Search Documents

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By B. H. Kear

All the possible ways of forming simple two-dislocation boundaries in multiple slip orientations are deduced. It is shown that the principal differences in work hardening behavior of crystals plastically deformed in these orientations can he accounted for in terms of the likelihood of formation of diffuse boundaries, or deformation bands, consisting of the products of dislocation reactions of the Lomer type. Also, it is pointed out that the break-up of boundaries under the applied stress is more likely to yield interstitial jogs than vacancy jogs, whereas glide dislocations cutting throuqh dislocations trapped in particularly stable boundam'es can acquire both types of jogs. USING Frank's' grain boundary formula, Ball and Hirsch2 determined the parameters of all the possible boundaries that can be built from two sets of glide dislocations in the fee structure. This paper deduces the geometrical possibilities for the formation of these two-dislocation boundaries in the different multiple slip orientations, and discusses the role of boundaries in work hardening and in jog formation. Formation of Two-Dislocation Boundaries in Mutiple Slip Orientations. The parameters of the possible two-dislocation boundaries for any crystal orientation can be deduced most conveniently using the boundary formulae due to Amelinckx,3 in conjunction with the stereographic projection shown in Fig. 1. Suppose that slip occurs in a-BC and ß-CA. According to Amelinckx, when the two systems of glide dislocations are parallel, the rotation axis, u, of the boundary is parallel to (a x ß) and the unit normal, u, defining the boundary plane is parallel to (a x ß) x (BC x CA). On the other hand, when the glide dislocations form a crossed grid, u is parallel to (BC x CA) and u is parallel to (a x CA) x (ß x BC). In Fig. 1, (a x ß) is the pole of the great circle passing through a and ß, so that u is parallel to DC, i.e., parallel to [110]. Furthermore, (a x ß) x (BC x CA) is the pole of the great circle passing through DC and 6, so that u is parallel to [110]. Hence, when all the glide dislocations are parallel, the boundary is pure tilt with parameters u = [110], v = [ 110]. Similarly, it may be shown that the corresponding crossed grid of dislocations is a mixed boundary with u = [111], u = [111]. Consider the case of a crystal compressed in the [001] orientation. In this orientation, according to Fig. 1, there are eight available slip systems. In what follows, the different types of two-dislocation boundaries that are possible in this orientation will be examined by taking different combinations of two slip systems out of the available eight, with a-BC always one of the systems. Case (i)—Slip Systems a-BC and d-CB. The formation of a tilt boundary in (101), which consists of a crossed grid of edge dislocations with vectors BC andCB, is illustrated in Fig. 2(a). As the figure shows, slip is required in the system a-BC in one part of the crystal and in d-CB in the other part, with both sets of dislocations entering the boundary from opposite sides. The rotation axis of the boundary lies in (101), depending on the relative densities of the two sets of edge dislocations in the boundary. Case (ii)-Slip Systems a-BC and ß-CA. The two possible boundaries are shown in Figs. 2(b) and (c); boundary (b) is tilt with u = [110], u = [110], and

Jan 1, 1962

By Meguru Nagamori

DURING the smelting of the sulfide ores of copper, nickel, and certain other metals, a matte phase is formed. For a better understanding of the physico-chemical properties of mattes, binary systems such as Cu-S, Ni-S, Fe-S, and so forth, should be studied, especially in the vicinity of liquid compounds such as Cu2S, Ni3S2, FeS, and so forth. These compounds are relatively stable in the solid state although they can exhibit appreciable deviations from stoichiometry. With small deviations from stoichiometry there are large changes in the activity of both sulfur and metal this is a characteristic of both solid and liquid sul-fides near the stoichiometric compositions. In the vicinityof molten Cu2S,1 for instance, the activity of sulfur increases about 100 times for a 0.012 increase in the mole fraction of sulfur and, correspondingly, the activity of copper decreases greatly. In this sens the minor deviations from stoichiometry should be carefully taken into account in studies of such metal-sulfur melts. Metal-sulfur melts may be considered to have properties intermediate between metallic solutions and molten salts, i.e., neither entirely metallic nor entirely ionic. The radius of the ion sZ- is 1.84 as compared with 1.04? for a single bond covalent s.2 It is therefore inferred that when the sulfur is more ionic its partial molar volume is larger, although metal-metal, metal-sulfur, and sulfur-sulfur interactions may bring about further complexities. Thus, it is to be expected that the molar volumes, which are derived from density-composition relations, will help in resolving the structure of the melts. In this study the maximum bubble pressure method with bubbling gases of H2, H2S, and Ar, .was employed to measure the density. EXPERIMENTAL Materials. Silver of 99.95 pct purity was melted in an alumina crucible and hydrogen gas was then bubbled through the liquid for the deoxidation. In preparation of Cu2S, electrolytic copper powder (>99.9 pct Cu) was mixed with precipitated sulfur and heated to 1200°C in an alumina crucible under a hydrogen atmosphere. Mixtures having the approximate compositions FeS and Ni3S2 were prepared by heating reagent grade electrolytic iron or reduced nickel powder with precipitated sulfur under a hydrogen atmosphere. The H2S gas was of 98.5 pct purity, the impurities being mostly CO2 and CS2 which hardly contaminate the melts. Apparatus. The crucible system is shown schematically in Fig. 1. To minimize the variation of melt composition during a density measurement, the apparatus was designed in such a way that either Ar, H2, H2S, or mixtures of these gases could be used as the bubbling gas. When the melt had a high partial pressure of sulfur, H2S gas was used. When the partial pressure of sulfur was so low that oxygen might dissolve in the melt, the use of H2 was preferred. In intermediate cases, argon or mixtures of H2-H2S were used. Density of Dibutylphtalate. Dibutylphtalate was used as the manometer fluid. Relative to distilled water, the density of the dibutylphtalate, pdib g per cc, was measured and found to be: pdib (25°C) = 1.046 i 0.002. With the use of the temperature coefficient reported by Kemppinen and Gokcen,3 the following value was

Jan 1, 1970

By C. S. Barrett

The torsional after-effect in polycrystalline cadmium is interrupted by an abnormal twisting when the film is removed by etching. This is accounted for by the pile-up of dislocations beneath anodic or other oxide films during the original twisting, and the relief of the residual stresses from these by elastic and plastic processes during etching. WHEN an iron or zinc wire coated with oxide is plastically twisted and then released, it untwists according to a law of equal increments in equal intervals of log time, but if the oxide is suddenly removed by etching this normal after-effect is interrupted by a transient, and thereafter the untwisting is slower.' Etching may even reverse the strain temporarily. Related effects caused by hydrated oxide films on cadmium in creep tests have been observed by Phillips and Thompson:' definite transient strains caused by the removal of the film from single crystals of cadmium were observed; however, negligible effects were obtained with polycrystalline wires. Pronounced effects of both transient and steady nature were observed by Phillips and Thompson when anodic films 10-4 cm thick were etched off, and weak effects, transient only, occurred with hydrated oxide films 3x10 cm thick such as were formed by standing in water for 10 min. It was estimated that 10.' cm films, formed in water in 1 or 2 min, could be detected in the apparatus of Phillips and Thompson. Since abnormal after-effects were observed by the torsion method equally well with polycrystalline and monocrystalline iron and zinc wires,' it was anticipated that the torsion method would also disclose them in polycrystalline cadmium, in spite of the fact that analogous effects had not been observed in tensile creep tests on polycrystalline zinc by Pickus and Parker3 r on polycrystalline cadmium in tensile studies by Andrade and Randall." Because of its high sensitivity, particularly its sensitivity to surface conditions, the torsion method was thought to merit further study as a method of investigating thin films of various types and the action of various reagents on these films. Materials and Methods Cadmium wires were cold-drawn to a diameter of 0.039 in. from a stock that was determined spectro-scopically to contain 0.05 pct Bi, 0.005 pct Cu, 0.008 pct Pb, and 0.007 pct Si. The wires were cut to about 17/8 in. lengths and were annealed 1 hr in air at 290°C, after which the grain size was such that there were 5 to 7 grains across a diameter. The wires were then mounted as indicated in the insert in Fig. 1, one end being fastened with laboratory wax into a small diameter brass tube and the other end being waxed to a thin glass fiber which supported, on its upper end, a small galvanometer mirror. The wires were waxed with care to avoid straining or annealing, for it was found that the after-effect rate was sensitive to prior cold work in a wire. The assembly was then clamped above a beaker into which the reagent could be poured. The lower end of the wire was held in the hand while the wire was twisted 180"; it was then released immediately. Since precision timing of these manipulations was not attempted, the different wires cannot be compared as to exact rates of untwisting. The length subjected to plastic strain was 15/8 in. The surface coatings studied were those produced by the annealing in air, by anodic treatment of

Jan 1, 1954

By E. H. Edwards, J. Washburn, E. R. Parker

The mechanism of strain hardening was discussed in connection with some recent observations on the stress-induced motion of dislocation boundaries and on the simple shear deformation of zinc, cadmium, and copper crystals. THE nature of work hardening accompanying plastic deformation of metals has long been the subject of speculation. As early as 1925, Becker' suggested a thermodynamic process to explain slip based on the statistical probability for the occurrence of local glide steps. The theory that plastic glide was due to the presence of lattice defects known as dislocations was first introduced in 1934 by Taylor: and Orowan, and Polanyi.4 Taylor presented a rather complete analysis of the behavior and interaction of dislocations. He assumed a certain type of stress field to be associated with a single dislocation, and postulated that work hardening would result from plastic flow in two ways. First, dislocations following one another across a slip plane might encounter a barrier which would impede their movement, thereby gradually diminishing and eventually stopping plastic flow on that plane. The second mechanism involved the concept of dislocations traveling in opposite directions on nearby planes attracting one another to form a meta-stable lattice. The interaction of dislocations in such an array was shown to be large enough to require an increase in stress before plastic flow would continue. Kochendorfer5,6 extended the concept of work hardening involving a back stress due to an accumulation of like dislocations on a slip plane. He suggested that the formation of a new dislocation is hindered by those dislocations already present. The hardening resulting from the interaction of newly forming dislocations with bound dislocations was designated as "formative hardening," and indicated to be the only type of hardening necessarily connected with the slip process. In another detailed picture of work hardening, Mott and Nabarro7 assumed that sufficient dislocations are primarily present in the crystal as a consequence of growth irregularities (mosaic structure) to initiate slip. Work hardening resulted from the interaction of migrating dislocations with localized internal stresses produced during deformation. More recently, however, Mott8 as modified his treatment to include the generation of dislocations at Frank-Read sources and he accounts for the hardening by the formation of sessile dislocations. It has been widely accepted that metals of hexagonal structure, usually possessing only one set of glide planes, exhibit mechanical behavior markedly different from those having cubic structures. However, the differences in behavior of the two classes may be less fundamental than suggested. Rohm and Kochendorfer9 have shown that a single crystal of aluminum subjected to approximately simple shear gives the type of stress-strain curve associated with the hexagonal metals. Similar behavior has been demonstrated for gold and silver crystals by Andrade and Henderson.'" Thus when glide in cubic metals is restricted to one plane, the strain hardening characteristics closely resemble those of the hexagonal metals. It would appear, therefore, that an investigation of some of the strain hardening properties of single crystals sheared in simple glide might provide a more complete understanding of the phenomenon of work hardening. This report relates a number of recent observations made on single crystals of copper, zinc, and cadmium tested in simple shear. In addition, pertinent observations of effects accompanying stress-induced movement of dislocation boundaries are reported. Experimental Procedure and Results Details of the production and advantages of the type of single-crystal shear specimen employed for the following tests have been presented in a previous publication.n The method of testing makes

Jan 1, 1954

By B. F. Buie

For over 200 years meerschaum has been a significant item of trade between the Near East and countries to the west. Best-known for its use in making smoking pipes and cigar and cigarette holders, it is also used in making a variety of decorative and ornamental items. It is easily carved, and is given an attractive, lustrous finish by rubbing. No published specifications are known, but compact form, purity, uniform whiteness or light color, and uniform, porous texture appear to be requisites. Fig. I a shows the appearance of a piece of crude meerschaum from Turkey; Fig. lb a carved item; and Fig. lc, d, and e show the fibrous and porous texture as revealed by the scanning electron microscope. Neither a major industrial mineral nor a precious stone, meerschaum nevertheless holds a record of long-and continuing-association with art and personal affairs of man. It is also a mineral to which modem methods of exploration and production probably could be profitably applied. An interesting account of the preparation and use of meerschaum in the early part of this century is given by Sterrett (1907). Geology and Mining Mineralogy Meerschaum is recognized now to be the compact variety of sepiolite, the claylike variety of which is one of the minerals included in the chapter on clays. The word meerschaum, from the German meaning "sea foam," was in earlier times used synonymously with sepiolite, a word of Greek origin suggestive of the resemblance of the compact variety-then the only variety known-to cuttlefish bone. At one time meerschaum was used as the commercial name, and sepiolite for the scientific name. However, to think of meerschaum as the name by which sepiolite is known commercially is no longer valid, in view of the recent emergence of the earthy variety as a competitor of bentonite and other clay materials. Present tendency is to restrict the term meerschaum to the compact variety, and to use the term sepiolite as a more general name to include both the compact and earthy varieties. This is the terminology followed in this publication. Meerschaum typically is white to light gray, has a hardness of 2 to 2 ½ , conchoidal to irregular fracture, and specific gravity varying with porosity from about 2 to less than 1. The composition is somewhat variable,- but is near that determined by Schaller (1936) for sepiolite as 2MgO.3SiO2.4H2O. A more modern for mula based on X-ray determination of the crystal structure is given by Caillére and Henin (1961) as (Site) (Mg9)030(OH)6(0H2)46H20. The reason for the firm, compact nature of meerschaum, in contrast with the earthy variety of sepiolite, is not fully understood. It may be due to the presence of a very minor amount of some bonding material such as silica. Scanning electron microscope (SEM) photographs of a specimen from Turkey (Figs. lc-le) indicate that the meerschaum is composed predominantly, if not entirely, of crystalline fibers which merge into sheetlike forms in a complex, intertwined mass. Detailed X-ray and crystal structure data, as well as some data on thermal stability range, are given by Caillère and Hénin (1961) for the sepiolite family of minerals. Mode of Occurrence and Origin Most authors have attributed the origin of meerschaum to alteration of serpentine or other magnesian minerals. The occurrence in alluvium and other surficial deposits does not necessarily indicate that the alteration was supergene. In fact, hydrothermal origin appears more likely for some deposits, though not for all.

Jan 1, 1983

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Carters-ville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.' With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2 The barite-producing part of the Cartersville district is relatively small, having from north to south a length of 4.5 miles, and a width of 2 miles. This small area, containing 35 barite mines, is the source of practically all of the barite produced in the state. The area is hilly, and has a total relief of 500 ft. The west-flowing Etowah River crosses the middle of the area, and is an unfailing source of water for operations on properties near its course. Opencut mining is carried on during the entire year, but is hampered by rain in the winter and early spring. Three railroads, two U.S. highways, and a network of graded roads provide access to and within the district, as well as excellent shipping facilities for ore and supplies. In addition to the barite, the district contains deposits of manganese, brown iron, ocher, umber, and specular hematite. Geologic Setting The area containing the barite deposits is underlain by Lower Cambrian rocks and their weathered residua. These rocks are grouped in three formations; in ascending order, these are the Weisner, the Shady, and the Rome. The Weisner formation consists mainly of finely micaceous metashale containing many random beds of quartzite, a few beds of conglomerate and metasiltstone, and beds of crystalline limestone that is apparently scarce. The formation is more than 1000 ft thick, and the base is not exposed. On account of their resistance to weathering, the rocks of the Weisner formation have sustained the higher elevations and therefore crop out on the ridges that characterize the area. Nearly all of these ridges are underlain by asymmetric anticlinal folds, and conversely the intervening valleys are underlain by synclinal folds. A diagrammatic section, showing typical mode of exposure of the Weisner rocks and their relation to overlying formations, in the limb of a fold, is shown in Fig 1. The Shady formation here consists of a lithologically distinctive series of variably siliceous specular hematite beds and thin beds of dolomite, which in places contain abundant fossils. In the zone of weathering, the dolomite has been leached and most of the hematite hydrated to ocherous and umber-ous clays, hut bedding planes in these weathered materials are commonly well preserved with or without distortion effected by slumping. This preservation of structure during weathering is lacking in the residuum that rests on the Rome dolomite, which is described below. The maximum thickness of the

Jan 1, 1950

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By George E. Cole

While many parts of Canada's pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas inaccessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Although summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transportation has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys occupied by lakes and rivers Or by many low-lying portions covered with muskeg' Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer distances but it is not every water route that will satisfy the conditions of loading freight on to a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer Over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc- tion over a long period, it may be necessary to haul large quantities of supplies during the winter. This seasonal problem, particularly for the out-of-the-way properties, is SO important and demanding as to make it a major operation in the life of the mine. The -use of the tractor during winter months for heavy machinery and bulk supplies, and the use of the airplane throughout the year for the transportation of personnel and for emergency requirements, have greatly improved transportation to places that are inaccessible by rail. Canada has pioneered in both these methods. Development oF Transportation Twenty-two years have seen a marked change in transportation methods in Canada's mining country. Horse-drawn sleighs have given way to the tractor and that to some extent has been supplanted by the airplane. One of the earliest ventures involving transportation of considerable magnitude was that of the Mandy mine, on Schist at in northern Manitoba. According to accounts of early mining activities in Manitoba, the Mandy mine, beginning December 1916, had 3300 tons of ore hauled 40 miles by sleigh to Saskatchewan River and in summer this was conveyed by barge to The Pas, 130 miles, and then by railroad to Trail, British Columbia, 1200 miles. The mine shipped 6000 tons of ore in 1918 and 15,000 tons in 1919. In winter of the latter year, as many as 300 teams of horses were used on the 40-mile stretch to

Jan 1, 1943

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By Cyril Stanley Smith

On the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1758, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Caval103,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold- working restored it. He encountered some samples of brass that could not be rendered - magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found _ the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condi- tion, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitter8 in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant: Honda and Shimizu, l0,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1942

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By George E. Cole

While many parts of Canada's pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas inaccessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Although summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transportation has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys occupied by lakes and rivers Or by many low-lying portions covered with muskeg' Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer distances but it is not every water route that will satisfy the conditions of loading freight on to a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer Over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc- tion over a long period, it may be necessary to haul large quantities of supplies during the winter. This seasonal problem, particularly for the out-of-the-way properties, is SO important and demanding as to make it a major operation in the life of the mine. The -use of the tractor during winter months for heavy machinery and bulk supplies, and the use of the airplane throughout the year for the transportation of personnel and for emergency requirements, have greatly improved transportation to places that are inaccessible by rail. Canada has pioneered in both these methods. Development oF Transportation Twenty-two years have seen a marked change in transportation methods in Canada's mining country. Horse-drawn sleighs have given way to the tractor and that to some extent has been supplanted by the airplane. One of the earliest ventures involving transportation of considerable magnitude was that of the Mandy mine, on Schist at in northern Manitoba. According to accounts of early mining activities in Manitoba, the Mandy mine, beginning December 1916, had 3300 tons of ore hauled 40 miles by sleigh to Saskatchewan River and in summer this was conveyed by barge to The Pas, 130 miles, and then by railroad to Trail, British Columbia, 1200 miles. The mine shipped 6000 tons of ore in 1918 and 15,000 tons in 1919. In winter of the latter year, as many as 300 teams of horses were used on the 40-mile stretch to

Jan 1, 1943

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By Ward C. Smith

The industry of producing and processing boron compounds is called the borax industry because the chief product is borax, the decahydrate of disodium tetraborate. For the same reason, it is common to speak of borax mining. Reference to borate mining also is common, and while appropriate where it emphasizes the diversity of borate minerals that are mined in various countries, it is rather unsatisfactory where used in a general sense, because it seems to exclude the important production of borax from brine at Searles Lake, California, and of boric acid from steam vents in Tuscany, Italy. The terms "boron industry" and "boron mining" might seem more comprehensive, but are little used, and this is fortunate because they would be misleading-the element boron is manufactured only in small amounts for special uses, and it is not found free in nature. In most occurrences, boron is combined with oxygen and is in a borate or borosilicate material. The history of the modem borax industry starts with the introduction into Europe of borax from Tibet in the 13th century, about the time of Marco Polo, if not actually by him. The discovery that borax has unique value as a flux in metal soldering and ceramic glazing must have been made at some unknown time much earlier. As a rule, any mineral that has been used so long that its early history is lost must occur in deposits that are easily recognized and worked, and this is undoubtedly true of borax in Tibet. According to meager accounts,9 the borax occurs there in arid mountain basins as surficial crusts that coat the ground about thermal springs and seeps of mineralized water, and as coarser crystals in the bottom muds of shallow pools and lakes. Much the same essential features of surface exposures and minerals easy to recognize and recover characterize most of the deposits later found and worked elsewhere. The borax industry at the present time is faced with rising demands for its products, and consequently is increasing its productive capacity and appraising its borate resources.18 The areas that contain the known borate deposits are most likely to yield additional production, hence their distribution in the world is of interest, and is summarized later in this chapter. Mineralogy The mineral raw materials used by the borax industry include various borates mined in several countries, borax extracted from brines at Searles Lake in California, and boric acid extracted from the steam of vents in Tuscany in Italy. The hydrated borates[$] of chief commercial importance are listed in Table 1, which also shows their chemical composition. The properties of only the four most important borates are summarized here, but detailed descriptions of the borates and the minerals commonly found with them can be found in mineralogy textbooks.41 Ulexite generally forms clusters of silky fibers rather than large individual crystals. A

Jan 1, 1960

By Cyril Stanley Smith

On the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1758, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Caval103,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold- working restored it. He encountered some samples of brass that could not be rendered - magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found _ the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condi- tion, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitter8 in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant: Honda and Shimizu, l0,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1942

By Paul D. Merica, O. B. J. Fraser

PROBABLY the first metallic objects used by man were nickel alloys. In search for flints suitable for the fashioning of their rude tools, our paleolithic ancestors, some 25,000 years ago, quite likely may have come upon some of those heavy, metallic fragments that we now know as meteorites, which consist of an alloy of nickel and iron containing usually from 5 to 15 pct of nickel. Whether paleolithic man ever did discover and use meteoritic fragments, his sketchy records do not actually disclose. We do know, however, that such fragments have been found and used by peoples, particularly the North American Eskimos, for weapons and implements in just the same manner as stones, and prior to any knowledge by those peoples of the reduction of metals from ores. Meteoritic showers were recorded frequently in earliest times and the meteorites often were found and fashioned into useful objects. The ancient Arabic and other myths of "invincible swords fallen from heaven" seem thus to have had a very definite basis in fact, and such weapons, of meteoritic material, have actually been re- covered from archeological excavations. It thus seems probable that meteoric nickel-iron was found and used long before iron was recovered by smelting iron ores (perhaps about 1200 B.C.) and probably even before there was knowledge and use of bronze and gold. Although many centuries were to pass before nickel was first isolated, in 1751, from Swedish ores and recognized as an elemental

Jan 1, 1953

By Stephen Taber

A VEIN may be defined as an aggregation of mineral matter, more or less tabular or lenticular in form, which was deposited from solution and is of later origin than the inclosing rock. This definition differs from the one found in many text-books in that no assumption is made as to the origin of the space occupied by the vein or the manner in which the mineral matter was deposited. In the present paper the writer purposes to discuss the mechanics of vein formation, and does not wish to begin by begging the question. The origin of ore deposits has been diligently investigated in recent years, but, while much has been written concerning the chemistry of the process, the physical side of the question has received less attention. The source of the ore minerals; the chemical composition of ore-hearing solutions; the relative importance of magmatic and meteoric waters as agents of concentration; and the causes of mineral precipitation have all been discussed at length. On the other hand, little has been written concerning the mechanics of vein formation, and the theories given in text-hooks today are essentially the same as those developed by the early Cornish and Saxon miners. Early investigators often regarded both veins and dikes as igneous in origin, but today the theory that vein minerals have been deposited from solutions, either liquid or gaseous, is firmly established. The latter view is supported by the fact that many vein-forming minerals are not found in unaltered igneous rocks; by evidence obtained in the laboratory regarding the solubility of minerals; by the presence of many ore minerals in hot-spring waters; by the occurrence of some veins in regions consisting exclusively of unaltered sedimentary rocks; by evidence as to the temperature at which some minerals are formed; and by the absence of mineral segregation due to difference in specific gravity. There is still, however, much difference of opinion as to whether certain tabular-shaped 'masses should be classed as veins or as dikes. Some of

Jan 8, 1918

By W. Wanjokow, H. O. Hofman

In the metallurgical treatment of most metallic sulphides it is usually necessary to carry on a roasting-operation. In some cases the raw ore will have to be roasted; in others the intermediary product, matte, produced in smelting the ore; again, both ore and matte may have to be subjected to oxidation at elevated temperatures. Most metallic sulphides, when given an oxidizing-roast, pass through the state of sulphate before they are converted into oxides. All metallic sulphates are completely decomposed by heat, with the exception of those of lead and bismuth, but the temperatures at which decompositions take place vary with the metals. Some metallic sulphates are converted directly into oxides, others first form basic salts. Alkali-earth sulphates show a behavior similar to that of metallic sulphates, while alkali sulphates do not part with their sulphur trioxide even at elevated roasting-temperatures. The older data on the decomposition of metallic sulphates by heat are only approximations. Thus Kerl' gives the order in which metallic sulphates are decomposed with increasing temperatures as (Ag2, Fe, Cu, Zn, Ni, Co, Mn, Pb) SO,. More recent statenlents give definite temperatures and modify the formerly accepted order of decomposition. But the temperatures given by various observers do not agree. The reasons for this are to be found mainly in the method and manner of carrying out experiments. Four methods have been used: 1. Heating in an evacuated tube; 2, heating in a tube closed at one end, without air-cur-

Jan 1, 1913

By A. D. Marlin, A. J. Gentile, E. F. Jordan

Metallurgical changes in SAE 52100 ball-bearing components resulting from overload testing are described. Changes in microstructure, hardness, and resiclctal stresses crre discussed zuitlz re.ference to material cleanliness obtained by various steel-melting practices and are compared with work by otlzer investigators. Evidence is presented to show that the initialion and development of microstruc-tural alterations are characterized by two separate reactions: the appeavance of a "dark etchingJ' constituent, and "gray lines" or a light etclzing constituent. The dependency of these tzvo reactions on material cleunliness, running tirne, and contact stresses is discussed and a failure mode related to material cleanliness and microstructural transformation is proposed. THE study of ball- and roller-bearing contact fatigue has been paced by a strong emphasis on bears ing application performance. Particular attention has been paid to conditions that effect the spalling-type failure that is characteristic of rolling contact fatigue in through-hardened components. Some of the conditions investigated are lubrication and atmosphere,1-3 material characteristics and finish,475 and speed and design fa~tors."~ A typical spalling-type failure is shown in Fig. 1. The arrow shows the motion of the ball relative to the inner-ring race surface. The leading edge of the spall is usually sharper than the trailing edge. The race surface near the trailing edge also shows small dents caused by debris from the spall. In this type of testing very little metallurgical investigation is done on failed bearings. Emphasis is placed on test conditions and statistical analyses of endurance data. More basic work has been done relating micro-structural changes to fatigue performance. Dyer" and Wood, Cousland, and sargant9 have used mostly simple materials, such as single crystals and single-phase polycrystalline specimens, under simple alternating strain to identify a systematic process of fatigue damage. drutowski" was concerned primarily with the relationship between steel structure, contact stress, and energy losses in rolling contact. dones11 and Bush, Grube, and Robinson12 utilized changes in microstructure and residual stress in overload-tested rolling contact elements as a means of investigating the fatigue process. Work is being done on an ASME-sponsored contract,13 using both simple and complex materials, but there is still a long way to go before such theories as pore and void growth in simple structures can be applied to the relatively complex bearing steel microstructure. The purpose of this paper is to report on an investigation into the effect of steel cleanliness on the structural alteration and residual stress changes found in overload-tested ball bearings. Using these results and those of previous investigators, we will propose probable failure mechanisms in both overload- and normal load-tested ball bearings.14,15 PROCEDURE Ball bearings? 3208 size, were fabricated from SAE 52100 steel obtained by five different melting practices. The melting practices, chemistry, and inclusion ratings for the five lots of steel are summarized in Tables I and 11. The nonmetallic inclusion ratings were determined by the Jernkontoret method described in ASTM E45-51 Method A. This technique consists of microscopically examining a series of polished samples taken from specified locations in the ingots, billets, or bars. Each sample is surveyed at XlOO magnification and the inclusion types and sizes are compared to standard fields. Because of the nature of these ratings all values in Table I1 are rounded to the nearest half. The elec-

Jan 1, 1965