Search Documents

By David E. Nicholas, Steven R. Dismuke, Paul F. Cicchini

The Buick mine, located 195 kilometers (120 miles) southwest of St. Louis in the Viburnum Trend, is owned and operated by Homestake Mining Company. The mine produces lead and zinc ore from a room and pillar mining method at a depth of approximately 335 m (1 100 ft). The Buick orebody typically averages 60 to 120 m (200 to 400 ft) in width with ore thicknesses ranging from 2.4 to 36.6 m (8 to 120 ft). The mine is divided in two; the halves are referred to as the North mine and South mine orebodies. The North mine orebody contains the higher grade ore; however, the developed reserves for the South mine orebody comprise about 60 percent of the total developed reserves for the Buick property. Existing pillars represent one-third of the total developed reserves.

Jan 1, 1986

By C. A. Young, J. D. Miller

The surface chemistry of the calcite/oleate flotation system was examined by in-situ FT-NIR/IRS. Spectra of combination and overtone bands of aliphatic stretching vibrations revealed gauche/trans conformational changes that occurred solely as a function of temperature. The conformational changes were attributed to the simple "melting" behavior associated with phase transitions. It was concluded that chemisorbed oleate at calcite surfaces is gel-like at temperatures below 22oC, resembles a coagel between 22oC and 31oC, and becomes micelle-like at temperatures above 31oC. By comparison, chemisorbed oleate at fluorite surfaces also undergoes these phase transitions but is additionally dependent on adsorption density. The conformational changes were observed at high chemisorption densities (> 2.0x10-10 mol/cm2) and attributed to molecular forces, primarily van der Waal's interactive forces, among neighboring chemisorbed oleate molecules. Similar analysis of in-situ FT-NIR/IRS spectra of surface-precipitated calcium dioleate at calcite surfaces did not exhibit this behavior thereby confirming that surface-precipitated calcium dioleate remains in an all-trans conformation. The results help explain why surface polymerization is not observed at calcite surfaces but is observed at fluorite surfaces.

Jan 1, 2002

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By Steve Meador

West Virginia's basic coal mining regulatory programs are not unique when compared to Federally approved programs implemented by other coal producing states. In fact, the language in The West Virginia Energy Act governing subsidence mirrors that written in the Federal Surface Mining Control and Reclamation Act as well as other states' statutes. Certain legal and administrative issues, how¬ever, combine to make West Virginia's regulation of surface subsidence a singular approach.

Jan 1, 1986

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By J. F. T. Agapito

OCI Wyoming mines two flat-lying trona seams that are 3- to 3.5-m- (10- to 11.5-ft-) thick, about10 m (33 ft) apart and 250-m- (820-ft-) deep at its Big Island Mine in Wyoming. Continuous miners and a yielding-pillar system have contributed to improvements in resource recovery and productivity. The use of yield pillars minimizes the stresses transmitted from the upper to the lower seam. However, yielding must not impact the good, long-term stability needed to prevent subsidence for a large portion of the mine beneath the Green River channel.

Jan 1, 2000

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

Inn mining communities throughout the western United States, cows have always been part of the landscape as they graze on surrounding rangelands. Until recently, mining companies regarded these animals as something to be kept off their properties — especially any freshly reclaimed lands. During the last few years, though, this situation has begun to change. Today, cattle can be seen in a handful of mine settings, moving up and down the slopes of mine tailings and waste rock. These animals are being used by several companies to do some of the reclamation work once performed by large earth-moving equipment, mechanical spreaders, rippers and seed drillers. This is because cows can contour slopes more naturally and produce and spread soil nutrients in ways that tractors and ripping machines cannot.

Jan 1, 1999

By Beverly Cramp

In 1995, mining engineer Alain Gachet thought about using Earth-observation satellite imagery to search for precious minerals. The latest radar Earth-observation satellite, Canada’s RADARSAT-1, had just been successfully launched at the time, creating new opportunities for commercial applications. Gachet was working in Congo Brazzaville as an oil executive and general secretary of Elf Congo for the French national oil company Elf Aquitaine. He understood that the RADARSAT-1 launch promised new and cost-effective sources of data for mineral and oil exploration. “It was early 1996 before I ordered my firstRADARSAT-1 satellite images,” said Gachet. “I was first struck by the quantity of information delivered by the radar images. Linear structures and faults were clearly defined and subtle topographic features were tremendously enhanced,” he said. “It was ‘tree top geology,’ but this kind of information appeared to be key for finding new gold seams.”

Jan 1, 2003

By Georgios Kalamaras, Chiaia Dinu, Platania Paolo, Alessio Carlo, Giampiero Cirvegna, Claudio Santucci

The Project alignment initiates north of Pinerolo, along the State Road 23[S.S. 23] that is one of the principal arteries to the northwestern Alps where a number of Olympic events for the 2006 Winter Games will be held. The 3.5 km ring road bypasses the Porte habitat by traversing twice the Chisone River. It consists of the following principal structures [Figure 1]: San Martino bridge [130 m in four bays] Prarostino viaduct [130 m in four bays] Craviale tunnel [1055 m] Turinella bridge [a 50 m long bridge that connects the two tunnels] Turina tunnel [665 m] Malanaggio viaduct [350 m in 9 bays]. The road section is 13 m wide and is made up of two 3.75 m lanes, a hard shoulder [1.50 m wide] and a 1.25 m wide curb for each lane. The Project maximum velocity is 100 km/h.

Jan 1, 2005

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By Tad S. Golosinski, R. Larry Grayson

Online education is not new. During the last decade, it has reached the stage where many universities offer a variety of courses, degrees and programs without any associated residency requirements. The most successful of the online universities, University of Phoenix, offers hundreds of accredited programs for close to 100,000 students throughout the world (www.phoenix.edu). Online education is considered to be a valid equivalent to traditional, classroom-based education. It is best suited to the needs of mature students with full-time jobs and a desire to deepen their knowledge. While most of the e-business has experienced severe setbacks during the last two years, e-education shows no signs of slowing down. On the contrary, the number of students and institutions offering online education keeps growing. The value of e-education associated expenditures was expected to reach $300 billion in 2001 (Sanoff,2001), making it a serious and mature industry.

Jan 1, 2002

By S. Christiansen, G. R. Winslow, R. W. Kobler

Todays End of Life vehicles are shredded and their metal components recovered and recycled by standard methods. The remaining non-metallic fraction is shredder residue, and contains vast amounts of high value engineering plastics. None are today recovered. Discussed are the developmental approaches used in the first process to recover these valuable plastics. Examined are initial laboratory studies, pilot plant design and construction, product development, results, and flowchart explanations.

Jan 1, 2001

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002

By Z. J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multi-disciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4850 ft) and 2.25 km (7400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program including: preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in-situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations were followed by geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001