Search Documents

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2013

By E. L. McHugh, R. T. Mayerle, J. M. Girard

Ground control problems at surface mining operations can occur for a variety of reasons. Stress, gravity loading, rock strength, geology, pore pressure, weather effects, underground workings, and many other factors contribute to slope instabilities that range from small rock falls to massive slides of material. While some of these failures can be predicted or controlled by preventive measures, each year many completely unexpected failures occur. Current methods for monitoring generally involve measuring displacements at a few, selected points in and around the suspected area of instability. While most of the displacements along these points will be in a downslope direction, freeze-thaw cycles of water-filled joints, horizontal stresses or pressure, buoyancy in saturated soils, human measurement errors, or other situations can produce deformation in almost any direction, even without any instability in the slope. Determination of which, if any of the observed movements represents a potential hazard is essential. Because of the enormous surface area of many large open-pit mines, several varieties and scales of instability can occur. Small, unexpected rock falls may indeed be more hazardous than a massive failure that involves slow displacement of material over a longer period of time. Complete vigilance to detect all small potential falling blocks is neither feasible nor economical and certainly is not attainable using today's most common point displacement monitoring techniques. As part of an on-going study at the Spokane Research Laboratory, several new methods for monitoring slope instabilities are being investigated. This paper describes the potential adaptation of systems such as interferometric synthetic aperture radar, imaging spectroscopy, and time-domain reflectometry, to slope monitoring and design.

By Paul Gribbon, Julius Strid, Greg Colzani, Jim McDonald

Portland, Oregon’s $370 million West Side Combined Sewer Overflow Tunnel Project has completed the final phase of construction and commissioning. The construction contract, which began in September 2002, was a reimbursable cost plus fixed fee contract that followed a qualifications-based contractor procurement process and apre-construction planning phase. This paper addresses the final results of the contracting method and provides a lessons-learned case history. Specific items addressed include the benefits realized from the contracting method, areas of improvement, final costs compared to the original contract estimates, design changes and schedule impacts, and subcontract management issues.

Jan 1, 2007

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

By John J. Sammarco

The U.S. Bureau of Mines seeks to increase safety and efficiency in U.S. coal mines. One approach is to develop technology for automation of a continuous mining machine. Realization of an autonomous mining machine requires development of subsystems for machine intelligence, navigation-positioning, and computer control. This report focuses on investigation of one subsystem, an onboard heading system, which would be responsible for determining and controlling machine heading. The onboard heading system investigated is a multisensor system to determine machine heading, pitch, and roll. A directional gyroscope provides heading (yaw), fluxgate sensors provide a compass heading, and gravity-referenced clinometers give machine pitch and roll. The system utilizes a dedicated microcontroller networked to an external system of computers. Tram commands, supplied to the network from external computers, are executed by the onboard system. Sensor feedback is employed for closed-loop control of machine heading by controlling pivots and turns. The report discusses operating limitations and error sources of system sensors and presents test results of closed-loop control of machine heading. Results of tests with a mining machine are used to exhibit various sensor shortcomings and to evaluate control of pivots and turns.

Jan 1, 1990

By Johnson N. W

After an unsuccessful transfer from the laboratory to the pilot plant of galena flotation technology which used sodium metabisulphite and ethyl xanthate, laboratory flotation tests were conducted to identify any unusual variables which had a deleterious effect on the position of the lead rougher grade recovery curve for Hilton and Mount Isa silver-lead-zinc ores. Two variables (pulp temperature and contact time for ethyl xanthate and sodium metabisulphite) had important deleterious effects.The findings allowed a successful transfer of the laboratory process to a pilot plant scale process. The effect of temperature was important because the higher temperature (40°C) in the pilot plant pulp increased significantly the rate of reaction between ethyl xanthate and sodium metabisulphite. In the laboratory process at 20 to 25°C, the reaction rate was lower and did not interfere significantly with the process. The contact time for the two reagents was also important in the pilot plant scale process because of the higher reaction rate at 40°C.To employ ethyl xanthate in the pilot plant process, special precautions were required. Further, a collector (Aerofloat 241) from the dithiophosphate family was used successfully in the pilot plant process.

Jan 1, 1988

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By Drupad B. Desai, Bruce Chang, Jay L. Merritt

This paper reviews difficult ground conditions encountered along the alignment of large-diameter sewage tunnels for the City of Los Angeles. It offers a detailed one-of-a-kind solution to a unique problem for shallow urban underground tunnels in a seismic zone, using state-of-the-art materials, technology, and equipment. The following topics are discussed in detail: • Geotechnical Design consideration for tunnel traversing through an active fault zone. • Seismologist evaluation of possible fault-offset problems where a fault zone crosses the alignment, in the event of an earthquake of moment-magnitude 6.5. • Probability analysis regarding "recurrence interval." • Structural design of tunnel subjected to displacement, subjected to axial elongation or shortening, and capable of rotational freedom. • Special joint details.

Jan 1, 1989

By J. M. Davidson, F. Fraas, J. E. Conley

"A number of Reports of Investigations pertaining to the extraction of potash from cal¬cined polyhalite have been made by various members of the Nonmetallic Minerals Experiment Station of the United States Bureau of Mines. These reports describe results obtained in the study of samples of polyhalite (2CaS04.K2S04.MgS04.2H20) from deposits of possible com¬mercial importance in Texas and New Mexico.3Storch and Clarke6 in their initial paper presenting data on the properties of Texas polyhalite demonstrated the desirability of calcination and subsequent hot extraction with water as a satisfactory pronedure for treatment of this potash-bearing salt. Their preliminary data have been supplemented by an additional report7 dealing more particularly with the leaching of raw and calcined polyhalite with water and with saturated sodium chloride solu¬tions. Further data8 have been reported as a result of experiments made in a small labora¬tory rotary-tube furnace under various calcination and extraction conditions. Hot water was used as the leaching solution in all of these tests.In addition to the data on calcination and extraction, two processes as proposed by Storch and Clarke have been published by Wroth,9 and more recently a number of very promising processes have been proposed by Storoh and Fragen.10"

Apr 1, 1932

By Lottrey A. L, Sowerby B. D, Cutmore N. G

On-line monitoring of low rank coal quality during input to a process has the potential to provide benefits through: ò anticipation of coal quality variations prior to utilisation; ò provision of a tool to help determine the influence of coal quality on process behaviour, and ò provide a direct measure of coal quality for pricing. Moisture and ash are the two most significant coal quality parameters for combustion. They determine the energy content which can be derived from the coal and the problems arising from the presence of ash in the process (eg ash fouling, corrosion, erosion, particulate emissions and ash disposal). Extensive pilot-scale testing and full-scale experience has shown that specific coal/ash constituents (eg Na2O/ash ratio, acid-soluble aluminium, silica, sulphur contents, etc) are also important for the behaviour of Latrobe Valley brown coal during combustion, ash formation, deposition and removal of ash in precipitators and furnace ash hoppers. This paper discusses the range of on-line analysis techniques which have been investigated and their application to low rank coal analysis. Preliminary results from a joint SECV/CSIRO project which aims to develop two separate advanced instrument systems are also presented. These systems are based on: ò microwave attenuation and phase shift - for direct determination of moisture content; and ò inelastic neutron scattering - to provide total hydrogen, carbon, chlorine and ash contents, with potential for calculation of moisture content, specific energy, sodium content and Na20/ash ratio using correlations.

Jan 1, 1992

By J. Bleeck, G. Mahrt

INTRODUCTION Many excellent papers have been written and presented regarding agricultural lime and the subject has been covered extensively in books concerning soil science, fertilizing, limestone, etc. We felt challenged to construct a paper that wouldn’t merely be a repetition of past presentations. Therefore, we chose to begin with factors having the most impact on plant growth realizing that the audience is likely to be relatively unfamiliar with this subject. So, we decided to dig deep into the roots of soil and plant growth science in order to better understand the significant role of limestone in this important area. The soil with the higher plants growing upon it forms an open and dynamic ecosystem in which there is flux of energy and material (heat, light, water, nutrients, mineral and organic matter, organisms). Plants root in the soil and then take up oxygen for root respiration, yielding energy for nutrient uptake, water for turgescence and transpiration and use in photosynthesis and the mineral nutrients needed for the synthesis of organic matter. Above the ground the plant takes in light energy and heat using them in photosynthesis to assimilate atmospheric CO2. Photosynthesis is the basic life process of creation. However, we will look at the root room where soil, water, air, and heat economy and the supply of nutrients determine soil fertility and the important role lime plays here. Location is the primary point to be considered when discussing agriculture (climate and soil); secondly, the dynamic and mobility of the minerals (plant nutrients) in the soil; and thirdly the conversion of organic substances into humus. And then there is a great deal of water involved in the growing process. In order to produce 1 kg of dry plant substance, 300 to 800 kg of water must be pumped through the plant and is then lost by transpiration. Cereals, vegetables, and sugar beets consume between 400 to 500 kg of water during the growing process and long-growing crops, such as alfalfa and clover, can consume 600 to 800 kg of water per kg of finished product. Without water, a plant cannot grow. (Reference 1)

Jan 1, 2006

By B M. Washington, R R. Lovel, G J. Sparrow, M J. Fisher-White

"Work in CSIRO with several Australian ores has shown that?by heating a high-phosphorus goethitic iron ore and then leaching with caustic or acid, the phosphorus levels in the ore can be lowered to a commercially acceptable value of around 0.08 weight per cent phosphorus (P). With increasing heating temperatures up to 1300¦C, the extent of phosphorus removal increased. This is considered to be associated with mineralogical changes in the iron oxide phases in the ore during the heating.Little phosphorus was removed from four high-phosphorus goethitic iron ores containing 0.12 - 0.16 weight per cent P in leaches with boiling water. However, leaches with sulfuric acid removed ten to 20 weight per cent of the phosphorus and leaching with sodium hydroxide removed even more phosphorus to produce leach products containing between 0.08 and 0.12 weight per cent P from three of the ores.After heating at 300¦C, leaches at a low pulp density of 0.5 weight per cent solids with 1 - 5 M NaOH and 0.1 - 1 M H2SO4 gave leach products with 0.06 - 0.09 weight per cent P. The lixiviant concentration required and extent of phosphorus removal depended on the ore. At a higher pulp density of 25 weight per cent solids, leach residues with between 0.07 - 0.14 weight per cent P were obtained.More phosphorus was removed from ores heated at 900¦C. Leaches at both the low and high pulp densities, with 1 - 5 M NaOH and 0.1 - 1 M H2SO4, gave leach products with 0.05 - 0.09 weight per cent P. However, the lowest phosphorus levels were obtained after heating the ores at 1200 or 1300¦C and leaching with 1 M NaOH or 0.1 M H2SO4. Leach residues with 0.02 - 0.06 weight per cent P were obtained, even from leaches at the higher pulp density of 25 weight per cent solids. Leaching tests on heated samples under heap leaching conditions at ambient temperatures have shown that phosphorus levels can be reduced to similar levels to that achieved in an agitation leach within ten days.CITATION:Fisher-White, M J, Lovel, R R, Sparrow, G J and Washington, B M, 2013. Effect of temperature on removal of phosphorus from Australian Goethitic iron ores, in Proceedings Iron Ore 2013, pp 373-380 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962

The Physiographical Features of the Region The Middleback; Range proper, from the Iron Duke in the south to the Iron Prince in the north, extends in a meridional direction for 21 miles, but may well be taken to embrace also the Iron Knob and Iron Monarch prominences so that the total length of the Range is 37 miles.Although no great altitudes are reached, the slopes of the high country are steep and the Range stands out prominently above the peneplaned surface of upper Eyre Peninsula. The Range is built up of sub-parallel ridges at some places, and its continuity is interrupted by transverse breaks or gaps resulting from normal stream erosion and corrosion during earlier periods when precipitation was heavier and streams were more active. Traces of high-level gravels remain on the flanks of Kimba Gap. A former mature stream on the western side of the Range has had its lower reaches blocked by sand and the old stream channel has been converted into an eiongated basin of internal drainage. The sand dunes in this area appear to be practically stationary at present, being fixed by mallee vegetation. Their trend is west-northwest.The relief of the Range is regarded as having been determined primarily by meridional strike faulting and selective silification of some of the beds. Dip faulting on the Iron Duchess leases has produced subsidiary features only.The Rocks of the Region: In order that some of the points made in the discussion of the genesis of the ore bodies may be appreciated it is necessary to consider the stratigraphical succession and the igneous types represented. This classification may be...

Jan 1, 1949

By T. P. R. de Jong, H. Harbeck

"This contribution reports recent mineral sorting experience and lists the opportunities of the newest generation of automatic sorters with a special focus on electromagnetic detection and Xray transmission. With the available sensor resolutions and actuator systems that are available today sorting of minerals down to 2 mm size and up to 250 mm lump size is technically feasible. In industry, ore as well as coal is still hand-picked and current automation potential only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs.They are:??High speed and high resolution sorting systems based on X-ray transmission imaging??High speed on-line image processing and further development of advanced data processing??Modular multi-sensor automatic sorting units (using one or more sensors such as colour, electromagnetic and X-ray in a single device)??Sensitive electromagnetic sensors for sorting based on differences in magnetic susceptibility and electric conductivityThe above enables compact dry separation, insensitive for moisture fluctuations and at high separation sharpness, as well as “electronic” high gradient magnetic separation for larger particles. Besides conventional X-ray transmission (XRT), dual-energy XRT (DE-XRT) is now being redesigned to meet the requirements of the mining industry. The mentioned technologies provide automatic dry separation of minerals and rock as alternative for conventional processing."

Jan 1, 2005

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

By E. Sirolli

In recent times, with rare exceptions, most economically viable ore discoveries have been large, low-grade and located in remote parts of the world. Mining companies have often shown to be incapable of mitigating their social and economic impact on local communities. Sustainable development and relations can be achieved by implementing bottom-up methodologies to the top-down tools already in use by mining companies. In order to magnify the importance of enterprise facilitation as a primary method for community development, data from 25 years of community based work around the world was used. Results highlight the need for a grassroots approach to local economic and community development, which focuses on the creation of a parallel economy in communities. Using solely top-down methodologies for developing community relations is shown to be a limited resource for mining companies. There are fundamentally two dangers for mining companies: alienating the local population, resulting in militancy and lengthy legal battles to obtain a license to operate; and, being accountable for building social and economic infrastructure that are not the company?s responsibility.

Jan 1, 2012

By M Passmore, N Poznik

Olympic Dam is a world-class deposit and is unquestionably one of the most geologically, structurally and texturally complex orebodies in the world. As development advances into the Southern Mine Area (SMA) the geological understanding is rapidly evolving as underground drill rigs are prioritised to provide the additional data necessary to convert Indicated and Inferred Resources into Measured Resources. The SMA represents approximately 70 per cent of Olympic Dam’s total resource and is significantly more complex when compared to the Northern Mine Area with respect to the diverse nature and origin of lithotypes, rock mass characteristics and the extent of major structures controlling primary mineralisation trends.Recent mine development into the central SMA has been impacted by a major structural gouge zone. Sound geological interpretation allowed mine geologists to successfully integrate their local understanding of the distribution of lithotypes with critical geotechnical data, chiefly rock quality designation (RQD), to delineate and better predict this major structural gouge zone. As a direct result, development rates improved whilst also increasing awareness for the importance of sound geological interpretation utilising all available data. In order to maximise predictability across all systems in place through the mining geology value chain, the integration of geological and geotechnical data in a geotechnical RQD block model provides an additional tool to assist in preventative solutions for complex problems to achieve a proactive mining environment.This paper details the methods used to build the RQD block model, the geostatistical estimation parameters, 3D geotechnical domain wireframes, challenges regarding legacy approaches, and collection of geotechnical information and incorporating/linking geotechnical data with geological features, including the use of grade and lithotype domains. Although the geotechnical block model proved difficult and complex to construct, the resultant product has seen successful integration of geological and geotechnical data into mine planning providing higher resolution of critical parameters for local mining areas.CITATION:Clark, J M, Passmore, M and Poznik, N, 2017. Olympic Dam rock quality designation model – an integrated approach, in Proceedings Tenth International Mining Geology Conference 2017, pp 27–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017