Search Documents

By Jorge Madias

Pin holes as a surface defect, and blow holes as an inner defect, occur in billet / bloom / beam blank casting, particularly for Si-Mn killed steel cast with metering nozzle and oil lubrication. If they are present in abundance or have a large size, they may originate defects in the rolled products. Their characteristics, factors behind their formation, as well as usual processing conditions that promote their occurrence are discussed. Finally, the evolution of these defects during reheating and rolling is analyzed, with industrial examples.

Aug 16, 2017

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019

By Luiz Alberto dos Santos

. In this work, samples of the alloy with composition of 50.9 % at. Ni were machined and were subjected to hot tensile test, after the machining all the samples were solubilized so that all were in the same condition during the hot tensile test. The hot tensile tests were performed between the temperatures 350-650°C and the yield stress were between 800 and 597.1 MPa and area reduction between 17 and 75% with respect to the initial area. The test at 350°C shows a fragile fracture characteristic while the hot tensile test above this temperature showed a predominantly ductile fracture. The fragile fracture is evidenced by the river marks that are characteristic of this type of fracture, because in this condition does not promote much plastic deformation. The higher temperatures present ductile fracture, because present the dimples that also characterize this type of fracture. This work shows the temperature relationship in the mechanical properties, more specifically the hot tensile test, in the NiTi alloy.

Oct 30, 2017

By Anna Carolina Cerqueira Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Aug 16, 2017

By Flávio Beneduce Neto

As trincas a quente ou de solidificação em peças micro-fundidas em superligas a base de níquel podem ser um item importante no índice de perdas em componentes específicos. O aparecimento desse defeito está ligado fundamentalmente à quantidade de líquido interdentrítico nos últimos estágios da solidificação e, principalmente, ligado à composição química desse líquido. Há duas ligas amplamente utilizadas na produção de rotores para turbo-compressores ou turbinas para a geração de energia: o Inconel 713C e o Inconel 713LC. A diferença entre estas duas ligas é essencialmente o teor de carbono. Curiosamente, a liga LC tem uma maior tendência ao aparecimento de trincas de solidificação. O presente trabalho procura identificar as diferenças de comportamento na solidificação dessas duas ligas através da termodinâmica computacional e ligar essas diferenças no aparecimento das trincas. Os resultados indicaram que os teores de Zr e Nb do líquido remanescente da solidificação são muito superiores na liga LC causados pelo atraso na precipitação dos carbonetos tipo MC nessa região que deve ser a fase que aumenta a resistência mecânica da área. O correto balanceamento da composição química da liga em relação aos elementos citados permitiu que o índice de perdas por trincas de solidificação caísse para níveis próximos a zero.

Aug 8, 2018

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019

By Felipe Darabas Rzatki

Polyether ether ketone (PEEK) is a high performance thermoplastic often selected for high temperature tribological applications under chemically aggressive environments. The present work evaluate the tribological behavior of a high performance PEEK composite under ambient and high temperature (30 and 80°C, respectively). The atmosphere was also varied (air or tetrafluorethane). An AMTI tribometer equipped with a hermetic chamber and a heating system was used to carry out sliding tests of PEEK cylinders on 304 stainless steel polished discs (Sq < 10 nm) with reciprocating movement and 175 N normal force. Surfaces roughness analyses were performed with a white light interferometer. As expected, there was a strong influence of temperature on the tribological behavior of the samples tested in ambient atmosphere (25% decrease in friction coefficient associated with a 100% increase in wear rate). On the other hand, samples tested in tetrafluorethane atmosphere showed no significant friction temperature dependence.

Jul 31, 2018

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Larissa Agrizzi Ronqueti

The effect of coiling temperature on selective oxidation behaviour of binary and ternary iron-based model alloys containing different contents of Si or Mn were investigated by SEM and SIMS. The experiments were carried out with a temperature ranging from 450 °C to 700 °C, under N2-5%H2 gas flow with a Dew Point of -3.3°C, for different durations. SEM images of binary iron-based model alloys revealed a decrease of grain boundary oxidation depth with increasing Silicon or Manganese content. At 530°C and 600°C SIMS results showed no Silicon diffusion toward surface, contrary to the results analyzed for Fe-x%Mn. Tests results and Wagner’s theory application (specific cases Fe-0.2%Si and Fe-0.5%Si) showed that grain boundary oxygen diffusion coefficient “DoGB” is almost 60 to 70 times faster than oxygen bulk diffusion coefficient. These results helped to broaden knowledge of single-element effects on grain boundary oxidation, in addition, will contribute of the future works in new steels with complex alloy compositions.

Aug 17, 2017

By Alim Ullah

The paper discusses the necessity of upgrading low-iron containing ores, giving as an example, NML-Tata Steel Project in the Quebec-Labrador region of Canada. As cooling of pellets is generally a bottle-neck in most pelletizing plants, examples are given of the methods used to improve cooling in the existing plants and a simple, low-cost alternative, tested on a pot-grate system, is presented. The procedure described is applicable to sinter plants also. The trends in iron and steel production worldwide are then given, as well as the reasons for the increase in steel production by the Electric Arc Furnace (EAF) route. The stoichiometric and thermodynamic requirements for producing iron, irrespective of the process, are explained. The different ironmaking processes, especially the Direct Reduction (DR) ones are briefly discussed, outlining recent improvements made to some of them. The pros and cons of producing cooled DRI and Hot-Briquetted Iron (HBI) are given with predictions made for their future growth. An alternative to cold-briquetting of DRI fines is also discussed. Highlights of an ironmaking processes which is at the laboratory/pilot plant stage are given.

Aug 1, 2018

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Andreas Rohrhofer

Reliable high end automation and process optimization systems are main factors for excellent product quality, safe operation and maximized plant performance in the steel industry and its designated environmental plants. Primetals Technologies introduces new automation packages for consequent safe and cost efficient production. Many areas within the steelplant interested to be monitored and measured automatically are not implemented in the automation system due to limited access or technical reasons. A wireless, self-organizing network facilitates wide ranging data transmission in previously inaccessible areas and opens up a wide range of new opportunities. With Fluid Guard a system to detect leakages with highest accuracy and reacts properly for all kind of water cooled circuits is available, improving the safety in steelmaking process. Lance Guard can be utilized for all fully automatic and semi-automatic lance appliances, but is especially suitable for the products of Primetals Sublance Standard/2.0 and LiquiRob applications, since these systems make seamless integration particularly simple. Manual lance appliances may also be tested and diagnosed. Environmental plants have become a main part in steelmaking plants. Highest performance in combination with optimized energy consumption is the main target in Primetals Technologies’ innovations in automation optimization packages for dedusting systems. A new approach for preventive maintenance and operator assistance is introduced with the Acoustic Expert System. In combination with the new Ask cloud based system, Primetals enables a 24/7 monitoring and a whole lifetime observation of any equipment within a steelplant. Furthermore it is now enabled to check the condition of the plant at a fingertip at any time.

Aug 17, 2017

By Steven G. Jansto

Nearly one third of the globally produced structural flat and long structural products are in the 0.11 to 0.16% carbon range. By definition, numerous steelmakers globally define this approximate carbon range as peritectic in their melting grade family within their organization. The metallurgical consequence is the result of numerous global structural specifications which allow carbon to wide carbon ranges resulting in quality issues. For example, such specifications as ASTM A588 set no minimum carbon and a 0.15 to 0.19%C maximum depending on the specific grade designated within the specification. This peritectic region is specifically challenging in production compared to less than 0.10%C because of solidification issues and a higher propensity for slab or billet cracking during continuous casting. During hot rolling, rejects and/or deviates are increased as well. The relative steelmaking operational cost of production is compared between peritectic and non-peritectic carbon compositions for a given specification.

Aug 17, 2017

By Sunil Katharia

In February 2016, the upgraded Blast Furnace 1 of JSW Steel Limited (JSW) at its Vijayanagar Steel Plant was blown in after a 6 months shutdown in which the whole furnace was rebuilt on the existing foundation and within the existing tower structure. Despite several plant constraints it was possible to increase the furnace inner volume by 85% - reaching 2307 m3 from existing 1250m3. The upgradation project covered the stockhouse and its dedusting system, top charging system, furnace profile, furnace cooling system, casthouse and its dedusting system, slag granulation plant, pulverized coal injection plant, hot blast system and gas cleaning plant – with major interventions in order to cope up with the changed operating conditions. The total scope of the project was split by JSW into several packages, all based on design data provided by Paul Wurth. JSW was responsible for coordinating the local subcontractors along with Paul Wurth which has been appointed as main technology supplier in charge of complete basic and selected detail engineering in the key areas and of the supply of core equipment such as the Bell-less Top®, copper staves, GCP key items and TMT casthouse machines. The main design concept and the key points of the project such as optimization of project ROI, advanced erection concepts as well as a summary of the operating results are presented confirming JSW “BF1” upgradation as one latest examples of the current state of the art in the revamping projects.

Aug 17, 2017

By Guilherme Corrêa Soares

The effects of temperature and strain rate on the mechanical behavior of a superelastic NiTi wire were investigated by uniaxial tensile testing. A universal testing machine with an attached heating chamber was used for the tensile tests. Temperature influence was studied through straining of samples until rupture at a fixed strain rate and temperatures of 25, 50, 75, 100, 125, 150, 175 and 200 °C. Strain rate effects were investigated by straining samples until rupture at room temperature and strain rates of 10-2, 5 x10-3 , 10-3, 5 x 10-4 and 10-4 s-1. The effects of temperature and strain rate on NiTi mechanical behavior were discussed in terms of critical stress to induce martensite and austenite yield strength, when applicable; upper plateau stress, transformation plateau length and ultimate plateau stress. It was found that increasing test temperature and strain rate shifted the stress-strain curve upwards, albeit temperature displayed a greater influence. Plateau length increased with temperature, but no significant changes were detected as a result of different strain rates.

Aug 17, 2017

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By Alberto Lainati

The Bar Reducing and Sizing Technology has a core function in the value-chain for the production of rolled SBQ (Special Bar Quality) products. The EVO 2+4-roll is based on the compact combination of a 2-roll high-reduction module followed by a 4- roll low-reduction module for precise sizing. The EVO 2+4-roll mill, allows to gain significant technical and economical advantages in the hot- and post-rolling process routes: dimensional and surface accuracy, quick adaptability to processing variances and to small lots requirements, superior technological features of as-rolled product, competitive capex and opex. The EVO 2+4 unit has a very compact design, which makes it suitable both for new mills and upgrade applications.

Aug 17, 2017

By Márcia Maria da Silva Monteiro Pereira

Tundish is the last reactor where significant metallurgical operations can still be done. Calcium aluminate slags are able to positively contribute to metallurgy considering oxide separation, protection against reoxidation and preclusion of resulphurisation. However, these are poor insulators. When using low melting point slags it is necessary to use another covering material. The deviation from saturation can be used as a measure of absorption capacity. By utilizing computerized construction of ternary and quaternary diagrams it is possible to compare different slags and to find proper slag compositions with reasonable capacity to dissolve inclusions. Objective of the present technical contribution is to evaluate tundish slag capacity to absorb inclusions, considering a particular tundish industrial slag and the changes in its chemical composition during continuous casting of steel. It was observed that slag composition changed during the continuous casting process; this variation is possibly related to interaction between the CaO-Al2O3 liquid slag and the rice hull ash layer which is used above it. Computational thermodynamics was used to determine activity of alumina dissolved in liquid slag; it was observed that the variation in slag composition did not change slag capacity to absorb inclusions, since precipitation of Al2O3 solid phases is not predicted.

Aug 17, 2017

By Saul Garcia Hernandez

The research work objective is to study a new ladle shroud internal design to reduce the slag emulsification in the tundish during ladle transient periods. A 3D mathematical model of the tundish was created to solve the fundamental equations, a turbulence model, and a multiphase model. The results show that using a conventional ladle shroud, the fluid is delivered with an excessive amount of kinetic energy being dissipated inside the tundish bath, generating strong mixing flow patterns and entrapping a massive amount of slag. In the other hand, the proposed ladle shroud dissipates the kinetic energy before the fluid enters the tundish promoting less intense mixing patterns; thus, the amount of slag emulsification is reduced significantly. Consequently, if the internal design of the ladle shroud is able to dissipate the kinetic energy before the fluid enters the tundish, it shall be possible to reduce considerable the slag emulsification and the slag opening area.

Aug 17, 2017