Search Documents

The Reefton Goldfield on the West Coast of the South Island of New Zealand was a significant gold producing area between 1860 and 1951. During this period it produced approximately 2.1 million ounces (67 tonnes) of gold. The largest single producer on the goldfield and the deepest mine in New Zealand, was the Blackwater Mine at Waiuta which produced 21 tonnes of gold. The Prolubition Shaft reached a depth of 878 metres (317 metres below sea level). The mine closed suddenly in 1951 with about 66 000 tonnes of are remaining in the stapes. Since closure there has been no attempt to determine the ore potential of the mine at depth. This paper summarises the geology, history and resource potential of the mine and sets out two options for evaluating the remaining resource. The options are either deep drilling from surface or recovery of the Prohibition Shaft and underground development and drilling. A schedule for each option is presented and discussed.

Jan 1, 1992

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

This study of the tin-tungsten ore of the Shepherd and Murphy Mine, in central northern Tasmania, was originally undertaken at the request of the Moina Tungsten-Tin Mining Co., N.L., as part of the research programme of the Mineragraphic Investigations Section of the C.S.I.R.O. It is based on the examination of a suite of specimens supplied by the management, supplemented by a more extensive collection and observations made by the author during a short visit to the mine in October, 1956.The Shepherd and Murphy Mine is at Moina, 36 miles S.W. of Devonport and 22 miles from Sheffield, the nearest railway station. It was worked almost· continuously from 1893 to 1919, when a fire destroyed the mill; to that date it had produced concentrates to the value of £141,000. After a long period of idleness, the mine was re-opened by the present company, but it has been announced recently that unfavourable market conditions have again forced closure.GENERAL GEOLOGYThe mine is on a deeply dissected plateau, about 2,500 ft. above sea level; it lies between the Iris and the Forth Rivers, whose valleys are deep gorges cut to about 400 to 600 ft. above sea level. From Moina westwards to the Iris River, a limestone regarded as part of the Gordon River Group, of Ordovician age, conformably overlies a sandstone containing tubicolar casts which are circular in cross section, half an inch in diameter and up to two feet long, and which resemble marine worm burrows (Elliston, 1953).

Jan 1, 1958

By Edwards A. B

The following note on the mineral association in the ores of the Tennant Creek Goldfield, Northern Territory, is largely based on Mineragraphic Reports Nos. 49, 89, 117 and 193 of the Council for Scientific and Industrial Research. These reports are the results of the examinations of auriferous specimens from a number of mines of the goldfield and are now supplemented by the examination of further specimens from Mt. Samuel forwarded by Mr. V. G. Martin.The Tennant Creek Goldfield lies in the central portion of the Northern Territory, about Lat. 190 35', Long. 1340 15', on the Overland Telegraph Line and about 369 miles north of Alice Springs. It comprise an area extending about 50 miles east and west, by 30 miles north and south.The geology of the goldfield has been described by Woolnough. (2)The rocks of the area are of pre-Cambrian age, and consist of talcose, chloritic, micaceous and siliceous schists of sedimentary origin, interbedded with flows or dykes of schistose quartz porphyry, and of granites which were intruded subsequent to the regional metarporphism of the area. The rocks are moderately folded, but the beclding tends to be obscured by a pronounced east-west cleavage. The most continuous orebodies run east and west, parallel with this cleavage.Numerous lenses of hematite occur in the schists, with their long axes, parallel to the cleavage, and the gold values of the field are frequently associated with such hematite bodies. The dimensions of these hematite bodies are variable but rarely exceed a length of 300 ft., with an average thickness between 10 and 30 ft.; the original vertical dimensions are thought to be comparable with their length. The lenses tend to occur in groups when they are arranged en echelon both horizontally and in depth; and erosion has exposed individual lenses to different degrees, ranging from incipient exposure to complete removal. The existence of unexposed hematite lenses at depth has been proved by geophysical surveys, coupled with drilling tests. (3)A few of the bodies are pipe-like. Many are surrounded by a casing of brecciated rock, composed of fragments of hematite and shattered country rock, and presumably caused by subsequent earth movements which crushed the country rock against the resistant hematite bodies. In the early days of the field most of the important gold occurences were found within these crushed zones, or, to a less extent, within the hematite bodies themselves.These occurrences appeared to be associated only with those hematite lenses which were intersected by quartz veins or other lines of weakness, of later origin than the crushing. This led Woolnough to think that the introduction of the gold and attendant bismuth was subsequent to the...

Jan 1, 1942

A general outline of the significant features in the quality and manufacture of the more common refractories is given. Where possible, linkage between quality development and control and service applicationhas been shown and explained. INTRODUCTIONThe refractory industry is no stranger to change. New processes and revision of old processes in other industries are the harbinger of new and revised products in refractories.Few of the changes are dramatic; generally they are evolutionary rather than revolutionary. New developments are additional to, and inclusive of, established practice.Therefore in this paper it is necessary to repeat much of what is already known in order to show the development taking place.FIRECLAY REFRACTORIESGeneral technology Fireclay refractories are the most common, the most varied and the most versatile of all refractories. Virtually any composition of silica and alumina up to the composition of kaolin is possible. For purposes of comparison they may be classified in the Continental fashion in accordance with chemical composition or in the American way according to "duty". That the two methods are equivalent is shown by an inspection of the alumina-silica diagram of Bbwen and Greig (1924). 'Fireclay refractories are composed of a glassy and a crystalline component derived from the chemical and physical nature of the raw materials used in their manufacture.

Jan 1, 1961

The sulphide ores of the principal lodes of the Boulder Mines are mainly composed of a schistose guess with a varying proportion of silica and lime, containing tellurides of gold, silver and mercury, associated with iron pyrites. It is a great difficultyto obtain pure and homogeneous samples of the tellurides for analysis, and from a number of tests made with excellent specimens it was found hardly possible to procure two to agree in analysis, the precious metals being found to be combinedwith tellurium in most varying proportions indeed, a close inspection of a partially crushed specimen will reveal, even to the naked eye, the various shades of colour characteristic...

Jan 1, 1901

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

By K Gordon, A Black

Two remediation strategies have been considered to reduce the levels of acidity and dissolved metals in acid mine drainage discharging from Sullivan Mine, West Coast, New Zealand. The oxidising strategy involves adding alkalinity and dissolved oxygen (DO) resulting in the precipitation of metallic oxides and decreased acidity. The reducing strategy involves removing DO, resulting in the precipitation of metallic sulfides, followed by addition of alkalinity to decrease acidity. Field remediation trials indicate a reducing system may be more effective for this site than an oxidising system. A residence time of only two hours in the limestone layer of a successive alkalinity producing system (SAPS) is sufficient to reduce acidity by 100 per cent, iron by 71 per cent, aluminium by 59 per cent, nickel by 38 per cent and manganese by 26 per cent. The proposed remediation plan will likely include a series of SAPS, followed by an anoxic limestone drain, and settling ponds to capture any remaining precipitates.

Jan 1, 2003

By N Currey, G Corder, G Becker

"The SUSOP« Framework is a new technique that helps incorporate sustainable development principles and objectives into the design and operation of businesses. Developed through the Co-operative Research Centre for Sustainable Resource Processing, it brings a design methodology to sustainability, similar to what hazard and risk techniques such as HAZOP did for safety.Metallica Minerals Limited (æMetallicaÆ) adopted the SUSOP« framework to help identify opportunities and risks that could directly improve or affect its flagship SCONI (nickel-cobalt and scandium) project. This project has the potential to become the worldÆs largest producer of scandium oxide (æscandiaÆ) which is used in solid oxide fuel cells and strengthens aluminium alloys. Located northwest of Townsville in Queensland, the plant site will be located within the previously mined and partially rehabilitated Greenvale Nickel Mine. By applying the SUSOP« framework through a series of multi-disciplinary workshops and offline analysis, Metallica was able to identify numerous sustainability opportunities and risks. Opportunities were clustered together to form concepts to develop a more holistic understanding of the projectÆs overall potential contribution to sustainable development as well as determine where key risks could be mitigated. Four key concepts were identified: Waste and Water Workforce Community and Enterprise Development Energy and Greenhouse Gases (GHG). Metallica was able to include a range of initiatives that could deliver enhanced environmental, social and community outcomes into their mine development plan. These included measures to reduce reliance on water, reduce the volume of waste, provide local opportunities for training and skilled employment and create support for local enterprise development. These measures also resulted in a significant reduction in the capital estimate of the project.This paper provides an overview of the SUSOP« framework, details its application to the SCONI project and discusses the outcomes that will help establish the projectÆs strong sustainable development credentials and improved business outcomes.CITATION:Corder, G, Currey, N and Becker, G, 2013. Sustainability, made easy - A business improvement case study, in Proceedings MetPlant 2013, pp 259-271 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By R J. Mills, B S. Sinclair, D A. Fergusson, A G. Goldstone

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. The consenting of major mine site activities has historically required wide consultation and involves notification of the application.   The risk and cost associated with consultation can be significantly reduced via a non-notified process. A non-notified consenting process necessitates environmental effects to be shown to be æless than minorÆ, which requires the combination of robust science and a pragmatic approach to design, assessment of environmental effects, and consenting issues.   Key issues examined included consideration of how to practically operate a significant disposal project within the confines of an operating mine, minimising the costs, civil and geotechnical design and practical issues associated with traditional disposal. Environmental issues specifically related to the coal ash, led to a site specific performance driven approach to management rather than relying on conventional prescriptive approaches. Environmental issues of concern include the leaching of boron and aluminium from ash into groundwater and mine water management systems where both boron and aluminium can occur at elevated levels.   Coal ash exhibits unusual geochemical characteristics reflecting the primary coal composition and the combustion process. The dominant coal type combusted at the Huntly Power Station is derived from Rotowaro and the resulting ash is cementitious and has a high alkalinity. As a result the disposal design is based on the characteristics of the ash itself rather than the material into, or onto which the ash is disposed. Non-notified status was able to be achieved through consideration of these key characteristics of the ash, ensuring that the dimensions of the disposal site and each location was designed to minimise the flow of groundwater through the ash and demonstrating that the physical ash disposal effects are less than minor compared to the consented mining operation.

Jan 1, 2006

A research project was commissioned by the Australian Coal Association Research Program (ACARP) to improve the understanding of tailgate strata mechanics and to provide a more rigorous engineering basis for tailgate support design. A deformation mechanism termed æskew roofÆ was defined which relates the regional influence of differential horizontal strata movement (shear) about longwall extraction to gateroads. Confirmation of the mechanism was achieved by field investigations which included measurement of the shear displacement along weak interfaces. Under geological and mining conditions where the skew roof mechanism operated, strata units were found to move progressively further towards the goaf with height into the roof. 3D numerical modelling was used to assess the major geotechnical factors controlling the mechanism and to determine appropriate support strategies within a æskew roofÆ environment including the role of cables versus standing supports. The skew mechanism is considered relevant to; all roadways in the vicinity of longwall extraction including the faceline itself, chain pillar design, and support design.

Jan 1, 2005

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dike intrudes Ordovician-Silurian metapelite and quartzite. These metasedimentary rocks have undergone three phases of folding: a first phase of recumbent folds (F1), a second phase (F2) of northerly-trending inclined folds with a prominent crenulation cleavage, and a third phase (F3) of steeply plunging folds. The granite porphyry dike has a thickness of up to 40 m and intrudes thin lamprophyre dikes along its contacts. Deflection of the crenulation cleavage around the granite dike, shearing within the dike and its sinuous outcrop pattern indicate that the granite dike has been deformed during F2 and F3. The granite has been hydrothermally altered, with a first stage of magnetite-ankerite alteration. This first stage is cut by a second stage of quartz-pyrite veins and a third stage of sulphide, quartz and ankerite veins, accompanied by pervasive silicification represented by quartz-perthite-albite-rutile¦pyrite-ankerite-sericite assemblages. Lamprophyre is altered to an ankerite-chlorite-sericite assemblage. The sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite. The altered granite and the veins have been deformed and recrystallised. The competent sulphide minerals pyrite and arsenopyrite are fractured and brecciated, with fractures locally filled by galena, a ductile sulphide mineral. Vein quartz shows local cataclastic and mortar textures and develops pressure shadows around arsenopyrite. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre. These features together with the style of veining and the sulphide mineralogy indicate that the mineralisation was formed from a magmatichydrothermal fluid that was sourced from the granite. Oxygen, carbon and sulphur isotope values of the vein minerals (quartz, ankerite and sulphides) are also consistent with a magmatic source.

Jan 1, 2003

By H W. Wu

The objective of this paper is to examine some modern forms of auxiliary ventilation fabric ducting with streamline design fittings and the efficiency of construction practices. The most dynamic form of auxiliary ventilation is a moveable fan and ducting, which is easy to install and uses light weight fabric. The porous nature of some ducting construction results in leakage and loss of efficiency. Flexible fabric ducting is primarily associated with metalliferous mining and industrial material quarrying. Some applications are found in coal in stone/rock development and with use of dust scrubbers.Forcing auxiliary ventilation systems employing circular fabric ducting have been examined. Leakage of air from ducting is affected by ducting material and construction methodology (such as welded or sewn), quality of installation, number of joints, total length, pressure differences between the inside and outside and diameter. The best ducting system with welded construction can have up to four times less leakage as compared with some systems with sewn construction. It is also evident that the sewn type ducting will deliver less air to working faces and require more fan power, hence higher operating costs to run when connected to the same fan.A case study has also been undertaken to compare predicted operating costs of auxiliary ventilation systems connecting various types of ventilation duct fittings. The study also assesses the technical importance of streamline design with low aerodynamic resistance to reduce the shock losses of the duct fittings. It was found that the system connected with streamline designed fittings is able to provide some power cost savings and deliver more air compared with the system fitted with conventional fitting pieces.Using a ventilation ducting system with a lower leakage and frictional characteristic represents a sound solution to new challenges faced by the industry for increasing demand for better quantities and quality of air delivered to working faces; this is due to higher production schedules and stricter mine health and safety regulations within the Australian mining industry.CITATION:Wu, H W and Gillies, A D S, 2017. A comparison of auxiliary ventilation systems and their predicted operational performances, in Proceedings Australian Mine Vent Conference 2017, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Following the Coalbrook Colliery disaster in 1960, Salamon and Munro (1967) established the well known empirical coal pillar strength formula in South Africa. This formula has prevented further violent multiple pillar failures. In 1996, a back analysis of the collapsed and uncollapsed cases in Australia led to the development of the Australian empirical coal pillar strength formulae. The original collapsed and uncollapsed coal pillar database of Salamon and Munro (1967) was updated in 2006. This study introduced various strength formulae for different coalfields and seams in South Africa through back analyses of collapsed and uncollapsed cases. Today, the resultant pillar strength formulae from these previous studies and the behaviour of coal pillars are mostly well understood and applied with confidence. However, it was assumed in the previous studies that the behaviour of pillars is not time dependent; therefore, the formulae established do not provide an associated time to failure of coal pillars. This paper attempts to evaluate the so called 'Geometrical Limits' concept to provide the Australian coal mining industry with a tool to assess the long-term behaviour of bord and pillar workings where the pillars are prone to failure due to spalling of ribs. In order to achieve this outcome, the principles of the safety factor concept and the probability of failure calculated using the coal pillar strength formulae have also been evaluated and practical design examples are presented in this paper.

Nov 25, 2010

It has been thought in the past that New Zealand had ample coal reserves, able to provide fossil fuel supplies well into the future. Such is not the case and every effort must be made to achieve the highest possible extraction rate in all new coal mining ventures. While the relative cost and availability of completion or fuels has been largely responsible for the slow growth of coal production in the past, a world shortage of fuels has given coal a new importance and required better utilisation of coal reserves. New mining ventures in thick-seam coal deposits cannot be planned and designed without geotechnical investigations designed to provide information required by the mining engineer and analyst. Finite element analysis of mine workings may provide essential information on the optimisation of mining techniques and the design of underground support and roadway shapes.

Jan 1, 1976

By J G. Webster-Brown, K L. Brown

The Waihi Region is host to many low sulphidation epithermal Au-Ag deposits. The Golden Cross mine located at the head of the Waitekauri River, eight kilometres NW of Waihi, was a gold mining operation that placed significant emphasis on environmental management. An assessment of the influence of this mining project on stream sediment geochemistry (Fe, Mn, As, Cu, Pb, Zn, Cr, Cd, Ni, Ag and Se) in the Waitekauri Catchment has been made. Effective waste management during the mine operation appears to have prevented contamination of stream sediment. Trace metal concentrations in the Waitekauri Catchment sediment have generally decreased since 1987, and are currently mainly below the ANZECC (2000) sediment quality guidelines. However, elevated As levels were recorded in the Upper Waitekauri River and Battery Stream, exceeding guideline values. Elevated levels of Cu, Pb, Zn and Cd were found in the Huanui Stream, a tributary of the lower Waitekauri River. This reflects the influence of past mining operations in the valley, as well as natural weathering of hydrothermally altered Coromandel Group andesite. At a number of sites, Mn concentrations also exceeded sediment quality guidelines, and this may be derived from the remediated Golden Cross mine site.

Jan 1, 2003

Developments in the technology of explosive production and deliveryallow a greater amount of flexibility in rock fragmentation by blasting. The rock fragmentation efficiency of an explosive is currently given by a rating which is determined by the explosive manufacturers using proprietary formulae and methodology. Hence, comparison of explosives from different manufacturers may be misleading. Modeling of explosive energy, using a thermochemical code such as CHEETAH provides an objective standard by which the likely performance of different explosive formulations can be determined. Such modeling can be used for optimisation of explosive composition to match specific rockfragmentation objectives.

Jan 1, 2001

Study on the New Flow Sheet and Wastewater Recycling for Xiaoliuguo Copper-Bearing Low-Grade Scheelite Ore

Sep 13, 2010

Core samples, which were collected by the author from the Busang prospect, East Kalimantan, reflect a progressive evolution of a large magmatic-related hydrothermal system that is comparable to that encountered in many similar systems elsewhere in the Pacific region. The initial, localized deposition of sheeted porphyry quartz-molybdenite veins took place at high temperatures and fluid salinities, and at relatively deep levels. This was followed by an extensive phase of phyllic (sericite-quartz-pyrite ¦ tourmaline-apatite) wallrock replacement and vein formation. Propylitic (epidote-chlorite-carbonate-quartz) alteration was formed marginal to the phyllic assemblages. These porphyry-related events were centred in the Southeast Zone, and are probably associated with the emplacement of a felsic intrusion at depth. This event contributed only trace gold to the system. The early stages of hydrothermal activity were followed by an episode of quartz (¦ adularia) û carbonate û base metal sulfide veining, which was accompanied by argillic (illitic-kaolin clay) wallrock alteration. This event was sulfide-rich in the Central Zone and carbonate-dominated in the Southeast Zone. Gold mineralisation was observed in Central Zone drillcore to be associated with both sulfide, as well as carbonate, deposition. A final stage of epithermal-style quartz ¦ stibnite û realgar veins are, in the Central Zone, locally gold-bearing. The latter two events are interpreted to be associated with the late-stage exsolution of metal-bearing brines from the felsic intrusion that formed the earlier porphyry quartz-molybdenite veins and widespread phyllic-propylitic alteration.

Jan 1, 2002

Soon after the Rosebery concentrator commenced operations in 1936, an investigation was begun in an attempt to discover a substitute for cyanide in lead flotation. Cyanide is an excellent depressant for zinc and iron, but it also powerfully depresses the copper, silver and gold bearing minerals present in Rosebery ore, thus allowing them to pass through to the zinc concentrate or final residue where they are of little or no value.The investigation was not entirely successful, but it did indicate that sodium bisulphite or sodium sulphite could be used as a depressant for zinc without depressing the copper, silver and gold bearing minerals. The sulphites were, however, much inferior to cyanide as apyrite depressant.At about this time, I. W. Wark, using the captive bubble technique, had shown that, at the concentrations normally used, sodium aerofloat is not a promoter for pyrite or galena in alkaline solutions (see his book "Principles of Flotation", p. 188). Some preliminary tests on the production of a copper concentrate from Rosebery ore were therefore carried out using sodium sulphite as depressant and sodium aerofloat as promoter.The results of this work were promising but, since Rosebery ore usually carries only about 0·5% copper, there did not seem to be much incentive to carry the work further. With the outbreak of war, however, Australia became desperately short of copper and the relatively small amount in the ore. became of sufficient importance to...

Jan 1, 1952