitygeneration was evident 95 days after placement of the amendment on July 4, 1989. The pH had increased after 120 days from 3.5 to 4.5 and by day 480 the pH was 7 in limnocorrals in Pit #2. Zinc concentrations in the limnocorrals in Pit #2, dropped from an average of 35 mg/L to about 2 mg/L or less, by day 480.A scaled-up experiment has been under way since August 25, 1990, where 390 m3 are treated in pit #2 and 750 m3 in Pit #1. One hundred eighty days after placement of the amendment, zinc was reduced in the acid Pit #2 from 40 mg/L to 15 mg/L. Research is underway to determine those factors which limit microbial activity."

Jan 1, 1992

By Staff

The Tetreault mine, operated by the British Metal Corporation (Canada), Limited, holds a unique position in Canadian mining, being the only steady producer of zinc in Canada east of the Rocky mountains. Its importance in Canadian zinc production may be gauged with some accuracy, since, in 1927, it was responsible for over 13 per cent of the zinc output of the Dominion. In addition, it also made valuable contributions to the production of lead, silver, and gold. Location: Situated in the foothills of the Laurentian mountains, 600 feet above sea level, 20 miles from the St. Lawrence river, and 52 miles due west from the city of Quebec, the property is in the township of Montauban, county Portneuf, Province of Quebec, as shown in Figure I. The municipality of Montauban, immediately adjoining the mine, has a permanent population of 700 people and is six miles by road from Notre Dame station on the main line of the C.N. Rys. between Montreal and Chicoutimi-Notre Dame being n6 miles by rail from Montreal. Connection by 19 miles of dirt-and-gravel road with the Provincial highways' system of Quebec Province, the city of Quebec, which is distant 78 miles, can be reached by automobile in less than three hours, while the distance to Montreal by road is 16o miles .

Jan 1, 1928

By Donald Leroux, Lori Lynn Smith, Robert Hutchison

"The grinding circuit of the Heath Steele concentrator was sampled under five different sets of operating conditions. The balanced results of the sampling campaigns were used to calibrate steady-state rod mill, ball mill and cyclone models using a commercial simulation software package (JKSimMet® ). Thirteen process variables had the potential to affect significantly the performance of the grinding circuit. Statistical-Design-of- Experiments techniques were applied to plan the suite of simulations in order to improve the quality of and minimize the time to find the optimal solution. The effect of each factor on three performance indices (the cyclone overflow size distribution, the circulating load and the cyclone underflow density) was modeled with empirical polynomial relationships using another software package (Design-Expert@)T. he conditions under which the cyclone overflow size distribution was maximized while respecting circulating load and cyclone density constraints were identified using these relationships. Among the most interesting results is the prediction of a set of conditions where the circuit target size distribution is achieved with only three ball mills instead of four.IntroductionProduction at the Heath Steele concentrator (near Miramichi, New Brunswick) started some 43 years ago at a rate of 750 t/d. The plant capacity was increased to 4000 t/d through successive expansion phases in the seventies (Sapiro, 1977; Johnston, 1978). However, as a result of depleting ore reserves, the plant throughput had to be gradually reduced to the current production rate of 2700 t/d. Heath Steele Mines currently have proven and probable reserves which would see it producing until the end of 1999 (Noranda Inc., 1997).An analysis of the grinding circuit of the Heath Steele concentrator was recently commissioned to identify opportunities for reducing operating costs while maintaining budgeted mill throughput and metallurgical performance. Since the plant will likely be operated below nominal capacity for the rest of its lifetime, the possibility of improving grinding efficiency by operating with fewer ball mills and/or crushers was contemplated."

Jan 1, 1999

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine. The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semi- variogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates.

Feb 1, 2004

By R. H. Batey

"The process control and cost of monitoring mining slurries is normally accomplished using a continuous mass flow system, conventionally embodying a volumetric magnetic flow meter and nuclear density meter. DuPont’s Maxville Mine at Starke, Florida, USA was chosen to examine costs associated with performance of a nuclear density meter. Since it is typical of many mid-sized establishments and has a long history in their use. The published accuracy under ideal conditions of a nuclear density meter is ± 1.0%, but in practice considerable ambiguity of cost in annual production implies ± 2% at best. Using such accuracy in a 400mm (16”) pipe carrying zircon slurry at 75,000 tons/day, the cost of ambiguity, together with initial and running costs, amount to nominally $962,000 per year.Such cost leaves much to be desired. This paper describes an unique continuous, direct mass per unit volume Density Meter used for mining slurries in pipe sizes up to 1000mm (40”), which significantly reduces the cost of ambiguity of measurement and running costs. At the same time the disadvantages of nuclear devices are obviated.In an effort to reduce costs, a 400mm non-nuclear Density Meter was installed at the DuPont Maxville mine. A typical on-site accuracy can be shown to be ± 0.285%, whereby the cost of ambiguity, initial and running costs in the example above shows an annual improvement of $78,660, a reduction of over $880,000 per year.Even higher cost savings may be demonstrated with mass flow systems having gas entrainment compensation. Unlike nuclear and other inferential density meters, the signal quality of this non-nuclear Density Meter is totally unaffected by entrained gas found in mining slurries. This non-nuclear density meter is then ideally used with a vortex velocity domain sonic flow meter, and provides for the first time compensation in wet density or dry % solids, as well as wet or dry mass flow of mining slurries with entrained gas, resulting in enormous reductions in cost ambiguity."

Jan 1, 2013

By D. C. Sharpstone

THE Polaris-Taku mine is a new gold property, situated in the far north-west corner of British Columbia. Production was started in November, 1937, at the rate of 150 tons a day, and recently has been increased to 200 tons. The property, which promises to become one of British Columbia's important gold mines, was developed and brought into production in twenty-nine months after work was started on it as a virtual prospect in June, 1935, by Edward C. Congdon and associates. Inaccessibility, extraordinarily complicated geological problems, and difficult metallurgy retarded development of the property before acquisition by the present interests, an::l, in fact, discouraged two companies that had spent substantial sums upon it from continuing development. This paper is concerned with reviewing the development of the property and describing the principal features of the geology, the mining and metallurgical practices, and the equipment employed. Acknowledgments The writer is indebted to Mr. Edward C. Congdon, President of the Polaris-Taku Mining Company, and to various members of the mine staff for their assistance in assembling the data for this paper. Special thanks are due to Mr. George G. Griswold, Jr., of Butte, Montana, who generously and painstakingly prepared the section dealing with milling and power. Microscopic studies of ores were made by Professors Frank Grout an::l G. M. Schwartz, of the University of Minnesota, and by Mr. Griswold.

Jan 1, 1938

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By Arnaud Faucher, Claude Bazin, Marilène Renaud, Mohamed Mai Manga

"Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action needed to minimize its impact on the process. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality. Recovery losses in downstream leaching or flotation circuits justify the effort in developing techniques for the detection of hydrocyclone malfunction. Two approaches for the detection of hydrocyclone fault are presented in this paper. The first proposed method uses the conventional sensors available in a grinding circuit allowing real time detection of hydrocyclone abnormal operation. The second technique is based on the use of vibration sensors installed on the hydrocyclone of a nest. This last technique enables the classification of the hydrocyclone malfunction as surging, overloading and plugged apex. The two techniques can be combined to increase the robustness of the problem detection.INTRODUCTIONHydrocyclones are used for many purposes ranging from water separation, fines removal and obviously for the preparation of the feed for subsequent concentration circuits in a mineral processing plant. The strategic role of the hydrocyclones for the preparation of the feed to the concentration circuit is often underestimated because of their simplicity of operation and robustness (Napier-Munn et al., 1996; McIvor, 1988). It remains that despite their simplicity, hydrocyclones have been studied extensively from 1970 to 1990 with the objective of developing mathematical models of their operation to be incorporated into grinding circuit simulators (Napier-Munn et al., 1996; Lynch, 1977; Flintoff et al., 1987). Such a development effort is already an acknowledgement of the importance of these units in a mineral processing plant. Several authors (Del Villar et al., 1996; Plitt and Kawatra, 1979; Casali et al., 1998) proposed soft sensors to estimate the classification efficiency of hydrocyclones using sensor measurements. However, few of the proposed sensors are used in the industry. More recently several papers were published to discuss the application of 3-D modelling of the hydrocyclones (Narasimha et al., 2005; Cullivan et al., 2004) and sensors (Bond et al., 1999; Neesse et al., 2003; Hou et al., 1998; Olson and Waterman, 2004; Williams et al., 1995; Willams et al., 1997) to help in the detection of hydrocyclone malfunction."

Jan 1, 2010

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, Canada, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic meters/day wastewater containing 30-60 mg/l zinc, demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic control equipment, the system has evolved to a full-scale operation capable of treating 800 cubic meters/ day wastewater containing 4-11 gm/l zinc. Treated effluent contains 0.2-20 mgll zinc. Hydroxide sludge produced returns to the metallurgical process for recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing ii return from metal recovery."

Jan 1, 1980

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

By D. M. Doyle

"A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc. over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study 11rogresses through monthly, daily and finally, into quarter hourly data, the variations become more evident and most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program.The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Sudbury Operations, the material and control equipment, the commitment, the new energy accounting practices and lastly, the policies. Examples of successful energy conservation endeavors include automatic peal electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailmen: of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and if necessary, immediate reporting of energy and energy per unit of production information. The program so reported at Falconbridge’s Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0 million dollar annual energy account."

Jan 1, 1979

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By C. R. Stelck

"AbstractThe Cardium formation of northeastern British •Columbia •contains an erosional unconformity that becomes progressively more severe northward until, •at Liard river, the stratigraphic hiatus eliminates the underlying Lower •Cardium sandstone, the Kaskapau formation, and the upper Dunvegan sandstones. The area of unconformity roughly coincides with the distribution of the continental facies of the earlier Dunvegan formation. Along Wapiti river, the zone fossil Scaphites ventricosus Meek and Hayden is found in the Bad-heart member of the overlying Wapiabi shale; Scaphites :preventricosus. Cobban marks the base of the Wapiabi shale; Scaphites cf. corvensis •Cobban is found in the middle shale member of the •Cardium formation. The log of the Red-Willow No. 1 well shows close similarity to the outcrop sections south of Wapiti river. The Cardium formation is mainly late Turonian in age. Two other pre-Cardium Turonian sands of north-eastern British Columbia are named the Wartenbe and Tuskoola sands.IntroductionTHE Upper Cretaceous Cardium (Bighorn) sandstone formation of the Foothills of northeastern British Columbia carries within its formational limits an erosional unconformity. The unconformity decreases to the southeast, becoming in immediate shoreline regions, now under the plains, a minor diastem. Such diastems, or stratigraphic intervals of non-deposition, occurring in the shallow unda-zone are paralleled in the deeper portions of the unda-zone by the phenomena of sub-aqueous winnowing. '.This winnowing and re-working •at critical depths creates sand areas with porosity."

Jan 1, 1955

?General Facts:Barrick?sFirst Mine in Peru Production started in November 1998 ?The Facilities:Open Pit, Primary and Secondary Crusher Valley Fill Heap Leach PadMerrill Crowe PlantRefinery Environmental Facts: High Rainfall - Average Annual Precipitation of 1,200 mm (47 inches) Rainfall Events: Common 20mm daily events High Altitude Site - Elevations range from 3900 to 4250m. Steep topography - Terrain ranges from 3:1 slopes up to cliffs. Water Issues: Sediment Control - Open Pit PAG Encapsulation - Waste Dump Stormwater control - Leach Pad Erosion Control Techniques ? Offsite impacts mitigation Social Issues: 11 communities surrounding the property Town of Huaraz

May 1, 2003

By Orlando C. Gaspar

Abstract - The presence of fine-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sulfide ores. The beneficiation of most massive sulfide ores from the Iberian Pyrite Belt requires extremely fine grinding to liberation sizes of K80 = 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning patterns has shown that the different ore types are distributed as ore lenses within the massive sulfides. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the efficiency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types defined at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sulfide ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By Orlando C. Gaspar

The presence of ?ne-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sul?de ores. The bene?ciation of most massive sul?de ores from the Iberian Pyrite Belt requires extremely ?ne grinding to liberation sizes of K80= 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning pat-terns has shown that the different ore types are distributed as ore lenses within the massive sul?des. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the ef?ciency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types de?ned at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sul?de ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997