Search Documents

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

By J. Pohlig

It is with more than ordinary pleasure that I have complied with the request of the President of the Verein Deutscher Eisenh?tten leute, to read before this meeting and in this country a paper on a system of transport by wire ropeways which, during the past twenty years, has advanced with rapid strides in Europe, and more partic ularly in Germany. America, with its immense network of railways and water communications, should offer peculiarly favorable oppor tunities for the introduction of these ropeways as feeders, more par ticularly in the mining districts, where, as in Europe, a hilly or mountainous region frequently opposes serious obstacles to the em ployment of surface railroads. The importance of the aerial ropeway as a factor in the develop ment of mineral resources deserves the consideration of every mining engineer. As a case in point, the rich iron-ore of the sierra de Bedar in southern Spain, would probably remain untouched to this day but for an aerial ropeway, 15.6 km. (9 3/4 miles) long, which con nects the mines with the shore of the Mediterranean near the town of Garrucha, affording cheap carriage to the nearest shipping point. A railway would have cost about $480,000 (£100,000), but such a heavy outlay would have more than absorbed all prospective profits on the sale of ore. As the aërial ropeway could be built for a little more than one-fourth of that amount, or $124,800 (£26,000), its erection furnished the successful solution of a profitable mining enterprise. This line has been in satisfactory operation for over two yearn; its details will be referred to later. But beside their importance as feeders, ropeways are valuable as a means of conveyance between works and distant warehouses, and between separate buildings in the same works. Their rapidly spreading introduction for such purposes indicates how keenly the necessity of effecting economies is felt under the stress of an everaccentuating competitiop.

Jan 1, 1891

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

Flag Day Celebrations Develop Practical Patriotism Among the hundreds of industries which celebrated Flag Day on June 14, were a number of mines, and a report- from the United States Smelting, Refining and Mining Co. tells how the programs were carried out at Mammoth and Chrome. In the first place, Flag Day was not observed by knocking off work, but by short exercises, after which work was resumed with re-doubled energy. In this crisis, that method of showing devotion to the flag and country might be termed "practical patriotism." In other words, it could be expressed as "Hats off to the flag and sleeves up for it." Harry Hunt, first-aid man at the Mammoth mine, reports that the flag raising was marked by the spirit of high enthusiasm, which included every man, woman and child belonging to the camp. "The miners in their working clothes, still wearing their carbide lamps on their caps, with faces covered with dirt, just as they came from the mine, and the ladies and children with their bits of bright color, made a picture worthy of the brush of a master painter. The program rendered was that arranged by the National Bureau of Education." First came a bugle call, "To the Colors," given by Assistant Superintendent C. W. Plumb. Then Foreman Carpenter W. R. (Bill) Young, raised the stars and stripes to the peak, and as the banner unfurled to the breeze, all heads were bared, and the salute was given by the workers, whose toil at home is strengthening our army in France. Then the miners joined in the singing of the "Star Spangled Banner," and repeated the "Pledge of Allegiance," and the "American's Creed." Shift-boss W. J. Phinazee then addressed his fellow workers, telling them how the flag stands for their protection and that of their loved ones, and how it should be loved and respected, not only by the native born, but by all who live here under its protection. Those of alien birth, who have come here because of the greater opportunities offered in America, owe a special honor to the stars and stripes, and the point was made that these men from other lands should not love their old home less, but their adopted country more. The majority of those present were foreigners, and their hearty applause showed that they appreciated the point made by their shift-boss, who, because of his position, was able to address them as man to man.

Jan 10, 1918

By AIME AIME

IN RESPONSE to a request from the president- elect of the Institution of Civil Engineers of Great Britain, Mr. Calvin W. Rice, secretary of the American Society of Mechanical Engineers, prepared a brief history of the joint activities of engineering societies in the United States, from which we have taken the following facts. National Societies Our first joint activities were in collection with the celebration of the eightieth birthday of "Uncle John" Fritz in 1902, and it is of interest to note that two of the members of the original celebration committee, Messrk. . Ambrose Swasey and Jesse Merrick Smith, will be members of the official deputation to England in June. Mr. Rice, also,' was .a member, of the original committee.

Jan 1, 1921

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

By C. S. Matthews, J. L. Mahaffey, W. M. Rutherford

This paper gives results of an experimental study of the sweep efficiency of a miscible displacement in a five-spot. The study was carried out in a parallel-plate glass model in which effects of diffusion were scaled at or near the molecular diffusion level. The experiments show that very early breakthrough (25 to 35 per cent of pore volume (PV) injected) may be expected in miscible floods because of the unfavorable viscosity ratio. However after 1 PV of displacing fluid is injected, the sweep rises to a reasonable value (50 to 60 per cent). Photographs show that small slugs of less than 10 per cent of PV tend to dissipate before breakthrough. A minimum slug size of 15 per cent of PV would appear to be necessary even in a relatively homogeneous formation. Presence of a slug whose viscosity is inter-mediate between that of oil and gas increases the sweep efficiency of the oil-gas system. In a typical system the sweep at breakthrough rose from 26 to 37 per cent of PV for a 25 per cent slug. The increase in sweep brought about by use of a large slug could well pay for the extra deferment cost of the additional slug material. INTRODUCTION Most miscible displacement processes involve the displacement of oil with fluids of much lower viscosity and density. The displacement process at these adverse viscosity and density ratios is dominated by instability phenomena, i.e., viscous fingers and gravity tongues. These phenomena have highly adverse effects on oil recovery. Although a number of laboratory studies have been made to determine the effect of adverse viscosity ratios on five-spot sweep patterns,l,2 the scaling of diffusion effects is uncertain. In the series of scaled model studies reported herein, an attempt was made to scale diffusion. Model studies of miscible displacements in which molecular diffusion predominates are per-mitted by controlling the parallel plate spacing which reduces convective mixing to arbitrarily small levels. To decide how this scaling relates to any particular Geld displacement necessitates an estimation of diffusion effects for the natural rock being considered and conditions under which displacement will be conducted. The approach normally taken is to extrapolate data obtained from stable miscible displacements performed in the laboratory, such as those presented by Brigham et al.3 The validity with which such an extrapolation can be applied to an unstable flow system has yet to be established. If this approach is accepted, a family of oil recovery curves can be generated for a single viscosity ratio based on Brigham's observation that the magnitude of the dispersion coefficient is dependent, among other things, upon specific rock properties. Objective of our test was to define the lower limit of this range by presenting the case where dispersion effects were reduced to the molecular diffusion level in both the transverse and longitudinal directions.

Jan 1, 1967

By AIME

Compiled by Mary Ann Gross, Department of Energy. Bruceton. PA. Supplemental data from Coal Age indicated by (*). Reprinted by permission from CoalAge magazine.

Jan 1, 1981

GENTLEMEN : Herewith are submitted reports for the calendar year 1933 of your Treasurer and the Chairmen of the following standing committees: Finance, Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for additional details of the year's activity. Finances.-Income for 1933 from all sources totaled $121,690 com- pared with $138,331 in 1932. Incidentally, this exceeded the income as estimated in the budget by $7,190; the largest item being a "surplus" of $3,316 over the budget expectancy as to member dues. As compared with 1932 the most important items of shrinkage in income were $9,000 from dues and initiation fees; $5,500 from the magazine, MINING AND METALLURGY; and $2,500 from sales of publications other than the magazine.

Jan 1, 1934

By C. W. Allen, L. C. Moore

The Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming. on the Marquette iron range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleve-land-cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. Geology The north footwall of the Marquette Range synclinorium outcrops near the north line of set. 2, the iron formation dipping to the south at an angle of about 40. The south side of the trough reappears at a distance of 4J5 miles on sec. 26 and the surface geology between shows iron forma- tion or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850 ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 Per cent P, 5.40 per cent Si, 2-87 Per cent A1 and 0.015 per cent S. Exploration A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1946

By Maurice Magee

The Ducktown ore deposits have been known, explored, and mined for 120 years. Eight massive sulfide ore bodies occur in highly folded and metamorphosed graywacke, graywacke conglomerate, mica schist, chloritegarnet schist, and staurolite schist of Precambrian age. The ore deposits are tabular bodies that have been extensively folded, generally conform to the enclosing rocks, but show local complex differences. The ore deposits, ranging in size from 250,000 tons to over 20 million tons, are composed principally of the minerals pyrrhotite, pyrite, chalcopyrite, sphalerite, and magnetite. Gangue minerals are quartz, calcite, actinolite, tremolite, hornblende, garnet, and masses of schistose wall- rock. Three fault systems are present that have influenced ore control and ore body configuration. Hydrothermal effects are evident in wall-rock alteration. Evidence of retrograde metamorphism is extensive in the wall and ore associated rock. Preliminary isotopic age dates have indicated four possible metamorphic events during the Paleozoic Era. Ore genesis is considered to be hydrothermal replacement of receptive beds, predominantly highly calcareous zones, quartzitic zones, and brecciated shear zones. Ore deposition is thought to have occurred during the Devonian Period, with later mobilization and recrystallization of the ore and gangue during Middle and Late Paleozoic times.

Jan 1, 1968

By E. P. Klier, V. Weiss

IN studies of the X-ray diffraction line geometry of iron with chromium radiation using techniques aimed at minimizing the background intensity, Kp and Ka emission satellites* were resolved with three techniques. These satellite lines are present with sufficient intensity to lead potentially to erroneous structure analysis, if not properly interpreted. The techniques used were: 1) film technique with un-filtered radiation and polycrystalline specimen, 2) film technique with unfiltered radiation and single crystal, and 3) counter technique with unfiltered radiation and single crystal. An example of results obtained with technique 1 is given in Fig. 1.

Jan 1, 1958

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

By J. A. Herbst, R. Mackelprang, J. D. Miller

Droplet size distributions were determined by stabilizing in gelatin and measurement of the distributions by means of computerized image analysis Several variables that affect droplet sizes were studied and the resulting size distributions were modeled via a population balance equation Key parameters in the model were related to the physical properties and operating conditions of the systems examined using a multiple linear approach

Jan 1, 1981

By Thys B. Johnson

Traditional mine planning concepts are discussed and suggestions for improvement through use of the developed model are proposed. The approach developed in this paper allows optimal planning of the complete mining-concentrating-refining system over the entire planning horizon and permits the system to dictate how and when to process a block of material, i. e., a dynamic cutoff.

Jan 1, 1969

By R. H. Harrington

The definition of precipitation-hardening1 is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening1.—This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.—Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheating to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (I) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats. Pkecipitation-hardening of Copper-cobalt-beryllium Alloys1.2 The composition of principal interest is that of 2.6 per cent Co, 0.4 per cent Be, 97 per cent Cu. The alloy has been developed commercially and, with certain reasonable precautions, ordinary brass-foundry practice suffices to produce an alloy of high quality. Preliminary Precipitation-hardening Study.—Samples were cut from a I-in. round rod cast in a graphite mold. These samples were then

Jan 1, 1937

By J. D. McBeth, G. M. Potter, Ramon Pizarro

Heap leaching is used by the Carlin Gold Mining Co., Carlin, Nev., to supplement conventional processing of gold ore by agitation-leaching and countercurrent decantation. Selected open-pit ore containing about 0.072 oz Au per ton is crushed to 3/4 inch, dumped by truck on an asphalt pad, and leached by sprinkling with dilute cyanide solution for 7 days. The heap is then drained and removed by front-end loader to tailings disposal. About 70 percent of the gold is dissolved. Leach solution from the heap joins the pregnant solution from countercurrent decantation for gold recovery by zinc precipitation. Four leach pads, each with a capacity of 1,400 tons of ore, are in use. About 10,000 tons of ore are heap leached monthly from about April through October. Heap leaching is recessed during freezing weather. Labor, equipment, and reagent requirements for heap leaching are presented.

Jan 1, 1974

By Ralph Arnold

LESS than eight months ago at the annual meeting of the American Institute of Mining and Metallurgical Engineers, attention was called to the demoralizing effect of the abnormal oil production of Mexico on the oil situation in the United States, and it was predicted that this unstabilizing influence would probably become impotent in 18 to 24 months through ' the exhaustion of the principal producing fields of Mexico, unless new fields were found in- the meantime. When this statement was made, the daily production of Mexico was about 600,000 bbl. of crude oil; now it is about 350,000 bbl. No new pools of consequence have been opened, although extensions have been made to two old pools. Over 200,000 bbl., or more than half of the present daily production, comes from Los Naranjos, Amatlan and North Zacamixtle fields, in which practically every well is so affected by salt water that the potential production dropped 50 per cent. in the month of September, clearly indicating that these fields are moving rapidly toward extinction. How much longer the one remaining important pool will last is a matter of conjecture.

Jan 1, 1921

By C. W. Davis, L. R. Messer

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.' The properties that make fuller's earth useful in the treatment of petroleum products by "percolation1' and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929