Search Documents

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By L. H. Banning

Recent dry-top electric smelting tests at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., indicate that a high-titanium slag and a good grade of pig iron can be produced from alluvial Idaho ilmenite. A total of 120 tons of concentrates were smelted during this investigation, to yield an average of 0.5 ton of slag and 0.3 ton of pig iron per ton of ilmenite. Power consumption averaged 1,400 kv.-hr. per ton of ilmenite, at a feed rate of 400 to 500 pounds per hour, when operating at an electrical energy input of 290 to 370 kilowatts. The optimum operating voltage appeared to be 110 volts, phase-to-phase. Graphite electrode consumption averaged 15.6 pounds per ton of ilmenite smelted. Magnesite furnace refractory withstood the corrosive action of the hot metal and slag better than carbon refractory.

Jan 1, 1955

The Mineral Sector Development Project, sponsored by the World Bank, has been set up to revise the legal, regulatory and fiscal framework for the minerals industry in Tanzania, with a view to attracting mining companies and investors to the country and facilitating future minerals development. One component of this project, the Environmental Management Framework for the Mineral Sector, was awarded to Wardell Armstrong of the UK and ENV Consult of Tanzania. In developing a new framework of environmental regulations, emphasis was placed on developing realistic standards which reflect local conditions and prevailing values. The main corner-stones of this approach are; effective environmental impact assessment procedures; establishment of environmental management procedures; and monitoring and auditing of companies? performance. The favoured approach involves a three-tier framework, as follows: ?Framework environmental provisions within the new Mining Act; ?Regulations covering more detailed environmental requirements ?Guidelines and/or Codes of Practice, which may in future become regulations in their own right. Careful consideration has been given, in developing the framework, to the limited resources likely to be available for implementation to the Ministry of Energy and Minerals and this has influenced the approach that has been adopted. This paper outlines the main components of the environmental management framework and discusses some of the important issues raised by these proposals.

Jan 1, 1998

The Beginnings of Mineral Processing Research in Canada - A Short Account

Sep 13, 2010

By Mwaba CC

Ok Tedi Mining Ltd has been using flotation for the production of copper/gold concentrates from a complex copper sulphide ore for several years. During this period, much effort has been devoted to metall- urgical treatment of the ore. This paper examines some of the mineralogical aspects of the sulphide minerals in the ore using the electron microprobe analyser. Results have revealed the complexity of the copper sulphide minerals and in particular, chalcocite. Analysis of both plant and laboratory flotation products has provided further insight into the effects of mineralogy on the flotation of copper and iron sulphides. A significant observation is that some of the pyrite minerals apparently exhibit natural floatability. The implications of the mineralogical characteristics of the sulphide minerals on the flotation of the ore are also discussed.

Jan 1, 1991

By P. C. -H. Rhee, H. -G. Lee, J. -H. Choi, D. S. Kim, S. -B. Lee

In order to predict the composition of inclusions and to ascertain a method to prevent inclusions from forming in liquid Fe-16 mass Cr alloy, a thermodynamic database was developed through a quantitative determination of thermodynamic relationships of Cr-Al-Si-Mn systems in the liquid Fe alloys. Applications of the databases to the prediction of Mn/Si complex deoxidation with Alin Fe-16 mass Cr alloy were demonstrated in succession. The electromagnetic levitation technique using a cold crucible was employed to separate inclusions from liquid metallic alloys completely and to prevent any contamination from surroundings. Various interaction parameters in the liquid Fe-16 mass per cent Cr alloy system were determined; these are: [eAl(Fe)Cr= 0.19/T, rAl(Fe)O,Cr= -0.01, rAl(Fe)O,Cr= -0.00013, eS1Cr(Fe)= -0.38/T,rSi(Fe)O,Cr= 0.007, rO(Fe)Si,Cr= 0.0044, rA1(Fe)Si,Cr= -0.0075, rSi(Fe)A1,Cr= -0.0078, rSi(Fe)Mn,Cr= 0.005, and rMn(Fe)Si,Cr=0.01.] An improved database, utilizing interaction parameters for molten metal determined in this study, and the Fact Sage slag database of the MnO-SiO2-Al2O3-CrOx-MgO system were used for thermodynamic calculations. These were carried out under various thermodynamic conditions, and results were compared with experimental data of Si/Al, Mn/Si, and Mn/Si/Al deoxidation equilibria. With the abovementioned results, together with experimentally obtained data, thermodynamic conditions were determined, in particular Mn and Si contents, under which liquid inclusions form in liquid Fe-16 mass per cent Cr alloy. The critical Al content in liquid Fe-16 per cent Cr alloy, above which solid inclusion of corundum phase ((Al,Cr)2O3) formed, was as low as 10 ppm. This indicates that extreme care must be taken in controlling the Al content in the metal to avoid formation of solid corundum phase ((Al,Cr)2O3) inclusion. The compositional change prediction of inclusions, which originate from slag entrapment and by Ca addition, was demonstrated by use of the alloy database optimized through this study, and the Fact Sage oxide database. For Si-deoxidized Fe-16 per cent Cr alloy, high Si and low basicity of slag are effective to obtain liquid inclusions. For Al-deoxidized Fe-16 per cent Cr alloy, it is important to keep the Si content lower than 0.1 per cent and it is required to add Ca. Keywords: inclusion, thermodynamic simulation, deoxidation, Fe-16 per cent Cr alloy,stainless steel, interaction parameter, cold crucible

Jan 1, 2004

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By Carl Lee

CHICAGO in the last week of June fulfilled all its promises to the visiting engineers except one. This holds true with respect to the activities of the Regional Meeting of the A. I. M. E. in particular and of Engineers' Week in general. No one expected to find much of the beautiful in the outward aspects of the Fair-the Century of Progress Exposition, to be more formal; but they expected novelty, color, and startling lighting effects at night, and they were in no sense disappointed. It has been said that the architecture is a portent of the style of the buildings of the future; most who have seen the Fair hope that this forecast will prove inaccurate. As to the exhibits themselves, they are splendid. They are in keeping with the theme of the Exposition-a Century of Progress in science, in engineering, in the industries based upon them. No attempt will be made here even to suggest the exhibits that are most interesting. There are plenty for every one; and any member of the Institute who has the opportunity should by all means visit Chicago before the end of October.

Jan 1, 1933

Trans. No. Place Date Vol. Page 1. Wilkes-Barre Pa......May.71 1 3 2. Bethlehem, Pa.........Aug., '71 I 10 3. Troy, N.Y............Nov..: 71 1 13 4. Philadelphia, Pa........Feb., 72.. 1 17 5. New York. N. Y.*......May, '72.. 1 20 6. Pittsburgh. Pa.........Oct..' 72.. 1 25 7. Boston, Mesa..........Feb., '73.. 1 28 8. Philadelhia, Pa.*......May, '73.. 2 3 9. Easton, is............Oct..' 73.. 2 7 10. New York, N. Y.......Feb..' 74 . . 2 11 11. St. Louie. Mo.*........May,' 74 . . 3 3 12. Hazleton, Pa...........Oct., '74.. 3 8 13. New Haven Conn......Feb., '75.. 3 15 14. Dover,N.J.*..........May, 75.. 4 3 15. Cleveland,O...........Oct. 75. 4 0 16. Washington D. C......Feb.'' 76.: 4 18 17. philadelphia, Pa.......June,: 76.. 5 3 18. Philadelphia Pa........Oct 76.. 5 19 19. New York, N. Y.......Feb: '77.. 5 27 20. Wilkes-Barre. Pa.*.....Mag :77.. 0 3 21. Amenia N. Y..........Oct. 77.. 6 10 22. Philadeiphia Pa........Feb.;' 78. . 6 18 23. Chattanooga' Term.*. . . May' 78. . 7 3 24. Lake George: N. Y....: Oct. 78. . 7 103 25. Baltimore, Md.*.......Feb:' 79.. 7 217 26. ~ittsburgi, Pa.........~a;' 79.. 6 3 27. Montreal, Canada......~ept.;' 79.. 8 121 28. New York, N. Y.*......Feb., '80.. 8 275 29. Lake Superior, Mich....Aug., '80. . 9 1 30. Philadelphia, Pa.*......Feb., '81. 9 275 31. Staunton, Va..........May, '81. .10 1 32. Harrisburg, Pa.........Oct.. '81..10 119 33. Washington, I). C.*....Feb., '82. . 10 226 34. Denver. Colo..........Aug.. '82. . ll 1 35. Boston. Mass.*.........Feb.. '83..11 217 38. Roanoke, Va...........June, '83.. 12 3 37. Troy, N. Y...........Oct.. '83. .12 175 38. Cincinnati. O.*.... Feb, '84..12 4 39. Chicago Ill............May, '84. . 13 1 40. philadelphia, Pa........Sept., '84. . 13 285 41. New York, N. Y.*......Feb., '85. . 13 586 42. Chattanooga, Tenn.....May, '85..14 1 43. Halifax, N. S..........Sept., '85.. 14 307 44. Pittsburgh, Pa.*........Feb.. '86 . . 14 587 45. Bethlehem. Pa.........May, '86 .. 15 Ixiii. 46. St. Louis, Mo..........Oct, 86.. 15 Ixx. 47. Scranton, Pa.*.........Feb.', '87. . 15 lxxvi 48. Utah and Montana.....July '87.. 16 xvii. 49. Duluth, Minn...........July' '87. -16 xxiv. 50. Boston. Mass.*.........Feb.: '88. . 16 xxviii. 51. Birmingham, Ala.......May, '88. .17 xix. 52. Buffalo N. Y..........Oct. '88.. 17 xxiv. 53. New york, N.Y........feb.' ;89 . . 17 xxxi. 54. Colorado..............June' 89 . . 18 xvii. 55. Ottawa, Canada........Oct., 89. . 18 xxiv. 56. Washington, I). C.*. . . Feb. 90. .18 xxx. 57. New York, N. Y........sept:, '93. .19 vii. 58. New York, N. Y.*......Feb. '91. . 19 xxv. 59. Cleveland, O.......... June, :91 . .a xvi. 60. Glen Summit, Pa.......Oct, 111. . 20 lxi. 61. Baltimore, Md.*.......Feb.: '92. .21 xix. 62. Plattsburg, N. Y.......June, '02. . 21 xxxiii. 03. Reading. Pa...........Oct., :92. .21 xliv. 64. Montreal. Canada*.....Feb. 93..21 65. Chicago, Ill............aug.: '93..22 XI. 66. Virginia Reach. Va.*. ...Feb., '04. .24 xwl. 67. Bridgeport Coon.......Oct., '94..24 xxx?. 08. Florida ...'............Mar., '95. .25 xix 69 Atlanta. Ga......... Oct 95. 25 xi 70. Pittsburgh. Pa.*........Feb., '96.. 26 xvii. Trans. No. Place Date Vol. Page 71. Colorado..............Sept. '96. .26 xxix. 72. Chicago, Ill............Feb.. "97.. 27 xvii. 73. Lake Superior..........July '97. .27 xxx. 74. Atlantic City, N. J.*. ..Feb.: :98. .28 xvii. 75. Buffalo N. Y..........Oct. 08. .28 XXXVI. 76. New York,N. Y.*......Feb.: '99. .29 xvii. 77. California.............Sept., ;99. . 29 xlix. 78. Washington, D. C.*.....Feb., 00. .30 xix. 79. Canada...............Aug.. '00. .30 xlv. 80. Richmond. Va.*........Feb.. '01. . 31 xix. 81. Mexico................Nov..'01.. 32 cxviii. 82. Philadelphia Pa. $......May, :02. . 33 xxxv. 83. New Haven, Conn......Oct.. 02.. 33 xlvii. 84. Albany N. Y.*........Feb '03. .34 xxiii. 85. New York, N. Y........Oct.': '03. .34 xi. 86. Atlantic City. N. J.*....Feb., '04. .35 XXIII. 87. Lake Superior..........Sept.'04. .35 dii. 88. Washington. D. C......May' '05. .36 xlii. 89. British Columbia.......July, '05. . 36 90. Bethlehem. Pa.........Feb. '06. .37 xli. 91. London, England.......July: '06. .37 xlviii. 92. New York, N. Y........April, '07. . 38 lii. 93. Toronto, Canada.......July. '07. .38 lix. 94. New York, N. Y........Feb., :08. .39 xli. 95. Chattanooga, Tenn.....Oct.. 08..39 xlviii. 06. New Haven Conn......Feb. '09. .40 xli. 97. Spokane,Wash.........Sept:.'09. .40 xlviii. 98. Pittsburgh, Pa.........Mar.,'10. .41 xxxviii. 99. Canal Zone............Nov.,'10. .41 dv. 100. Wilkes-Barre, Pa.......June. ' 11. . 42 xxxiv. 101. San Francisco, Cal......Oct.. '11..42 xliv. 102. New York. N. Y.*......Feb 12. .43 Ixxvii. 103. Cleveland, Ohio........0ct;' '12.. 44 wii. 104. New York, N. Y.*......Feb.. '13. .45 xv. 105. Butte, Mont...........Aug., '13. .46 ?' 108. New York, N. Y........Oct., 13..47 vii 107. New York. N. Y.*......Feb.. '14..48 xv. 108 Salt Lake City. Otah Aug. :l. 49 5: 109. Pittsburgh, Pa.........Oct., 14. .50 vii. 110. New York, N. Y.*......Feb., '15. .51 xvi. 111. San Francisco, Cal......Sept., '15. .52 xii. 112. New York,N. Y.*......Feb., '16..54 xvi. 1 Arizona...............Sept.,'l6. .55 VII 114. New York, N. Y.*......Feb., '17: .56 vii. 115. St. Louis, Mo..........Oct.. '17..57 vii. 116. NewYork,N. Y.*......Feb.. '18..59 xvii 117. Colorado.....:........Sept.,'18. .60 vii. 118. Milwaukee, Wis........Oct.. '18. .60 x:!: 119. NewYork,N. Y.*......Feb., '19..61 xi. 120. Chicago...............Sept.,' l9.. 62 VII. 121. New York, N. T.*......Feb., '20..63 ix. 122. Lake Superior District. .Aug., '20.. 66 ix. 123. New York, N. Y.*......Feb., '21. .66 xiii. 124. Wilkes-Barre, Pa...... Sept.. : 21.. 66 xix. 125. New York, N. Y.*......Feb., 22. .67 ix. 126. San Francisco. Cal......Sept.,:22. .68 xxix. 127. New York, N.Y.*.....Feb., 23. .69 xxix 128. Canada...............Aug., '23. .69 xxxv! 128.129. New York, N. Y.*......Feb., ;24. .70 xxxi. 130. Birmingham, Ala.......Oct. 24. .71 xxxiii 131. NewYork.N Y.*......Feb.: '25.. 71 xxxviii. 132. 131.Salt Lake City, Utah .. .Sept., '25. .73 xvi 133. New York, N. Y.*......Feb., '26. .73 xxii. 134. Pittsburgh Pa ....... Oct.. '26. .74 xv. 135. New York,' N. Y.*............Feb., '27. .75 x::: 135.136. NewYork,N. Y.*......Feb., '28..76 104 137 NewYork.N. Y.*......Feb., '29. .291 116 138.San FranciscoYork,N.Y. Cal..........Oct. 29..308 406 139. New York, N. Y.*...Feb., '30..30H 1321

Jan 1, 1930

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in plane-polarized reflected light, colour changes are observed which are characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film!coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins. Bituminous coal gave the best results.

Jan 1, 1970

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

A systematic study of groundwater conditions at eight underground mine sites exhibiting a wide range of groundwater qualities throughout Australia has been completed at the WA School of Mines. This has resulted in a new corrosivity classification for groundwater driven corrosion processes for cement grouted cable strand used in the Australian underground mining industry. The new corrosivity classification is simple to use and corrosion rates may be predicted from readily obtained in situ measurements of groundwater dissolved oxygen.

Jan 1, 2008

Uranium exploration over a wide area of the Southern Frame Embayment, South Australia, has defined a number of Lower Tertiary fluvial palaeochannels incised in older rocks. The buried channels contain similar stratigraphicsequences of interbedded sand, silt, and clay, probably derived from the adjacent uranium-rich Olarv Provinee. Uranium mineralization is pervasive within two major palaeochannels, and four small uranium deposits have been found in the basal sands of these channel sequences, at the margins of extensive tongues of limonitic sand.One of the channels is examined in detail with respect to channel morphology, stratigraphy, and rock alteration and the geology and ore controls of the contained uranium deposits are described.A geochemical zonation reflected by variation in limonite, pyrite, carbon, and humic malleI' is defined across one of the deposits. A genetic model is proposed suggesting formation by a uraniferous geochemical cell which migrated down the stream gradient and concentrated uranium on its lateral margins adjacent to the channel bank.

Jan 1, 1978

By P G. Self, M D. Raven, R A. Eggleton

Investigation of an abandoned quarry near Rowland Flat in South Australia identified asbestiform antigorite as the fibrous serpentine mineral mined during the 1940s to 1978 for filler applications, not amphibole asbestos or chrysotile as reported in earlier investigations. Scanning and transmission electron microscopy (SEM and TEM) and selected area electron diffraction (SAED) of individual fibres were used to confirm the identification. Chrysotile is widely regarded as the only asbestos mineral in the serpentine group. Further work was done therefore, on the geology and mineralogy of the occurrence, and the health implications were reviewed. A zone of antigorite alteration, with associated talc, is traceable for 750 m along strike of recrystallised dolomitic siltstone within Woolshed Flat Shale of Neoproterozoic age. The antigorite formed, in part, by replacement of prismatic crystals of probable tremolitic amphibole. The deposit is proximal to the Williamstown Fault and the serpentine-talc alteration is possibly due to fluids expelled along the fault during late-stage deformation in the Early Palaeozoic Delamerian Orogeny. The antigorite comprises white to pale green bundles of lath-shaped fibres that occur either as randomly- arranged equant patches after amphibole or as cross-fibre veins, both intimately mixed with calcite. Highly fibrous product was mined from the weathered zone where calcite was leached during weathering. Gentle grinding releases fibres with a high aspect ratio (>10:1) that show a wide range of fibre thickness, including a significant proportion of fibres <0.25 ¦m width. Toxicological studies on fibrous antigorite from Poland and Italy indicate that the carcinogenic potential of this form of serpentine is similar to amphibole asbestos. X-ray diffraction (XRD) and fourier-transform infrared (FTIR) techniques readily distinguish antigorite from chrysotile. Determination of asbestiform habit and confirmation of antigorite mineralogy is most reliably done using electron microscopy, preferably with SAED capability.

Jan 1, 2008

By Robert Harris, David Duncan

The Samira Hill gold mine represents the first commercial gold project for the landlocked country of Niger in West Africa. It began production in October 2004 as the result of over 10 years of exploration and development work. There were several administrative, social and technical challenges that had to be overcome to realize the successful development of the project. The Samira mine is located on the geological structure known as the ‘Samira Horizon’ which is developing as a promising district for additional discoveries and other mine developments.

Jan 1, 2005

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

By D. van Rensburg

Jointed rock slopes are generally stable, as there is no freedom of movement for blocks of rock. In an open- pit mining environment, blasting opens up space into which blocks of rock can fail, resulting in the common occurrence of slope failure. Prior to the blasting of a trim pattern, the immediate highwall is scaled, where loose rock material is removed by means of a mechanical scaler. As mining of the pit progresses, the height of the scaled highwall from the pit floor progressively increases. These highwalls are never scaled again for the remainder of the pit life, and time-dependant deterioration contributes to these highwalls becoming subject to rockfall and, sometimes, slope failure. This paper documents the development of a South African innovation, a remote-controlled mechanical highwall scaler, a world first for the mining industry. The scaler will enable open-pit highwalls to be scaled from crest to toe whenever the need arises. It will reduce the risk associated with highwalls and deliver on the Anglo American promise of producing safe, profitable platinum.

Jan 1, 2012

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

By Donald Leroux, Lori Lynn Smith, Robert Hutchison

"The grinding circuit of the Heath Steele concentrator was sampled under five different sets of operating conditions. The balanced results of the sampling campaigns were used to calibrate steady-state rod mill, ball mill and cyclone models using a commercial simulation software package (JKSimMet® ). Thirteen process variables had the potential to affect significantly the performance of the grinding circuit. Statistical-Design-of- Experiments techniques were applied to plan the suite of simulations in order to improve the quality of and minimize the time to find the optimal solution. The effect of each factor on three performance indices (the cyclone overflow size distribution, the circulating load and the cyclone underflow density) was modeled with empirical polynomial relationships using another software package (Design-Expert@)T. he conditions under which the cyclone overflow size distribution was maximized while respecting circulating load and cyclone density constraints were identified using these relationships. Among the most interesting results is the prediction of a set of conditions where the circuit target size distribution is achieved with only three ball mills instead of four.IntroductionProduction at the Heath Steele concentrator (near Miramichi, New Brunswick) started some 43 years ago at a rate of 750 t/d. The plant capacity was increased to 4000 t/d through successive expansion phases in the seventies (Sapiro, 1977; Johnston, 1978). However, as a result of depleting ore reserves, the plant throughput had to be gradually reduced to the current production rate of 2700 t/d. Heath Steele Mines currently have proven and probable reserves which would see it producing until the end of 1999 (Noranda Inc., 1997).An analysis of the grinding circuit of the Heath Steele concentrator was recently commissioned to identify opportunities for reducing operating costs while maintaining budgeted mill throughput and metallurgical performance. Since the plant will likely be operated below nominal capacity for the rest of its lifetime, the possibility of improving grinding efficiency by operating with fewer ball mills and/or crushers was contemplated."

Jan 1, 1999