Search Documents

By M. Tominaga

An industrial port complex was constructed on the west coast of Leyte Island The work was started in December 1981 and completed in May 1984. This port complex includes a 665 m long wharf and can accommodate vessels ranging from a 60,000 DWT ore carrier to a 4 000 DWT general cargo ship. It now handles materials for and products from a copper smelter with an annual capacity of 130,000 t and a fertilizer plant with an annual capacity of 900,000 t. The Wharf structures consist mainly of interlocked steel pipe piles, steel sheet piles and steel pipe Piles. Material handling equipment such as unloaders, shiploaders, etc. were installed on the wharf. Site survey, planning, engineering design and construction aspects of the port development are discussed in this paper with particular emphasis on the wharf structure.

Jan 1, 2010

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By James J. Neate

The augered cast-in-place pile system came into use in the late 1940's where various techniques were tried using pressure grouting methods. In the early development stages some piles were installed using the preplaced aggregate concrete system. As development continued it became more apparent that placement of coarse aggregate was more costly than making a pile out of a cement and sand mixture only. Various techniques were tried consisting of pumping structural grout into an open hole through a pipe left in the bottom of the hole, drilling or driving a pipe in close proximity to the tip elevation of the auger or in working a pipe down adjacent to the auger fluting. For these techniques the pipe was usually withdrawn after grout appeared at the surface. In 1951 a patent was applied for by Raymond Patterson describing the above techniques along with a technique for placement of grout using a hollow stem auger and a removable plug or lead bit at the tip of the auger. The plug or lead bit was removed by grout pressure and this would be an expendable item for each pile placed. The patent was granted in 1956 and patent rights were assigned to Intrusion-Prepakt, Inc. Shortly thereafter other contractors were granted licenses to utilize the system. Patent coverage expired in 1973 and this method now is in the public domain. Today the method is in wide use throughout the world and is particularly well accepted in Japan and England.

Jan 1, 1988

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By Giovanni A. Bonita

The United States Capitol Visitor Center (USCVC) is one of the largest underground structures ever constructed in the Washington, DC, metropolitan area. The 600,000 ft2 (55,750 m2) structure is entirely underground and immediately adjacent to the shallow foundations of the existing U.S. Capitol building. Interior building columns for the USCVC were supported on 186 drilled shafts that varied in diameter from 4 to 9 ft (1.2 to 2.9 m) and in length from 15 to 45 ft (4.6 to 13.7 m). The vast majority of the building utilities were located beneath the basement floor slab. It was decided at the onset of the project to proceed with construction prior to completion of the design drawings, and coordination between the underslab utilities and the drilled shafts had not yet been finalized at the onset of drilled shaft installation. Given depth and location restrictions of the outlets, relocation of the bulk of the utilities was not possible. Almost half of the drilled shafts were affected, leaving redesign as the most feasible remedial solution. The redesign involved adjustments to the shaft length, diameter, and bell. It took place on a case-by-case basis, sometimes only minutes before installation began. Coordination between the field and design team was excellent, and delay associated with the redesign efforts was minimal. In addition, the detailed, high-quality field records kept by both the contractor and field engineers allowed for accurate and fair estimations of the added drilled footage and concrete volumes placed. The additional service fee, which was minimal, was settled quick and fair.

Jan 1, 2006

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

By M. T. Davisson

Pile compression load capacity prediction methods are divided into four categories for purposes of discussing their reliability compared to static load test results. The categories considered are: 1) static analysis, 2) driving formulas, 3) wave equation analysis, and 4) dynamic measurement and analysis. It is concluded that any method of static analysis that works for the geological deposit in question may be satisfactory. However, any given method can be quite wrong when applied to other deposits of soil that are different in terms of their engineering and geological characteristics. Dynamic formulas are found to be theoretically unjustifiable. The ready availability of the wave equation analysis for microcomputers eliminates the need to utilize dynamic formulas. The wave equation analysis is found to be the best analytical method for making predictions both for design and for construction control. Dynamic methods of measurement and analysis are found useful, but have limitations that have caused troubles on many projects. Two case histories are presented that show the limitations of dynamic measurement and analysis, and of the wave equation analysis. Soil deposits exist that defeat both the wave equation and dynamic measurement techniques; static load tests are currently the only method of proving the load capacity of piles in such soils.

Jan 1, 1991

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Onur Kacar

A numerical approach has been implemented to assess the settlements of pile groups bearing in clay. A three-dimensional finite element program has been utilized to model a vertically loaded spread footing, a single pile and a pile group. The soil-pile interaction was modeled with elastoplastic soil and interface elements. The model has been calibrated using a full scale load test results of the spread footing. The load transfer between the pile cap and the piles was assessed and compared with the measured load transfer. The predicted settlements for the pile group were compared with the settlements measured in the load test. Two analytical methods were adopted to predict the pile group settlements and they were compared with the measured values. The group effect determined from the analysis and load tests was compared with the interaction factor approach. It was shown that three-dimensional finite element approach can be successfully utilized to assess the soil-structure interaction and hence the load transfer between the piles and pile cap. Also, it was shown that the interaction factors method and equivalent footing method work well in the working stress range, however they underpredict the settlements at larger loads. INTRODUCTION The settlement and stress distribution of pile groups have been traditionally estimated based on load test results of single piles and accounting for the group effect using various approaches. The most widely used approaches are group interaction factor method, equivalent footing method and equivalent pier method. These approximate solutions are used very commonly in practice as full-scale load tests on pile groups are very expensive and time consuming. These approximate solutions are also adopted in design guidelines such as AASHTO LRFD Bridge Design Guidelines (2014) and FHWA Design and Construction of Driven Pile Foundations (2016). In this paper, a full-scale foundation load tests performed by Nagai et al. (1961) and reported by Koizumi and Ito (1967) is modelled using a three-dimensional numerical method. The settlements and the stress distribution on foundations were then compared with the traditional equivalent footing method and interaction factor methods.

Jan 1, 2018

By J. C. W. M. de Wit

An excavation, within which a tunnel is sunk as a part of the Centraal Station underground station (platform section) of the Noord/Zuidlijn ('North/South Line'), is to be created beneath the Amsterdam Centraal ('Amsterdam Central') station. The section beneath Amsterdam Centraal Station is characterised by the application of a particular technology in the form of, inter alia, the so-called 'sandwich wall'. This is a composite wall consisting of two rows of Tubex piles with a body of jetgrout columns in-between. This wall acts both as an excavation support wall and also provides vertical bearing. The installation of the wall, including both Tubex piles and jetgrout columns, within these specific conditions (limited height, sensitive historical building), within the design requirements set in terms of construction tolerance and water and soil retention, may be regarded as being a pioneering achievement. The environmental constraints are that the trains should continue to run, the inconvenience to passengers should be kept to a minimum and the historic station should not suffer any damage. Because of the complexity of the working conditions, the project is being overseen by a steering group of experts in the specified construction processes. In order to manage the project risks, jet grouting trials were initially carried out, in order to highlight and control execution problems; the practicability of the design is then tested. Work commenced on the sandwich wall in 2003, when the wooden piles were extracted at the locations where the sandwich wall was to be constructed; in 2004, the steel Tubex piles for the southern wall sections were installed. From May 2005, the construction of the sandwich wall got under way; in addition to the described process supervision, an extensive measuring programme was established, so that the process could be adjusted as necessary and the quality of the finished product determined. This applied to both individual columns and for the end product, the sandwich wall. The measurement results were processed for each column, interpreted and the effect on the work still to be conducted was assessed for each future column. Preventative and corrective measures were, if necessary, taken in order to control or counteract the measured defect. In addition to the process-oriented and qualitative measurements, various independent measurement systems at the station building served as a further control in order to prevent damage to the building.

Jan 1, 2006

By Steven L. Anderson

A cut-off wall has been designed and is currently under construction along the Back Dam of the existing tailings impoundment at Red Dog Mine, Alaska. The cut-off wall, which will be in the order of 5,000 ft long and up to 150 ft deep, when complete, is being excavated using a 40 metric ton Bauer trench cutter head mounted on a Liebherr crawler crane, in combination with a closed loop slurry pumping and de-sanding system. The tailings impoundment is situated in an area of warm permafrost and high potential seismic activity. Design incorporated an assessment of rock jointing to define the final depth of the wall along the alignment requiring the use of plastic concrete backfill to address the concerns associated with potential cracking of the wall due to settlement and during seismic activity. The results of the geotechnical investigation program, particularly with respect to variation in rock hardness along the wall alignment are discussed, as are the design criteria for the plastic concrete backfill, the challenges faced during construction, including scheduling of the work with the on-going dam raise activities of the mine, and the lessons learned with respect to potential productivities and selection of cutter wheels and teeth. Also described are the requirements for and advantages of utilizing a slurry boosting system to meet pumping requirements, re-design of the plastic concrete mix to consider workability and optimization of cutter teeth configurations to reduce wear through highly varied rock hardness.

Jan 1, 2010

By David Winter

The geotechnical design, construction, and monitoring aspects of a tied back excavation 85 feet deep in Seattle, Washington are presented. The excavation was completed in overconsolidated deposits of sand, silt, and clay. Lateral soil pressures used in shoring wall design were the lowest to date for an excavation of this size in Seattle. Instrumentation data collected from hydraulic load cells and inclinometers were analyzed and are discussed. The data suggest the actual soil pressures felt by the wall were lower than the design values. Recommendations for future study, as well as future design modifications are given.

Jan 1, 1987

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By Nikolaus Schneider

"Abstract: The combination of failure in joints of diaphragm walls and their exposure to water pressure may have far reaching effects ranging from water leakage to the risk of catastrophic loss of stability for the retaining wall and civil structures behind it. Investigations of imperfect joints in diaphragm walls have led to the development and testing of a quality tool to monitor the joint integrity of diaphragm walls during construction. By applying independent mechanical sensors (“joint inspector”) to the steel frame of hydraulic or mechanical grabs, it is now possible to record the surface conditions of exposed primary joints during the construction of secondary panels. This allows for the implementation of corrective action during the construction process should joint quality not indicate a watertight connection to the adjacent panel. The joint inspector, used for different types of stop ends, was tested on a full scale test field at several construction sites. The implementation of this new quality tool drives a new quality standard for deep excavations in inner city areas.General introduction to diaphragm wallsDiaphragm walls are reinforced concrete elements constructed using bentonite slurry to temporarily support an open trench in the ground. They are used in two main fields of application in civil construction, as foundation elements for vertical and horizontal loads (barrettes) and as retaining walls for excavation pits.Particularly for deep excavation pits in inner city areas, diaphragm walls are used as temporary or permanent walls of retaining walls. Alternative retaining wall systems would be secant pile walls, sheet piles or soldier piles, but these have disadvantages in structural strength when compared to diaphragm walls. If the vertical load of existing buildings next to the excavation pit has to be accommodated, the most practical solution can be found using diaphragm walls supported by prestressed anchors, steel struts or slabs."

Jan 1, 2014

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018