Search Documents

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By M. J. McLeod, S. Watters, G. G. Lutes, S. Castonguay

"Gold-bearing mineralization at Anomaly A occurs in polydeformed Ordovician turbidites of the Kendall Mountain Formation of the St. Croix belt in southwestern New Brunswick, and is hosted by WSWtrending, shallow-dipping, brittle-ductile high-strain zones associated with the latest stage of the second of four regional deformation events. Gold-bearing syn-deformational stockwork, massive, and multiply brecciated quartz-sulfide veined zones form irregular pods and sheets up to several meters thick, which contain arsenopyrite, pyrrhotite, pyrite, stibnite, and a variety of rare minerals that are gold-bearing. Mineralized zones are enveloped by locally auriferous, weakly to intensely altered wall rock. Vein paragenesis includes: (1) early (pre- to syn-D2) quartz-chlorite veins that are largely the product of migration of quartz by pressure solution; (2) crosscutting, multiphase, vuggy quartz-sulfide veins that contain most of the gold and are interpreted to be structurally controlled; (3) late, crosscutting, nondeformed, non-gold-bearing veins containing laumontite, chlorite, muscovite, quartz, fluorite, and base metal sulfides. Carbonate-poor alteration associated with zones of gold mineralization is lithology-specific, and appears to reflect overprinting of multiple events. Major elements removed during alteration include Si, Na, Mn, and Mg. The minor and trace elements removed include Co, Li, Sc, and possibly Sr, Ni, and Zn. Minor and trace elements added include Au, Ag, As, Sb, S, and possibly F, Cu, Pb, and Zr. On the basis of proximity, time constraints, and a similar ore mineral assemblage, gold mineralization at Anomaly A is interpreted to be a distal equivalent of the intrusion-related gold mineralization at the nearby Clarence Stream Main zone deposit. La minéralisation aurifère de l’Anomalie A se trouve dans des turbidites Ordoviciennes polydéformées de la Formation de Kendall Mountain, dans la ceinture de Ste-Croix du sud-ouest du Nouveau Brunswick, où elle est contenue dans des zones de déformation fragile-ductile à faible pendage de direction OSO associées au dernier stade du second de quatre épisodes de déformation régionale. Les zones aurifères syn-déformationelles se présentent en forme massive, de stockwork, ou de veines de quartz-sulfure bréchifiées à répétition formant des lentilles irrégulières et des couches de plusieurs mètres d’épaisseur contenant de l’arsénopyrite, de la pyrrhotite, de la pyrite, de la stibine, ainsi que divers minéraux aurifères rares. Les zones minéralisées sont entourées d’une enveloppe de roches faiblement à intensément altérées, localement aurifères. La paragénèse des veines comprend : (1) des veines précoces de quartz-chlorite (pré- à syn-D2) qui sont principalement le produit de la migration du quartz par solution-pression; (2) des veines polyphasées de quartz drusique et de sulfures contenant la plus grande partie de l’or, celles-ci sont considérées comme étant sujettes à un contrôle structural; (3) des veines tardives stériles, sécantes et non déformées contenant de la laumontite, de la chlorite, de la muscovite, du quartz, de la fluorite et des sulfures de métaux usuels. Les zones de minéralisation aurifère sont associées à une faible altération en carbonate contrôlée par la lithologie et semble résulter de la superposition d’événements multiples. Les éléments majeurs perdus durant l’altération sont le Si, le Na, le Mn et le Mg. Les éléments mineurs et traces perdus durant l’altération sont le Co, le Li, le Sc et possiblement le Sr, le Ni et le Zn. Les éléments mineurs et traces enrichis comprennent l’Au, l’Ag, l’As, le Sb, le S et possiblement le F, le Cu, le Pb et le Zr. Étant donné sa proximité géographique, les contraintes temporelles et les similitudes de leurs assemblages minéraux, la minéralisation aurifère de l’Anomalie A est interprétée comme un équivalent distal de la minéralisation aurifère associée aux intrusions du gisement avoisinant de la zone principale (Main"

Jan 1, 2008

By WM. H. RINKENBACH, C. A. Taylor

No complete work on explosives, their constitution and analysis, has hitherto been published. Several books that contain chapte.r;s on analysis do not cover the matter thoroughly. Methods tha;t, manu~ facturers, testing stations, and other . agencies have developed to meet their own requirements have not been made public. The Bureau of Mines has issued four publications 1 - cov:eri:ng special phases of the subject. This bulletin. is not inte.nded to replace those reports, but rather to cover present methods employed 'in the , industry and to include all classes of explosives and the materials used in their manufacture. No sharp distinctions can be drawn between classes of explosives. . Surplus military explosives, for example, may be used for blasting, just as blasting explosives, under some conditions, may be employed for military purposes. Moreover, one class gradually merges into another because of similarity in composition. Explosives are here grouped as dynamites, black powders, propellants, detonators, and primers. Some materials are used in practically all these groups ; others in only one. To discuss all the materials that have been or that may be used and the methods for their identification and quantitative determination is not feasible, but the methods described will probably suggest ways of examining new mixtures.

Jan 1, 1923

By V. I. Lakshmanan

Process Research ORTECH Inc. (PRO), with its in-depth knowledge on cobalt behaviour in nickel matte smelters and its novel mixed chloride hydrometallurgical processing, is developing a hybrid process to enhance cobalt recovery. PRO’s experimental data is compared with plant information on cobalt behaviour in smelters. In final stages of iron rejection in the converters, the thermodynamics of the matte-slag system dictates the undesirable transfer of the cobalt to the final converter slags. This results in much lower cobalt recovery in the product Copper/Nickel matte (<60%) in present copper and nickel smelters. This information is used to transfer cobalt into desired quantity of converter slag. The enriched cobalt slag is subjected to PRO mixed chloride process to recover nickel, and cobalt as high value salts of importance in lithium ion batteries. From a typical converter slag containing 3.5% Ni, 1.5% Co, and 1.0% Cu, PRO leach process extracts 98 % Ni, and 98 % Co, and 99% Cu. Application of this process to enhance cobalt recovery in typical Copper/Nickel smelters is presented. In addition, this will also enhance the Copper and Nickel recovery. Both these aspects are of interest to the Copper, Nickel, and cobalt producers. INTRODUCTION In pyrometallurgical extraction of copper and nickel from sulphide ores cobalt often occurs with copper and nickel. The requirement of cobalt is increasing due to its need in lithium ion cells used in electric vehicles. Therefore its efficient and economical extraction in a form suitable for use in lithium batteries is of great interest at present. In the pyrometallurgical processing of copper and nickel sulphide concentrates the concentrate is smelted to produce a furnace matte, which is then sent for converting to remove the iron to produce iron free (~1% Fe) matte for further processing to copper or nickel matte. The copper/nickel matte is processed for metals recovery by hydrometallurgical or vapo-metallurgical or oxidation – reduction routes to make market products. As shown in Figures 1 and 2 the slags are produced in the smelting step and in the converting steps. The metal losses in smelting are controlled by the oxygen pressure in that step and slag production which is controlled by concentrate grade. The slag produced in the converting step which is carried out at a higher oxygen pressure contains higher level of metals is often returned to the smelting step to increase value metals recovery.

Jan 1, 2019

By J. D. Morgan

Demand for nonfuel minerals depends on the overall state of the economy, which steadily improved each quarter in 1984. New housing starts rose to 1.8 million units. Automakers turned out about 15% more cars (7.8 million) and 30% more trucks (3.1 million) than in 1983. Nevertheless, many domestic mineral operations experienced difficulties in 1984. This resulted from import competition greater use of newer engineered materials, emphasis on multi-unit housing and downsizing of motor vehicles. About 15% of our energy was imported. This in cluded $36 billion worth of crude oil and $22 billion in refined products This added significantly to the overall merchandise trade deficit of $12; billion. On the bright side for mining, coal production rose 14% to 810 Mt (890 mil lion st). Three-fourths o: the coal was burned to generate electricity and more than half of our electricity was derived from coal-burning plants. With the exception of a few large-bulk, low-value raw minerals, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult. Consequently, our nonfuel minerals trade deficit rose 60% to $19 billion, reflecting imports of $39 billion and exports of $20 billion. There were increased pressures from some major segments of the minerals industry for some form of import protection. But President Reagan said, "Our goal is a system of free and fair trade in goods, services, and capital. We will work toward this goal through both bilateral and multilateral trading agreements." The US minerals industry consists of domestic mines, concentrators, smelters, refineries, mineral manufacturing plants, and recyclers. It also includes many wholly- or partially-owned operations in many parts of the world, providing employment and income for US citizens and others as well. Compared with 1983, the value of US raw nonfuel mineral output rose 8%, to $23 billion. The $253 billion worth of goods processed from this crude mineral output was a 14% increase. Major Metals Raw steel production - a major indicator of both material use and mineral production-rose 10%, to 84 Mt (93 million st). This stimulated a 36% rise in domestic iron ore production, to 52 Mt (57 million st), about 98% pelletized. Iron ore imports rose 44%, to 14 Mt (15 million st). Despite the increase of steel production, output remained well below levels of just a few years ago. For example, 1984 production was still 23% less than in 1981. Raw steelmaking capacity remained steady at 122 Mt (135 million st). The industry continued to cite steel imports as a major reason for low domestic capacity. In December, pacts with seven leading steel exporting nations were announced. This is an effort to reduce import penetration to about 18.5% of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 50% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production, at 45 kt (49,500 st), rose threefold. Mine shipments of tungsten, another mineral tied to steel

Jan 5, 1985

By Carlos Frias

The lead-acid battery recycling is a major industrial activity (more than four million tonnes recycled lead per year) that generates large amounts of toxic wastes such as lead slag, mattes and acidic sludge, besides airborne emissions. This is a waste-producer industry that needs a definitive solution to avoid its negative environmental impact and getting a sustainable lead production. That is the principal target of the CLEANLEAD technology, which properly combines both hydrometallurgical and pyrometallurgical routes aiming to get zero-waste production, reducing the use of energy and resources in all phases of battery reprocessing, and consequently, greatly decreasing the operating cost. There will be no toxic emissions to land, water or air, and obtained products are pure lead metal or pure lead oxide, and commercial gypsum instead of waste sludge.

Jan 1, 2006

By E. L. Singleton

This Bureau of Mines investigation was initiated to study and establish some of the chemical and physical characteristics of the condensed Mno-Si02 system. To prevent oxidation of the manganous ion, I atmosphere of purified helium was used in the furnaces. Solidus-liquidus curves and invariant points were established from melting-point determinations and were supplemented from data obtained by the static-quenching method. Experimental findings and data are for the intermediate compounds of tephroite and rhodonite with their respective eutectics represented at 25.5 and 37.2 weight-percent silica. Tephroite melts congruently at 1,347° C., and rhodonite melts incongruently at 1,286° 8.. A metastable transformation was determined to exist at the 1,347° C. isotherm, the congruent melting point of tephroite. A composite X-ray-diffraction pattern was formulated for synthetic rhodonite. This investigation contributes fundamental data leading toward a better understanding of the more complex slag systems.

Jan 1, 1962

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

The mineral processing industry is in boom times. The focus on mill availability and therefore profitability has never been greater, as grinding mill maintenance often dictates the entire plant shut down duration. Advances in mill systemsÆ quality and reliability and the faster, safer relining afforded by RMEÆs Mill Relining Systems have significantly enhanced grinding plant availability and utilisation. Yet relining performance is still affected by the design and planning by a team of stakeholders long before the maintenance team set foot in the mill. For a greenfield grinding plant project, these team players include: 1. project owner, 2. project manager, 3. mill supplier, 4. liner supplier, 5. plant operating personnel, 6. plant maintenance personnel, 7. mill relining crew, and&nbsp; 8. mill reline system supplier (RME). The complex and sometimes competing design demands of mill construction and operation together with the pressure of tight timelines can result in even simple maintenance requirements being overlooked let alone optimising plant design and planning for maintenance. This paper identifies all the involved stakeholders in an effective mill relining &apos;team&apos; and gives principles and considerations for each to more effectively achieve the goals within their vital roles. This paper is aimed to be a practical guide for grinding mill designers and planners to more fully exploit the advances in Mill Relining Systems and improve their mill profitability.

Jan 1, 2008

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

By Ilpo O. Auranen

Background: Mines of today are moving ever increasing tonnages of rock. The new ore bodies tend be of lower grade and located deeper in the earth?s crust. The industry?s focus to overcome this ?deeper but poorer? ore problem has traditionally been to lower the costs by increasing the scale of mining. This has resulted in an ever increasing size of mining equipment like drills, loading shovels, dump trucks. The main focus has been in reducing the cost per ton of mining. This cost focus has often resulted in increased waste rock dilution and more ore losses. From costs to value: Waste rock dilution means waste rock in the concentrator feed. It?s value in open pit mining is equal to the value of ore it replaces. In underground mining, waste rock dilution?s value is equal to the value of ore it replaces added to the costs of mining it. It is commonly accepted that waste rock dilution in open pit mining ranges between 5 and 20% and in underground mining between 5 and 40 % . In a typical large open pit mine ore value is from 20 to 60 USD per ton and mining costs are 1 to 3 USD per ton. One percentage point reduction in waste rock dilution represents savings corresponding to about 20% of total mining operation costs. The difficulty of reducing waste rock dilution comes from the complicated nature of the ores. Accurate ore waste-border detection has not been possible due to excessive costs. Core drilling combined with geochemical lab analysis is the most accurate method for locating ore waste borders. However, it is also expensive and time consuming, which is why it is often combined with somewhat lower cost methods like sampling drill cuttings from blasting drill holes or from reverse circulation drills and analyzing them in a laboratory. The main drawback with these methods, in addition high costs, lies in the sampling accuracy and in the quality control of the whole process when a large number of samples have to be handled manually. In every mine it is possible to halve waste rock dilution by using new on-line analysis technology .

Oct 1, 2009

By A. Duerksen

Surface coal mining in West Virginia has supplied energy to the eastern coast of the United States for over a century. The coal mining industry has been forced to adapt as societal demands regarding health, safety, and environmental impacts have changed with time. More recent pressure has called for another iteration of change: long-term post-mining sustainability. The research presented in this paper investigates one potential solution?or component of a solution?to improve mining sustainability in Appalachia: post-mining wind power. This paper intends to demonstrate and explain the feasibility of synergistic mine closure and wind development. Wind conditions at three reclaimed mine sites in West Virginia were monitored in order to develop representative case studies for post-mining wind power. This paper contains a summary of the literature consulted to plan the site assessments, the methodology employed to execute them, the analysis steps undertaken to derive conclusions, and a discussion of all findings. This research has found that significant cost savings can be yielded from synergistic mine closure and wind development, as compared to greenfield wind development. Though wind conditions themselves remain the primary driver for site feasibility, post-mining wind power is a practice with significant promise for improving project economics, contributing to renewable energy development, enhancing company-community relations, providing local employment opportunities, and exemplifying sustainable business practices in Appalachia.

Jan 1, 2012

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By Wang Xuguang, Zhang Xiaozhi, Li Guozhong, Xiong Daiyu

The emulsion explosive is a new kind of water-based industrial explosives that was developed at the end of 1960s. In the 1970s, BGRIMM invented EL-series emulsion explosive that created a new era of water-based industrial explosives technology and products in China. From single type to varieties, the perfect BGRIMM emulsion explosives technology has been formed, which consists of 9 series, over 30 types explosives and related production equipments and processes such as cap-sensitive rock emulsion explosive, opencast emulsion explosive, coal permitted emulsion explosives, low-temperature-resistant emulsion explosive, high-temperature-resistant emulsion explosive, high power emulsion explosive, bulk emulsion explosive for loading truck and powder emulsion explosive. From the early 1990s, BGRIMM successfully developed opencast emulsion explosives and the computer controlled continuous production line of small-diameter cap-sensitive emulsion explosive which raised emulsion explosive production technology of our country to a new lever. With the successful development of powder emulsion explosive and related computer controlled continuous production line, on-site mixed emulsion explosive and loading truck as well, the category of industrial explosives is getting more complete and reasonable. This paper pres ents the history, achievement and development of BGRIMM emulsion explosive technology, also forecasts the future of linked technology.

Jan 1, 2003

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By A. M. Ouchi

Existing empirical design tools have been developed from fair-to-good quality rock masses (RMR76 >50). This paper presents a focus of ground control research presently being conducted by the Rock Mechanics Group in the UBC Mining Department in incorporating weak rock masses (RMR76 <50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented with over 450 weak rock data points from mines such as the Stillwater mine (Montana), the Eskay Creek Mine (BC) and several mines in the Carlin Trend and other parts of Nevada. The original database is comprised of spans supported with ?traditional? mechanical bolting. In weak rock environments however, this type of support has been found for the most part, ineffective. This paper presents the span and weak rock RMR76 relationship for four different support categories. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

Jan 1, 2008