Search Documents

By G. A. Vissac

The only fine coal washer with proved automatic controls, the feldspar jig is capable of good efficiencies even at low separating gravities, handles a variety of products, and treats 150 tph and over. IN continental Europe the feldspar jig is used almost exclusively for cleaning the fine sizes of coal; it operates with an artificial bed, made up generally of pieces of feldspar or of any other hard and heavy rock with good cleavages. A primitive form of this machine requiring close supervision was used in this country years ago, but output was small. The modern machines are generally air-pulsated Baum-type jigs, with capacities up to 150 tph, and treat sizes from % in. to 0, usually previously dedusted or deslimed. These jigs are equipped with very accurate and sensitive automatic controls insuring satisfactory operation even at low separating gravity and with feeds irregular in quality and quantity. This paper will deal more particularly with coal cleaning separation, but the technical studies apply equally to all minerals. Theory of the Feldspar Jig To understand fully the operation of the feldspar jig and to appreciate its potential value, it is necessary to measure and analyze the motion of small particles of various specific gravities, falling in various media, under various conditions. As no practical formulas were available for that purpose, the writer has developed new theories and established new sets of formulas, which cannot be demonstrated here. They are applicable to all minerals and to many problems of coal or mineral concentration. These formulas do not pretend to absolute accuracy, but results, tested by comparison with experimentally recorded data, are sufficient for practical purposes, as they give definite indications of trends, relative values, and order of magnitude of the many factors involved. For pulsating motions no earlier formulas are available. In the case of continuous currents or motions, such formulas as Rittinger's, Allen's, or Stokes', over a hundred years old, apply only to special shapes and sizes of particles, involve factors and coefficients difficult to measure or appreciate, and deal only with free motions. They are of little use in solving practical problems. Units used with the formulas presented here are in the CGS system. Lateral friction and suction have been taken into account according- to methods currently used in aerodynamics, and only hindered motion is dealt with. As the feldspar jig is primarily intended to create a fluid bed condition, the mixture of fluids and solids obtained is homogeneous, and the apparent specific gravity of the separating medium is calculated accordingly. For instance, if 20 pct of the volume is coal and shale, with an average of 1.60 sp gr, in a liquid of 1.10 sp gr, the actual specific gravity of the separating fluid is 0.80 x 1.1 + 0.20 X 1.6 = 1.20. The fundamental equations are as follows: The general motion of a particle falling in a medium of specific gravity equal to u, hindered motion. is dv/dt = g/Ls [ L (s-u) - u/g v2 [1] g = 981 cm per sec, acceleration of gravity, and L = thickness of the particle of specific gravity (s) and velocity (v). The initial acceleration dv/dt = g (1-u/s ) [2] is a function of the specific gravity of the particle, only for a given medium, and independent of its dimensions—an ideal separating condition. The terminal velocity Vt = gxL- (s-u)/u, [3] for a given value of u, is a function of s and L. Two particles, L, s, and L2 s2, are said to be equivalent if they have the same terminal velocity, and accordingly L1/L2=s2-u/s1-u. [4] Two such particles cannot be separated by continuous currents, in any concentrating device. Because the initial accelerated motion, which provides for efficient separation, is followed by a constant velocity, which has a limiting effect, it is essen-

Jan 1, 1956

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946

By J. M. Callow

THe results obtained by pneumatic flotation throughout the country on all classes of ore, and the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practicc. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cyeloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by Dr. Rudolf Gahl on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. CoMPABATIVE SENSITIVENESS AND ATTENDANCE Concerning the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that, with the exception of about 24 days at the end of the testing period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the concIusions drawn on page 499 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 1, 1917

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By H. S. Price, J. E. Warren

Techniques for studying the performance characteristics of heterogeneous reservoirs have been developed. The effect of permeability variation on both the steady-state and the transient flow of a single fluid has been investigated. Limited comparisons with field and laboratory data have been made. The physical models studied consist of random three-dimensional arrays of homogeneous porous blocks. The permeabilities of the individual elements are assigned according to a specific distribution function; uniform anisotropy is introduced by varying the relative dimensions of the blocks. A particular model is perturbed simply by re-arranging its elements at random. The behavior of a physical model is determined by digitally solving its numerical analogue. Based on computational experiments, subject to the restrictions implied by the assumptions that were made, the following general conclusions have been drawn. 1. The most probable behavior of a heterogeneous system approaches that of a homogeneous system with a permeability equal to the geometric mean of the individual permeabilities. 2. The effects of flow geometry and anisotropy on the most probable value of the effective permeability of a heterogeneous medium are finite but not significant. 3. The permeability determined from a pressure build-up curve lor a heterogeneous reservoir gives a reasonable value for the effective permeability of the drainage area. 4. A qualitative measure of the degree of heterogeneity and its spatial configuration are obtained from a comparative study of core analysis and pressure build-up data. It has been indicated that these conclusions are predicated on the assumption that the core analysis and the pressure build-up data represent true reservoir characteristics. Common sources of error in these data have been discussed. One of the most significant problems of reservoir engineering is that of determining the nature and the disposition of the heterogeneities that inevitably occur in petroliferous formations. It is with this problem that this paper is concerned. Extensive research, both theoretical and experimental, has provided reasonable descriptions of the physical processes that are associated with primary and secondaryrecovery mechanisms. Similar progress in the fie1d of numerical analysis and the evolution of truly high-speed digital computers have made it feasible to calculate the behavior of these mechanisms under almost any environmental conditions. It appears to be logical, then, to conclude that the mechanistic performance of any reservoir can be predicted with some confidence. Unfortunate1y, a necessary condition for the validity of this conclusion is that the formation be adequately described in a macroscopic sense. This condition cannot be satisfied ill general; therefore, a frustrating situation currently exists — it is possible to compute the effect of reservoir heterogeneity on behavior, but it is not possible to specify the heterogeneity itself. In many cases, the predicted behavior of a project is so completely dominated by irregularities in the formation's physical properties that the gratuitous assumptior, of a particular form for the variation can reduce the solution of the problem to a mere tautological exercise. While all porous media are microscopically heterogeneous, only macroscopic fluctuations need be considered since the fundamental concepts of reservoir mechanics are based on macroscopic quantities. For the simplest case in which only one physical property varies from point to point, the degree of heterogeneity that is apparent depends on three distinct factors, i.e., the nature of the property's variation (frequency distribution), its disposition (spatial distribution) and the inherent stability of the mechanism being studied. Consequently, any attempt to devise an unambiguous scale of heterogeneity must take these factors into account. Since this investigation is intended to be exploratory, it will be restricted to single-phase flow because of the simplification implied; both steady-state and unsteady-state behavior will be considered. Furthermore, to keep the number of parameters

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By D. W. Philips

The problem of strata control has of necessity been prominent in mining, and accounts of individual experience and research abound in the literature of most mining countries. Organized rescarch began in Britain by the formation of a committee, upon the recommendation of the Safety in Mines Research Board in 1923, to investigate methods of reducing accidents from falls of roof in coal mines. This committee examined current practice in supporting underground workings in the principal coal fields, and its findings have been published in the Board's publications.' - Toward the end of these investigations it was suggested by the Chief Inspector of Mines that committees of the several mining institutes be formed to examine the problem in their respective districts. The formation of these committees marked a new phase in research on strata control. The work, though being done in the separate coal fields, followed a scheme outlined by the chief Mining Engineer of the Research Board, and was coordinated by his office. FACTORS INVOLVED The subject is being considered in Britain from two aspects: 1. To provide. by supports, means to prevent falls of fractured ground. 2. TO develop methods whereby the strata can be maintained in the least broken condition and thus make falls less likely. The first aspect is the one that will most likely lead to immediate results from the accident standpoint. It depends largely upon the assimilation of already acquired knowledge regarding the properties of supports and their correct application. The second aspect is perhaps more fundamental, and involves also the properties of the strata and their behavior under the influence of the forces induced by mining. The problem involves many natural factors that cannot be controlled, such as depth, inclination and thickness of seam and nature of the rocks. Other factors, which may be considered to a certain extent controllable, cannot be varied readily and with sufficient frequency to facilitate easy investigation; some of these are: rate of advance of the working face, length of face, direction of the face with regard to cleat and inclination, system and arrangements of rock packing behind longwall faces. In any given case the very many factors present have a mutual influence upon the effects produced in the mine. For example, a study of the effects of rate of advance cannot be done without considering the effects of other factors such as nature of strata, direction of face and quality and arrangement of supports. Conversely, the length and direction of a working face

Jan 1, 1947

By D. W. Philips

The problem of strata control has of necessity been prominent in mining, and accounts of individual experience and research abound in the literature of most mining countries. Organized rescarch began in Britain by the formation of a committee, upon the recommendation of the Safety in Mines Research Board in 1923, to investigate methods of reducing accidents from falls of roof in coal mines. This committee examined current practice in supporting underground workings in the principal coal fields, and its findings have been published in the Board's publications.' - Toward the end of these investigations it was suggested by the Chief Inspector of Mines that committees of the several mining institutes be formed to examine the problem in their respective districts. The formation of these committees marked a new phase in research on strata control. The work, though being done in the separate coal fields, followed a scheme outlined by the chief Mining Engineer of the Research Board, and was coordinated by his office. FACTORS INVOLVED The subject is being considered in Britain from two aspects: 1. To provide. by supports, means to prevent falls of fractured ground. 2. TO develop methods whereby the strata can be maintained in the least broken condition and thus make falls less likely. The first aspect is the one that will most likely lead to immediate results from the accident standpoint. It depends largely upon the assimilation of already acquired knowledge regarding the properties of supports and their correct application. The second aspect is perhaps more fundamental, and involves also the properties of the strata and their behavior under the influence of the forces induced by mining. The problem involves many natural factors that cannot be controlled, such as depth, inclination and thickness of seam and nature of the rocks. Other factors, which may be considered to a certain extent controllable, cannot be varied readily and with sufficient frequency to facilitate easy investigation; some of these are: rate of advance of the working face, length of face, direction of the face with regard to cleat and inclination, system and arrangements of rock packing behind longwall faces. In any given case the very many factors present have a mutual influence upon the effects produced in the mine. For example, a study of the effects of rate of advance cannot be done without considering the effects of other factors such as nature of strata, direction of face and quality and arrangement of supports. Conversely, the length and direction of a working face

Jan 1, 1947

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By Michel David

One of the most important questions that arises in ore estimation can be stated as follows: What is the error when one extends the grade of a sample to a certain volume? The theory of regionalized variables, with the concept of extension variance, provides a response to that crucial question for any kind of sample extended to any volume. For the usual "extensions" encountered in current mining practice, some simple results can be derived from that theory which was initiated by Dr. G. Matheron. These results have been applied to a stratiform lead-zinc deposit for which several estimations of grade, tonnage and related precision have been made for a series of grid sizes such as might be used in a progressive exploration program.

Jan 1, 1969

By A. W. Gauger

IT is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have 0n Society. The development of a machine to replace several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and technology as well as in the training of future engineers and technologists. MAGNITUDE OF THE FUELS INDUSTRY Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the comparative values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13 1/4 billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone annually exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1020 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to 1939, $46,409,727,000 of metallic products, S80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,000,000 of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our country. As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By M. E. V. Plummer, F. E. Beamish, J. C. Hole, J. M. Kavanagh

Prior researches have shown that the iron-copper-nickel content of platinum concentrates may be reduced by carbon to form a collecting alloy for the platinum metals in a manner exactly analogous to the formation of the lead fire assay button. The nature of the iron-copper-nickel alloys with the platinum metals has been investigated. Palladium and probably some of the other platinum metals form solid solutions with this alloy. ONE of the greatest known reserves of the platinum metals is to be found in the nickel, copper, iron sulphide deposits of Northern Ontario. The very large tonnage of copper-nickel ore processed makes the Sudbury district a significant world source of the platinum metals, the latter being recovered as byproducts in the electrolytic refining process for copper and nickel. Chalcopyrite, pentlandite, and pyrrhotite are carriers of the platinum metals;' these minerals contain from 0.03 to 2.0 ppm of the noble metals. The analysis of the above ores for the platinum metals necessitates an initial concentration of the minute quantities present in the ore. The method usually employed involves the extraction of the noble metals by molten lead with or without small proportions of silver. The lead is then separated from the precious metals by cupellation, a process which involves absorption by the cupel and volatilization of lead oxide, leaving the precious metals collected in a silver bead on the surface of the cupel. The collection by lead is probably achieved by a process of dissolution followed by some degree of segregation in the lead alloy since the cold button is seldom uniform in composition. With silver-lead alloys this process of liquation has been used to re- cover pure lead since, during the cooling period, crystals of pure lead separate and silver becomes concentrated toward the center of the solid.' Platinum and gold liquate in a manner similar to silver which may account for the successful recovery of platinum by fire assay even though it is considered insoluble in a solid lead medium. 3 In the case of iridium the liquation process may be a disadvantage in that the iridium may appear in the outer areas of the button and thus be lost mechanically during the handling processes. In any case the deficient alloying characteristics of lead for the platinum metals encouraged attempts to find an improved collecting alloy, and by analogy with aqueous extractions, preferably one in which solid solutions would be readily formed. Since, beyond a certain minimum solute to solvent ratio, the formation of a solid solution is accompanied by a lattice distortion, one would expect some relationship between the atomic diameters of any two metals and their tendency to form a solid solution. In one survey5 the hypothesis was put forward that when the atomic diameter of the solute differs by more than about 15 pct from the solvent, the "size factor" is unfavorable and the formation of a solid solution is restricted. On the other hand, when the atomic diameters are within this limit the size factor is favorable and solid solutions are readily formed, e.g. the transition metals of Group VIII having similar radii form solid solutions over wide ranges of composition.6 Even with a favorable size factor, elements having different crystal structures cannot form a continuous series of solid solutions. Cell dimensions alter as the concentration of the solute increases, causing a

Jan 1, 1962

By B. A. Kulp, R. R. Reeber

Lattice parameters for the wurtzite form of' CdS mere measured by powder X-ray diffraction techniques over the temperature range 26° to 1000 K'. A negative thermal -expansion coefficient was determined parallel and perpendicular to the c axis below 13.5°K. Near 808°K, the curves of the a, parameter, the differential thermal expansion, and the resistivitv vs absolute temperature exhibited a reversible discontinuity. j\. direct determination of the lattice parameters of CdS over an extended temperature range is of particular use in interpretation of the effects of high pressure on the band structure of semiconductor materials. For example, Langer' has studied the effects of pressure on the absorption edge of CdS from 77°K to room temperature. In order to properly interpret his results it is necessary to know the change in lattice constants as a function of temperature for the wurtzite, zincblende, and rocksalt2 modifications of this material. Thermal-expansion measurements for CdS, wurtzite phase, have previously been determined over a limited temperature range.s74'5 The zincblende phases, of other compounds with similar bonding, have been investigated by Novikova et a! .'' Previous thermal-expansion measurements for metals with hexagonal symmetry have for the most part used bulk sample techniques for low-temperature result. Most X-ray measurements at low temperature have been on materials with cubic symmetry.'jQ The use of X-ray powder-diffraction techniques offers a convenient and accurate method of measurement over a wide temperature range. The X-ray method, besides measuring unit cell size, also provides information about change in structure type and the nature of some of the stacking defects present. I) EXPERIMENTAL PROCEDURE The thermal expansion was measured by X-ray powder-diffraction techniques. Lattice parameters for the range 300" to 1000°K were determined in a 19-cm Unicam camera. From 26" to 300°K a 34-cm back-reflection camera with the Van Arkel" film arrangement was used. The sample was bonded to a copper cold finger below a helium, hydrogen, nitrogen, oxygen, dry ice, or ice brine bath in a metal cryistat. che inner bath was surrounded by another one for radiation shielding. Nitrogen was used in this outer bath for the very low-temperature runs while dry ice and acetone was used for the 195°K point. CuKa X-rays, filtered with a nickel foil, entered the cryostat through a 0.001-in.-thick aluminum window. During a typical 9-hr exposure the sample was continuously rotated through a 30-deg arc. Heat losses from the sample holder limited the minimum temperature attained to 26°K with helium in the inner dewar. Temperature calibration between 25" and 125°K was determined with an Allen Bradley 300-ohm carbon resistor. The resistor was attached to the back of the copper finger with a thin layer of silicone grease. Liquid He, HZ, N2, and O2 baths were used to calibrate the resistor. Temperature variation is estimated to be *2"K with a slightly higher uncertainty at room temperature and 264°K. The thermal expansion of high-purity germanium from 373" to 900°K was measured as a calibration for the Unicam camera. This value was compared with the known value1' for the thermal expansion. A discontinuity in the thermal-expansion coefficient of the CdS a, parameter was observed. Similar discontinuities in the resistivity and differential thermal analysis at the same absolute temperature indicate that the temperature error is *5°K in the temperature range above 500°K. Temperature errors in the Unicam camera below 500°K are appreciably higher due to large gradients in the resistance furnace. II) SAMPLE PREPARATION The CdS was Eagle Picher ultrapure grade. The crystallite size range of the as-received powder

Jan 1, 1965

By J. B. Coher, M. B. Bever

COLD work destroys long-range order, as was first observed by Dehlinger and Graf.1 Dahl2 showed that the mechanical disordering caused by cold work produces changes in those properties that are affected by long-range order. The existence of order has a marked effect on tile manner in which an alloy deforms and therefore on its mechanical properties.L' The relation between order and deformation behavior however, is only beginning to be understood. Seemann and G1ander4 suggested that cold work reduces an ordered alloy to a kind of gruel of antiphase domains. According to Cottrell,5 superdis-locations and pairs of dislocations in a slip plane connected by a strip of anti-phase domain boundary provide deformation mechanisms which do not change the state of order. In general, however, slip may be expected to produce new domain boundaries and destroy order if dislocations move on intersecting planes or cut through existing domain boundaries. The yield strength of an ordered alloy may pass through a maximum with decreasing domain size.5"7 The reduction of domain size resulting from cold work may, therefore, lead to a maximum in strength properties. Flinn8 suggests that dislocations can climb by short-range diffusion during deformation and thus can generate domain boundaries not only on slip planes, but also on other planes which will be those with the lowest domain-boundary energy. It has long been known that the rate of strain hardening of an alloy in the ordered state is larger than in the disordered state.3'9 Also the slip bands in ordered CU3, AU10 and Ni3Mn" are finer than in the disordered alloys. The stress which causes initial yielding in Cu,Au passes through a maximum with decreasing domain size.6'12 A maximum has also been observed in the hardness of ordered Ni3Mn as a function of strain.' These observations suggest, but do not prove, that domain size reduction occurs during deformation. According to Fisher13 slip destroys short-range order and thus the strength of an alloy is related to the degree of short-range order present. Rudman and Averbach14 and Averbach et a1.,15 demonstrated that cold work reduces short-range order in copper-gold and gold-silver alloys. Destruction of long-range and short-range order by cold work implies slip on an appreciable fraction of planes. Yielding of an alloy in which short-range order exists or antiphase domain boundaries are present should be discontinuous because the first dislocations moving across the slip plane meet with the largest resistance.5 Such discontinuous yielding has been observed in CU3AU6,16 and Cuzn.l7 This phenomenon, however, can also be explained by mechanisms not involving order.b The published investigations of the effects of cold work on alloys with long-range or short-range order have not been covered thoroughly in reviews of order-disorder phenomena. These investigations, therefore, will be listed here. They have been concerned with strength properties> 2,3,6,8,9,12,16-21 electrical resistivity,2,4,18,19,21-26: thermoelectric power, magnetic properties,2,18,21,26 and X-ray strain'1,2,14,15,27,28 The slip systems and the appearance of the microstructure after deformation in ordered and disordered alloys have also been investigated. 6.10.ll,l7,23,29,30 The alloys used in these investigations were copper-gold. 1-4,6,9,10,14,16,18 23-26,28,29 copper-zinc. L7. 19. 20,30 nickel-manganese,2 11,21 iron-aluminum. iron-nickel,' copper palladium,4,18,22 gold-silver.4,18,22 and palladium-silver-copper.4 In the work reported here. the changes in properties of polycrystalline Cu3Au were investigated as functions of strain in wire drawing and rolling. Specimens were heat treated before deformation

Jan 1, 1961

By Robert C. Paddock

INTRODUCTION A way of producing 3,000 tpd from the El Mochito Mine was needed. Of this production, 2,000 tpd must come from the San Juan orebody. The original sub-level stoping method did not give satisfactory results due to ground instability, and the highly irregular ore/waste contacts encountered . The experience gained from the initial system helped guide research into the ground instability problem. Results from this work, combined with knowledge gained about the orebcdy configuration, defined constraints that were previously not fully appreciated. These constraints, and others, combined with objectives, were considered together to develop a new mining method. No single technique was found to be suitable, so a hybrid mining system was developed. A combination of ramping, cut and fill, and vertical crater retreat, with an option to use top heading and benching was developed. To complement the mining system, the type of equipment needed was decided upoun. Also, to support the mining system at this expanded rate of product ion, major modifications of existing infrastructure were required. THE EL MOCHITO MINE The El Mochito Mine, of Rosario Resources Corporation, has been in continuous product ion since 198. The mine began operations in April of that yeas at a rate of 100 tpd. The reserves in 198 were 100,000 tons of silver ore assayed at 1,250 grams per tonne. As of the end of 1979, the El Mochito orebodies have produced over 5.6 million tonnes of ore averaging 516 grams per tonne silver, 6.8 lead, and 7.8% zinc. Present ore reserves are about 7.9 million tonnes, averaging 138 grams per tonne silver, 4.6% lead, and 8.7% zinc, with minor quantities of copper, cadmium and gold. An expansion plan to increase mill production two fold to 2,500 tonnes per day is underway. This expansion will require the mine to produce 3,000 tpd. The mine consists of numerous orebodies, all of which have been mined to a certain extent. Of all the orebodies, the San Juan contains 8% of known reserves. This amounts to about 6.7 million tonnes. The significance of the San Juan orebody to the future life of the El Mochito Mine is obvious. If the required mine production of 3,000 tpd is to be sustained, the San Juan must be the source of the majority of that production. Due to the mineability and overall logistics concerned with the other orebodies, the San Juan must be able to reach and maintain a production rate of 2,000 tpd by 1982. GEOLOGY OF THE SAN JUAN OREBODY The El Mochito Mine is a classic example of a chimney replacement deposit in limestone. Similar deposits axe found in Mexico, at the Naica, Providencia, and Santa Eulia Mines. The El Mochito Mine is located at the south- western end of the Sula Valley on the western edge of the Honduras Depression in the Central Cordillera and Central Highlands of Honduras in a setting of Mesozoic sediments. The orebodies occur in a structural basin developed between NNE trending normal faults and apparently hinged on the south end. Topographically, the Mochito Basin lies between the uplifted Santa Barbara mountain in the west and the Palmer Ridge on the east. The San Juan orebody occurs near the intersection of the NE trending San Juan fault and the ENE trending Porvenir fault. The downward continuation of the orebody is controlled by the westward rake of these NW and N dipping structures. The discovery of the San Juan orebody is attributed to analysis of structural evidence of known ore deposits by in-company geologists. The composition of the San Juan orebody is primarily garnet skarn, with local concentrations of hedenbergite and magnetite. The economically important sulfide mineralization consists of (in decreasing abundance), sphalerite , galena, pyrrhotite , and chalcopyrite. There is some indication that a Cu-Ag mineral such as tetrahedrite may also be present. The skarns were formed by replacement of the original limestone by hydrothermal water migrating upward roughly along the intersection between the Porvenir fault system and the San Juan fault system. Textural evidence suggests that the orebody is a composite of several pulses of hydrothermal activity which would explain, in pat, the great irregularity of the contacts and the large horizontal variation in mineralogy. A general pattern of skarn types can be seen in the orebody, partially accounting for the observed lateral variation in grades. This zonation is very generalized, and one or more zones may be missing in any given locality. The orebody is almost invaxiably surrounded by a 2 cm to 25 cm zone of bustamite skaxn with low values. The border skarn is usually

Jan 1, 1981