Search Documents

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Interest in those physical properties of minerals which might be used to good effect in prospecting is not new. Early in the nineteenth century attempts were made in th'e Cornish mines to measure the natural electric potentials set up by chemical changes proceeding in the lodes. The distortion of the earth's magnetic field by bodies of strongly magnetic iron ore received early recognition in Sweden. Treasure-finders, working on the principle of electrical induction, appear to have been invented about eighty years ago, though were probably not then applied to mineral exploration. By the end of the nineteenth century Eotvos, a Hungarian physicist, had constructed a highly sensitive type of torsion balance capable of measuring the minute distortions in the earth's field of gravitation resulting from variations in the density of the materials composing the crust. During the first decade of this century he demonstrated its value in tracing rock-salt deposits in virtue of their low density compared with the surrounding rocks. Geophysical prospecting began to be recognised as having a very definite value and its development gathered momentum. Its great expansion took place after the 1914-18 war, when its value in oil exploration was amply demonstrated, and this expansion has continued to the present time and shows no signs of abating.Divisions of Applied Geophysics.The four main divisions of applied geophysics are electrical, magnetic gravitational and seismic. With the importance of ores of radio-active metals, one might add to these a radio-active division. The first two are more important to the field of mining, but techniques based on gravitational attraction have their uses in particular cases. Seismic methods are not generally suited to the exploration of metallic ores, but have proved of enormous value in the search for petroleum. With vast quantities of oil as the prize, more money has been lavished on the deve10pment and practice of these methods than on all the others put together.Geophysical Prospecting Methods.Geophysical prospecting methods may be used to detect a mineral deposit directly in virtue of differences in the intensity of some physical attribute common to it and the enclosing country rock. Examples of this are the detection of rock-salt by gravity measurements, or of iron ore by magnetic methods. Of much wider application, however, is the indireot approach in which the aim is to determine, by geophysical means, the geological structures controlling the disposition of mineral deposits. These structures may be partly known from geological work, in which case geophysical methods are useful adjuncts. Where, because of an 'unbroken cover of overburden, no useful geological information presents itself, scout drilling or geophysical prospecting are the only alternatives. Overburden is here intended to mean any covering material not, involved in the structures controlling the mineral deposits. Prospecting for petroleum amounts to the detecting of favourable reservoir structures, and as the chief types of such are the same the world over...

Jan 1, 1950

As in other countries, gold mining inNew Zealand has been cyclic in character. Looking at these cycles may provide insights as to what may occur in the future and that is the basis for this study.   New Zealand has experienced four gold mining cycles. The first began in 1857, peaked in 1866 and terminated in 1890. This cycle was characterised by alluvial gold mining by individuals and small groups. This is referred to as the Labour Led cycle. The second cycle began in 1890 and reached its peak in 1906 and terminated in 1929. This cycle was characterised by the use of dredges in alluvial gold mining and was also the peak of hard rock mining. This cycle is referred to as the Technology Led Cycle. The third cycle peaked in 1940. This cycle was far less significant than the previous cycles, arising out of the depression when the unemployed embarked on small scale alluvial mining. This overprinted the continuing decline that occurred after 1906. This cycle is here referred to as the Depression Overprint Cycle.   The fourth cycle began in 1984 when production began to climb rapidly from a very low base. The growth in production was spurred by rising gold prices in the early 1980s resulting in relatively low grade gold-bearing alluvial ground becoming economic. But in the 1990s, production from the new hardrock mines in Coromandel and Otago has overshadowed alluvial production. This cycle is here referred to as the Price Led cycle.   What are the future prospects for gold in New Zealand? Although there are many factors involved, this will be largely determined by two factors; firstly, continued access to prospective gold-bearing properties, and secondly, the price of gold. Based on these factors, three future industry scenarios have been developed. The first of these is industry collapse, in which access to prospective property is constrained and prices mayor may not weaken. The second is industry consolidation, in which the available ground is accumulated by a small number of large companies who can use economies of scale to weather price fluctuations. The third scenario is industry growth, in which access to prospective ground is constrained in environmentally sensitive areas but is otherwise relatively unconstrained. Efficient companies are allowed to work in a policy and economic framework that allows them to make a major contribution to the economy.   While the industry cannot control these critical factors, a good knowledge of the positive role gold mining could play in the future economy may provide a framework by which the access issue, in particular, may be addressed from a balanced perspective.

Jan 1, 1994

Much attention in controlling blast vibrations has been centred on the probability of causing damage to structures in the area adjacent to where blasting is carried out. In most cases these structures are residential properties and the effect of the vibrations on the occupiers has not been studied to any great extent. This paper looks at the sources of disturbance caused by blasting and their psychological effect. A comparison of ground vibration levels for compliance is examined within the framework of structural and human response.

Jan 1, 1998

By A D. Campbell, G R. Power

Many caving mines use numerical flow models to simulate mine production, forecast recovered ore grades and optimise the draw strategy. In sublevel caving (SLC) mines, the effects of blasting and fragmentation at an individual ring scale generally cannot be included in these models. Previous attempts to use results from marker recovery trials to calibrate numerical flow models have been limited due to difficulties in accounting for blasting effects at a ring scale. This paper outlines how an empirical criterion for blasting and fragmentation was used to attribute variable flow properties into a numerical flow model based on the blast design and modelled fragmentation. The flow model was then validated using data from a number of full scale marker recovery experiments. The result of this approach was a significant improvement in forecast accuracy when compared against the same modelled cave marker recovery without the inclusion of these blasting effects. Improvements in the flow model are currently being adopted within the mine scale model to further improve the accuracy of grade forecasting, optimise the draw strategy and increase net present value. The integrated modelling approach is also being used to simulate the effects of different drill and blast designs on cave recovery. It is suggested that, if implemented, the technique would lead to improved blast designs in other SLC mines, increase the value of marker trial data and reduce costs associated with large scale blast design trials.CITATION:Campbell, A D and Power, G R, 2017. Improving calibration of flow models against SLC marker trials by linking blasting effects to particle mobility, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 11–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D Garcés, M Meléndez, R Castro, E Viera

Enhancing the understanding of gravity flow in caving operations is a key factor in the design, operation and success of caving methods. Consequently, much research has been performed to increase knowledge about gravity flow. Many valuable theories have been gained from different research approaches, which include physical modelling, numerical modelling and a limited number of full-scale tests. Recent advances in technology have allowed Codelco Chile to carry out trials using Smart Markers technology. This technology was used in Esmeralda mine’s Block-2 at El Teniente mine from August 2012 to January 2015. This paper aims to determine the characteristics of the extraction zone and obtain the data that will allow greater understanding of gravity flow for design and draw control purposes.The collected data from recovered markers were analysed using a linear interpolation of both the initial position of the markers and drawbell accumulated drawn tonnage. For each drawpoint in the trial, the regularity or irregularity of flow was analysed based on the recovered markers and the drawn tonnage. Correspondingly, the relationship between flow characteristics and observed fragmentation in drawpoints was analysed. The gravity flow of the Smart Markers revealed that current drawpoint spacing provides the interaction conditions of adjacent flow zones. However, it is possible to increase the drawpoint spacing while allowing caved rock to be extracted from the major and minor apexes.The results of this research also verified that full-scale test data are the predominant factor in the production level design and production control at El Teniente mine.CITATION:Garcés, D, Viera, E, Castro, R and Meléndez, M, 2016. Gravity flow full-scale tests at Esmeralda Mine’s Block-2, El Teniente, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S Lush, R Polglase

McConnell Dowell is pleased to be given the opportunity to present two papers to this conference. The first is a general discussion paper on our work in the field of slurry transportation. The second will be a technical paper on the development of a welded coupling compatible with urethane lined pipework. We trust that by discussing our recent work we can leave two lasting impressions on you: the versatility and useful role of slurry transportation, and the leading role taken by New Zealand in this technology This paper discusses three recent projects the New Zealand Steel Ironsand Transfer Line the Coarse Coal Ship Loading Technology the Nerang River Sand By-pass System. These have followed on from the other slurry projects with which McConnell Dowell has been associated such as the ironsand export trade at Waipipi and Taharoa. The New Zealand Contractors Federation awarded the Construction Award for 1986 to McConnell Dowell for the Ironsand Slurry Pipeline.

Jan 1, 1986

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

By P R. Denize, V S. Wein

A brief review of the Waipipi Iron Sands Limited company history and operations over the past ten years is made along with a summary of the benefits of this mining company to New Zealand. Land rehabilitation procedures in coastal dune lands are described in detail and brief mention is made of a study of animal health and copper uptake. The paper concludes with a summary of the increased emphasis on agronomy and restoration as the mining operation commences dredging in a better class of grazing land.

Jan 1, 1981

By Woodcock J. T

During the dissolution of gold in fully aerated cyanide solutions the CN ion is the active agent, and consequently the usual method of evaluating the dissolving power of such solutions is to determine the CN- concentration analytically. The presence in the solutions of copper and/or zinc which themselves form complex cyanides, may result in erroneous conclusions as to the free cyanide ion concentration determined by titration.In this paper the theory of titration of such solutions has been developed, and potentiometric methods have been used to follow the behaviour of complex cyanides of copper and zinc. The results for cuprocyanides show Cu (CN)s to be the most important copper complex, and in addition they explain the reported low rates of solution of gold in copperbearing solutions which when titrated in the usual way, appear to have adequate free cyanide. An explanation of the misleading value of the titration is given, and suggestions for recognition of the condition are offered. Preliminary results for zinc-bearing solutions show that there is no satisfactory end-point for the titration of CN- in excess of that in the complex Zn (CN) 4=, which dissociates to CN and Zn(CN)g-.

Jan 1, 1950

By E Breese

The Grey River dredge is the first large scale alluvial operation to be permitted under the Mining Act 1971 and the Water and Soil Conservation Act 1967. The experience of Grey River Gold MiningLimited in pursuing these statutory approvals has identified weaknesses and strengths in the present system and problems which need to be resolved. The Company has learnt lessons, which if heeded, will assist future large scale alluvial mining projects.

Jan 1, 1989

ABSTRACTOperations Research and associated techniques have wide application in the Mining Industry and have been used in Mount Isa since 1961.Typical of the projects undertaken by the OperatIons Research staff are1. the development of a complex computer programme for use in economic evaluation of mineral deposits,2. development of a production scheduling and control system for a complex mining operation,3. SImulatIon of a metallurgical plant operation to test the adequacy of design specifications and4. analysis of vehicular accident data to valuate alternative courses of insurance action.

Jan 1, 1968

By P Williams, S Flynn, R Birchfield, R Simcock, R Toft, P Comeskey

Direct transfer, or community translocation, comprises salvage and replacement of intact æsodsÆ of vegetation together with underlying soil. It has been applied to New Zealand mine sites restoration of native grasslands, wetlands, scrub lands, and forest. It is an equivalent technique to æinstant lawn or tree gardenÆ, commonly used in urban landscaping. Two to six m2 scoops of vegetation, with up to 0.7 m of soil attached, and including root plates of trees and shrubs, are relocated from stripped areas ahead of mining to sites prepared for restoration. Direct transfer uses hydraulic excavators or face shovels and dump trucks, possibly with the aid of bulldozers and other earthmoving machinery. The main advantages of direct transfer, compared with sowing or planting systems for mine site restoration, are the recycling of plant and soil materials which were often wasted by burying under overburden materials, a significantly faster revegetation process, and restoration of the whole ecosystem (plants, animals, birds, invertebrates, and microbes). The main disadvantages are higher costs of stripping and dumping, a greater degree of machine operator skill required, and scheduling becomes critically important. To illustrate the key principles, this paper gives examples of successes and failures of the technique for a variety of New Zealand mining situations. Direct transfer has been successful for a range of communities, from fern wetland and sub-alpine tussock grasslands to 5 m-tall beech forest under storey and seral shrub land, and from temperate to sub-alpine climates. Successful examples show both rapid recovery of indigenous vegetative cover and conservation of habitat for birds and invertebrates. Failures have resulted from excessive death of plants because of inadequate soil salvage depths, acidic leachates, inappropriate handling of stripped sods by inexperienced machinery operators, or prolonged drought conditions immediately following relocation. Change in plant species composition has occurred where clumps of vegetation are too far apart, or shifted plants were too small - in both cases invasive weeds have smothered the original vegetation. Changes in hydrology can also have significant impacts. Our experience indicates that the advantages of direct transfer far outweigh the disadvantages and is now used as the preferred restoration method, where practicable, at mines where it has been trialled.

Jan 1, 2000

The following observations on the mineral composition of the lead-zinc ores at Captain's Flat, New South Wales, are based upon the examination of a collection of specimens made during a brief visit to the mine in January, 1942, in conjunction with earlier studies of specimens and mill products, which have 'been the subject of various Mineragraphic Reports, Captain's Flat is about 35 miles south of Canberra, and is connected with the main line from Goulburn to Bombala by a branch line to Bungendore, 23 miles away from the mine.The geology of the mine has been described by Kenny and Mulholland2 and by Harper.3 The country consists of Silurian sediments, which have been invaded by a composite sill of quartz-felspar-porphyry. Both sediments and sill have been folded gently, the axial lines of the folds trending north and south. In the vicinity of the orebodies the folds are steeper, and thru,st faults are associated with the anticlines. The intense compression and shearing that accompanied the faulting has converted the adjacent porphyry to schist. The Captain's Flat orebodies occur along such a zone of shearing and faulting, on the eastern limb of a steep, north-pitching anticline. At their southern end the orebodies are enclosed in the slates underlying the porphyry, but the northerly pitch of the fold carries the slate to greater depth in the northern part of the mine, where the orebody lies beween schistose porphyry on the hanging wall and massive porphyry in the footwall.THE OREBODIESThe orebodies occur along a N.-S. strike length of 4,200 ft., and from the point of view of mining, fall into three sections: the Elliot's Section to the north, the Central Section, and the Keating's Section to the south. The Keating's Section is separated from the Central Section by 500-600 ft. of mineralised ground of so low a grade as' to be called barren, and is offset about 125 ft. to the 'east of the Central body by an oblique fault striking N.300E. Elliot's Section and the Central Section are connected by persistent veins and stringers of lead-zinc ore, but although these are...

Jan 1, 1943

This article attempts to outline essential features of the Mount Isa ore deposit, to reveal the agencies thought to be responsible for its localization, and to describe methods used for obtaining and applying geological data on a commercial basis. Structural features are emphasized because they have proved the most useful agencies to date in searching for ore. Vertical depth, horizontal width and stratigraphic thickness are used throughout the article, and quantities are quoted in long tons.THE DEPOSITA width of more than two miles of evenly bedded shale of the Mount Isa series (upper pre-Cambrian) lies sandwiched conformably between quartzites. The series strikes N.S. and dips approximately 60° W. Shale is unaltered...Important geological work has been carried out by the Queensland Geological Survey, chiefly by Mr. S. R. L. Shepherd, in co-operation with the Geological Department of Mount Isa Mines Limited. Selected references are The Queensland Government Mining Journal for December, 1931, January, 1932 (Rio Grande Lode); December, 19B2 (Black Rock Lode); October, 1933 (General structure); October, 1936 (Mount Isa Lode).

Jan 1, 1939

Performance of Dry Separation Processes in Cenospheres Recovery from Coal Fly Ash

Sep 13, 2010

Automation in underground mining enhances safety and leads to economic efficiency. In the past many efforts have been made on the automation of longwall shearer operation. With respect to the ultimate goal of automation, ie self controlled operation, coal bed boundary detection is one of the key problems. For longwall human labor is necessary in order to detect the exact position of the coal seam to be excavated. The authors present a sensor concept based on infrared technology and pattern recognition which will solve this problem. The very harsh underground conditions set high demands on the implemented sensors. The combination of infrared sensors and powerful processing algorithms is part of the innovative concept for automation of the new Eickhoff Bergbautechnik GmbH SL 750 shearer loader. The multi-sensor automation system EiControlPlus which is designed for the complete detection of the machine environment fills in the gap in the coal-excavation automation by building a recognition system that turns the shearer loader into an 'intelligent machine' which is capable of detecting the correct position of the seam to be excavated and thus enables human-free coal mining.

Dec 6, 2010

By Mwaba CC

Ok Tedi Mining Ltd has been using flotation for the production of copper/gold concentrates from a complex copper sulphide ore for several years. During this period, much effort has been devoted to metall- urgical treatment of the ore. This paper examines some of the mineralogical aspects of the sulphide minerals in the ore using the electron microprobe analyser. Results have revealed the complexity of the copper sulphide minerals and in particular, chalcocite. Analysis of both plant and laboratory flotation products has provided further insight into the effects of mineralogy on the flotation of copper and iron sulphides. A significant observation is that some of the pyrite minerals apparently exhibit natural floatability. The implications of the mineralogical characteristics of the sulphide minerals on the flotation of the ore are also discussed.

Jan 1, 1991

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017