Search Documents

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. O. Hofman

(Canal Zone Meeting, November, 19]0.) THE sudden decease, April 1, 1910, in Chicago, of Dr. Franklin R. Carpenter was a shock to his- many friends. He died in his sixty-second year, of heart paralysis. To most fellow-members of the Institute who have followed the progress of the. last twenty-five years in the mining and treatment of non-ferrous ores, the work of Dr. Carpenter in that line is familiar ; but very few, even of those who knew him well in the later years, are acquainted with his earlier struggles to satisfy an inborn hunger for knowledge. The story of his life resembles that of the pioneer who opens up new country; overcoming hardships with indomitable courage, meeting doubts and difficulties with an alert and open mind, and exercising in the face of reverses an unconquerable perseverance. It seems appropriate to place on record in the Transactions a brief outline of the life and work of this eminent engineer. During the past 15 years of his life Dr. Carpenter was much interested in genealogy. In the pursuit of this study as an avocation, he traced his own ancestry to the time when ?Hugh," called "le Charpentier" on account of the dexterity with which he had swung his battle-axe as a crusader, settled in Sussex on lands received from William the Conqueror. The Carpenters came to this country with William Penn. A prominent member of the family was Joshua Carpenter, the founder of Christ Church, Philadelphia. Dr. Carpenter's branch of -the family moved from Pennsylvania into that part of Virginia which is now West Virginia, where his grandfather settled in Harrison county, while the grand-uncle went further west, and built the first iron-furnace at Hanging Rock, Lawrence county, Ohio. In fact, since early times, the Carpenters appear to have been iron-masters. Franklin R.. Carpenter was born, Nov. 5, 1848, in Parkers-

Aug 1, 1910

By Jim F. Lemons

INTRODUCTION A nickel doesn't buy much anymore. That's even true in the cost of recovering nickel -- the commodity. A 5[C] per pound (11 [c] per kilogram) increase in the nickel price won't cover a 10-percent increase in fuel costs for processing laterite ores, nor will it cover a 10- percent increase in wages for recovering nickel from a sulphide ore. It won't even cover a 5- percent increase in the capital cost necessary to mine and process ocean nodules. The basis for this statement and a quantitative analysis of the variations in costs to recover nickel from different types of nickel ores will be discussed in this paper. During the early part of the 1970's, the interest in nickel and its potential development was shifting from Canada to the Pacific Basin area. Canadian growth rate was slowing and each additional increase in nickel capacity was very expensive (Argall, G.O., 1970). Laterite ores were attractive to developers since they were easy to mine at a low labor cost, and technologies were being developed that would allow the recovery of nickel in marketable forms (Mohide, T.P., Warden, C.L., Mason, J.D., 1977). During the last decade, new laterite production was achieved in the Philippines and Botswana, and a significant increase in production from Indonesia and New Caledonia occurred. However, recent reports on nickel identify numerous problems plaguing the industry, i.e., high energy costs that are forcing shutdowns (INCO, 1980), (Mohide, T.P., Warden, C.L., Mason, J.D., 1977), high Canadian sulphide mining labor costs (Anon., 1976), and rapid inflation of nickel capital costs (Anon., 1981b). No definitive study has been made to determine how sensitive the total cost of production is to rising energy, labor, or capital costs, or to identify to what extent increased byproduct revenues could be used to offset these production costs. The purpose of this paper is to quantify the effects of increases in energy, labor, capital costs, and by-product credits on the future cost of production from nickel reserves and/or resources. METHODOLOGY OF ANALYSIS In order to evaluate the sensitivity of nickel production costs to changes in energy, labor, and capital costs, and in byproduct revenues, an analysis was made of existing and proposed nickel operations, their costs, and their sensitivity to change. The data for these analyses were obtained from numerous sources including international govern¬ment and university publications, professional journals, company reports, private communications, U.S. Bureau of Mines contracts, and estimates by Bureau of Mines personnel. These data were collected, in part, as an ongoing effort of the U.S. Bureau of Mines Minerals Availability System (MAS) to systematically measure and classify identified mineral resources according to their respective extraction technologies, economics, and commercial availability. The MAS Program is currently evaluating the present and potential availability of nickel to the United States in relation to mining, beneficiation, smelting, refining, leaching, transportation, infrastructure, environment, land use, labor, productivity, technology efficiencies, operating capacities, deposit life, and political factors. As a summary of this data, the following briefly describes nickel ore types as each relates to energy, labor, capital, and byproducts. Sulphide Operations Nickel is currently available from sulphide deposits. Roughly 55 percent of the current world nickel production in market economy countries is from sulphide ores, although only about 20 percent of the known land-based nickel reserves and/or resources are sulphides (INCO, 1981). In 1979, the Western World sulphide reserves were estimated at about 9.2 million metric tons of nickel (Little, A.D., 1979). Sulphide ores are typically mined underground, thus resulting in high mining costs; however, these ores can often be upgraded by flotation prior to final nickel recovery and require about one-third of the energy required to recover nickel from laterites (Anon., 1981c). In addition, nickel in sulphide ores may be associated with economically recoverable byproducts, which include copper, cobalt, gold, silver, and other precious metals. Laterite Operations Forty-five percent of current nickel production is from laterite deposits. Laterite deposits account for 80 percent of the known land-based nickel reserves and/or resources (INCO, 1981). In 1979, the Western World laterite reserves were estimated at over 35 million metric tons of nickel (Little, A.D., 1979). Nickeliferrous laterites are residual soils formed by weathering, typically under tropical or near tropical conditions. They can be easily mined by open-cut methods, but generally cannot be beneficiated; thus, recovery of nickel must entail processing of the total mined ore. Usually, these ores have high moisture content (20 to 30 percent by weight) that result in additional fuel costs to dry the ore. Nickel silicates, garnierites, are, processed by pyrometallurgical methods; limonite nickel oxides are normally leached. Byproduct cobalt is not recovered from most ferronickel operations, and is only recovered to a limited extent from many leach operations.

Jan 1, 1982

By AIME AIME

No democracy such as ours, can ever be prepared for war, because we could never conceivably be the aggressor. The aggressor prepares in secret, designs his new tactics, and invents and makes new equipment and selects the time to strike. If a democracy prepare done year and the war came later, all that it had one would have to bed one over. All that England has today in the way of effective armament has been invented, designed, made, and the crews trained since the war began, because the totalitarian aggressor introduced new types of equipment and new techniques.

Jan 1, 1941

By W. M. Myers

MINERAL Economics is the most recent profession to be recognized as a separate division of the mineral industries. It has originated from the increasing awareness of the importance of the economic aspects of industries concerned with discovery, extraction, and utilization of minerals. It is concerned with the interrelated fields of economics and technology. The individual trained in economics alone cannot qualify. The curriculum in the School of Mineral Industries at The Pennsylvania State College was approved in May 1946, and enrollment begun in September of that year. Due to the transfer of advanced students from other courses, particularly metallurgy and electrical engineering, it was possible to graduate the first seniors in June 1947. The next class was graduated in February 1948. From experience derived from placing these graduates in industry, and from information supplied by prospective employers, valuable data have been obtained in the organization and operation of the course of study.

Jan 1, 1948

By John S. Crandall

Occurrence: small crystals in alluvial sands from the eroding Belt Series mica schists. Flowsheet: dragline, trommel screen, jigs, drier, crusher, screens. Value: ground, $2.50 per cu yd, garnet sand gross $60. per ton. Costs: production and sales $48. per ton. Uses: blasting sand in aircraft plants, monumental works, foundries. Efficiency comparison: superior to silica sand. Future: possibilities only touched upon, research continuing.

Jan 1, 1950

By Hans Lundberg

AFTER the war years, great activity has been shown in geophysical exploration for ore. The appreciation by mining and government geologists of geophysical techniques and results is largely responsible for the popularity of these methods. In Canada, plans are being made to study, by geophysical methods, the structure of a portion of the Pre-Cambrian shield in the hope that such studies will not only give a clearer picture of the geology, but will be of direct aid to the mining companies when selecting areas for detailed prospecting. Although geophysics thus has become more popular, some engineers are still reluctant to employ the methods to their full extent. Allotted funds are often rather low, so that the least expensive

Jan 1, 1947

By E. R. Kaiser

ACTIVITY on long-range and on immediate wartime problems shared the attention of specialists in coal research during 1943. Programs of the principal coal laboratories were more adequately financed than in previous years, but all reported shortages of technical personnel. Expansion in coal research in the year to come will depend primarily on the availability of qualified research talent.

Jan 1, 1944

By R. M. Waterstrat, E. C. van Reuth

BINARY- alloy phases having the A15-type crystal structure have been described as occurring at a simple and more or less invariant stoichiometric composition (A3B) which corresponds to the relative number of atoms occupying each of the two crystallographi lattice sites in this structure.1,2 It is frequently assumed, therefore, that each crystallographic site is occupied exclusively by one kind of atom. In most cases, however, there have been insufficient experimental data to establish whether atomic ordering is, in fact, complete. Recent studies have shown that binary A15-type phases are sometimes stable over an appreciable composition range3''* and, occasionally, the composition range of stability does not even include the "ideal" A3B stoichiometric composition.5-7 We have observed the existence of nonstoichiometric A15-type phases in the binary systems Cr-Pt and Cr-Os. This has not been reported in previous work on these alloy systems.1,8-11 A series of alloys, each weighing approximately 30 g, was prepared by are-melting in an Ar-He atmosphere using 99.999 pct Cr, 99.999 pct Os, and 99.99 pct Pt as starting materials. Each alloy was melted four times with a total weight loss of less than 1 pct. The stoichiometric (A3B) alloys were sealed in evacuated quartz tubes and annealed at 1200°C for periods of time ranging from 3 days to 2 months. Examination of the alloy microstructures revealed that little change had occurred over this time interval and it was therefore assumed that the microstructures were fairly representative of equilibrium conditions. No evidence of contamination was observed although there was apparently some loss of chromium which was confined to a thin layer at the surface of the specimens. The quartz tubes were quenched from the annealing temperature into cold water. X-ray diffraction and metallographic examination of the stoichiometric alloys revealed an estimated 10 to 30 pct of second phases which were tentatively identified as phases previously reported in these binary-alloy systems.8-11 A second series of alloys was prepared by mixing -325 mesh metal powders having a nominal purity of 99.9 pct and compressing these mixed powders in a cylindrical die at a pressure of 43,000 psi. These alloys, each weighing 15 g, and some of the arc-melted alloys were annealed in a high-temperature vacuum furnace heated by tantalum strips at a pressure of 10-8 Torr and were rapidly cooled by turning off the furnace power. X-ray and metallographic examination of both series of alloys served to establish the composition ranges of the A15-type phases. Although some chromium losses occurred during the vacuum annealing, they were largely confined to a thin layer on the outer surfaces of the samples. It was established that the A15 phases occur in the Cr-Pt system at 21 ± 1 at. pct Pt after 1 week at 1200°C and in the Cr-Os system at 28 ± 1 at. pctOs after 1 day at 1400°C (see Table I). We also observed that an arc-melted stoichiometric (A3B) alloy in the Cr-Ir system was single-phase (A15-type) in the "as-cast" condition in agreement with previous work.8,13 In addition we obtained a sample of the Cr-Os A15-type phase from Argonne National Laboratory. This alloy contained less than 1 pct second phase12 and was submitted to a density measurement. The density measurement yielded a value of 11.14 g per cu cm in comparison to a theoretical value of 11.25 g per cu cm calculated using the observed lattice constant (4.6806Å) of this alloy. The uncertainty in measurement was 0.1 pct but the sample may have contained some cracks or minor imperfections which could account for the low experimental value. We have also studied the atomic ordering in these phases by means of integrated line intensity measurements using thick, flat, rotating powder samples and CuK a radiation in an X-ray diffractometer. We have obtained order parameters of 0.90 for the Cr-Pt phase, 0.89 for the Cr-Ir phase, and 0.64 for the Cr-Os phase using the formula: where s is the usual Bragg and Williams order parameter, ra is the fraction of chromium atoms in A sites, and FA is the fraction of chromium atoms in the alloy. The values obtained are estimated to be accurate within ±4 pct. If the unusually small value for the order parameter of the Cr-Os A15 phase were due to the existence of lattice vacancies on the "B-atom" sites, then a density of 10.04 g per cu cm would be expected in contrast to the observed value of 11.14 g per cu cm. We, therefore. conclude that the fraction of lattice vacan-

Jan 1, 1967

By Carl Heinrich

I HAVE read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: Horn Silver Slags Oxygen(b) Oxygen(b) Average of I and. II Slag I percentage Slag II percentage Oxygen Si02 33.9 18.1 .35.0 18.7 34.50 18.40 FeO 26.8 6.0 25.4 5.7 26.10 5.80 CaO 26.1 7.5 24.9 7.1 25.50 7.30 BaO 3.2 (a) 0.3 3.2 0.3 3.20 0.30 A1203 10.8 5.1 9.3 4.4. 10.05 4.75 100.8 37.0 97.8 36.2

Jan 10, 1916

By D. J. Cox, J. P. Conway, A. E. Gooch

A two-year test conducted by the USBM's Spokane Mining Research Center (SMRC) has proven the feasibility of the yielding rockbolt, a concept which may prove very useful to the mining industry by providing ground support under a variety of conditions. The yielding rockbolt was originally developed in South Africa3 to overcome the limitations of conventional bolting in rock subjected to high-stress or rock burst conditions. The yielding effect is obtained by fitting the bolt prior to thread rolling with a smooth-bore die of internal diameter slightly larger than the shank diameter but smaller than the rolled thread diameter.

Jan 4, 1977

Seattle offered sunny, dry weather to about 2500 mining men who assembled September 10 to 14 for the 1961 American Mining Congress. The impact of snappy sessions on national mineral policy, state of the industry and foreign competition (to name only a few) was somewhat overshadowed by enthusiasm of conventioners for salmon fishing. This lordly fish, which mysteriously runs to its hatching place to spawn and die at this time of year, was not cooperating with the anglers in Puget Sound. However, this did not prevent consuming ample amounts of the deliciously prepared Quinault salmon at the "Potlatch" celebration.

Jan 10, 1961

By AIME AIME

REPUBLIC STEEL'S new iron blast furnace in Alabama, shown on the cover of this issue, is the first to be completed of those authorized by the Government last year when a shortage of scrap became acute. In addition to the furnace, the new equipment includes a new battery of by-product coke ovens, a boiler plant, a generating unit, a 3-mile-long 60-in. water line, a huge gas washer, and precipitators in which the dust from the furnace is washed, separated from the water, and fed back into the furnace as raw material. The new unit is a cylindrical steel giant reaching 130 ft. into the air above the ground level. Because of the high humidity in the deep South, the furnace has been air-conditioned to avoid blowing eighteen tons of water into the furnace daily. Designed by Republic engineers who also had charge of the actual construction, the new furnace incorporates the best in modern blastfurnace practice. Orders to proceed with the construction of the furnace were received Sept. 22, 1941. The engineering crew, which was immediately organized, made more than 1500 drawings. Excavation started the next day, and simultaneously work was begun on demolishing existing buildings and preparing the site. The first concrete was poured Oct. 7 and the first piece of steel swung into place by a giant derrick on Jan. 30, 1942. It began operating May 28. A total of 70,000 cu. yd. of earth was moved and 30,000 cu. yd. of concrete poured.

Jan 1, 1942

By H. Stigzelius

FINLAND'S recent mining history is both dramatic and pitiful in its shifting fortunes, dominated as it has been, by the country's proximity to the border zone of opposing dictatorships and social traditions; Fascism to the south, Communism to the east, and Democracy to the west. After 108 years under Russia's more or less harsh rule, Finland gained its democratic independence during the 1917 revolutionary strife in Russia with the official help of Germany and spontaneous help of other neighbors. The young nation was attacked by Russia in 1939 and again in 1941. It is common knowledge how the Finns fought with everything they had and everything they could get against their overwhelming adversary, and how by force of circumstances they landed in the Axis camp in 1941. Finland has never been known as a mining country in the same way as near-by Sweden, whose abundant iron and copper smelters during long periods so greatly contributed to the nation's welfare. Its largely barren, Archaean-granite geology long seemed forbidding. Some mining was done, to be sure; copper and tin at Pitkaranta near the Russian border, and lead and copper at Orijarvi. But towards the end of the last century the absence of a single producing mine cast a pessimistic shadow of truth over the Finnish poet Runeberg's words, that

Jan 1, 1946

By AIME AIME

Gentlemen, we have ten questions on our list and a number of us here probably have other questions to ask. Therefore, we arc going to allocate the time to these different questions so that we will try to be finished by 4:30; from then until 5 o'clock, if any of you have any questions on subjects not related, you will be free to ask them. Mr. Morton and I have changed the order of the questions. Instead of what is now first, we have put No. 3 first, progress on basic-roof construction, inasmuch as we feel that it is quite important. At this time, H. S. Robertson, of Harbison-Walker, is going to give you a short talk, with slides, on what has been done to date on this subject.

Jan 1, 1940

By W. S. Morris

THE East Texas oil field is the largest in the United States and perhaps the largest 'in the world ; likewise, it is one of the most interesting. The East Texas oil field is a water-drive field. Small amounts of salt water were produced from wells on the western side of the field from the bt-ginning of the development. By the end of 1933 (the field having been discovered in September 1930) water production had reached 9000 barrels per day. By the end of 1936, approximately 2000 wells were producing about 45,000 barrels of water per day, and the problem of salt water disposal attracted the serious attention of the operators. Salt water production in the field has steadily increased and today approximately 450,000 barrels of water per day is produced while the oil production averages about 375,000 barrels. The disposal of this salt water has therefore become one of the major operating problems. Various methods of salt water disposal have been tried in the East Texas field. Evaporation in open pits proved

Jan 1, 1944

Jan 1, 1880

By Michael Tenenbaum

A REVIEW of process metallurgy of iron and steel during 1944 in many ways reflects the political and military developments of the year. Early in 1944 the tremendous wartime emergency expansion program was virtually completed and the industry directed its efforts to maintaining maximum production wherever needed. The vigorous production programs inaugurated to support the Normandy invasions did not persist as Allied armies approached Germany. General public apathy which developed with the prospect of an early ending of the European fighting was reflected in a general relaxation in armament programs. Toward the end of the year, as the prospect of a prolonged war became real, the entire program revived considerably and the need for steel became acute. Between January 1940 and October 1944 more than 12,400,000 tons had been added to the nation's steelmaking capacities, and over 12,700,000 tons added to the blast-furnace facilities. The total cost of this enormous program was more than two billion dollars. By July 1, 1944, total steelmaking capacity had exceeded 94,000,000 tons, with blast-furnace capacity rated at 68,400,000. Annual steel production, which was 88,900,000 tons in 1943, increased slightly during the past year and was estimated at 89,500,000. Production of pig iron also increased somewhat from 61,800,000 tons in 1943 to an estimated output of 62,500,000 in 1944. This review deals with a few of the numerous factors involved in maintaining the wartime iron and steel program at the level necessary to accomplish this enormous output.

Jan 1, 1945

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926

By CLARENCE WM. POY

THE most common difficulty faced by an engineer or mine operator when opening a new property in a new field is the lack of roads and of cheap transportation. This one item often swings the balance of success or failure in starting a project. In Alaska, as elsewhere, such problems are more or less serious. In the boom days around the Valdez district, as well as in other parts of this territory, freighting was accom¬plished by dog teams or horses, or even by men that were willing to put their shoulders into harness, because there were virtually no roads. More important, there was only one time when supplies could be transported, and that was when there was suffi¬cient snow on the ground following a heavy wind. Then, and only then, could one depend on the snow to support horses and sleighs, and be sure that the gulleys, streams, and crevices in the glaciers were filled with snow to avoid pitfalls. These methods were used when one had no roads, no streams in the summer to float a barge, or even a trail for a pack train. If the snow was deep and soft, trans

Jan 1, 1935