Search Documents

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

Stope back conditions in the cut-and-fill stopes at New Broken Hill Consolidated Limited often deteriorate to such an extent that, because conventional rockbolts are not able to maintain safe working conditions, square-set timber is installed. An attempt to eliminate this costly procedure has involved the use of long grouted rockbolts using high tensile prestressing wire. These bolts were developed in conjunction with the prestressing engineers of BBR (Aust.). This form of support has improved the back conditions, maintained safe working conditions, and delayed the introduction of timber in a number of stopes.Production from these stopes has been maintained at its previous level (at a rate approximately double that of a comparable timber stope).

Jan 1, 1974

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By E Deucker, A White

Gold Fields Australia (Gold Fields) has identified that improving productivity through more detailed shift planning and operational control of mining activities is a key driver to the success of their business. The Hamlet mine was chosen as a pilot site to trial a system that would allow production engineers and shift bosses to align the execution of short-term activities with the longer-term goals of the organisation.Gold Fields partnered with Deswik to introduce an on-site, collaborative, web-based system to allow mine planners to quickly build-up a detailed, activity-based, shift schedule for the coming week from the 13-week plan. Multiple stakeholders could then review and alter the plan, and then track and manage the execution of the activities.The system is designed to be integrated with production data capture systems to allow tracking of progress towards completion for each activity, as well as to plan and monitor the equipment operating in the mine. Integration of systems allowed engineers to use the large quantities of production data being captured to make informed decisions in the operations environment.The system replaced a complex set of spreadsheets that required expert users in Gold Fields to maintain. By capturing the data in a central database, the planning process is transparent and historic data from the execution of activities is available for analysis to improve productivity in the future.The system has ensured that the highest priority and critical path activities for the business are completed at the right time, improving the efficiency of operations.CITATION:Deucker, E and White, A, 2017. Productivity improvement through collaborative shift planning and tracking, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 225–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By Bjöm Böhle

Top-down construction (or cut and cover construction) is providing important advantages when comparing with conventional construction techniques for commercial developments with deep basements, underground car parks or near surface infrastructure and traffic tunnels. Main features are substantially reduced restrictions to surface usage, avoidance of intervention with adjacent property, provision of rigid substructures resulting in minimal deforma­tions and settlements and, last but not least, accelerated construction pro­gramme. The present contribution illustrates the construction method in general and elaborates in detail on the special foundation works for a major urban commercial high rise development requiring a six level basement structure.

Jan 1, 2006

By G. C. McKerrow

"Mr. G.C. McKerrow, Assistant Manager of Noranda Mines and formerly Smelter Superintendent attended the meeting to answer questions as to why smelters imposed penalties for too much zinc in a copper concentrate or too much copper in a zinc concentrate, etc.D.W. Bridges -Mattagami Lake MinesWhat limits do you set on zinc and lead in a copper concentrate?G.C. McKerrow - At Noranda, we allow 5% zinc free and charge 25 cents for every unit above that. For lead, it is 1% free and 25 cents per unit above that. Lead is a much more harmful impurity than zinc because it tends to recycle more in the smelter circuit and creates a greater health hazard in the plant.E. Thornton - Sullivan GroupWHat harm does fluorine do in the smelting process?G.C. McKerrow - Fluorine usually does not occur in harmful concentrations in non-ferrous smelters. Fluorides are present in exhaust gases in the aluminum and phosphate industries. If these fumes escape into the atmosphere, they may settle out on forage grasses in concentrations that are harmful to livestock.Thorton - Sullivan GroupI have asked this question other places and have been told that it is hard on brick linings and causes gold and silver to be lost up the stack.G.C. McKerrow - Almost any volatile constituent in a smelter charge will aid in carrying other metal values. To this extent it may be harmful.E. Thornton - Sullivan GroupMr. Tait mentioned before a smelter where they have a copper-tin ore and they pay for copper, tin, bismuth and silver but object strongly to indium in the concentrate. Why would this be?G.G. McKerrow - 1 can't see why indium would be a serious impurity. It does tend to concentrate in flu dusts and if you get enough of it you can recover it and sell it but I have never heard of anyone putting a penalty on it.Question - I once ran into a small copper mine in Peru that had cadmium in the copper concentrate but no zinc. The copper smelter charged a penalty for the cadmium. Why would this be?"

Jan 1, 1971

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Michele Ashby

The mining industry is facing new risks from peak commodities, the energy and economic crisis and stock market pressures. The Green Mining Industry Initiative is a risk management strategy for the future of the mining industry. Defining the Risks The bad news is peak commodities, energy and economic crisis and stock markets collapsing are the issues that are already hitting everyone?s bottom line and draining the treasuries of every mining company around the world. Higher energy costs are affecting the bottom line more than ever before, which is creating more risk for companies. Mining companies have major land positions around the world and they have major energy needs. Uncontrollable increases in energy costs, increased regulations for diesel fuel emissions and energy intermittencies are costing mining companies more time, money, and man-power, which are cutting into profits and hitting the balance sheet. The good news is, there are practical energy solutions which are off the grid, tried and true methods which can be implemented in a cost-effective manner and will increase profitability and save shareholder values as well as energy security for these companies and their projects. To date, most of the mining resource industry has not yet considered or used other forms of power like clean, sustainable, or alternative energy for their own energy needs. The reasons have primarily been pushback from the mining industry due to beliefs of older technologies in alternative energy, a lack of understanding of the cost advantages long term, and perceptions of environmental relativity.

Jan 1, 2008

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007