Search Documents

By J. H. Ffolliott

ALL, of the prospects that later became mines in the Ducktown district were discovered prior to 1854, and most of them were exploited before the turn of the century. It is the purpose of this paper to discuss the exploration and current development of the Boyd mine, discovered in 1853. It is in the heart of the Ducktown Basin, in the extreme southeast corner of Tennessee, and is being developed by the Tennessee Copper Co. GEOLOGY The geology of the district has been fully described in many papers. Probably the most complete description is that of Emmons and Laney.1 The rocks of the district are considered to be of Lower Cambrian age and are a part of the Great Smoky formation, consisting mainly of interbedded graywacke and mica schist, in which the ore deposits occur. The ore bodies are included in an area of about 6 sq. miles, 2 miles wide and 3 miles long striking N. 45° E., and may be grouped into three general lode systems. The northeast system, including the East Tennessee, London and Burra Burra ore bodies, and the southeast group, comprising the Polk County, Mary and Calloway deposits, are all characterized by relatively high copper values. The ores of the central system, which includes the Eureka, Boyd, Old Tennessee and Cherokee ore bodies, are low in copper and high in total sulphide content. Boyd mine lies roughly halfway between the Old Tennessee and Eureka ore bodies [ ] and 2500 ft. in the hanging wall of the Burra Burra mine (Fig. 1). Elevation of the surface is about 1725 ft. above sea

Jan 1, 1942

By M. T. Simnad, G. Derge, Ling Yang

A method is described for using radioactive tracer for the direct determination of ionic mobility in a molten electrolyte. The ionic mobility of Fe" in silica-saturated iron silicate is found to be 0.0009 (*0.0002) cm2 sec ' volt L at 1250°C. eLECTROCHEMICAL studies', ' of molten iron eE oxide and iron silicates have shown some ionic conductivity at all compositions. The current efficiency in electrolysis increases with the concentration of silica to a maximum of 90 pct at about 34 pet SiO,. In the silica-saturated melts the transport number of ferrous ions is near unity, indicating that

Jan 1, 1957

By Bruce A. Kennedy, Richard M. Stewart

Slope stability has now become a practical tool in the design and operation of open pits. The selection of slope angles is a critical decision that can have far-reaching effects on the accumulated cash flow and the overall profitability of a mining project. Slope failures can now be dealt with in a number of ways. Two methods - the total removal and the partial unloading of a failing zone-have been practiced for many years. However, with the refinement of monitoring techniques, open pits can now learn to live with a slide and even turn a potential loss into a gain. There are various techniques, such as presplit blasting, drainage systems, and artificial stabilization, which can be applied immediately in an existing open pit to improve the stability of the pit slopes. The technology of slope stability will play an important part in the future mining of low grade, previously marginal orebodies, which will have to be exploited if the mineral needs of the world are to be met.

Jan 1, 1971

Six hundred miles inland from Australia's east coast Port of Townsville in Queensland's sea of rock and spinifex lies Mount Isa. The town, as in most mining towns, is dominated by its mine and the mine in turn is dominated by its 503 ft copper smelter stack. This candy and white painted stack is a striking introduction to one of the world's greatest copper producing mines and a town where people of over 40 different nationalities live remote but well. Mount Isa Mines Limited is surging into the ranks of' the world's great mines on the momentum of a relentless push begun in 1956. It is as if the time lost in the lean years of the past should be caught up in a hurry.

Jan 10, 1964

By J. S. Ross

Few Canadians realize the role of their domestic industrial minerals industry because it is over-shadowed in production value by a large metallic minerals industry. But since 1960, Canada has had a reasonably well balanced, mature industrial minerals industry; and although the nation's sparsely scattered population has not been able to support an industrial minerals industry in a manner comparable to the domestic and foreign support given the metal mining sector, Canada is, nevertheless, exporting large quantities of higher priced nonmetallic minerals. Production of many of the basic minerals had been firmly established long before 1960, but it was not until the late 1950's that the output of cement, salt, titanium dioxide pigment and slag, sulfur, gypsum and sodium sulfate reached relatively high levels. Shortly after 1960, the significant potash and lithium chemicals industries were established and their effect is just now being realized.

Jan 11, 1964

By F. C. Blickensderfer

DURING 1914 and 1915 extensive experiments were conducted at the concentrator of The Detroit Copper Mining Co. of Arizona, at Morenci, Ariz., in order to test the relative grinding efficiencies of the Marathon, the Chilean and the Hardinge Mills. The Marathon mill used in the experiments was the first one ever built by the manufacturers; and since this was the first time that it was given a thorough tryout, with such remarkable results, the data have been, assembled in the following paper and submitted in the interests of the milling profession.

Jan 8, 1916

By J. F. Enrietto

It is shown that one cannot approximate the broad internal friction Peaks observed in the Fe-Mn-N system as the sum of a number of subsidiary Peaks and still vetain the concept of a single relaxation time. Furthermore, the approximation of manganese affectirg only nearest neighbor interstitial sites is shown to be incompatible with the experimental results. The results of this experiment show that the influence of manganese in the ferrite lattice extends over 3 to 4 atomic distances. NUMEROUS experiments have shown that the presence of relatively small amounts of substitutional alloying elements can profoundly affect the profile of the damping spectrum in the vicinity of the Snoek peak in bee metals.1-7 Dijkstra and Sladekl observed this phenomenon in Fe-Mn-N alloys where it appeared as a broadening and shifting of the Snoek peak to higher temperatures. The authors interpreted this as being the result of a superposition of two damping maxima—the normal Snoek peak, located at its usual position and having a normal half-width, and an interaction peak having a normal half-width, but occurring at a somewhat higher temperature. They prclposed that the interaction peak was caused by nitrogen atoms jumping from Fe-Mn sites to Fe-Fe sites, the Fe-Mn interstitial sites having one manganese and one iron atom as nearest neighbors, and the Fe-Fe sites having two iron atoms as nearest neighbors. They further suggested that the Fe-Mn sites had a lower energy than the normal Fe-Fe sites because of the presence of the adjacent manganese atoms. From the relative heights of the two postulated damping peaks, the dif-

Jan 1, 1962

COLUMBIA SECTION J. C. HAAS, Chairman W. J. HALL,. Vice-chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY J. F. MCCARTHY At a meeting of the members of Columbia Section, which was held in the Davenport hotel, Spokane, Wash., Jan. 31, 1919, at noon, there were present' about twenty members and guests. The chairman being absent, Mr. Frederick Keffer presided. The Secretary announced the personnel of the executive committee of the section, which is: J. C. Hass, Spokane, Chairman; W. J. Hall, Wallace, Ida., Vice-chairman; S. S. Fowler, Riondel, B. C., Past Chairman; L. K. Armstrong, Spokane, Secretary-Treasurer; R. M. Betts, Cornucopia, Oregon. It was stated that the geological survey and report on Stevens Co., Wash., has been completed and will be printed soon. The geologic survey of Colville Indian reservation, by J. T. Pardee, U. S. G. S., has been published as Bulletin No. 677 and is available for distribution, The Miner's Almanac, Miners Circular No. 24, U. S. Bureau of Mines. is also available upon request. There was considerable discussion on the program for meetings during the year. It was informally agreed that, if agreeable to Coeur d' Alene members, that one meeting should be held in that district, preferably at the time of the annual visit of Institute officials. It was also proposed to hold at least one open-air meeting in Spokane with suitable program. The activities of other sections were noted with favorable comment. In this connection there was much general discussion on the subject of closer relations between the national engineering societies. It was agreed that cooperation was desirable and imperative if the greatest measure of value be realized from the profession. It was not the sense of the members, however, that complete amalgamation is desirable. This expression of local sentiment is to be presented to the Institute

Jan 3, 1919

By Ronald F. Ayers

The basic research for this study was conducted by Battelle's Columbus Laboratories in 1974. The high-sulfur content of coal threatens to erode its competitive position in the future. The impact of sulfur removal on final costs of eastern interior coal lies at the very heart of this market analysis. An extensive market survey was conducted that considered both traditional coal markets as well as anticipated future markets. Competition for coal from this province considers low-sulfur Western coal, nu- clear power, international oil and coal trade, as well as Appalachian coal producers. Based on projections of future energy consumption under several scenarios, a comprehensive market forecast for eastern interior coal was made to 2040. The study upon which this paper is based was completed by Battelle's Columbus Laboratories for the U.S. Army Corps of Engineers in 1974. It is but part of an overall effort by the Corps to evaluate the costs and benefits to the nation of waterway improvements. This study is primarily concerned with future coal markets for production from those counties near the Wabash River in the heart of the Eastern Interior Province. An objective here is to consider a most pessimistic energy (and hence, coal) demand for planning purposes.

Jan 1, 1978

Dubbed "Freeport's Mission Impossible" by the trade press, the company's Ertsberg mine in West Irian nevertheless shipped its first concentrates in December 1972, ahead of schedule. This is a new and great chapter in the history of Freeport Minerals Co. and its contractors. Exploration and construction were only possible by moving equipment and supplies by helicopters. This work was carried out by Petroleum Helicopters, Inc., of Lafayette, La. At the peak of operations six machines were in service manned by 11 pilots and supported by 10 mechanics. During the month of August, with work in full swing 1,604 tons were moved, including 3 DC-6 tractors requiring 18 trips each; flying hours for the month were 636.

Jan 1, 1973

Meeting, Aug. 20, 1913, B te, Montana, at 12.45 p.m.-On, the written request of 27 members of oft Institute residing in Montana, the Montana Local Section was established, and the following Committee was appointed by the President of the Institute to complete the organization : E. P. Mathewson, Chair pan; Frank M. Smith, Vice-Chairman; D. C. Bard, Secre-tary, Montana State School of Mines, Butte, Mont., Oscar Rohn, James L. Bruce. The President reported the appointment of a Committee on Mining Law, the names of whose officers and members are given on page xxxv of this Bulletin, and these appointments were approved. It was voted: That the Committee on dining Law be requested to establish a Sub-Committee on Censorship, a majority of whom shall be lawyers; and, further, that no paper on mining law be recommended for publication to the Committee on Papers and Publications, unless it is previously approved by the Sub-Committee on Censorship of the Committee on Mining Law. The President reported progress in the matter of co-operation between the Institute and the United States Bureau of Mines, through Committees of the Institute. The President reviewed the history of plans for a union or affiliation with the Mining and Metallurgical Society of America, and the following minute was then adopted : " The Board of Directors of the American Institute of Mining Engineers has carefully considered for several months the question of union or affiliation with the Mining and Metallurgical Society of America ; and, while at an earlier time and under other circumstances, such. a union might have been accomplished, yet under present circumstances the Directors of the Institute deem such union inexpedient. "While thanking the Mining and Metallurgical Society of America for its consideration of the matter, we believe that further discussion of the subject will serve no useful end, and we conclude it best that the Society and the Institute continue their useful functions and friendly relations side by side, as heretofore."

Jan 10, 1913

At Black Lake, Quebec, Lake Asbestos of Quebec Ltd., a wholly-owned subsidiary of American Smelting and Refining Co., has opened a $36-million mining and milling operation which will produce about 100,000 tons of asbestos fiber a year and add 7 pct to the Free World's supply. The orebody once lay beneath Black Lake, and readying the ore deposit for open pit mining meant removing about 37 million cu yd of overburden- 30 million cu yd by dredging and pumping, and 7 million by power shovels and trucks. The enormous amount of material to be dredged, control of drainage during dredging, the need to cope with drainage problems in the area and to provide for flood control to replace the regulating effect of the lake, posed unusual engineering challenges and required tremendous capital investment.

Jan 1, 1959

By Hallan N. Marsh

The subject of this paper is apt to bring to mind wells ranging from 6000 to over 8000 ft. in depth. However, it is uncommon to pump wells at depths greater than about 5000 ft. Fig. 1 shows the number of wells being pumped at various depths by one company in Southern California. A few companies have a very few wells pumping at depths greater than this. This paper will deal with wells between 3000 and 5500 ft. in depth. Most California oils at these depths are between 25" and 35" gravity. The subject is so broad that it will be necessary to omit many interesting phases, and to treat others very briefly. Power, power transmission equipment, power efficiency, counterbalancing, sucker rods, pumps and volumetric efficiency will be discussed. Power As a source of power, the 50/20-hp. electric motor is generally preferred. Input is generally between 10 and 25 hp. Due to the uneven-ness of the load, an input of 20 hp. on the low range is generally about all that these motors will carry without overheating, in spite of their overload capacity. In some cases the capacity of the motor limits the speed

Jan 1, 1929

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furbish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 10, 1913

By Michael J. Fiannnaca, Michael M. Easdon

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Gold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 8 Mt (9 million st) of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 0.9 Mt (1.0 million stpy 1. Careful evaluation of the combined results of successive sampling projects has established the pit plan, minable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1985

By H. Tanner, T. Heikkinen

In1950 studies concerning mining and milling of the approximately 17 million tons of ore remaining at Outokumpu revealed the surface facilities for economical treatment were inadequate. The two shafts would soon be too far from the mine workings. Moreover, in spite of several extensions, mill capacity was insufficient and recoveries were not satisfactory. Therefore it was decided in 1951 to sink a new shaft and to build a new mill and auxiliary surface buildings around the shaft. The new shaft was sunk near the center of the remaining orebody, about 650 ft from the ore to the footwall side. This location placed the main part of the shaft as well as the crusher rooms and the ore bins around the lower end of the shaft in the firm and strong mica-schist.

Jul 1, 1955

By W. Rostoker, H. Nichols

The embrittlement by mercury of aluminum alloys in various states of anneal, cold work, and aging has been studied. It is shown that single phase and non-precipitation hardened structures irrespective of de,pee of prior cold work demonstrate some small measure of yielding before fracture occurs. Sub-yield-stress failure is confined to the aged state, and embrittlement is accentuated by small plastic prestrains. With large plastic pyestrains, embrittle~nent is progressively reduced. In previous work' it was shown that the propensity of commercial aluminum alloys for embrittlement when wetted with mercury seems to be related primarily to the intrinsic strength in the normal un-wetted condition. The data from a large number of commercial alloys in various states of anneal, cold work, and/or aging gave a generalized relationship. At low strength levels, the wetted fracture strength increases proportionately to the increase in tensile strength; but above 65,000 psi normal ultimate strength, the trend is abruptly reversed, and the wetted fracture stress decreases proportionately to the increase in tensile strength. This paper will demonstrate that the simple character of this relationship between normal tensile strength and wetted fracture strength is fortuitous. It will be shown that structure and thermal-mechanical history are clearly relevant factors. The term brittle fracture has been used to connote the geometry of the fracture surface (transverse vs shear plane) or the negligible extent of preceding plastic strain. At its maximum effectiveness, liquid metal embrittlement can satisfy both criteria—fracture transverse to the axis of tension and without observable plastic strain. In this paper, brittle fracture will signify failure at stresses below the engi-

Jan 1, 1962

[ ]

Jan 1, 1938

By John Birkinbine

The estimated product of iron-ore in 1888 throughout the world was, in round numbers, 50,000,000 gross tons, of which the United States produced about one-fourth. Great Britain leads this country in production by about 15 per cent., but the output of the United States is practically equal to that of Spain, France, Russia, Austria and Hungary combined. We produced last year nearly twice as much iron-ore as Spain, with all her exports; and we mined 20 per cent. more than Germany and Luxemburg. In addition to the domestic iron-ores consumed in this country, 587,470 gross tons of foreign ore was imported, and the amount of mill-cinder used in blast-furnaces is estimated at 450,000 gross tons. The total quantity of iron-ore required in 1888 for blast-furnaces, rolling-mills and other purposes in the United States was approximately 12,700,000 gross tons. The purpose of this paper is to indicate the principal sources of this supply, and call attention to the extent of mining operations covering many years in certain localities, which, although some of them now produce but a small proportion' of the above total, have in the aggregate added very largely to the material

Jan 1, 1889

By J. J. Bailey, R. C. Dean

Dr. Maurer has reviewed the large and confused field of rock mechanics and drilling. We have focused our attention on advance drilling and the disengagement of rock. To understand drilling in greater detail is certainly desirable, but such understanding does not necessarily hold any certain promise of near-term practical advancement. In the longer term, it is probably essential. Present work on drilling and our understanding of drilling falls roughly into three separate classes (and, indeed, these are in no way peculiar to drilling): 1) we have knowledge of certain (scientific) topics which seem to be relevant to the process, 2) we have knowledge of the drilling process in both qualitative and quantitative terms from observation of the actual process, and 3) we have certain modeling procedures, by which we bridge the gap between these two previous areas. The usefulness of our scientific knowledge depends critically upon this last item. In all our following remarks we shall consider only those problems of drilling and the disengagement of rock in which the rock behavior is essentially brittle. Let us start by examining some of the problems of constructing an even moderately detailed theoretical model of the drilling process in the small. The prospects of any near-term success in that direction seem extremely meagre; nor is it clear that any great advancement in the practical art of drilling is even likely to result from the construction of such a detailed model. On the other hand, as we shall suggest later, considera-

Jan 1, 1967