Search Documents

By John Songstead

INTRODUCTION The Bunker Hill mine, located at Kellogg, ID, in the Coeur d'Alene mining district, has been a major pro¬ducer of lead-zinc-silver ore since 1887. Since its dis¬covery, it has produced over 25 401 171 t (28 million st) of ore from 20 to 25 veins and ore zones. The mine now covers an area of approximately 1.609 km (1 mile) in length and 0.8 km (1/2 mile) in width and extends from 1097 m (3600 ft) above sea level to 488 m (1600 ft) below sea level. Production is presently at a rate of 1542 t/d (1700 stpd). During 1965, a new stoping method, the Bunker Hill pillar system, was developed to enable the profitable mining of large, low-grade zinc ore bodies. The system was specifically designed to in¬corporate the Atlas Copco T26GH rubber-tired loaders. High productivities were achieved, and the method was adapted for mining the higher grade stopes where large timber square sets are utilized. This results in nearly 100% extraction. GEOLOGY The area encompassing the Bunker Hill mine lies immediately south of the Osburn fault, a major east-west striking, deep-seated strike slip fault which is the dominant structural feature in the Coeur d'Alene district. The Bunker Hill forms a series of veins and mineralized zones which occur as link structures, tension fractures, and breccia zones in folded, interbedded argillaceous quartzites of the Revett and St. Regis formations of the Precambrian belt series. The Rosco ore body is predominantly a zinc ore body above the Cate fault, which is presently known to occur from the 13 level. [elevation 488 m (1600 ft)] to the 1600 level [elevation 304 m (1000 ft) ]. These ore bodies are stringer zones with at least one dominant 1.8 to 4.5 m (6 to 15 ft) wide band of ore. They dip 0.09 to 0.26 rad (5° to 15°) steeper than the local 0.61 rad (35°) dip of the Cate fault, and also deviate 0.26 to 0.52 rad (15° to 30°) in strike from the Cate. Because of the flat dip and fractured weak hanging wall, normal cut-and-fill mining has not proven practical in this ore body. The mechanized timber methods described in the next section and the Bunker Hill pillar system are the mining methods successfully used. MINING METHODS While pillar stoping and mechanized cut-and-fill stop¬ing methods were obviously superior to the widely used timber stoping methods, as far as cost and productivity

Jan 1, 1982

By A. K. Mahto, B. Samanta

"A heuristic model was developed to simultaneously generate the ultimate pit and production scheduling at a mining project. The method consists of a preprocessing step to select a starter pit, the implementation of a genetic algorithm to optimize the pit and schedule of the starter pit, and a network-flow algorithm–based postprocessing operation to finalize the ultimate pit and production scheduling. Applied to an iron ore mine, the model pit and schedule produced a net present value 21% higher than the reference pit and schedule prepared by experienced field engineers.RÉSUMÉ Un modele heuristique a ete developpe pour generer simultanement l’ordonnancement de la fosse finale et de la production dans le cadre d’un projet minier. Cette methode comprend une etape de pretraitement visant a selectionner une premiere fosse, la mise en oeuvre d’un algorithme genetique pour optimiser la fosse et le calendrier d’execution de cette premiere fosse, ainsi qu’une operation de posttraitement basee sur des algorithmes de flux reseaux pour finaliser l’ordonnancement de la fosse finale et de la production. En l’appliquant a une exploitation de minerai de fer, ce modele de fosse et d’ordonnancement a genere une valeur actualisee nette (VAN) superieure de 21 % a l’approche de reference pour la fosse et l’ordonnancement developpee par des ingenieurs de chantier chevronnes. INTRODUCTIONLong-term planning for an open-pit mine involves two important activities: developing the ultimate pit and determining the optimum production schedule. To accomplish this, an ore deposit is discretized into a number of smallsized elements called blocks, which are presented in a 3D block model structure. Because of economic and slope criteria, only a certain set of mining blocks can be extracted from the deposit constituting a pit. During mining, these blocks must be extracted in a specific sequence known as the production schedule."

Jan 1, 2017

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Choon Sunwoo, Chang-Ha Ryu

There are various methods available for the recovery of dimensional stone in open pit quarries. Explosive blasting has more advantages in the economic point of view over the other methods but was not widely used in Korea because owner was concerned about much economic loss when it failed. Several years of efforts have been made in order to develop more effective cutting methods and to spread to the quarries for strengthening the competitiveness in the market. Rock cutting by jet flame and black powder was generally used in the early stage. Black powder was applied to cut the last horizontal plane after forming other vertical planes using the jet flame. Jet flame operation, however, is time consuming and produces excessive noise, and as the result, brings adverse effects on the operator as well as the complaints from the residence adjacent to the quarry. Some mechanical methods such as the slot drill, diamond wire saw or in-situ scale of diamond saw cutting were introduced. Most effective cutting methods using the explosive blasting were developed and applied successfully. Black powder was replaced with the detonating cord. A new air decking technique where plug was not used was developed. This paper reviews the technology for dimensional stone cutting and case study in Korea.

Jan 1, 2003

By L. W. T. Weitzel

"This paper reviews the Falconbridge- SMRQ’s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40 km property strike length. As a result of its remote northern location, other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel-based financial spreadsheet to bring the total plan together. The focus of the paper is to show the complexity of modern mine planning and associated economic modelling of mine processes. IntroductionThe Raglan project is located 1660 km directly north of Quebec at the northern tip of the Quebec Peninsula in Nunavik. The main property is 40 km in length stretching from the Donaldson airport area at the eastern edge of the property to East Lake at the western edge. The Deception Bay port is 90 km north of the main complex/mill situated at Katinniq which lies approximately in the middle of the property (Fig. 1). The mine processes 1 000 000 tpy of ore from both open pit and underground sources. The mill is forecasted this year to produce more than 150 000 t of concentrate grading more than 18% nickel. All personnel and critical cargo are transported to the site via a company-leased 737 jet from Rouyn-Noranda where the main administration office is located. The majority of cargo is shipped to the site via Deception Bay from Quebec and on the return trip, nickel concentrate is shipped back. From Quebec, the nickel concentrate is sent by rail to the Falconbridge smelter in Sudbury and on the reverse rail haul, nickel matte from the smelter is sent to Norway via Quebec."

Jan 1, 2003

By A. J. Kraemer

This report is one of a series dealing with oil-shale-operations in foreign countries visited and studied by Bureau of Mines oil-shale technologists within the past 4 years. Many oil-shale deposits have been discovered in Brazil and studied with various degrees of thoroughness. In this report the major emphasis is upon the oil-shale concessions of Companhia Nacional de Oleos Mineraes, in the River Valley of the State of Sao Paulo, because this oil-shale deposit is one of the most promising in Brazil for large-scale utilization for the manufacture of liquid fuels and other products of oil-shale processing, and because the opportunity was afforded to examine the concession area and to study mining, retorting, and. refining operations on these shales. Results of detailed analyses at the Oil Shale Research and Development Laboratories of the United States Bureau of Mines, Laramie, Wyo., are reported, Analyses and other date dealing with other oil-shale deposits in Brazil have been compiled from many sources. As many data have been reported as could be correlated to indicate the range of variation of the several types of shale end similar material. The oil-shale deposits in Brazil differ widely in size, richness of the shale, and of the oil. Some deposits are situate& more favorably for exploitation than others.

Jan 1, 1950

By Ralph B. S

Bacterial leaching of low grade quartz felspar porphyry copper ore was studied in large-scale laboratory percolation leaching columns.Limitations in the release of soluble copper showed up before fifty per cent recovery, due to occluding precipitates of iron oxides and hydroxides. Precipitates were removed by increasing the acidity of irrigation feed four-fold with respect to sulphuric acid. However, irrigation at low pH (pH 1.5) inhibited copper leaching. Resumption of bacterial leaching at pH2 was achieved by introducing a period of non-irrigation. The results suggest a 'direct' attack by bacteria on the chalcopyrite substrate rather than an 'indirect' ferric-leach mechanism.

Jan 1, 1981

By John A. Herbst, Alexander Potapov, Xiangjun Qiu

"High Fidelity Simulation is a name applied to the use of first principles modeling tools including Discrete Element Modeling (DEM), Computational Fluid Dynamics (CFD) and Discrete Grain Breakage (DGB) to mathematically describe and study processing systems. Over the past few years, significant advances have been made in High Fidelity Simulation applications, particularly as many mineral processors have been drawn to the study and use of DEM of grinding mills for optimization purposes. This presentation provides an introduction to High Fidelity Simulation, with an emphasis on DEM. It will include insights into current applications of these tools including the optimal design (wear and throughput) of mill lining systems and media selection, the analysis and design (flow and efficiency) of the back-end of grate discharge mills. Advantages of full mill simulations versus individual sub-process simulations will be demonstrated for a SAG mill with different discharge system designs.INTRODUCTIONHigh Fidelity Simulation is providing mineral processors with the opportunity to analyze the behavior of mineral processing equipment from a fundamental or microscale point of view. In the past complex phenomena such as tumbling mill grinding had to be analyzed using black box tools such as residence time distributions for transport and classification functions for passage of particles through grates; while breakage had to be analyzed using PBM models who derived their form from theory but required direct measurement of kinetics. Today with the help of DEM, CFD and DGB these can be analyzed at a very fundamental level.The key element of DEM simulation is the application of Newton’s laws of motion to individual objects or discrete elements. Using this simulation method one can describe the position, velocity (both translational and rotational) of all objects and the transfer of momentum to other objects (Mishra and Rajamani, 1992; Cleary, 1998; Nordell et al, 2001)."

Jan 1, 2003

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By Keith Merriam, Jim McDonnell, Peter Radziszewski, Rob Rotzinger, Ian DeHart

"Taseko Mines Limited Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.In the second staged development project, a VTM-1250-WB regrind mill was selected to replace the existing conventional ball regrind mill to achieve a target grind size of 80 % passing 45 µm. In the third staged development project, a second VTM-1250 regrind mill was selected for installation in Concentrator #2, to match the existing Concentrator #1 Vertimill. This resulted in approximately 25% spare regrind capacity in the Concentrator #2 design, complete spare parts interchangeability and potential future expansion capacity to 50,000 t/d with no circuit upgrades.In this context, a study was initiated to assess not only the performance of a Vertimill grinding circuit processing a copper concentrate to a particle size of 80% passing 17 µm but also to provide Taseko’s New Prosperity project specific design information for grinding to particle sizes below 80 % passing 25 µm.The objective of the work described in this presentation was to explore Vertimill ultrafine (sub 100 µm) grinding test methodologies at both the lab and pilot scales, compare the scale-up data with operational data from the VTM1250 at Gibraltar Mines and subsequently apply this information to particle sizes down to 80% passing 17 µm. The presentation will describe the results obtained preceded by a description of the Gibraltar regrind circuit historical operation and operational performance as well as a description of the Vertimill technology.INTRODUCTIONTaseko Mines Limited is a mining company headquartered in Vancouver, British Columbia, Canada. In addition to mining development projects for copper, copper-gold, gold, and niobium properties, Taseko Mines is seventy-five percent owner and the operator of the Gibraltar Mine near Williams Lake , British Columbia. Taseko Mines Limited’s Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.Metso is a leading process performance provider, with customers in the mining, oil and gas, and aggregates industries. It has corporate headquarters in Helsinki Finland, offices in 50 countries and manufacturing facilities on five continents. Amongst other types of equipment and services, Metso designs and manufactures VERTIMILL® (VTM) Grinding Mills."

Jan 1, 2015

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By F. Habashi

The changes that took place in China between 1984 and 2004 are remarkable. Visits were made to universities, research institutes, metallurgical industry, and many cultural centers within five trips during this twenty years period. The impressions of these visits are outlined.

Jan 1, 2007

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By Axel Preusse

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009