Search Documents

By L. G. Jones

An approximate method of calculation is developed in this paper which allows duplication of radial unsteady-state gas flow computer results where Darcy's law applies, such as those reported by Aronofsky and Jenkins and Bruce, Peaceman, Rachford, and Rice. Moreover, the new calculation method can be used to obtain results for radial unsteady-state gas flow obeying the quadratic flow law proposed by Duwez and Green. Means are discussed for predicting well behavior at single or superimposed flow rates in finite or infinite reservoirs, determining reservoir rock properties from well-test data, reproducing and interpreting back-pressure test data, and determining the radial extent and reserves of gas reservoirs from well-test data. Example calculations are presented for gas flow following both Darcy's law and the quadratic flow law. INTRODUCTION Since the publishing of U. S. Bureau of Mines Monograph 7,1 most gas-well testing methods have been based on the equation q = y (pl2 - pw2)a, where q = production rate, pl and pw, are formation pressure and sandface pressure, respectively, and y and a are constants to be obtained from test data. These methods, used for predicting both deliverability and "open-flow" capacity of gas wells, have been useful and accurate in many cases but unsatisfactory in others. Even at best, however, they do not supply information about the formation or lead to an understanding of nonsteady-state gas flow in porous media. Many theoretically based studies2-4 of gas flow obeying Darcy's law have been made.' Since the partial differential equations which result from combining Darcy's flow law with the continuity equation are nonlinear, most of the published research consists of either numerical solutions or analytical solutions for linear approximating equations. Such solutions have been of limited value in field work due to their unhandy form and their failure to correlate most field data. There is evidence5,6 which indicates that Darcy's law is inadequate to describe gas flow at some flow rates of practical interest. A quadratic flow law: which reduces to Darcy's law at low rates, is more successful in accounting for experimentally observed behavior. This flow law has been applied successfully to a few hypothetical reservoir cases in work which has recently been published.10 However, these numerical solutions of the equations involved have been successful only on a special analog computer. Routine applications to field cases would be awkward and have not been attempted. The present paper describes an approximate method for computing nonsteady-state gas flow solutions which has been completely successful in predicting the results for both Darcy flow and quadratic flow obtained by elaborate numerical methods. The new calculation method allows determination of the observable variables in gas-well testing at constant rates. It is similar to the scheme of using a succession of steady states suggested by Muskat7 in that it makes use of steady-state and material-balance equations. It also is similar to the work of Aronofsky and Jenkins2 in that the new method includes Aronofsky and Jenkins' stabilized flow equation as a special case. It improves upon both of these calculation schemes in that it accurately describes all portions of reservoir history and suggests means of determining reservoir rock properties from well-test data. This paper deals only with production from a reservoir, in which case the rate is defined as being negative. The reservoir studied here is a homogeneous, disk-shaped porous body of uniform thickness, with all boundaries sealed except the inner radial boundary of the well.

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-' pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.' and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By R. Hoffmann

THE Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. FIG. 1.-DAILY CAPACITY OF WAELZ PLANTS RUNNING OR BEING ERECTED. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper-Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. -The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928

By A. J. Phillips, C. G. Grant, Wm. B. Price

Admiralty nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price' described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.~ A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimorr & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various a~ilounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by iiielting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of thcsc castings was polished and etched for examination. The castings were not homogenrous solid solutions, but showed the usual cored structure associated with cast alloys. Howcvrr, frorn an exarrlination of these sections we roughly determined

By Richard D. Hagni

Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in millproducts. The mill dressing engineer should be more aware of the types of beneficiation problem that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations ofthe mineral constituents of an ore or mill product can be visually determined. This advantage provides solutions to many beneficiation problem. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in flocculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 1, 1979

By Carl E. Swartz

For many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931

By Bradley Stoughton

The regular, bottom-blown Bessemer converter of the present day is a modification of previous forms, and most of the latest proposed modifications of it are merely returns to former types which Ressemer discarded. That he tried almost every conceivable method of blowing iron, with tuyeres at almost every possible position or angle, is well known; and it is to be supposed that he was familiar with the advantages of each type, since he finally settled on that form which has not been improved upon hitherto, for the purposes for which converters will generally be used. Modifications have been tried along two lines: In the arrangement of tuyeres, and in the manner of carrying out the process with tuyeres still blowing vertically upward through the bath. While they have all failed in general competition with the regular modern type of vessel, some of them have found special fields in which they have held their own. The most notable example is in the steel-casting industry, and especially in that part of it concerned with the manufacture of castings which require very hot or very fluid metal, or supply a demand of constantly varying physical or chemical requirements. In this industry the small converters occupy a field between that of the crucible-process and that of the open-hearth process, arid have won a place for themselves in France, England, America, Russia and other countries, which they bid fair to retain until either a new method is discovered of producing cheaply very hot, fluid steel, or the open-hearth process is so improved that very hot steel may be made with it at lower cost of repairs to lining arid roof.

Jan 1, 1903

By D. Walton, B. Chalmers

A preferred orientation is known to occur frequently in the columnar zone of castings. This has been attributed to a preferred direction of growth. However, no satisfactory mechanism was proposed by which the preferred direction of growth led to the preferred orientation. The purpose of this work has been to establish this mechanism. It has been found that in general the observed preferred orientations only develop when the preferred directions of growth reveal themselves by dendritic growth. A mechanism based on this premise is found to be in agreement with the experimental data obtained in the course of this work. WHEN a liquid metal is allowed to solidify in a mold, it usually freezes in three stages, distinguished from each other by the size and shape of the grains. The first zone to freeze (the chill zone near the mold wall) consists of relatively fine grains that are equiaxed in shape and random in orientation. The next zone consists of crystals that are elongated in the direction of heat flow, i.e., normal to mold wall. These crystals are much larger in cross section than the crystals of the chill zone and have a very strongly preferred orientation. This is the columnar zone. The final zone, which is absent in very pure metals, is again equiaxed and randomly oriented, but usually has a much coarser grain size than the chill zone. The purpose of this study is to describe and account for the crystal size and orientation in the columnar zone. The occurrence of a preferred orientation in the columnar zone is well known, and in 1940, Greninger' suggested that it is apparently related to dendritic growth although at that time the only data were for metals with the face-centered-cubic structure. Table I shows that the direction of dendritic growth and the crystal axis that follows the heat flow direction coincide in all cases so far studied. The term "dendritic growth" is used here to represent the branched type of morphology that is characteristic of growth into supercooled melts.' In addition to the supercooling which is necessary before nucleation will occur at the mold wall, the necessary supercooling for continued dendritic growth can be provided in a mold by heat flow into the already formed solid at an interface whose Liquidus temperature is depressed by an accumula-

Jan 1, 1960

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By A. B. Cox, L. W. Wark

In the paper on the development of the flotation process at Broken Hill (Australia) prepared by the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy and published in its Proceedings for 1930 (N. S. 80), it is stated that the concentration of ores by flotation has been established on a commercial basis in Australia since 1904 and that differential flotation was practised at Broken Hill in 1912. Since then, progress in flotation practice throughout the world has been rapid, and during recent years the knowledge of the reactions between comparatively modern so-called chemical promoters or collecting agents and the mineral surfaces has been broadened by the published accounts of many investigators, particularly those working in American universities. Because of the benefits the Australian mining industry has derived from the flotation process, it was felt that the industry should take some part in the efforts that are being made to extend the knowledge of the principles on which the flotation process is based. Accordingly, early in 1930, three Broken Hill mining companies—the Broken Hill South, the North Broken Hill, and the Zinc Corporation—together with the Electrolytic Zinc Co. of Australasia, Ltd., and the Mount Lyell Mining & Railway Co., established a laboratory in the chemistry department of the University of Melbourne for the purpose of investigating the principles underlying flotation. Subsequently, the Burma Corporation, Ltd., expressed a desire to cooperate. The two authors are directly employed and controlled by these six organizations, and the cost of the investigation is divided equally among them. The research has been carried out under the general direction and in close cooperation with Harry Hey, chief metallurgist for the Electrolytic Zinc Co. of Australasia, Ltd., and the authors desire to place on record their indebtedness to him for his ever willing help and constructive criticism. After an extensive search of the literature, it was decided to determine in a preliminary investigation whether the effect of chemical collectors could be evaluated quantitatively by the "contact-angle" method. This preliminary investigation showed that with the bubble machine of

Jan 1, 1935

By George Rice

THE subject of dust explosions in coal mines first appears in the Transactions of this Institute following the first great mine disaster that happened in bituminous mines of the United States. This was the Pocahontas explosion, which occurred Mar. 13, 1884, causing the loss of 112 men. The operating company wisely asked the technical assistance of the Institute, requesting that a committee be appointed to investigate and report. This committee consisted of Messrs. Bramwell, Buck, and Williams, who, after careful study, reached the conclusion that the explosion was due "either to dust alone or to dust quickened by an admixture of fire-clamp too slight for detection by ordinary means." This is perhaps the first time in this country that coal dust was considered to be the chief agency in a mine explosion.. The report is given in the Transactions, vol. xiii, p. 237 (1885). It is particularly worthy of note that the committee called attention to "the necessity of full-sized tests and systematic experiments. " In the same volume of the Transactions, there is a most interesting paper reviewing the literature relating to coal dust, by E. S. Hutchinson, entitled Notes on Coal-Dust in Colliery Explosions. Mr. Hutchinson gives a historical account of observations on the part played by coal dust in mine explosions, beginning with Messrs. Lyell and Faraday's report on the Haswell colliery explosion in 1844, in which it is said "much coal gas had been made from this dust in the very air itself in the mine by the flame of the firedamp, which raised and swept it along, and much of the carbon of the dust remained unburned only from want of air." The subject lay dormant until 1875 when William Galloway began some coal-dust experiments in a small gallery at a mine in South Wales of which he was manager. At that time he considered the presence of firedamp necessary for continued propagation of a dust explosion; but in 1884, the year of the Pocahontas disaster, he stated that no earlier author-than himself had credited coal dust with being a principal factor in mine explosions, relegating firedamp to a secondary place.

Jan 10, 1914

By J. D. Testerman

A statistical technique to identify and describe naturally occurring zones in a reservoir and to correlate these zones from well to well is described. The technique is particularly useful in describing a reservoir where cross flow between adjacent strata is important in determining reservoir behavior. Although it has been used primarily for permeability zonation, the technique is general and can be used to correlate any reservoir property or related data, such as the information contained in well logs. INTRODUCTION One of the first problems encountered by the reservoir engineer in predicting or interpreting fluid displacement behavior during secondary recovery processes is that of organizing and using the large amount of data available from core analysis. Permeabilities pose particular problems in organization because they usually vary by more than an order of magnitude between different strata. Due to the sheer volume, it is almost always necessary to group data and to use an average value to represent a number of measurements. Perhaps the most common method now used to group permeability data is the capacity-fraction technique, which ranks permeabilities in order of magnitude, regardless of the physical location of the permeabilities within the reservoir. The cumulative per cent capacity is plotted against cumulative per cent thickness. This plot is divided into an arbitrary number of zones, generally of equal thickness. Five zones (or averaged groups of data) usually are obtained, each of which is treated as homogeneous in subsequent calculations. The division so obtained has no physical meaning; strata in the same zone, calculation-wise, are usually not adjacent in the reservoir. Reservoir engineering techniques being developed will handle crossflow that occurs between adjacent communicating reservoir strata because of imbibition and gravity segregation. Since crossflow occurs between physically adjacent layers within the reservoir, a new zonation technique recognizing the actual location of strata within the reservoir is necessary. Similarly, the recognition of natural zones is important for predictions of oil recovery by processes involving diffusion. One such process is miscible displacement, where predictions of lateral diffusion within the reservoir must recognize the actual location of the invaded zones in relation to the rest of the formation. Natural zones must also be adequately recognized to account for heat transfer within the reservoir during thermal exploitation. Because of the complexity of the problem, statistics appear to offer the only practical hope of dividing a reservoir into physically-meaningful natural zones. This paper presents a statistical technique for identifying these natural zones and for ascertaining which ones are likely to be continuous between adjacent wells. The zones defined have minimum variation of permeability internally and a maximum variation between zones. The technique is general and can thus be applied to reservoir properties other than permeability. The method will guide the reservoir engineer in estimating which zones are likely to be continuous between wells. However, a statistical correlation based on permeabilities in two different wells is no guarantee that the zones so defined are, in fact, continuous. Rather, the assumption of continuity must be consistent with geological data concerning the depositional environment, as well as justified on the basis of engineering judgment in combination with statistics, just as judgment is required with conventional zonation methods. CALCULATION PROCEDURE The reservoir zonation technique is a two-step operation. The steps are individually described, and a sample calculation is presented in the Appendix. ZONATION OF INDIVIDUAL WELLS First, the set of permeability data at a single well is zone, into Zones. These zones are selected so that variation is minimized within the zones and maximized between the zones. The equations4,6 used to zone the data are where B = the variance between zones, , = the number of zones, i = the summation index for the number of zones, j = the Sumation index for the number of data within the zone, mi = the number of data in the ith zone, k,. = the mean of the permeability data in the ith zone, k . = the over-all mean of the data in the well, W = the pooled variance within zones, N = the total number of

By F. X. Tartaron

The comparison of actual energy of comminution with theoretical surface energy presents a wide gap. On the other hand, Solid State Theory presents a viewpoint that places actual energy of breakage in understandable relationship with the theoretical strength of materials. Therefore the physical background of comminution theory favors Kick's Law. A11 discussions of comminution theory appear farfetched when comparison is made of the actual energy of crushing with the energy input called for by thermodynamic theory. Quoting Taggart:' "The work required to crush halite was of the general order of 0.10 kg cm per sq cm of new surface produced (based on air percolation) whereas the theoretical energy of this new surface, based on thermodynamic calculation by a number of investigators is 1 x 10'4 kg cm per sq cm or the work expended was 1000 times the new surface energy — an indicated crushing efficiency of 0.10 pct." It is frustrating to probe into comminution theory with the prospect that the energy one is measuring is 99.9 pct waste energy. Do the laws of comminution deal with energy consumed by mineral breakage or with waste heat energy? There seems to be something wrong. Solid State Theory may provide the answer. The following statement is particularly apt to the situation: "The fundamental fact about metals and indeed all materials, is that they are much weaker than they should be. By this, we mean that if the stress required to cause a given plane of atoms to slip past a neighboring plane is calculated from basic atomic and Solid State Theory, the resulting number is some 1000 times too large to be accounted for by errors in approximations or assumptions. We know now that this is due to dislocations, and we even have a fair understanding of the details of the process by which dislocations make a crystal weak. An intriguing possibility which suggests itself, results from the discovery of very minute metallic crystals which are apparently free of dislocations and which have a strength approaching the ideal value for a perfect crystal." Here we have an extraordinary reversal of the situation. The actual energy for breakage is only one-thousandth the theoretical instead of 1000 times as given by Taggart. But the theoretical energy presented by Solid State Theory is the binding energy between atoms (or ions) in a crystal lattice. This is the kind of energy envisaged by Kick's law. The surface energy or the other hand corresponds to Rittinger's law. Comparison of theoretical with actual, on the basis of surface or on the basis of Rittinger's law, seems to present an absurdity; yet Rittinger's law is confirmed by an impressive array of experimental evidence. Comparison of theoretical and actual on the basis of Solid State Theory or, in other words, on the basis of Kick's law seems reasonable; yet there is not a scrap of evidence to verify Kick's law. The situation appears paradoxical, but the developments in the next section of this paper show that the paradox is a hint to a strange turn of events. ENERGY-WEIGHT FRACTION FUNCTION charles3 has presented a final equation showing the relation of energy consumed in comminution to size of product n{-1) a-n + 1 E is energy, C is proportionality constant, a and n are constants and k is the coarsest size in the ground product (size modulus). In the course of study of a large amount of experimental evidence, Charles discovered that in the general case, a-n + 1 approximated zero. For some reason, a and n differed only by unity. But if a—n + 1 = 0 within experimental error, then it is obvious that Eq. 1 states that it requires an infinite amount of energy to grind any sample to any size. This is a case where nature gives an absurd answer to a man-made mathematical equation, hence something is wrong with the equation. An adjustment must be made to fit the equation with experience. TO reveal the nature of the adjustment, the differential equation preceding the second integration in Charles' group of equations is given When Charles integrated the quantity xa-n it was almost impossible for him to realize that he was dealing with a special case of integration and that

Jan 1, 1962

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper' described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern' and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel'kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi'" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,'' consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By John C. Shyne, Eric R. Morgan

BORON as a hardenability agent of commercial importance has been the subject of extensive study in recent years. It has been suggested in the past that boron increases hardenability by combining with nitrogen, thus rendering it innocuous.&apos; More recently it has been proposed that boron increases hardenability by reducing the free energy of sites of ferrite and pearlite nucleation.&apos; The segregation of boron to grain boundaries, the primary site of nucleation, would account for the large hardenability effect of minute additions of boron in steel. This grain boundary theory has found general acceptance while the concept of boron as a nitrogen scavenger has been disregarded. However, the interaction of boron and nitrogen in steel is considered to be important to hardenability because boron may be made ineffective by combination with nitrogen.". * The present work was undertaken to examine some of the effects of boron and nitrogen arid their interaction in steel. A base composition of moderate hardenability was chosen. This was a 0.35 pct C steel containing 2.50 pct Ni and 0.30 Mo. This composition was used because it contained no strong carbide, nitride, or Table I. Composition of Steels by Analysis, Wt Pct Steel C Ni Mo 0&apos; B N* Base 0.35 2.50 0.30 0.0012 nil <0.0001 Boron 0.35 2.50 0.32 0.0012 0.0022 <0.0001 Nitrogen 0.33 2.60 0.35 0.0015 nll 0.0052 Boron plus nitrogen 0.35 2.48 0.30 0.0006 0.0020 0.0040 * Obtained by vacuum fusion technique. boride-forming elements. The other alloys examined were modifications of the base composition and contained nitrogen, boron, or nitrogen plus boron. The compositions of the four alloys used are listed in Table I. The alloys were vacuum melted from electrolytic iron, electrolytic nickel, ferromolybdenum, and fer-roboron. When required, nitrogen was added by admitting a partial pressure of nitrogen over the melt after vacuum melting. The alloys were cast into 21h-in. diam ingots and hot rolled to %-in. sq bars. No ingot pattern was discernible on the polished and etched cross sections of the hot-rolled bars. The alloys were normalized at 1650°F, then machined into standard %-in. diam end-quench hardenability test bars. Four different austenitizing treatments were used: 60 rnin at 1550°F, 45 rnin at 1800°F, 30 rnin at 2000°F, and 20 rnin at 2000°F followed immediately by 30 rnin at 1550°F. The 1550" and 2000°F treatments were carried out in duplicate for each of the four steels. In order to prevent surface oxidation the bars were austenitized while buried under charcoal in an atmosphere of argon. After quenching the bars in a conventional end-quench fixture, the hardness surveys were made in the usual fashion on parallel flats ground along opposite sides of each bar. These were ground 0.050 in. deep rather than the conventional 0.015 in., to avoid decarburized or deboronized regions.5 The austenite grain sizes which resulted from each heat treatment were observed metallographically using Vilella&apos;s etch for martensite. The criterion used as a measure of hardenability was the distance from the quenched ends of the bars at which a hardness of RC 35 was observed. This hardness represented the inflection point on the hardness vs distance plot. Fig. 1 shows the hardenability of each steel after the several heat treatments. The duplicate tests demonstrated excellent reproducibility; the distance to Rc 35 was reproduced within 1/16 in. for duplicate test bars. All four alloys had the same grain-coarsening characteristics. Neither boron nor nitrogen had any observable effect on grain size. The grain sizes resulting from the various austenitizing treatments were ASTM 7 at 1550°F, ASTM 4 at 1800°F, and ASTM 2 at 2000°F. The small amount of boron in the boron steel greatly enhanced hardenability when the samples were austenitized at 1550°F. The low hardenability of the boron plus nitrogen steel showed that nitrogen eliminated the boron contribution to hardenability. Both steels containing nitrogen, with and without boron, exhibited lower hardenability than the base composition when quenched from 1550°F.

Jan 1, 1958

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5&apos;798&apos;14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970

By M. R. Tek

General equations relating the pressure drop necessary to sustain the flow of a fluid through a porous matrix at a given rate have been developed. The results indicate that at high values of flow rate the pressure-flow behavior may not necessarily satisfy the usual Darcy equation. The mathematical analysis, carried through the micro-pore geometry and extended through the macro-reservoir scale, indicate that Darcy&apos;s law, of limited applicability to certain ranges of Reynolds numbers, can be generalized through the inclusion of some additional parameters. The "generalized Darcy equation" has also been formulated in dimen-sionless form permitting the evaluation of its predictive accuracy with regard to literature data. A comparison between predicted and experimental values indicates that the generalized Darcy equation predicts the pressure drops with good agreement over all possible ranges of Reynolds numbers. INTRODUCTION The limits and the nature of validity of Darcy&apos;s law&apos; has been a subject of every-day interest to the industry for many years. It is well known that as the Reynolds number, characteristic of the fluid flow through porous media, becomes large, Darcy&apos;s law gradually loses its predictive accuracy and ultimately becomes completely void. For the last 20 years much has been said and written on this subject. Unfortunately little has been accomplished to bring about a satisfactory agreement, at least on the nature of the threshold of validity of Darcy.&apos;s law. Fluid dynamists, geo-physicists, and engineers all had their individual views, explanations, interpretations and concepts on the subject. To some, a mechanistic analogy with pipe-flow proved a satisfactory explanation.&apos; To others,&apos; turbulence, in its random character, was incompatible with the geometric structure of consolidated porous systems. To some,4 turbulence merely represented a factor influencing the permeability measurements and again to others5,6,7 em-pirical or semi-empirical correlations proved satisfactory from an engineering viewpoint. Deviations from Darcy&apos;s law at high flow rates have been studied by systematic experiments by Fancher, Lewis, and Barnes.&apos; In an article on the flow of gases through porous metals, Green and Duwezs conclude that the onset of turbulence within the pores appears unsatisfactory to explain deviations from Darcy&apos;s law. This view is held by many others. While the subject remained controversial for many years, the development of vast natural gas reserves throughout recent years further justified considerable interest on this problem from the standpoint of gas reservoir behavior. As large amounts of field data became available from the operation of many gas fields, it became evident that the steady-state behavior of gas wells was not, in general, in agreement or compatible with Darcy&apos;s law. This suggested a careful reconsideration of all mechanisms which may account for pressure drops in addition to viscous shear. In a series of articles9,10 . Hou-peurt indicated that deviations from Darcy&apos;s law may be explained on the basis of kinetic energy variations and jetting effects without resorting to assumptions on turbulent flow conditions. Another article by Schneebeli11 indicates that special experiments by Lindquist clearly demonstrated that the onset of turbulence does not necessarily coincide with conditions of deviation from Darcy&apos;s law. This view is also held by M. King Hubbert.12 Starting with the basic pressure-flow relations suggested by Houpeurt, the derivation, development and extension of analytical expressions to -supplement and generalize Darcy&apos;s law has been the objective of this work. MATHEMATICAL ANALYSIS Derivation of Dimensionless Pressure-drop, Flow-rate Relations In considering the flow of a fluid through a porous matrix geometrically represented by a succession of capillary passages in the shape of truncated cones,810 an approximate expression may be derived relating viscous and inertial, i.e., total pressure drop to the physical properties of the fluid, geometric properties of the rock matrix and the rate of flow: ?P/?r = µ/k V [ 1 + c(m4 - 1) p V/16n" mµ w] ..........(1) Let us formally set: c (m4 - 1) / 16n" m = a d ......(2) Such a representation is equivalent to assert that the term [c(m4 — 1)/ 16n"m], variable with various porous media and probably highly variable within a given porous medium, may be macroscopically defined as equal to a lithology factor times the aver-age grain diameter d. In view of the usual grain and pore size distribu-

Jan 1, 1958

By H. Sigurdson, T. V. Cherian, C. H. Moore

The phenomenon of recovery of cold-worked metals is interesting not only because of its practical importance but also because of its fundamental significance in solid state reactions. Although extensive investigations1,2 have already been made in an attempt to discover the mechanics of the recovery process, many of the observations have not yet been satisfactorily correlated to provide a completely consistent model for the process. The wide differences in the recovery rates of various properties can be cited as a typical example of one of the difficulties that are encountered. Frequently, for example, the electrical resistance will have almost completely recovered before any recovery in tensile strength can be detected. Of course, such differences in the recovery rates of different properties might be explained by assuming that each property is a unique function of the work-hardened state, and consequently each property exhibits its own unique recovery rate. The assumption that different properties are uniquely related to the work-hardened state cannot be denied. On the other hand, the properties that recover at different rates often exhibit more or less parallel changes upon work-hardening. This suggests that the microstructural changes attending recovery are not exactly the reverse of the changes attending work-hardening. Several types of imperfections must be postulated in order to account for this apparent anomaly. The different recovery rates for various properties, then, are due to the different recovery rales of the type of imperfection to which each property is most sensitive as well as the unique dependence of each property on the cold- worked state. This concept assumes that a simple model of the work-hardened state consisting only of one type of imperfection, such as Taylor&apos;s type of dislocation patterns, is inadequate to cope with the diversified phenomena attending work-hardening and recovery. Although current models for the work-hardened state are not useful for describing all aspects of the recovery process, the general trends of the recovery of each postulated type of imperfection as a function of time and temperature should be at least qualitatively deducible from the rather well developed laws of kinetics of reactions in the solid state. Consequently, recovery data might prove useful for elucidating some aspects of the complexities of the work-hardened state of metals. A preliminary attempt to study work-hardening by investigating recovery rates of cold-worked metals is outlined in the following pages of this report. Experimental Procedure Many properties recover when cold-worked metals are annealed below their recrystallization temperature. Therefore, electrical resistivity, thermal electromotive force, X ray diffraction line widths, X ray diffraction line intensities, elastic spring back, density and other physical and chemical properties have been used to study the recovery process. Major interest, however, has generally been directed toward the recovery of the mechanical properties such as hardness, yield strength, and tensile strength. But a search of the literature suggests that the effect of recovery on the true stress-true strain curve has been neglected, in spite of the current recognition of the fundamental importance of such an investigation. An investigation on the effect of recovery treatment on the true stress-true strain curves in tension, therefore, was undertaken in the present study. Commercially pure aluminum (99. + pet Al) in the form of 0.100 in. thick rolled sheet of 2S-O aluminum alloy was selected as the material for this investigation because rather extensive correlatable data are already available on the recovery of some of its properties. Tensile specimens having a 6 in. long gauge section and a uniform reduced section width of 0.500 in. were machined from the sheet in accordance with a design that has previously been reported.3 All specimens were selected with their axes aligned in the rolling direction. In order to eliminate the effects of previous work-hardening and the effects of machining, the specimens were annealed for 15 min. at 750°F before testing. During tensile testing the loads were measured by means of a proving ring (sensitive to 1/2 lb) in series with the specimen.4 Strains were determined from the extension of a rack and pinion strain gauge sensitive to a strain of + 0.0001. The stress was recorded as the true stress, namely

Jan 1, 1950

By L. W. McKeehan, W. C. Elmore

The magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined1, "or investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators:&apos; have used Bitter&apos;s original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement ill the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. Specimens The following list describes the specimens used in the present investigation. Designation Description A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which lie gave the following typical analysis: C, 0.05; P, 0.038; S, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick. By X-ray analysis angles between disk normal and [100] 75o, [0101 76" [00l] 21o. A2 Same as A1 except: diameter 0.75 cm. A, Same as A1 except: diameter 0.68 cm.

Jan 1, 1936

By F. I. Grace, L. E. Murr

The mechanical responses and residual defect structures in 70/30 brass and type 304 stainless steel following explosive shock loading and cold reduction by rolling have been studied. A distinct relationship was observed to exist between the residual mechanical properties and micro structures observed by transmission electron microscopy. Shock-loaded brass deformed primarily by the formation of coplanar arrays of dislocations and stacking faults at lower pressures, and twin-faults (deformation twins and €-martensite bundles) at higher pressures (> 200 kbar). The micro -structures of cold-rolled brass were characterized by dense dislocation fields elongated in the rolling direction. Stainless steel was observed to deform by the formation of dense arrays of stacking faults at lower shock pressures and twin-faults at high shock pressures (>200 kbar). Lightly cold-rolled stainless steel deformed similar to low Pressure shock-loaded stainless steel, but transformed to a&apos; martensite in heavily cold-rolled stainless steel. Discontinuous yielding was observed for the heavily cold-rolled stainless steel, and stress reluxution in the weyield region for cold-rolled and shock -loaded stainless steel was interpreted as an indication of the ability of twin-faults and stacking faults to act as effective barriers to dislocation motion. A simple model for the formation of the planar defects and a&apos; martetnsite is presented based on the propagating of Shochley partial and half-partial dislocations. A considerable effort has been expended over the past decade in an attempt to elucidate the response of metallic-crystalline solids to the passage of a high velocity shock wave (e.g., smith,&apos; Dieter,2 and zukas3). While it has been possible to obtain relevant information pertaining to the residual defect structures and mechanical properties, there have been few rigorous attempts to draw a direct comparison between these structures and properties. In addition, numerous investigators have recently observed the occurrence of deformation twinning in shock deformed fcc metals (e.g., Nolder and Thomas,4 and Johari and Thomas5), but little attempt has been made to elucidate the mechanisms of formation of these defects. Comparative data for metals deformed by shock-loading and the same metals deformed by more conventional modes of deformation such as cold-reduction by rolling is also generally lacking. The present investigation therefore has the following objectives: 1) to examine the mechanical properties of some explosively shock loaded and cold-rolled fcc metals of low stacking-fault energy as a function of their residual substructures; 2) to present a simple model for the formation twin-faults and related defect structures in the low stack-ing-fault energy materials of interest (70/30 brass, ySFg= 14 ergs per sq cm; and 304 stainless steel, ySF = 21 ergs per sq cm); 3) to make some deductions with regard to the residual characteristics of dislocation and planar defect substructures in cold rolled and shock loaded 70/30 brass and type 304 stainless steel. In particular, it was desirable to characterize the residual hardening effects of particular deformation substructures. I) EXPERIMENTAL PROCEDURE Sheet samples of 70/30 brass (0.005 and 0.15 in. thick; annealed at 659°C for 2 hr) and type 304 stainless steel (0.007 in. thick; annealed 0.25 hr at 1060°C) of nominal compositions shown in Table I were cold-rolled in one direction only to produce reductions in thickness of 15, 30, 45, 60, and 75 pct in the brass; and 5, 15, 25, 35, and 45 pct in the stainless steel. Identical sheet samples in the annealed (unrolled) state were subjected to plane compressive shock waves to various peak pressures ranging from 0 to 400 kbar in the brass and 0 to 425 kbar in the stainless steel; and with a constant peak pressure duration of approximately 2 microseconds. A detailed description of the shock loading technique has been given previously.6 Tensile specimens 1.0 in. in length and 0.125 in. in width were cut from the cold-rolled sheets (tensile axis parallel to the rolling direction), and the shock-loaded sheet specimens. Stress (load)-strain (elongation) measurements on the tensile specimens were made on a Tinius-Olsen load-compensating tensile tester using a strain rate of 2.7 x 10-3 sec-1. Tensile tests were repeated at least twice, giving essentially the same results. Stress relaxation measurements in the preyield region were also made using an initial strain rate of 5.4 x 10-4 sec-1. In addition to tensile and stress relaxation measurements, Vickers microhardness measurements were made on all samples. A total of 100 microhard-ness readings were obtained for each specimen following a light electropolish to ensure uniform surface conditions for all tests. The hardness averages ob-

Jan 1, 1970