Search Documents

By Whitmore R. L

The action of water on a number of Queensland shales which are associated with particular coal measures and oil shales has been studied. The results suggest that the disintegration of some of the shales could cause significant problems in mining and preparation operations. The extent of shale breakdown varies widely from deposit to deposit and from seam to seam but a suitable assessment procedure utilises the test described in AS 1661-1979, and an improved method of presenting the results is described in the paper.

Jan 1, 1982

Ore sorting is a high capacity, low cost method of pre concentrating ores and in some cases of producing a marketable concentrate. In most cases it is applied to run of mine material, immediately after primary crushing and screening in sizes ranging from 10 mm to 150 mm. Recent developments in bulk sorting of friable uranium deposits have resulted in machines capable of handling fine materials with sensing and separation being achieved on a zone by zone basis. Modern ore sorting machines rely on the synchronous operation of four internal subsystems, feed presentation, sensing, data processing and separation. A variety of different sub systems is available which can be combined in various forms to produce sorters capable of handling a wide variety of mineral types. The benefits in using ore sorting cover a wide range of situations and are applicable to both established mines as well as new mining ventures. Reduced operating costs, increased productivity, capital savings, energy and resource conservation and environmental issues are all part of the reason why ore sorting is finding rapid acceptance in today's mining industry. The suitability of different ore types for pre-concentration using anyone of the variety of ore sorting systems can be quickly established using computer based techniques which require only small samples of the materials under investigation.

Jan 1, 1980

The acid plant consists of the following units: 1. Glover tower. 6. Mills-Packard type chambers. 3. Reaction towers. 6. Gay-Lussac towers.The sulphur dioxide bearing gases, used in the manufacture of the acid, are obtained from the roasting of zinc concentrate. Six Herreshoff type furnaces are available, each with an effective hearth area of 520 sq. ft.The concentrate contains approximately 30% sulphur, of which about 72 is ultimately recovered as acid. The oxides of nitrogen are added to the gases in the requisite proportions partly from nitrous vitriol and from nitric acid in the Glover tower, and partly from nitrous vitriol in some of the chambers and connecting flues.The acid leaving the Glover tower is cooled by the ordinary water-cooling coils, while the cooling of the chamber gases is effected by circulating water over the outer surface of the chambers, and by spraying nitrous vitriol and weak acid into them.Flow of gases throughout the plant is regulated and controlled by means of regulus metal fans, fitted with variable speed gears.

Jan 1, 1934

The mineralogy of the rocks now observed in the Nairne pyrite deposit developed under conditions of internally-controlled sulphur activity during amphibolite facies metamorphism. In the sulphide-deficient metasediments the activity of sulphur was low, and pyrrhotite developed with iron-bearing silicate minerals. At higher sulphur activity, in the sulphide-rich meta-sediments, pyrite formed in addition to pyrrhotite, and the associated silicate minerals are iron-deficient.

Jan 1, 1969

By P. J. Knottenbelt

Outcomes from a workshop organized through the SAIMM revealed that the minerals and metals industry must develop its ?Engineering Team? if it is to continue to meet the challenges of globalization. The very economy of the country is largely dependent on a competitive and stable engineering team within the minerals and metals sector. With the Chamber of Mines (COM) passing on its education and training initiatives to the industry, the professional bodies like SAIMM must (despite meagre resources) continue the good work done through the COM in the past. The workshop highlighted recruitment and selection, further/higher education, socialization and initial training, deployment and retention and continuing education as priority areas. These are further detailed in this report. Office Bearers have considered the outcomes and the areas where the Institute should or should not be involved have been stated.

Jan 1, 2002

James Barnes is Managing Director of James Barnes & Associated Ltd which is a company that has invested ten years of development to provide developers with a transparent, user friendly consultation framework that identifies who needs to be consulted, how they are to be consulted and procedures required to manage the risks associated with getting all the wrong! Despite the assertion above, this paper is not about to provide delegates with the answer to whom they ought to consult or identify the expectations that Maori might have in regard to the consultation process. It would be a very brave person indeed who would venture an opinion on such a sensitive subject. There are no short cuts to finding out what expectations Maori might have on any given situation. Nothing can be taken for granted. What this paper will attempt to do however is provide practical insights into what might be on the minds of Maori interests as they deal with the issues associated with mineral resources, particularly those under Treaty of Waitangi Claim. The Treaty of Waitangi has a significant bearing on the current debate between Maori and the Crown regarding ownership of mineral resources in New Zealand. The Waitangi Tribunal is currently hearing a case presented by a number of Iwi over the ownership of oil and gas resources in Taranaki and Hawkes Bay. Others will follow. The Crown and Maori have never been able to settle differences over ownership rights without resorting to legal action and it looks like this scenario is about to be repeated in regards to minerals. The Crown has a duty to actively protect the Maori interest. This is a fundamental expectation in the relationship between Maori and the Crown. In the case of minerals, Maori have yet to see the Crown do its duty. The impact on developers has become evident through Maori objections to consent applications as the issues of mineral right remain unresolved.

Jan 1, 2000

"4.1. IntroductionThis chapter reviews the geochemistry of the platinum-group elements (POE) in sulphur-poor silicate rocks, and the limited data on POE in silicate, oxide, sulphide, arsenide and sulpharsenide minerals. The earliest geochemical studies of POE in silicate rocks, minerals and meteorites were carried out mainly by Goldschmidt, the Noddacks and their co-workers, and are reviewed in Crocket (1969). These researchers established the siderophile character of the POE, emphasized the common association of the group with sulphides in ultramafic-mafic rocks and suggested that very low concentrations of POE are typical of sulphur-poor silicate rocks and minerals. Much of these data were for Pt and Pd only and are more than 50 years old. Because of the poor sensitivity typical of the available analytical methods, few reliable data were obtained on silicate rocks in these early studies. Surveys of POE geochemistry demonstrate that the data base for sulphur-poor silicate rocks is very restricted, although considerable highquality data for Pd and Ir have been accumulated (Wright and Fleischer 1965, Yushko-Zakharova eta/., 1967, Mertie 1969, Crocket 1969, 1979, Keays 1981).Two recent publications, Vol. 71, No. 7 (1976), of Economic Geology (An Issue Devoted to Platinum-Group Elements) and Vol. 17, Part 2 (1979), of The Canadian Mineralogist (Nickel-Sulphide and Platinum-Group-Element Deposits), are of special interest. These volumes are clear testimony to the impressive progress made in the last decade toward describing the mineralogical and geochemical aspects of POE ore deposits, but at the same time demonstrate the constraints in modelling POE ore genesis due to our meager knowledge of the. POE content and distribution among minerals in the source rocks of ultramafic and mafic magmas. It is clear that the phases hosting POE in mantle source rocks are poorly understood. Nevertheless, Naldrett and Duke (1980) have shown that the absolute and relative concentrations of POE in magmatic sulphide ores are related to the degree of partial melting of mantle peridotites, and subsequent processes of batch equilibration and fractional segregation of sulphides."

Jan 1, 1979

By Mark A. Williams, James D. Humphrey

Without question, draglines are one if not the most effective tools available to the surface mining industry for overburden handling. With few moving parts and a two- or threeman crew, this machine silently sits and chews into millions of yards of overburden annually. A 100 cubic yard machine operating for 30 years will excavate three-quarters of a billion yards of material during that time. That is 750,000,OOO yards of material!

Jan 1, 1990

By Johnston W. H

MINING operations in the Waihi mine began, under the present proprietorship in the year 1889. Previous to this, and as far back as the year 1880, the presence of reefs in the Martha Hill had been known, and surface working on a small scale had beencarried out, without any great measure of success. The only method of treatment in use at this time was the old system of light stamps, amalgamating tables and berdans, and recovery by this method being low, little margin for profit was left, so thatthe property in these days was not considered of great importance and work on the area was only carried on spasmodically by different owners.On the transfer of the leases to the present company, calcining, dry crushing, and hot pan amalgamation was adopted as the method of treatment, and this system was continued till the more modern cyanide process was introduced and applied. As themethods of treatment and gold-saving became more efficient with the application of more modern and scientific processes, the importance and future prospects of the mine became more and more pronounced, and mining on a larger and more comprehensive scale was gradually established.As in the case of ore treatment, mining methods in the early stages were not as far adv.anced as the adopted practice of today, and numerous shafts, levels close together in vertical height.

Jan 1, 1912

By R. P. Smith

In 1937 the employees of the Hollinger Consolidated Gold Mines Ltd.. at Timmins. Ont., Canada, approached organized medicine for a plan to provide themselves and their families with a complete medical service including hospitalization. This approach was made because of two conditions: (1) the necessity for some organization whereby contributions could be made in instalments to offset the sudden and large expense connected with illness for which the average employee is not prepared, and (2) the need for a more cohesive quality of service to replace a contract practice then in vogue, which did not take care of the employee's family or dependents. In different parts of the United States and Canada similar plans were in force, not only for employed groups but for numbers of people in circumscribed areas. In Europe different countries had adopted various forms of health insurance plans. It then was no surprise that these employees as a group should ask for some similar plan. With the cooperation of the management, a plan was instituted. The plan has one object only—the provision of medical services, including the accessory services such as hospitaliza-tion, X-rays, nursing, and necessary drugs and medicines. It is not concerned with cash benefits, sickness and accident payments, or any form of monetary return as the result of illness, but is simply an organization to provide medical services and pay for them from a central fund. It is a nonprofit organization and the only shareholders are the employees and their families who contribute and who in turn receive services. The Hollinger plan is limited to the employees of the Hollinger mine, who live in Timmins and the immediate vicinity. At first, the membership was voluntary. In the third year, it was made a condition of employment, with the proviso that at the end of any Association financial year an employee may withdraw if he wishes to do so. After withdrawal, he cannot again become a member until the end of the next Association year, and then only by the payment of the back dues. This step was taken to ensure continuity, and to prevent employees from withdrawing when well and reentering when faced with impending illness or operations. The employee himself is subject to medical examination on application for employment, and if accepted is subject to further examination by a specialist in chest diseases under the Workmen's Compensation Board of Ontario. Thus it is possible to exclude those who have heart disease, tuberculosis, or other disabling conditions when first employed. Wives and families of employees are not subject to medical examination but other dependents of an employee—mother, father, or other relative—who are declared by the employee to be wholly dependent upon him must be examined. The employee

Jan 1, 1946

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of elastomeric noise abatement materials with a limited effort expended on the evaluation of specific treatments applied to mine timbers. Under the conditions employed, for a dimethyl silicone rubber, formaldehyde presented the major toxic threat; acrolein was the main toxic species for both polyester and polyether urethanes and an acrylonitrile-butadiene-styrene resin; in the case of flame-retardant styrene-butadiene rubber compositions, hydrogen chloride, and in the case of PFA-treated timber, furfural, were the major toxic compounds. Of the materials studied, the flame-retardant styrene-butadiene rubbers presented the greatest toxic hazard. The generated data have been reduced to toxic load tabulations amenable to employment for potential hazard assessment.

Jan 1, 1982

By Aline Maria dos Santos Teixeira

Serpentinite is an ultra basic and metamorphic rock consisting mainly of magnesium, calcium and silicon oxides. The rock under study is a host rock of chromite mine located in Andorinha, BA. The objective of this paper is to evaluate the rock's physical and chemical characteristics to be used as an additional fertilizer of acid soils. After comminution, rock samples were submitted to chemical analysis, XRD, SEM-EDS and TGA. Afterwards, particle size distribution was determined. Result analysis confirms that our rock consists mainly of dolomite, calcite and diopside. According to the result obtained, it can be said that the serpentinite rock has promising applications in agriculture for the correction and additional fertilization of acid soils. However, it is necessary to study the characteristics of the rock such as its dangers and toxicity as well as evaluate them according to the legislation for corrective acidity.

Jan 1, 2010

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By J. Geertsma, F. de Klerk

During the hydraulic fracturing treatment of an oil or gas well the liquid pressure in the borehole is increased until tensile stress in the surrounding rock exceeds tensile strength. Once a tensile fracture is initiated, it is penetrated by liquid from the borehole and fracture propagation under continuous hydraulic action takes place. The fracturing liquid carries a propping agent to ensure a highly permeable flow channel after pressure release. Field results range from failure to obtain increased production to outstanding success. In all cases, however, it unfortunately remains uncertain whether the values chosen for the operational parameters, such as injection rate, pumping time and fluid viscosity, were in fact the ideal ones. Though experience provides a lead, a more satisfactory way to predict results would seem to be to subject the fracture propagation process to a theoretical analysis that (1) makes the maximum use of the relevant physical information and (2) so simplifies the resulting calculations that the field engineer gets practical data that he can handle comfortably. We are attempting here to do this in connection with the prediction of fracture width and areal extent before pressure release. What remains of the fracture afterwards depends on the distribution of the propping agent between the fracture walls, and that is a separate story. Idealization of the Problem To keep the problem tractable, a number of simplify- ing assumptions have had to be made: 1. The formation is homogeneous and isotropic as regards those of its properties that influence the fracture-propagation process. 2. The deformations of the formation during fracture propagation can be derived from linear elastic stress-strain relations. 3. The fracturing fluid behaves like a purely viscous liquid; i.e., any peculiar flow behavior due to the addition of gelling agents or other additives is neglected. Moreover, the effect of the propping agent distribution on the distribution of fluid viscosity in the fracture is not taken into account. 4. Fluid flow in the fracture is everywhere laminar. 5. Simple geometric fracture-extension patterns are assumed — either radially symmetrical propagation from a point source (Fig. 1A) or rectilinear propagation originating from a line source (Fig. 1B). In the first case the periphery of the fracture is circular, in the second case it is rectangular. 6. A rectilinear propagation mode can be accomplished only by injection over a large perforated interval, thus forming a line source. Such a rectilinear fracture must therefore be located in the vertical plane. A circular propagation mode might be expected from injection through a narrow band of perforations. This forms a point source. Because gravity effects are excluded from our considerations, the fracture propagation plane may in this case assume any angle with respect to the wellbore as far as the

Jan 1, 1970

Using Mineral Maps to Rank Potential Processing Behaviour

Sep 13, 2010

By José Cuadros

"El presente trabajo señala el proceso de evolución del método de minado en la mina Chupa, perteneciente a la unidad minera de Iscaycruz. La evolución del método de minado se determinó por la búsqueda de mejores condiciones de seguridad y eficiencia en la operación. En ese sentido, los resultados logrados con cada una de las alternativas de minado por subniveles, indica que se ha logrado optimizar las diferentes variables mineras y cumplir con el plan estratégico de Empresa Minera Iscaycruz S.A. (EMISA). Para cumplir con el citado plan estratégico, se debe optimizar el método de minado de Chupa, a través de una mayor producción a un menor costo,así como del aprovecho de las labores de desarrollo y preparación ejecutadas según el planeamiento inicial del minado. Por ello, la secuencia del avance del minado y la reestructuración del sistema de relleno de la mina son los aspectos importantes para lograr este objetivo. "

Jul 31, 2003

By J R. Manuel, J M. F Clout

The importance of goethite to Australian iron ore production is steadily increasing as the proportion of goethite-rich, martite-goethite bedded and channel iron deposits increases at the expense of declining production from high-grade microplaty hematite deposits. For this reason, an improved understanding of goethite in iron deposits, its genesis, goethite types and their physical and metallurgical properties is vital to maintaining optimum sintering and blast furnace performance in Asian steel mills.The terminology used to describe goethite in Australian iron deposits is currently highly variable. The discredited mineral name ‘limonite’ is still in widespread use as a field term for goethite and there are many misconceptions concerning goethite chemical grade and downstream physical and metallurgical properties. The goethite classification proposed here is based on geological and physical properties from which three types are recognised including brown goethite, dark brown-black vitreous goethite and highly microporous, friable yellow ochreous goethite.In practice, typical vitreous goethite with highly reflective surfaces and conchoidal fracturing, characteristic of the hard cap zone appears from X-ray fluorescence (XRF) and electron microprobe analysis to be significantly higher in Si (up to 18.7 wt per cent), Al (up to 3.5 wt per cent) and S (up to 0.14 wt per cent) compared to the generally very low (<1 wt per cent for Si and Al) levels of these elements in ochreous goethite and brown goethite. The data dispels the common misconception that friable earthy or yellow ochreous goethite is high in Al and Si and other chemical impurities. However, P was found to be consistently higher (mean of 0.112 wt per cent and up to 0.296 wt per cent) in ochreous goethite than brown goethite (mean of 0.011 wt per cent) or vitreous goethite (mean of 0.031 wt per cent). The highly porous microstructure of ochreous goethite is thought to have a much higher surface area, which may aid in preferential adsorption of P onto the ochreous goethite mineral surface.CITATION:Manuel, J R and Clout, J M F, 2017. Goethite classification, distribution and properties with reference to Australian iron deposits, in Proceedings Iron Ore 2017, pp 567–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By Michael D. Balen

The Bureau of Mines (Bureau), in cooperation with the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted field investigations from 1987 through 1989 in the 5.7 million-acre Valdez Creek Mining District (VCMD) in south-central Alaska. The objective of the VCMD investigation was to evaluate the mineral resources and the mineral development potential of the mining district. The investigation was part of the Bureau's continuing statewide mining district evaluation program. Nineteen new mineral occurrences were identified as a result of this investigation. Reconnaissance placer sampling resulted in the identification of 10 previously unreported occurrences that primarily contain gold, however, some contain subsidiary platinum-group metals and/or tin. Reconnaissance lode sampling resulted in the identification of two gold-silver occurrences, three platinum-group metal occurrences that contain elevated quantities of subsidiary chromium, nickel and/or cobalt, three copper occurrences that contain subsidiary molybdenum or zinc, and one zinc occurrence.

Jan 1, 2011