Search Documents

By Edgar Bain

OF THE important phenomenon of the hardening of steel, Professor Sauveur1 says: "It would seem as if the methods used to date for the elucidation of this complex problem have yielded all they are capable of yielding and that further straining of these methods will only serve to confuse the issue, the point having been reached when this juggling, no matter how skilfully done, with allotropy, solid solutions, and strains is causing weariness without advancing the solution of the problem.. The tendency of late has been to abandon the safer road of experimental facts and to enter the maze of excessive speculations, in which there is great danger of some becoming hopelessly lost. The conclusion seems warranted that new avenues of approach must be found if we are to obtain a correct answer to this apparent enigma. With some degree of fitness we may say, this of other problems. It seems likely that one of the new avenues of approach to many metallographic problems is the study-of crystal structure, or more accurately, the atomic arrangement by means of the X-ray spectrometer. The crystal structure of some materials has been carefully worked out by the mineralogist, but his methods are, in general, unsuited to commercial metals and a method that yields even better information is at hand as the result of work on the diffraction of X-rays by Laue and the Braggs2 and later by Hull,3 St. John, and others. It should be understood that the contour of free crystals, which is the subject of measurements by the crystallographer, is the result of the atomic structure and, in general, bears a simple and obvious relation to it. The use of the X-ray spectrometer4 has been described frequently, so the procedure will not be given here.

Jan 2, 1922

By Research Staff ? Verde Copper Mines

FLOTATION is now commonly practiced in alkaline ore pulps, yet little is known regarding the action of the alkaline solutions on the ore particles beyond the fact that films of oxidized material form. We wish to chronicle our discovery of the presence of soluble reducing agents in alkaline ore pulps of the United Verde, and present some data on lime consumption. During the grinding and flotation of a pyritic ore containing small amounts of ferrous sulfate and other soluble salts, an excess of lime was added to precipitate the salts, and filtered samples of the solution were titrated with standard permanganate solution. Even in pulps of high causticity an appreciable permanganate titration was always obtained, in spite of the fact that the solutions were shown to contain little iron. Investigation of the cause brought about the discovery of several previously unsuspected compounds in flotation pulps made from pyritic ore. Not only the reducing agents present had to be identified, but also the amount of dissolved oxygen, and a survey was finally made of the free oxygen content and reducing agents of the mill pulp in the concentrating mill at Clarkdale. A great many compounds might form, caused by oxidation of pyrite or other metal sulfides or by reaction between a lime solution and pyrite. The most probable compounds considered were calcium sulfides; polysul-fides, thiosulfates, and polythionates. Later it was discovered in the literature that in alkaline pulp polythionates do not exist and if introduced. are decomposed into sulfites and thiosulfates.1 Any precipitated sulfur is changed by alkali into thiosulfate and polysulfide. Sulfites and sulfides react to form thiosulfate, so that in the end it is possible to have in an alkaline solution only thiosulfate and an excess either of sulfide or sulfite. Confirmatory tests were made and it was finally established that the alkaline mill pulps made from the United Verde ore contained

Jan 1, 1929

By R. P. Heuer, Paul M. Tyler

THE literature on refractories, although fairly extensive, is so scattered through books and periodicals as to be difficult of access to the general reader and most of the individual papers serve merely to illuminate some particular phase of the industry. Two general treatises by American authors8.16 are available, also the somewhat older works by a well-known British authority, 12,13 but these make their appeal to the technically minded ceramic engineer. Another small group of publications deals with the use of refractories, mainly in the iron and steel industry.1, 3,5,6,11,15 Raw materials utilized by the refractories industry have been covered by sundry books and articles. For the relatively nontechnical reader and economist, however, there appears to be no single review that purports to describe the industry as a whole. Furnace linings and other products that are classed as "refractories" are designed primarily to withstand high temperatures but this important property is by no means the only requirement; a suitable refractory material must likewise withstand slagging (chemical' action), abrasion (physical wear), and spalling, as well as the various other stresses and physical phenomena induced by heat, of which softening or incipient melting is only one phase. Nevertheless, subject to these highly practical considerations, the definition of a refractory material is based upon temperature resistance. Broadly speaking, any material that shows obvious signs of fusion after being heated slowly to 1500°C (2732°F) cannot be classified as a refractory material. The characteristic properties and requirements of refractory materials are conveniently summarized in Fig 1, prepared on the American Refractories Institute Fellowship at Mellon Institute, Pittsburgh, Pennsylvania. Most of the factors of service and properties of refractories given in this chart are interdependent and are greatly affected in degree by the functions of temperature and time. The factors in the chart are believed to cover the commoner questions.

Jan 1, 1949

By Enrique Hauser

FIRE-DAMP is a mixture of methane with other inert gases or combustible gases. The inert gases in question are carbonic acid, water vapor, nitrogen, etc. The combustible gases are hydrogen, ethane, etc. The study of the properties of fire-damp, therefore, becomes a study of the properties of methane and the influence on its properties of the different gases we have mentioned. Characteristic Properties of Methane 1. Respirability.-Methane being a paraffin is characterized by its weak chemical affinities. From the physiological, point of view one could substitute it for nitrogen of the air at least momentarily, without experiencing any difficulty in breathing the mixture consisting of 21 per cent. 02 + 79 per cent. CH4. I .have tried this on myself, making the gas exhaled -from the lungs burn subsequently in a Bunsen burner.1 From the chemical point of view, this weak affinity permits the gas to be burned in certain circumstances with hydrogen and oxide of carbon in an oxygenated mixture, with the result that the last two gases achieve only a fractional combustion. This practice has been utilized with success in the methods of analysis which I have perfected and which I describe later in this paper. 2. Retardation of Flashing Point.-A characteristic property of methane is its retardation of flashing point, noted by Davy in 1816 and studied by Mallard and Le Chatelier in 1883.2 Taffanel and Le Floch have recently confirmed these results.3 Let us recall the nature of this retardation:

Jan 2, 1916

By Robert B. Fulton

It is a pleasure to talk to you about the world economics of industrial minerals on this occasion of AIME's 100th anniversary. In order to fit this topic into the time and tenor of such a session as this where you are hearing subjects equally broad in scope one after the other, I will deal with the subject through the medium of eight minerals selected to illustrate import- ant economic factors. I must admit to some bias in the selection, since I picked personally familiar ones to elucidate facts of life in the industrial minerals business. It is a very interesting field, different in many respects from metals and certainly far different from petroleum. The minerals chosen are celestite, diamond, fluorspar, salt, sulfur, ilmenite, rutile and zircon. Celestite The market for celestite is mainly in the U. S. where it is consumed in the manufacture of strontium compounds for red-colored flares and other pyrotechnics, for the production of electrolytic zinc, for glass manufacture, and for the manufacture of ceramic ferrites. Smaller markets exist in Europe and Japan. Production comes from England, Mexico and Spain, and a new mining operation is being started in Nova Scotia. There is no significant production in the U. S. nor in the other principal consuming countries, except England; so it is mainly an international commodity. Celestite illustrates many of the factors important in the economics of industrial minerals. To have a marketable product, grade and freedom from deleterious elements are important for materials used by the chemical industry. In the celestite used to make strontium nitrate, calcium is the most objectionable of the commonly associated cations. Selling price is adversely affected because nitrate manufacturing costs are greatly increased if calcium is pre sent, hence less can be paid for the raw material. Meeting specifications can add significantly to the vendor's cost; hence a balance must be struck between the producer's capability and the consumer's requirements, permitting a reasonable profit for both. Sizing of industrial mineral products is often important to the consum-

Jan 1, 1971

By S. Beatty

RECENT experimental results' on the superconductive properties of vanadium indicate that the magnetic behavior of the metal is greatly affected by internal strains caused by mechanical work, and particularly by oxygen and nitrogen impurities. These result in an increase in the hardness of the metal such that metallurgists' have used hardness as a measure of the impurities. An increase in the impurities should also be reflected in a change of lattice parameter with increasing impurity content. The lattice parameter of vanadium prepared by the thermal decomposition of the iodide has been determined by two workers. Neuburger3 obtained a value of a, =3.0338 ± 0.0003A for the body-centered cubic lattice by means of the powder method. The work of Katelaar is referred to by van Arkel4 in which a value of a0 = 3.025 is given. Four samples were used for this investigation. Sample A, the vanadium of the highest purity in the group, was obtained by means of the thermal decomposition of vanadium diiodide and deposited on a 3 mil diam tungsten filament in the form of crystals. The second sample, labeled B, was obtained by the calcium reduction of the pentaoxide at a sufficiently high temperature to give a melt. A third sample, C, was obtained in the same manner as B but remelted in a pure argon atmosphere. The last sample, D, was prepared by the calcium reduction method and the fine powdered vanadium was then sintered by means of applied heat and pressure. Samples A, B, and C were thus essentially free of mechanical strain in their preparation. Sample D was annealed in a high vacuum at 800°C. The samples were prepared for X-ray diffraction analysis such that all additional strain by cold work or by contamination with oxygen and nitrogen was kept at a minimum. Powder obtained from filings was deemed unsuitable since this would require annealing to get rid of the cold work. A heat treatment up to 1000°C at 10-6 m pressure might still increase the impurity content by means of adsorbed oxygen from residual gas in the vacuum chamber. The most satisfactory samples were prepared for back-reflection film techniques. Samples were cut to size, etched with hydrobromic acid, and mounted in Bakelite. They were then lightly polished on 3-0 paper and lightly etched. Chemical and Hardness Analysis of Samples Spectrographic analyses were made of the four samples and indicated similar metallic impurities for the group. The major metallic impurity in each sample was iron, which was less than 0.01 pct. The sum of the other metallic impurities was approximately 0.1 pct. The carbon content was assumed low by virtue of the methods of sample preparation. The principal impurity difference between the samples was in the oxygen and nitrogen content.

Jan 1, 1953

By H. H. Vogel

THIS paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. CHARACTERISTICS OF THE ORE The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾ mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3A12 (Si04)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to 12 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crystals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3.07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive. FORMER OPERATIONS Mining operations have been carried on for 60 years. Until 1023, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By C. DeWitt Smith

"It just looks like everything is doing fine but humans," wrote Will Rogers fifty years ago. "Animals are having a great year, grass was never higher, flowers were never more in bloom, trees are throwing out an abundance of shade for us to loaf under. Everything the Lord has a hand in is going great, but the minute you notice anything that is in any way under the supervision of man, why, it's cockeyed." Do these words from two generations ago apply to oil shale? The United States has been blessed with deposits that can yield synthetic crude oil at a cost competitive with natural crude oil-under present economic conditions and with existing technology. Yet, the oil shale program is cockeyed because of the artificial obstacles that have been placed in its path "under the supervision of man." But more about this later. For the moment, let's focus on...

Jan 10, 1974

By Frederic Benard

The treatment of Balbach-Thum slimes at Copper Cliff by the Ontario Refining Co, is of interest because it differs considerably from methods usually employed for the recovery of fine gold from parting-plant slimes. Owing to the comparatively high percentages of palladium and platinum, wet methods are used to remover the greater proportion of these metals before electrolytic refining in the Wohlwill cells. The Plant The platinum-metals department, Wohlwill room, and gold-melting room extend along the north side of the silver refinery and are separated from the parting plant by a glass partition (Figs. 1 and 2). The platinum-metals department resembles a laboratory built on a large scale, with the various pieces of equipment laid out on terraces to facilitate handling. Because of the corrosive nature of the solutions, chemical stoneware is used throughout. Elevation of acids is accomplished by means of Mariotte bottles. On the top level are three steam-jacketed stoneware kettles of 50-gal. capacity, also a packed tower. One kettle is used for digesting the slimes while the remaining kettles are used for precipitating the gold. The dissolver is equippcd with a treated concrete hood, which is connected to the flue system. Gases are drawn off through the packed tower by means of a 6-in. stoneware exhaust fan. A 15 per cent solution of sodium carbonate is continually circulated through the tower. On the intermediate level are two suition filters, one for removing silver chloride and the other for the gold sand. The filter medium consists of an asbestos pad covered with a filter paper on which is a layer of twill. On the bottom level are two rectangular cementation tanks, 24 by 48 by 24 in. deep, and a suction filter used for removing the platinum-metal concentrates. The circulating pump for the packed tower is also here. Suction is provided by a vacuum pump having a capacity of 8 cu. ft. at 20-in. vacuum.

Jan 1, 1944

By C. E. Julihn

Technology concerns the ways of doing things; mineral technology the ways of performing operations required for obtaining minerals from the earth and extracting their valuable constituents for man's use. At any particular time, technology is relatively fixed, as everyone tries to adopt the way of doing things that has proved most profitable; but improvements evolve from minor changes here and there, and occasion- ally entirely new methods are discovered. Technologic improvement thus characterizes any long-time view of the mineral industries. Its test lies always in reduction of costs; there is no other incentive for the adoption of new methods. Reduction in cost of producing metal from ore decreases, in turn, the amount of metal that must be obtained from ore in order to pay for its production. An advancing technology thus is characterized by utilization of ores of lower and lower grade. A very important result of this is an increase in the gross quantity of metal obtainable at any price level, since the earth's crust contains vast amounts of very low-grade ores and relatively insignificant amounts of very high-grade ores. Technologic advances have, therefore, been the means of rendering the metals both cheap and abundant. Though concern as to possible exhaustion of the world's ore deposits is warranted, it is conceivable that a transcendent technology of the future might supply metal requirements from what we

Jan 1, 1932

By Walter Renton Ingalls

Vague references to tin-deposits in Mexico are scattered throughout technical literature, and that country has been looked to as a likely source of a part of the world's supply of till at no very distant date; but thus far nothing but occasional small lots have come forward, so that the notion has arisen that these mines are either mythical or unworkable. So far as I am aware, there has not yet been published any description of the tin-deposits of Mexico except a few brief references; and this paper, based on a study of them made in 1892, is therefore offered.

Jan 1, 1896

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/1 6 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible. to maintain in stock marbles of the color, size, and thickness called for,, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill. such, orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By Donald J. Worth

INTRODUCTION Minera Real de Angeles makes a very interesting case study in more ways than one. To begin with, it represents the first time a bulk silver deposit has been put into production in Mexico. Second, the feasibility and financing stage spanned a period when the silver price ranged from $4 to $40 per ounce. Third, there was a major devaluation of the peso and a financial crisis in Mexico at completion of the project. Fourth, the composition of the partnership (a major Canadian mining company, a major Mexican mining company and the host government's own mining entity) is worthy of note. This paper gives considerable background on the project and how it came to fruition. The political risk aspects and how the major provider of funds perceived Mexican risk at the time of decision to participate and afterwards are highlighted. LOCATION AND HISTORY The Real de Angeles deposit is located at an elevation of 2300 meters in Central Mexico in the State of Zacatecas (Figure 1). The closest village is Noria de Angeles, three kilometers to the north. The closest cities are Aguascalientes, Zacatecas and San Luis Potosi. The first-mentioned is one hour to the southwest by automobile over good roads. Exploitation of the vein outcrops probably began towards the end of the sixteenth century by the Spanish. Evidence of past mining activity is shown by numerous shafts, manways, dumps and ruins. Also, there were remnants of two rudimentary concentrating mills now obliterated by pit development and in the nearby town of Noria de Angeles the ruins of a small smelter still exist. Compania Minera Gamma, an affiliate of a major international mining company, investigated Real de Angeles from 1969 to 1971. Its evaluation program included 20 drill holes and comprehensive geological engineering and metallurgical studies. The results were not encouraging and the option on the property was dropped. In late August 1973 geologists representing Placer Mexicana which was later renamed Explomin were advised of the availability of the property and liked the prospects sufficiently to make an option payment soon due and to agree to outright purchase by year-end. A series of 34 holes were drilled by Explomin and a preliminary study indicated that the prospect had mine-making potential if the silver price was right. [ ] DESCRIPTION OF THE PROJECT Real de Angeles is best described as a large, low grade open pit silver mine because at today's prices approximately 70% of the realizable revenue is derived from that metal. One must also keep in mind that the operation produces two concentrates - a lead concentrate with high silver content and

Jan 1, 1985

By Robert H. Richards

The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G. A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. 11. The First, or Coarsest, Section of the Field. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a definite ratio. There are three natural sieve-scales: 1, progressing by doubling the width of the hole for each suc-

Jan 1, 1908

By H. S. Gibson

A PROCESS that has come to be known locally as "multistage stabiliza-tion" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It con-sists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation, (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1939

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose. Ferrites and Marmatites The name "ferrite" has been given to the compound of zinc and iron which has the formula Zn0.Fe203. Among the questions pertinent to this subject are those involving inherent or natural ferrite, and also the synthetic or artificial variety. The inherent or natural product is formed when the mineral containing iron and zinc sulfides isomorphously crystallized is subjected to oxidation at roasting temperature. These isomorphously crystallized minerals are known, mineralogically, as marmatites, and contain ZnS and FeS in ratios of 2 to 1 up to 5 to 1 respectively. The zinc and iron sulfides form a definite mineral. They are firmly attached to each other and form common contact planes through which diffusion of the entities occurs during the roasting process. This diffusion of the molecularly intimate entities produces, during roasting, the compound referred to as ferrite, in proportion to the amount of iron originally present in the marmatite. For example, a marmatite from British Columbia containing 9.739 per cent. Fe and 56.87 per cent. Zn corresponds with the mineral having the formula 5ZnS.FeS. The ferrite produced in roasting, which has the formula ZnO.Fe203, contains 27.07 per cent. Zn and 46.40

Jan 1, 1929

By Ray W. Arms

DRY cleaning, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc. Air Stratification In all of the above groups of air separating devices, the same phenomena are found as exist in water concentrators; that is, free settling will be found in some and hindered settling in others, with a complex action on the reciprocating tables similar to the wet tables. The experimental value of the settling ratios of particles in air has never been determined but, following the formulas given in Richards'

Jan 1, 1924

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i, e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any, rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By William E. Ford, Edward Salisbury Dana

Normal phosphoric acid is H3P04, and consequently normal phosphates have the formulas R3PO4, R3(P04)2 and RPO4, and similarly for the arsenates, etc. Only a comparatively small number of species conform to this simple formula. Most species contain more than one metallic element, and in the prominent Apatite Group the radical (CaF), (CaCI) or (PbCI) enters; in in the Wagnerite Group we have similarly (RF) or (ROH).

Jan 1, 1922