Search Documents

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

By Healy T. W, Dixon D. R

The present study 'of pure ZnS and NiS and ZnS (marmatite) by detailed electrokinetic methods has shown that by careful control of experimental parameters much new' information on sulphide-water interfaces can be obtained. Time-dependent processes of alteration of sulphide surfaces are foHowed by electrokinetic methods and indicate that the isoelectric point of the surface depends on elemental sulphur coverage, oxidation product coverage, and the conditions which promote or minimize such reaotions in the presence and absence of activator.

Jan 1, 1977

ALTHOUGH the development of the various flotation processes during the last 8 years has been so revolutionary, this development has been, until recently, entirely confined to the separation of the gangue from the mixed metalliferous sulphides.The desirability of finding some method of separating the independent sulphides from such a miXture, by means of flotation, has long been recognized. ThIS need was emphasized when the slimes resulting from the grinding of Broken Hill sulphide ores were for the first time successfully dealt with by the Mineral Separation Company's process on the Central mine. This process proved the practicability of separating the sulphides of lead and zinc as a mixed concentrate from the gangue present in slime. Although this was a very notable achievement, the process has not been generally used, owing to the mixed lead and zinc concentrates resulting from the treatment being acceptable neither to the zinc nor the lead smelters.Although the introduction of eucalyptus oil in minute quantities as an emulsifying agent has simplified the work of the subsequent tabling of mixed sulphide concentrates, rendering unnecessary the burning off or removal of the oil, there will always be a considerable quantity of slimy product too fine to settle on the moving surface of the concentrating machines, and therefore requiring other means for its division into lead and zinc concentrates.

Jan 1, 1912

By Robert Vergie

Like most of you, I would rather work on a job than talk about it. But it is fruitful to spend some time taking stock of important developments in the heavy construction field. One of the strongest recent movements affecting the industry has been the push for safety. I regret that it is a recent development. Not that builders were against safety. Too often though, it was easier to continue with dangerous old work methods than to try something new. Too often, it was easier for equipment manufacturers to build production tools with little consideration for worker safety. And too often, accidents and gruesome disasters occurred. The ultimate result of on-the-job injuries in construction and other industries was the Federal Government's Occupational Safety and Health Act of 1970. Individual states were required either to accept OSHA or pass updated regulations at least as stringent as the Federal requirements. These new rules must be strictly obeyed -- not just because they carry civil and criminal sanctions -- but because they correct unsafe conditions and reduce hazardous acts. Though some OSHA measures have been criticized as superfluous, most of them do in fact save lives and limbs. Equally important, the tunneler who follows the new safety regulations can be fairly certain of an efficient, uninterrupted operation. Regulations do sometimes bring rewards.

Jan 1, 1974

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By CHARLES R. KETES

I. INTRODUCTORY. INDUSTRIALLY, the most important service that geological science can now render to mining in the Upper Mississippi leadand zinc-fields is to devise some practical scheme whereby the productive ore-belts may be located with greater certainty than they have been in the past. Up to the present time there has been little service of this kind, and in spite of all that has been worked out concerning the geologic features of the region, and notwithstanding all that has been written about these ore-deposits, this particular phase of the subject has been, for some reason or other, the very one that has received the least consideration. The neglect by geologists in this respect has been all but complete. The following notes are suggestive of some practical solutions to the problems presented. As here suggested, the geologic relationships of the ore-bodies were surmised some years ago, though somewhat vaguely perhaps. No opportunity for securing critical data appeared until recent investigations of a private character were undertaken, which bad in view the extensive prospecting of undeveloped areas. Fresh from rather wide experiences of a decade in the principal mining-regions of four continents, and after a lenstrum's residence among the chief mining-camps of the West and of Mexico, under conditions which measured geologic hypotheses in meters and rigidly tested their values in, terms of dollars, the recent return to the Joplin field and a new survey of its ore-conditions were fraught with somewhat unexpected results. Aspects of the ore-deposition were presented of which previously there was no hint. Ten years' absence from the district had tended greatly to clarify former hazy impressions. It enabled many features, then only dimly outlined, to be considered more nearly in their true perspective and in their real relationships to their surroundings. It permitted a great mass of details collected a dozen years before in connection with the work of the Missouri Geological Survey to be viewed under new light and to

Feb 1, 1909

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By Daniel Barkley

Underground coal mining in Illinois has a lengthy history dating back to the early 1800?s. High extraction underground mining has played a significant role in production through out this time. Modern mechanized longwall mining methods were introduced in the 1960?s and have been in continual use ever since. Regulations governing subsidence from underground coal extraction and the mitigation of resulting impacts to surface structures and surface land initiated in 1983. Despite the history of experience with subsidence, recent plans to longwall in Illinois have stirred public emotions and strong opposition. Anti and pro longwall groups formed and divided a community over the potential economic benefits new mining ventures could bring verses the potential problems associated with longwall mining in productive flat farmland. The debate culminated in a county wide referendum vote on the use of longwall mining. This paper provides an overview of the history of underground mining in Illinois, the controversy that has risen in central Illinois regarding longwall mining, and the efforts to educate the public about regulations that govern longwall subsidence.

Jan 1, 2007

During the last 125 years, the steel industry has witnessed revolutionary changes in the process of steelmaking. The Bessemer process was the predominant steel production technology during the last two decades of the 19th century. The open hearth process accounted for the lion's share of world steel production for six decades from 1910 to 1970. With the appearance of the LD process on the industrial stage in 1952, the importance of open hearth process declined and currently the basic oxygen processes are contributing more than 60 per cent of the world steel production. The LD process also led to the development of several other oxygen blown processes such as LDAC, OLP, OBM, QBOP, EOF, Clc.

Jan 1, 1999

By W. J. Grose

The Embankment Place office development over the platforms of Charing Cross Railway Station in London has presented many interesting and unusual problems to the engineers involved with the project. The main structure is supported on widely-spaced columns which penetrate the station platforms and underlying vaults, calling for high capacity foundations built in severely restricted spaces. Hand-dug underreamed piles were chosen. Whilst a conventional design approach was taken to size the piles, a detailed appraisal of ground movements was made to explore the effects of the new building loads on the existing foundations, not only beyond the site perimeter but also those amongst the new foundations. Before construction of the pile proper could take place, it was necessary to sink a caisson through the upper unstable and water-bearing soils. This being identified as a high-risk item, a full-scale trial was carried out prior to embarking on the main works. The twenty-one hand-dug piles were 2.5m diameter, over 30m deep and belled out to between 4.5m and 6.6m.

Jan 1, 1989

By Luiz Alberto dos Santos

Neste trabalho foram usinados CDPs da liga com composição de 50,9 % at de Ni e, em seguida, as amostras foram envelhecidas em temperaturas entre 350-550 ºC, tensões aplicadas de 60 MPa e tempos de 45 e 180 minutos. Além disso, foram realizados também envelhecimento sem aplicação de carga nas mesmas condições de temperatura e tempos para comparação das propriedades, porém acrescentando uma amostra solubilizada a 850ºC durante 1 hora. Posteriormente as amostras foram caracterizadas por DSC para determinação das temperaturas de transformação de fases. Observa-se neste trabalho que o DSC de algumas amostras apresentou tanto no aquecimento quanto no resfriamento dois picos de transformação que pode estar relacionado ao aparecimento da fase R. Além disso, pode ter ocorrido a formação da fase Ni3Ti4, pois ligas com teores acima de 50,6 %at. de Ni são caracterizados pela formação de precipitados ricos em Ni, que pode acarreta na diminuição da concentração de Ni na matriz e aumento da temperatura de transformação. Este trabalho é importante, pois há poucos estudos relacionados com o efeito do envelhecimento sob carga nas propriedades de efeito de memória de forma e superelasticidade da liga NiTi.

Aug 16, 2017

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By Jacob Masliyah, Zhiang Zhou, Tshitende Kasongo, Jianjun Liu, Zhenghe Xu, Jeawon Choung

"Slime coating is a recognized challenge in fine particle flotation, not only in decreasing recovery, but also in reducing the selectivity and hence froth quality. In this presentation, a novel method based on electrophoretic mobility distribution measurement to study slime coatings is described. By measuring electrophoretic mobility distribution of individual minerals and their mixtures, the interactions between these minerals can be evaluated.For illustrative purposes, a model system of fine coals, or oil sands with two different types of fine clays was studied. Flotation tests showed a significant decrease in coal (bitumen) flotation recovery with montmorillonite but not with kaolinite clay addition. When electrophoretic mobility distribution of a fine coal/montmorillonite clay mixture was measured, a single modal zeta potential distribution was obtained, in contrast to a bimodal distribution for fine coalkaolinite clay mixture. This finding suggests a stronger adhesion of montmorillonite than kaolinite clays on fine coal surfaces. In the case of bitumen, the bimodal zeta potential distribution was measured for the mixture of bitumen emulsion and kaolinite or montmorillonite, indicating a weak attraction of the clays by bitumen. In the presence of calcium, however, a single modal zeta potential distribution was obtained in the mixture of bitumen emulsion with montmorillonite but not kaolinite clays. These findings are in excellent agreement with bitumen flotation results, demonstrating that the electrophoretic distribution measurement is a powerful tool to study slime coating phenomenon in a complex fine particle flotation system."

Jan 1, 2002

By D Jensen, L Riffo, S Yu, F Traczyk, D Meadows

With the steady increase of molybdenum demand worldwide and the favorable molybdenum market, many technological innovations on both process and equipment have been developed and applied in many modern molybdenum plants around the world. This paper introduces the most commonly used molybdenum flotation flowsheet, together with the introduction of the flotation chemistry. Many different types of flotation cells are used in modern moly plants, and each type of flotation cell has its own unique advantages suited for particular ore and process conditions. This paper tries to provide some insight and guidelines in flowsheet development and flotation cell selection in the molybdenum plants.CITATION:Meadows, D, Jensen, D, Traczyk, F, Yu, S and Riffo, L, 2013. Molybdenum flotation circuit and flotation cells, in Proceedings MetPlant 2013 , pp 387-398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Alain Blanchier, Gilles Gomez

Neighborhood pressure on quarries has become urgent to deal with quarry managers and operators must apply the most recent technologies and communicate it for long shelf life time exploitation, the quarry in which the work is located in urban or suburban environments needs to take into account blasting rules as well as site environment. The main problems to be addressed are:

Jan 1, 2009