Search Documents

For many years it has been known that large bodies of iron ore existed in Iron and Washington counties in Utah. The ore is chiefly hematite-both hard and soft-though some magnetite is found. No definite and complete estimate of the iron ore reserves of the state have been made. The U. S. Geological Survey estimated that 40,000,000 tons of ore were disclosed by development work averaging only 35 feet below the surface of the ore. The ore is found along an area about one and a half miles wide by twenty miles long, and for the most part on the eastern and southern slopes or foothills of Three Peaks. Granite Mountain and Iron Mountain. Later estimates by others have gone as high as ore in sight 164,000,000 tons, probable ore 300,000,000 tons and possible ore 1,000,000,000 tons. Whether this last estimate is too great or not there is sufficient iron ore in Utah to justify the starting of an iron industry. Two companies are now mining iron ore in Utah, the Columbia Steel Corporation and the Utah Iron Corporation. The mine of the Columbia Steel Corporation is at Iron Springs a few miles west of Cedar City. About 650 tons, of ore a day is being shipped to the blast furnace at Ironton. The ore is mined by the glory hole method. After being drilled it is blasted to the bottom of the several glory holes and is dropped through chutes into cars on the ore haulage level below. It is then hauled by electric locomotives to the crushing plant, where it is crushed to blast furnace size before going to storage bins. Some of the softer ore is brought to the chutes by Fresno scrapers.

Jan 1, 1925

By J. Ruzicka

In creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently hear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addition to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabricated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment. The Equipment The creep equipment consists essentially of a tank containing a constant-temperature oil bath in which the creep of 14 specimens, loaded by means of levers, is measured by means of one movable extensometer. Figs. 1, 2 and 3 illustrate its general construction and appearance. Constant-temperalure Oil Balh.—A common constant-temperature bath requiring only one temperature-controlling equipment for a number of specimens was chosen as the best means of fulfilling the requirements of low cost and compactness. In addition, this allows the testing of a group of specimens under identical temperature conditions.

Jan 1, 1937

By G. H. Shefelbine

DISCOVERED during the time of the Spaniards, the Namiquipa silver-lead-zinc mines in Chihuahua, Mexico, remained idle until 1916, when mining claims were first denounced. About 1922 a Japanese company, the Santo Domingo Mining Co., was formed to mine the oxide silver ore. The company built a 75-tpd cyanide plant and mined in the area for a number of years. Because of an error in surveying in one of the company's mines situated in another district, mining was carried over into a claim owned by General Marcel Caraveo, at that time governor of Chihuahua. Santo Domingo Mining Co. lost the resulting lawsuit and consequently had no capital to continue operating at Namiquipa. Later, Ray Brown and Eugenio Caballero formed a company to operate the mine, shipping crude ore to the American Smelting and Refining Co. smelter at Avalos, Chihuahua. The cyanide plant was changed to flotation with a capacity of 75 tons per 24 hr. In 1936 the property was again closed owing to labor trouble, a drop in the price of silver, and increased water in the mine.

Jan 10, 1957

By E. Hoek

INTRODUCTION Rock slope stability research has been in progress for the past four years at the Royal School of Mines in London under the sponsorship of a consortium of 23 companies* with interests in open pit mining. This paper reviews the principal aims and achievements of this research project. In order to assist the reader in following these details, the basic philosophy underlying the formulation and direction of this research project is discussed. DISTRIBUTION OF RESPONSIBILITY In open pit mining, the economic necessity of keeping waste rock removal to a minimum generally means that the mine slopes have to be excavated to the steepest possible slope angle. On the other hand, excessive steepening of these slopes can induce failures, which may negate the economic benefits that have been aimed at and which may also result in loss of life and damage to equipment. Consequently, where slope failures are likely to prove to be a problem, an evaluation of the stability of the slopes to be created should be included as part of the overall pit design. How is the stability of a rock slope evaluated? When this question was examined, during discussions on the research policy to be followed at the Royal School of Mines, it was clear that relatively few satisfactory techniques were available in a form that would be comprehensible and therefore useful to the practical mining engineer. It was recognised that the research project must be directed towards two distinct aims: a) The evaluation of existing techniques for rock slope stability analysis and the provision of new techniques where these existing methods were found to be inadequate and b) The presentation of the results of this evaluation and research in a form that would be useful to engineers without specialist training in rock mechanics. It was soon realized that a university based research team, however large and efficient, could not achieve these aims without the co-operation and assistance of mining engineers,

Jan 1, 1972

By L. W. Strock

Metallurgists handling lead and zinc ores have long been familiar with the spectrograph as a routine analytical tool, as its earliest regular use by American industry was in controlling impurities of zinc metal and its alloys. This application has been extended to other metal industries on an extensive scale, accompanied by refinements of procedure to such an extent that a large part of some metals produced, especially magnesium, aluminum and steel, are checked only by spectrographic methods for conformity to specifications. The spectrographic analysis of ores and other poorly conducting powdered solids presents difficulties not encountered with metallic samples, which can be arced or sparked as self-electrodes or can be readily dissolved, so that their solutions can be analyzed, as in the American Society for Testing Materials standard methods for zinc and zinc-base alloys. Spectra of powdered solid samples can be prepared by using carbon electrodes provided with a crater of suitable size, into which the sample is packed. Ore samples and many other powdered solid materials usually analyzed in the chemical and metallurgical laboratory are more complex and varied in composition than samples of metals produced in large tonnages. 'lore preliminary work therefore is usually necessary in devising a spectrographic method for analyzing a given type of powdered sample than for analyzing metal samples, in order to use that method with confidence. The howledge that the standard samples and unknowns produce equivalent line intensities at equal concentration is the fundamental basis of any quantitative spectrographic method. On the other hand, powdered samples have an advantage over metals in that any desired number of chemical compounds can be mixed dry in any desired ratio to produce a synthetic standard. Expcrience has shown, however, that spectra of elements in finely divided compounds introduced into a standard in preparing a synthetic ore sample do not always behave in the electric arc in a manner that produces spectral line intensities similar to those observed at the same concentration in a natural mineral. In ore samples minor elements frequently are contained in the crystal lattice of larger particles of an abundant ore mineral. Their dissociation and volatilization from the sample into the arc then proceeds differently in the standard and sample, with resultant differences in intensity. During the past 10 years I have devised and applied several quantitative spectrographic methods for determining various elements in rocks and minerals in connection with studies on their geochemistry,' but the incentive has gradually changed since the summer 0. 1940 to the specific practical problem of searching for domestic sources of rare and stratcgic metals. The

Jan 1, 1949

By Samuel B. Christy

The present paper is a continuation of a study of the reductionworks of New Almaden, the first part of which was published under the title " Quicksilver-Reduction at New Almaden," in the Transactions of this Society, vol. xiii., p. 547.* Frequent reference will be made to some of the data there given. The following is an outline of the contents of this paper: I. Condensing appliances used at New Almaden: a. Brick condensers, b. Iron condensers—flues and " water-backs," c. Glass and wood condensers, d. Friction-coudensers—filters and revolving screens, e. Flues, towers, and chimneys. II. Analysis of condensing-systems. III. Temperature of condeusers. IV. Product of condensers. V. Treatment of soot. VI. Losses of treatment: a. Nature of losses, b. Composition, weight, and volume of dry gases, c. Volume of wet gases, d. Specific weight of quicksilver vapor, e. Vapor-loss at various temperatures. VII. Comparison with New Almaden practice. VIII. Comparison with results at Idria, Austria. IX. Comparison with results at Almaden, Spain. X. Future improvements in quicksilver-condensation. I. Condensing Appliances. The complete condensation of mercurial fumes in a large way presents numerous practical difficulties, familiar to all who have had to retort amalgams. In condensing the quicksilver-fumes discharged

Jan 1, 1886

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By P. V. Faragher

A metal or alloy finds its place in commerce in proportion to its ability to serve certain purposes better and more economically than other materials. While there is some overlapping of the fields of application of the various metals under discussion in this symposium, each one has its uses for which it is especially adapted. While aluminum is the most recent of the metals to enter the field, the development of the industry has been based on its peculiar properties, by virtue of which new uses for non-ferrous metals have been created. There has been substitution of this new metal for other members of the group but there has been a far greater development in entirely new fields. In common with the other non-ferrous metals, aluminum is resistant to atmospheric corrosion. It also withstands the action of many of the common chemical reagents, strongly alkaline substances being the notable exceptions. The outstanding properties on which the application of aluminum is based are its low specific gravity and its ease of fabrication into the forms in which it is used. It is noteworthy that this property of specific lightness is retained in all the commercial aluminum-base alloys. This statement does not apply to aluminum bronze; this is more properly a copper-base alloy, since aluminum enters into its composition to the extent of only about 10 per cent. None of the commercial casting alloys of aluminum has a density exceeding that of the parent metal by more than about 10 per cent., and some are actually lighter. In the so-called "strong alloys" of aluminum in which strengths comparable to that of mild steel are developed by heat treatment, the greatest increase in density is only slightly more than 3 per cent., and one of these, also, is lighter than aluminum. This property of lightness combined with the desirable mechanical properties of the alloys, makes aluminum especially suited for parts of moving assemblies where saving in power, as well as a decrease in stresses resulting from inertia and vibration, are of importance.

By Alex McCoy

SAMPLING of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines-laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. LABORATORY INVESTIGATIONS ON EMULSIFIED OIL Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. S. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy,

Jan 8, 1919

By John W. Cahn

The spinodal has long been regarded as a limit beyond which a homogeneous phase could no longer be metastable. But only recently has it become apparent that a phase beyond the spinodal would decompose by simple diffusional clustering mechanism quite different from the nucleation and growth mechanisms encountered for metastable phases. The theory of spinodal decomposition, which is based on the diffusion equation modified by thermodynamic requirements , is phenomenological, and each parameter can be measured by independent thermodynamic or diffusion experiments. The details of the theory have been carefully verified in a number of simple systems. It appears that the spinodal mechanism is commonly encountered in clustering reactions in solids and glasses. HISTORICAL INTRODUCTION The understanding of the earliest stages of precipitation in alloys has been the subject of three prior Institute of Metals Lectures. In 1932 Paul ~erica' reviewed the puzzling evidence that hardening of duralumin is completed before precipitation of CuAlz takes place and suggested that hardening occurs when the copper atoms "assemble in random groups on lattice positions of the duralumin, not of the CuAlz lattice". He called these random groups knots. This modification of his dispersion hardening theory seemed to fit all the facts, but Merica worried that the required diffusion "is just the reverse of what we deem normal; although quite spontaneous, it proceeds uphill, if you please". The reality of Merica's knots was quickly confirmed by Guinier's' and preston's3 X-ray work and these knots are today known as G.P. zones in their honor. Theoretical justification for uphill diffusion was also quickly provided by Becker and Dehlinger~ who noted that the diffusion coefficient could be negative in certain regions of phase diagrams. The boundaries of such regions could be described by a 90-year-old thermodynamic concept first described by ~ibbs' in 1877 as a limit of metastability for fluid phases, which by 1890 had received the name spinodal (see Appendix A). Spinodal in fluids is as old as nucleation theory. Both appear for the first time in the same paper by Gibbs who called the spinodal the limit of metastability. For the first 50 years, nucleation theory was forgotten and the spinodal was extensively treated in every good thermodynamics textbook.81Q The idea was simple and logical and it was accepted as part of a rigorous thermodynamic development of metastable phases, and for a while it was extensively investigated theoretically.

Jan 1, 1969

By W. O. Philbrook, K. M. Goldman, G. Derge

THIS is the third in a series of papers from the Metals Research Laboratory dealing with the transfer of sulphur across the iron-slag interface in a carbon-saturated system. The first paper' showed that the transfer obeyed first-order kinetics. The second' presented detailed evidence in support of the three-stage mechanism: FeS(Fe) FeS(slag) FeS(slag) + CaO(sing) ? CaS(slag) + FeO(slag) FeO(slag) + C ? Fe + CO. This emphasized the role of an iron-sulphur complex as the transfer agent across the interface and as an essential intermediate in the overall process. The present paper shows the influence on the process of the individual elements, carbon, silicon, manganese, and phosphorus, the alloying elements normally present and of interest in commercial blast furnace operations, aluminum, which has a pronounced accelerating influence, and nickel and copper, which are common minor impurities in the raw materials. The experimental methods and procedures for interpretation of data are the same as described earlier.1,2 Induction heated, graphite crucibles were used, and sulphur-free slag was added to the molten iron containing sulphur and the selected alloy. Slag samples were taken at regular time intervals and analyzed for sulphur and other components of interest. The authors wish to state specifically that these experiments were not intended to simulate industrial blast furnace operations. However, they do represent a study of the kinetics and mechanism of sulphur transfer at the slag-metal interface under specified laboratory control of the major variables in the system. It is believed that the results can be usefully applied to the blast furnace if consideration is given to the differences which are known to exist between the two conditions. A rigorous evaluation of the accuracy of rate studies is difficult. Recognized sources of error include sampling and analysis of both slag and metal, temperature measurement and control, selection of zero time, composition of the gaseous atmosphere over the reaction system, and extraneous sources of sulphur from the graphite crucible and reagent materials. In this study carefully standardized procedures were followed consistently in order to minimize the errors. It is believed that the reproducibil-ity of duplicate runs indicates that errors have been rendered negligible relative to the observed effects from intentional variables. For example, original experimental points for duplicate runs are shown in Figs. 1, 2, 7, etc. In most cases in this paper the drawn curves represent an average of at least two heats. The spread in sulphur values at a given time ranges from 0.02 to 0.08 pct, which is a small frac-tioi of the total values ranging up to 2 pct S in slag. In the systematic study of the influence of alloy additions, each element was added over a range of concentrations. The two slags used in this study were designated as "acid" or 1530 and "basic" or 1545. They had the nominal compositions given in Table I. Rates were measured in the temperature range 1500" to 1650°C. Data will now be presented to illustrate the various features of the study. Silicon The first alloying element examined was silicon, because its presence is unavoidable in any silicate slag system through the reaction y/2SiO2(slag) + xM?y/2Si(liq.Fe) + MxOy where M is any reducing agent such as iron or carbon. It is known that the attainment of equilibrium by this reaction is extremely slow and probably not reached in the blast furnace." The influence of silicon on the final stages of the sulphur reaction has also been studied.' It has been shown5 hat silicon increases the activity of sulphur in iron. For such reasons silicon may also be expected to influence the kinetics of the reaction. The observed effects will now be described. The general procedure was to melt 530 grams of ingot iron in a graphite crucible, 3 in. OD, 2 1/4 in.

Jan 1, 1955

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By Ted C. Briggs

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth's atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent or in the locations required by modem agriculture. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. The organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until about 1913, when the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen, at high temperatures and pressures and in the presence of a catalyst, to form ammonia. At present Chile is the only country in the world with a nitrate mining industry, and, although the mining of natural nitrates is an important industry in Chile, natural nitrates are relatively unimportant, worldwide, because of the adoption of fixed nitrogen processes. The relative amount of the world demand for fixed nitrogen that is derived from natural nitrates has declined in recent years and will continue to decline. Modern farmers are sophisticated in economic calculations such as cost to benefit ratios and, for the most part, they purchase plant nutrients which give the highest return on their investment. Natural nitrates cannot compete on a fixed-nitrogen cost basis with anhydrous ammonia and its derivative products. In a limited sense, the fixed nitrogen industry is mining the air. Modern plants use air, water, and, in most cases, natural gas to produce the ammonia that is now the key building block of the fixed nitrogen industry. To present an accurate picture of the industry, this chapter on nitrogen follows a format somewhat different from that of other chapters in this volume.

Jan 1, 1975

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By W. J. Skewes, C. T. Holland

Properly constructed stopes are necessary underground for proper ventilation and safe, healthful working conditions. Mining companies are concerned with providing the best possible stoppings at an economic cost. It is important to consider 1) proper materials, 2) construction that ensures maximum performance from the material used, and 3) keeping costs within reasonable limits for the unit operation—stopping—involved. The authors investigated all aspects of the problem and have attempted to layout a study program to provide information on all phases. Mining companies every year purchase huge amounts of material for the construction of ventilation stoppings. This material by the time it is in place in the stoppings will cost the company many thousands of dollars. In addition and more importantly these stoppings are supposed to confine air travel along certain well defined paths into areas where it is needed to provide safe and healthful atmospheres for workmen. The cost of forcing this air through the mine is large and in general increases as the total quantity increases. Consequently, if the stoppings leak, increased cost results and in addition unsatisfactory ventilation may prevail in the mine. Therefore, it is essentia1 to provide the best possible stoppings at an economic cost. When attempting to provide the best stoppings possible at an economic cost, three aspects of the problem must be considered. These are 1) getting the most suitable material for stopping constructions, 2) constructing the stopping so as to get the best performance from the material used, and 3) keeping the cost of stopping construction to a minimum for a suitable stopping. This investigation is concerned with all phases of the problem and has attempted to lay out a study to provide information on all of them. In order to develop information on the best stopping material available it seemed wise, after con- sidering the job a stopping must do, to investigate the following aspects of material used for stoppings: 1) strength in compression, 2) compressibility or yield under load, 3) porosity, and 4) permeability. To provide information on the best manner of construction the following aspects of air leakage through the stopping were investigated: 1) when the stopping is built of dry stacked materials—i.e., the joints are not mortar-laid (See Fig. 1); 2) when the stopping is built of dry stacked material and then plastered on one side (see Fig. 2); 3) when the

Jan 1, 1961

By William E. Galloway, Gary E. Smith, Christopher D. Henry

INTRODUCTION Studies relating to the Oakville aquifer as presented in this report and by Henry et al. (this volume), are part of a larger , comprehensive examination of regional and local stratigraphic, hydro- geologic, and geochemical parameters within the Oakville Formation recently completed by the Bureau of Economic Geology. The Oakville serves both as a major Gulf Coast aquifer and an important uranium host (Fig. 1). Regional and local controls on hydrodynamics and hydrochemistry have important implications for hydrochemical exploration, the establishment of premining baseline parameters, and the design of post mining restoration procedures. Investigations of the Oakville Formation were de- signed for the purpose of determining the response of the aquifer to uranium extraction and were funded by the U.S. Environmental Protection Agency under grant numbers R-805357-01 and R-805357-02. Physical Stratigraphy Physical stratigraphic analysis shows that the Oakville Sandstone, a lithostratigraphic unit deposited by a major coastal-plain f luvial system, consists of five mappable, component depositional elements (Figs. 2 and 3). Each major component element is the product of one or more rivers traversing the Miocene coastal plain. In turn, each river possessed a unique sediment load, discharge characteristics, and source terrane. Consequently, each element exhibits distinguishing geometric and compositional parameters that potentially influence the flux and hydrochemical evolution of contained ground waters (Galloway, Henry, and Smith, in preparation). The Oakvil le Sandstone, as mapped and interpreted as a lithostratigraphic unit in the study area, corresponds closely to the Jasper aquifer system, an equally well-defined Gulf Coastal Plain hydrogeologic unit (Baker, 1978). Principal surrounding hydrogeologic units include the underlying Catahoula confining system, the Jasper aquifer system itself, and the overlying Burkeville confining system (lower Fleming mudstones). The Evangeline aquifer system includes much of the Fleming Formation. The Jasper aquifer system is bounded above and below by relatively less transmissive, finer grained confining systems, although absolute transmissivity varies greatly within both the Jasper and confining units. Lithostratigraphic and hydrogeologic boundaries coincide almost exactly within the Hebbronville flu- vial axis (Fig. 3). Correspondence of geologic and hydrostratigraphic boundaries is good within the George West axis; farther to the northeast the correlation of the Jasper aquifer with units mapped as Oakville Formation diverges to varying degrees. A complete analysis of these trends and a study of the depositional facies comprising the Oakvillle are included in Galloway, Henry, and Smith (in preparation). REGIONAL HYDROGEOLOGY The stratigraphic, compositional, and structural framework of the Oakville Formation and the mosaic of interrelated depositional facies that are combined in this framework play a key role in defining the hydrogeology of the Oakville. Furthermore, a combination of climate and hydrogeology, as well as past and present socioeconomic conditions, has determined water and land use patterns within the region of Oakville outcrop. Utilization of Oakville Ground Water Stratigraphic control for determining which wells produce ground water from the Oakville aquifer was established by preparing structural and isopach maps of the Oakville Formation using regional electric log cross sections. Surface elevation and screened interval data (or total well depth, if open-hole completion techniques were used) from each water well, combined with the stratigraphic data, allowed accurate assessment of the producing aquifer for individual wells. Information on well and screen depths, water levels, and usage of water from

Jan 1, 1980

By J. L. Huitt, IM. L. Slusser, E. E. Glenn, M. L. Slusser

This paper is concerned with: (1) an analysis and interpretation of the filtration characteristics of drilling muds on filter paper, and (2) an interpretation of early stage "filtration" on consolidated synthetic porous media, herein referred to as the "surge loss" period. It is shown that water-loss data can be plotted so as to disclose the existence of a surge period, a non-uni-form cake thickness period, and a constant pressure filtration period. The same periods occur during exposure of consolidated porous media to muds. The data on consolidated porous media indicate that: (1) mud particles bridge pores inside porous media during the surge period, and (2) "filter cake" build-up inside porous media occurs during subsequent filtration. The data also show that the surge loss increases with sample permeability and with pressure differential. INTRODUCTION The phenomenon of mud filtrate invasion into porous sands of a drilling well has been recognized for many years.1,2,3,4 Part of API Code 29 is concerned with the filtration testing of a drilling mud to yield data on this subject. In a number of investigations "plastering properties" of muds were studied,5,6,7,8 "plastering" apparently meaning cake forming properties. In such studies the characteristics (thickness, permeability, and toughness) of the cake and the rate at which the liquid phase of the mud was separated from the solids (filtration rate through the cake, commonly referred to as water loss) were measured or at least considered. From the standpoint of its effect on well productivity, filtrate invasion into "clean" water-wet pay sands (i.e., those containing no clay minerals) may not necessarily be a serious problem. An increase in water saturation in the zone immediately around the wellbore would cause loss of oil permeability. However, in such a system, much of this water may be removed by oil production. If filtration occurs into "dirty" sands (i.e., those containing appreciable clay minerals), clay swelling or other mechanisms may cause losses in oil permeability which cannot be overcome by oil production.'.' The phenomenon of mud particle invasion into the pay sand of a drilling well was considered to be a possible serious factor in the early days of rotary drilling. Opinions varied as to whether drilling fluids "mudded up" and "sealed" oil sands. In 1932 Rubel,9 Gill,10 and Parsons," in separate papers, presented differences of opinion together with some laboratory and field data concerning loss of oil production caused by drilling fluid invasion into pay zones. These papers, and the discussions, furnish a large background on this subject and indicate the very clear thinking of many men at a time when petroleum production technology was in its infancy. Jones and Babson,6 and Silent,' experimentally found that the depth to which mud particles invaded water-saturated sand packs was small (no greater than 1/16 in). Arn-quist12 in 1937 observed loss of water permeability due to invasion of mud particles into water-saturated, consolidated, sandstone samples. Williams and Cannon5 studied the filtra-tion properties of drilling muds and mentioned "sludge" which penetrated a short distance into the water-saturated filtering medium (sand pack). Byck5 concluded that formation permeability had no effect on the plas-

Jan 1, 1958