Search Documents

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

I find that during the short time I have been in this district, the majority of boilers are, and have been, receiving very bad usage owing to the difficulties which they have to contend against, viz., oil and bad water. Oil on the heating surface of a boiler is of a highly dangerous nature inasmuch as it allows the surface to become overheated, owing to the water not coming into direct contact with the plates, and it naturally follows that when the crown sheets of a flue or firebox become overheated, you lose a considerable amount of the strength of the plate, and the flue or crown comes down. Referring to the oil question, I find that too much care cannot or exercised on the part of engine drivers in order to minimise as much as possible the internal lubrication of the various engines under their control. For I consider that it is here that the most of the trouble is caused. My reasons for stating such to be the case, are:-That the majority of enginedrivers before coming to this field have been used to driving engines that have been exhausting into the atmosphere, and probably they have been taught that it is far better to use a little extra lubrication than to have a hot bearing. So far so good. But one thing that must not be overlooked is that on these fields the conditions are altered in this respect, as the majority of engines in this district are not exhausting into the atmosphere, but are condensing their exhaust steam and using the water so condensed for feed purposes.

Jan 1, 1901

By Thomas M. Barczak

Roof support systems are necessary to provide stable mine openings and much research has been conducted to design a variety of roof support systems that will function in various manners to ensure that stable ground conditions are achieved. Despite these advancements in technology, mistakes continue to be made in the evaluation and/or installation that significantly degrade the support capability or lead to erroneous determinations of support expectations. The purpose of this paper is to discuss misconceptions about how roof supports perform and factors that impact their performance. The goal is to present practical information that will assist mine operators and engineers in selecting, installing, and evaluating roof support systems properly, and help them to avoid mistakes that can lead to erroneous expectations and potentially catastrophic results that may lead to roof falls. The paper is limited to a discussion of secondary roof support systems and powered roof supports such as longwall shields.

By A. Taylor, M. Blanchette, J. Doucet

"A Z1600 Jameson Cell Test Rig was rented for test work at Vale’s Clarabelle Mill operation. This paper discusses the evolution of renting the unit for test purposes to owning the unit and operating it as a revenue generating process component. The paper focuses on three aspects of the Z1600 project; the initial rental and installation, the test work performed in the cleaning circuit, and the business factors which led to the unit being permanently incorporated into the copper circuit.INTRODUCTION Clarabelle Mill is located in Sudbury Ontario (approximately 350 km north of Toronto) on the southwest rim of the Sudbury basin a meteoric impact crater that is 62 km long and 30 km wide. The result of the meteoric impact was concentrated nickel (Ni), copper (Cu) and platinum group metal (PGM) ore bodies in the outer perimeter of the basin; described in more detail by Hanley (1957). Vale currently has seven operating mines in the Sudbury basin, from which nine distinct ore types are mined. Ores are also received from two QuadraFNX mines. Clarabelle Mill processes all of these ores for the Ontario Operations of Vale. The mill, commissioned in 1971, was originally built as one of four mills operated by then Inco Limited. Between the late 70’s and the early 90’s process changes were made to consolidate the Sudbury Operations milling processes into a single operating mill, Clarabelle Mill. In 1990, the SAG mill was installed resulting in peak mill throughput of 11.9 million short tons per annum (Mstpa), with typical throughputs of ~10 Mstpa. Mill average feed grades were 1.4% Cu and 1.2% Ni. During the resources boom, plans were developed to increase the mill capacity at Clarabelle Mill in stages to a final capacity of 13.5 Mstpa. The project known as the Clarabelle Mill Expansion and Recovery Project (CMERP) included expansion and reconfiguration of the grinding and flotation circuits. The first stage was a planned increase in grinding capacity with the reallocation of existing mills, the existing flotation capacity would be required to treat higher throughput until the new flotation circuit was constructed."

Jan 1, 2012

By B Belle

Dust sampling is pivotal in estimating the ‘dose’ of dust exposure and in deriving dose-response curves in epidemiological studies. Over the last half century, gravimetric sampling has been the fundamental means for dust exposure monitoring using recognised respirable size-selective standards. In Australia, a gravimetric sampling technique has been followed since 1983 using the Higgins-Dewell (HD) type cyclones (AS2985). The re-emergence of ‘Black Lung’ or Coal Workers Pneumoconiosis (CWP) in Queensland, Australia has re-kindled the need for better understanding of personal dust monitoring, compliance determination, accuracy, timeliness of sampling results and dust control systems. Reporting dust levels in real time empowers miners and operators to take immediate action to avoid being exposed to excessive airborne dust. Two decades of intensive research in the USA has led to the introduction of gravimetric based continuous personal dust monitors (CPDMs) called PDM3700 as compliance tools. The new real-time mass based sensor is a continuous mass based dust monitor using the Tapered Element Oscillating Microbalance (TEOM) principle and is regarded as significantly superior to the current gravimetric sampling methodology.Recently the overall respirable dust standard in USA coalmines has been reduced from the historic 2.0 to 1.5 mg/m3. This paper provides the results of a comparative pairwise study of an existing gravimetric sampler and the PDM3700 carried out in 3 different Australian underground mines. The field results consistently suggest that there is a significant ‘measurement bias’ between the current gravimetric HD sampler and the PDM3700 monitor operated using a similar HD type cyclone. The results show that the currently used cyclone measurements are approximately 59 per cent higher than the ‘auditable’ PDM3700 monitor data at the current compliance limit of 3 mg/m3. Based on a review of the extensive data collected, the differences can in part be attributed to the aerosol size selectivity of the samplers with the current gravimetric sampler used in mines, collecting more larger sized particles (D90 of 15 µm). This finding has significant consequences for historic exposure results and their use in medical surveillance programs, as well as the current approach to non-compliance determination.CITATION:Belle, B, 2017. Pairwise evaluation of PDM3700 and traditional gravimetric sampler for personal dust exposure assessment, in Proceedings Australian Mine Vent Conference 2017, pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Understanding multiphase particulate systems is essential for the further advancement of mineral processing technology. Characterisation, analysis, and simulation of these complex systems provide a fundamental basis for the development of improved mineral processing technology. One of the more recent tools that can be used to help provide a foundation for improved mineral processing technology is high resolution cone beam X-ray micro computed tomography (CT). During the past ten years point-projection X-ray micro CT systems have been used for 3D visualisation and quantitative analysis of multiphase particulate systems. Analysis of packed particle beds containing as many as 30 000 particles can be accomplished in less than three hours with special software to establish the 3D characteristics of each particle in the population and the spatial organisation of the packed particle bed. Now, due to advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. The development of software tools for the 3D characterisation, analysis, and simulation of packed particle beds using high resolution X-ray micro tomography (HRXMT) is discussed including examples of application in the areas of comminution (particle damage and preferential grain boundary fracture), exposure/liberation analysis (liberation-limited separation efficiency, including coal washability), and filtration/heap leaching (pore network structure of packed particle beds and simulated flow using the LB method of computational fluid dynamics).

Sep 13, 2010

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

Jan 1, 2001

By E. C. Hoeman, W. C. Stoecker, R. C. Redfield

"INTRODUCTION Industrial sands, characterized by specific physical and chemical proportion, are,essential new materials for the manufacture of glass, sodium siliante and other products. Sands of suitable characteristics are used extensively for molds and cores in the casting of metals as a granular medium in municipal water filters, as abrasives, as traction sand to prevent the slipping of driving wheels of self-propelled vehicles on trucks and in various ceramic and other structural forms. In addition to the use of common silicon sands in concrete, cement, and mortar, special sands find use in sand-lime brick oxychloride cement, and flooring, for coating prepared roofing, and for placing ware in saggers although sand for sandpaper has been mostly displaced by other harder mineral or synthetic grains, other abrasive uses are numerous and include sandblasting stone sawing, glass burnishing and finishing."

Oct 1, 1945

Tin mineralization in both eastern and western Tasmania shows a spatial correlation with middle Palaeozoic biotite granites and adamellites. The range of composition of these granitic rocks is restricted with respect to Mg, K, and Na content. Because this compositional restriction is shown by granitic rocks from other tin provinces, the concept of a genetic relationship between these granites and the associated tin mineralization is reinforced, and similar concentration mechanisms may be involved.Gold mineralization is largely restricted to eastern Tasmania and in contrast to the tin mineralization is rarely spatially associated with the middle Palaeozoic granitic rocks, although most authors have suggested a genetic correlation with hornblende and/or biotite granodiorites.Although few analyses are available, the granodiorites that are spatially associated with gold deposits exhibit similarities to granitic rocks from gold provinces elsewhere. These features suggest a possible genetic relationship between gold mineralization and the granodiorites.The composition of granitic rocks may be used as an aid to exploration in delineating areas of potential tin and gold mineralization in granite terrains.

Jan 1, 1970

Fragmentation Characteristics of Iron Ores from Anshan, China

Sep 13, 2010

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000

By Manuel Retamozo

El presente texto señala cómo el ejercicio físico adecuado y la dietética mejoran la producción y disminuyen el absentismo laboral en la empresa minera BHP Billiton Tintaya S.A a través de un política de prevención de salud. Entre los objetivos principales está determinar la frecuencia con que realizan ejercicio físico adecuado los trabajadores del área de mina, señalar si existieron cambios en las costumbres alimenticias de los trabajadores del área de mina después de la educación alimentaria, delimitar si existe asociación entre el aumento de la producción en el área de mina con la práctica del ejercicio físico adecuado y la dietética, así como entre la disminución del absentismo laboral en el área de mina con tales prácticas.

Jul 31, 2003

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By D. Fray

Electrochemical processing using molten electrolytes is undergoing a considerable renaissance due to several innovative ideas being explored both in the laboratory and also at the pilot scale. Several of these new ideas are related to developments in energy generation and storage and involve solid electrolytes. Sodium has been prepared by the electrolysis of sodium carbonate or sodium hydroxide with the transfer of sodium ions through a sodium beta" alumina membrane and magnesium oxide dissociated by the removal of the oxygen through a stabilized zirconiaelectrolyte incorporating a fuel cell electrode. By using halides with highly electropositive cations, such as molten calcium chloride, it has been found that the favoured cathodic reaction, when oxygen is present, is the ionization of oxygen and not the deposition of calcium. This approach has been applied to the reduction of many metal oxides including titanium, zirconium, niobium and rare earth oxides and, by using a mixture of oxides as the cathode, homogeneous alloys are produced. This concept can also be applied to deoxidation of solid and liquid metals. Refining of metals is possible using intercalation compounds and, in a completely different application, it has-been found that, by intercalating alkali metals by electrolysis of alkali halides into graphite, it is possible to produce carbon nanotubes and nanoparticles. The technological opportunities of these various concepts will be discussed.

Jan 1, 2004

By O. C. Blade

Total sales of diesel fuel in the United States continue to Increase. This growth is due primarily to two causes: More conversion to diesel units by the rail-roads In recent years, and the greater use of diesel engines in trucks, busses, and tractors. Following are some figures on the distribution of the fuel computed from data issued by the Bureau of Mines.2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,522,000 barrels during the first six months of 1955,3/ corresponding figure for 1954 was 91,170,000 barrels. Information on the properties of this engine fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1955

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By Muhammad Zia-ur Rehman, Sajjad Ahmad Baig, Gao Lei Fu, Muhammad Mohsin, Sobia Naseem

The environmental sustainability is linked back to human sustainability; the sustainability development comprises the environment, society, and economics. This study mainly focused on mining sustainability and its impact on the environment of Pakistan. For measuring the level and environmental mining sustainability nature to Environmental Impact Assessment (EIA) of the world’s second largest salt mine “Khewra,” Folchi and Phillips environmental sustainability mathematics (PESM) models are applied. The results indicated that Khewra was deemed to be potentially sustainable for the environment and quality of salt. The results suggest the delicate balance of maintaining sustainability successfully, regarding the mining process in Pakistan which has been affecting the local environment and community so badly. The paper lays emphasis on the potential significance of the model’s application for the attainment of sustainable mining goal. This study is essential for researchers,

May 11, 2020