Search Documents

By Aloke Verma, R. Singh, S. Jana, C. Sawmliana, P. Pal Roy

On July 21, 2004, a trial blast using electronic detonators was conducted in India for the first time in an opencast mine at Pundi-E Quarry of TISCO, West Bokaro. Orica-IEL conducted the test using electronic detonators. To provide necessary technical feedback on wider applicability, CMRI scientists also participated in the trial blast.

Jan 1, 2006

By Mike Higgins

"Data management is emerging as a major concern for miners. Engineers today are faced with anextensive array of data from varying sources, and are required to consolidate and analyse thisinformation to produce an effective and efficient mine plan. The viability of a mining operation canbe dependent on the outcomes of this process. With so much at stake, it is no surprise that mostengineers prefer a standard approach to blasting which is designed to minimise risk rather thanoptimise performance."

Jan 1, 1998

By Deepak Vidyarthi

This paper deals with various measures adopted in protecting a conveyor duct (named after a Conveyor Belt that was numbered as ‘02’) housing a 1600 mm (63 inches) belt conveyor system in a large, heavily mechanized open cast iron ore mine, producing about 20.0 million tones of ore per annum.

Jan 1, 2008

By Ajoy K. Singh, B Mohanty, P K. Singh

A study was conducted to investigate the damage potential to underground multiseam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with much higher amplitudes compared to those in pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or higher. The vibration magnitude recorded was higher in upper-seam openings than in belowseam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle velocity-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for the safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.

Jan 1, 2011

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015

By Dave Kay, Young-Suk Song

To meet the needs of South Korea's rapidly expanding economy, a large number of infrastructure projects are under way to improve transportation efficiency within the nation. These projects include high-speed rail links between major population centres and improvements to the road network. Being densely populated and geographically mountainous, infrastructure development in Korea requires a significant amount of tunnelling. Owing to the predominantly hard granitic nature of rock, drill and blast is the preferred method of tunnel advance. The Korean tunneller, however, faces the same pressures as those of his international counterpart in that both cost and production targets need to be achieved while meeting expectations of both community and regulator.

Jan 1, 2005

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By Randall Wheeler, R. Frank Chiappetta

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation. and Explosives Applications - Orlando, Florida, USA July 24 - 27,200O 2000 BAI - PROTECTION AGAINST LITIGATION WITH GOOD PRE-BLAST SURVEYS, DAMAGE INSPECTIONS AND RECORD KEEPING 1 of 65 Good Record Keeping is Essential for: 1 ) Compliance with any prevailing Local, State or Federal Regulations, ordinances and permits. 2 ) Protection against potential litigation. 3 ) Balancing explosive consumption, use & costs. 4 ) Use in blast designs.5 ) Blast diagnostics & troubleshooting good/bad shots.

Jan 1, 2000

By Derek T. Novotny

Blasting cap precision is of major importance to advanced blast design. New technologies have introduced the use of microchips within detonator casings in the hope that the electronic control of the timing element will increase the accuracy of the cap and therefore improve the results of perimeter control blasting applications. The electronic detonators have proven to be accurate in timing tests done to date. They boast cap scatter results to microsecond accuracy, but the question is, does this degree of accuracy actually prove to be beneficial during practical use in the industry, or are conventional technologies applicable.

Jan 1, 1998

By Jackson R. Pressley, Bruce Vandenberg

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1992

By R. Raghavaraju

Estimation of the dynamic stress field in terms of its amplitude and decay around a blast hole is a key input parameter in all numerical modeling and blast prediction exercises. However, there is very limited information available in literature on these critical parameters, which would be considered essential in any blast modeling exercise. A laboratory-scale experimental study has been carried out in two different rock types to study at very close range the stress wave decay from a blast hole at distances ranging from 3 to 10 borehole radii. The single–hole blasting experiments employed a centrally located detonating cord (5.3 g/m) in 6 mm(1/4 inch) and 10 mm (3/8 inch) boreholes. The coupling medium employed was air and water, in addition to using a thin-walled copper tube in intimate contact with borehole wall to prevent of penetration of explosion gases into the emerging cracks. The paper describes the nature (amplitude and decay) of the transmitted shock pressure and their evolution in the two rock types for these various experimental conditions, which are present to varying degrees in all blasting operations.

Jan 1, 2014

By Zou Dingxiang

Rock blasting in the project of “Site Formation and Associated Infrastructure Works at Choi Wan Road and Jordan Valley” is the largest urban blasting project in the history of Hong Kong and also is rare in the world. More than 6.2 million of in-situ rock has to be excavated by blasting. The site is located in the center area of eastern Kowloon peninsula, surrounded by highways, registered cut slopes, high-rise residential buildings, MTR subways and the public utilities. The complex situations bring great difficulties and risks to the blasting works. A bird-view photo of the site is shown on Picture 1.

Jan 1, 2007

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By Paul Worsey, Seokbin Lim

There are two major types of shaped charges, conical and linear (Ref 1, 2). Conical shaped charges are used to perforate targets and are mainly used by the military as anti armor weapons and by the oil industry for oil well perforation. In contrast, linear shaped charges are primarily used to cut metal in the demolition industry with other uses including separating devices in the space industry. There is a large amount of material published on conical shaped charges because of the high level of defense industry research and funding, however in stark contrast there is very little published on linear shaped charges.

Jan 1, 2003

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By Patrice Favreau, R. F. Ph. D. Professor Emeritus Favreau

After Nobel invented dynamite, blasts were carried out by trial and error, without the use of equations based on the fundamental principles of Chemistry and Physics, although everyone accepted that shock waves were involved; but no equations were available to calculate their intensity. Around 1950 however, M.A. Cook proposed a procedure to calculate the thermochemistry of an explosive, and thus evaluate theenergy released during the explosion of a fully confined explosive. Some blasters then began to use theEnergy Factor; the latter, however, does not subdivide the energy into its three kinds of activities necessaryfor a successful blast, as demonstrated in 1968 by reference 2, namely i) the shock wave which weakensthe rock; ii) the stress field SS which fully fragments the rock; and iii) the release of the stress SS whichcauses the fully fragmented rock to burst out with the velocity necessary to move the rock into the muckpile. The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999