Search Documents

By Irving Wender

The oxo reaction consists of catalytic conversion of olefins by reacting the olefins with CO and H2 (water gas) to aldehydes that contain one more carbon atom than the starting olefin. The aldehydes are then generally reduced with hydrogen to primary alcohols in a second stage. The two-stage process is called the oxo process. The word "oxo" is derived from the German "oxierung" (ketonization); thus the exact English equivalent of "oxo" is "keto". The oxo process may be applied to nearly all olefins. A wide range of pressures and temperatures may be used in both stages. The pressure range usually employed is 150 to 200 atmosheres. The temperature in the first stage is usually about 140° C. and in the second or hydrogenation stage about 180° C. Although a standard Fischer-Tropsch catalyst may be used for both steps, cheaper catalysts have been utilized to effect hydrogenation of the aldehydes. Most of the information for this, report on the oxo process was gathered from Technical Oil Mission microfilms. T.O.M. Reels 14, 55, and 134 were especially valuable. T.O.M. Report 6 by H. M. Weir was very helpful. Information on the oxo process is scattered throughout documents captured in enemy territory, and the present report does not include all the available data. Some of the information was procured by personal interview. Where, in the body of this report, certain investigators are quoted, the source of the statement is either personal interview or the T.O.M. reports.

Jan 1, 1948

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By K. L. Bainbridge

This report describes the results of a study to determine which types of, and to what extent, mining wastes can contaminate groundwater through leaching of acid-forming or potentially toxic constituents. The primary focus of this study was on coal mining wastes, especially overburden spoils and preparation plant refuse. In addition, the potential for contamination by leachates from clean coal stockpiles was also examined. The study approach included investigation of (a) the amounts and geographic locations of mining wastes in the United States; (b) the chemical character of mining wastes, especially with regard to potentially acid-firming or toxic constituents; and (c) the extent to which acid and/or toxic components are leached from mining wastes by rainwater. To evaluate the leachability of coal wastes, a laboratory waste leaching method was developed during this study to specifically simulate the leaching process over a long-term. Waste samples collected during this study were also leached by the EPA extraction procedure and ASTM waste leaching method. Results of the three leach test methods were compared to evaluate their relative capabilities to predict the leachability of mining wastes.

Jan 1, 1980

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By Robert S. Sanford, Harold C. Pierce

"At one time the Alaskan Eskimo lived in many small settlements scattered along the Arctic coast. These settlements extended as far south as Bristol Bay and several miles inland on the large rivers. When the white man established trading posts, schools, hospitals, and missions, these people gradually congregated around them in a few large villages. The natural fuel supply near many of the large villages along the Arctic coast became exhausted as a result of the abnormally large influx of people from small outlying settlements.The population of Barrow, Alaska, according to the 1940 census, is 363 persons, but since that time it has increased considerably, and later estimates place the present population between 400 and 500 persons. With the exception of 25 white persons, the entire population is comprised of Eskimos.The government maintains a school, hospital, radio station, and weather station at Barrow. In addition to the government, installations, there is a church, a privately owned trading post, and cooperative store owned by the Eskimos.For many years the Barrow Eskimos depended on driftwood and petroleum residue from Cape Simpson for their fuel supply. This fuel provided not only warmth for the Eskimo during the long cold winters but also heat for melting ice, the only source of 'water during .the winter. In recent years the sources of petroleum residue and driftwood have not been adequate to meet the demands for fuel During the winter of 1942-43 and again in 1943-44, Barrow experienced an acute shortage of fuel.The fuel problem at Barrow was brought to the attention of Governor Ernest E. Gruening, who was instrumental in getting a Bureau of Mines engineer4/ to investigate reported coal occurrences in the vicinity. Coal deposits along the Meade River and at Peard Bay were examined during the spring and fall of 1943. The Alaska Native Service shipped in mining equipment in September 1943 and commenced stripping an open-pit mine on the Meade River in June 1944. In conjunction with this work, an engineer5/ of the Bureau explored by churn drilling to determine the tonnage of- coal in the vicinity of the mine. In addition to this work, the Bureau of mines examined coal deposits in Peard Bay area and along the Kuk River south of Wainwright."

Nov 1, 1924

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By Guillermo P. Selas

Perhaps this is the first time that an analysis of the industrial minerals panorama has been made in Mexico for that type of commodities. Because the non-metallic minerals lack the glamour of the metallic minerals and are usually of less unit value than metallics, a comparative study of these commodities has seldom been attempted. Sulphur, fluorite, barite and few others are an exception. Consequently, the statistics on the lowest per unit value industrial minerals, such as limestone, dolomite, gravels, sands, etc., are usually scarce and not always accurate. The following, then, will be an attempt to show a general status of the industrial minerals in Mexico with due reservations regarding volumes and values. According to Kruger (1971), this group of minerals surprisingly very little known, and called non-metallics because the lack of metallic luster, is the largest group of the mineral kingdom. It constitutes perhaps 75% of all the mineral varieties. For the most part, these minerals are compounds of common acids, sulphides, hydroxides and two elements carbon and sulphur. The list of non-metallic minerals is therefore very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulphates and less commonly arsenates, chromates, molybdates, sulphides, tungstates and vanadates. The latter group and many of the oxides are sought usually for their metal content.

Jan 1, 1974

By L. Frost

Physical Conditions Great Britain The physical conditions in the mines investigated in Great Britain are similar to those found in the mines of the Dominion Steel and Coal Corporation, with the important difference that many of the coal seams visited were interspersed by a large number of heavy faults, making the development of a continuous face operation difficult, and in many cases the life of a unit development was exceptionally short, adding to unit cost; but in spite of these difficulties, a great deal has been accomplished in the application of mechanical loading units in a number of the mines in the areas visited. The coal-bearing measures, as in Nova Scotia, consist of shales and sandstones, and in some sections mussel bands overlie the coal seams making roof conditions difficult'. In several mines, the main roof consisted of weak shale bind, being held by a coal roof of varying thickness. This shale bind had a tendency to flow when the coal roof was broken. The floor, in some cases where cutter loaders were operated successfully, consisted of weak, flaky shales with very little resistance and a tendency to disintegrate into powder when broken. The depth of cover under which these mines were operating varied from 250 feet to 2,340 feet, with an average of 1,700 feet. The coal seams varied in height from 3 feet to 8 feet 6 inches, and the gradients from level to 33 per cent. The seams vary in hardness, but all-with the exception of one seam, the 'Morrison Busty'- presented a cutting problem similar to that found in Nova Scotia. The structure and cleavage of the coal was well defined and uniform. Some of the seams visited were gassy, ?but the temperature of the workings generally was not in excess of 70°F.

Jan 1, 1948

Reliable and discriminating small, laboratory scale methods of study have been developed and used successfully in the critical evaluation and interpretation of the carbonization characteristics of a wide range of raw and prepared materials, the variable factors in the coking process, and' the mechanical properties of the carbonized products. The simple and highly economic technologies have been successfully and effectively integrated with detailed surface and subsurface geological exploration programmes (particularly in the coalfields of the .Central Bowen Basin of Queensland) as well as with quality and utilization studies of a nUII!ber of representative Australian and Japanese coals. Previously, only the results of comparatively large, laboratory scale studies have provided information reasonably indicative of those to be anticipated hi industrial practice, but these suffer serious disadvantages in terms of economy of material, time and resources; they have been difficult or even impossible to use as an essential part of any normal or comprehensive exploration programme. On the other hand, although previously developed smaller scale laboratory methods derive considerable advantage from their flexibility, amenity to critical control and inherent potential for speed and economy, they have hitherto permitted no effective or direct comparison with the results of industrial practice or full scale assessment. Comprehensive study results achieved through technologies developed recently at the University 'of Sydney demonstrate that carefully controlled small laboratory scale methods of evaluation quite suitable for use in exploration and, other programmes may be used to predict with considerable accuracy and reliability (in some cases exceedingthat of pilot scale study) the principal strength index of one of the established and internationally recognized full sc:ale tests-the Japanese Industrial-Standard Drum Test. It is probable that further study may establish satisfactory correlations with the results of other standard industrial procedures.

Jan 1, 1969

By L. Ou

This paper reports on research on leaching pyrite in a germ-free system. The effects of mineral particle size, pulp potential and various oxidation agents on pyrite leaching were studied. The results indicated that a smaller mineral particle size leads to a higher leaching rate of pyrite. The optimum results were obtained with a mineral particle size of -0.037 mm. The pulp potential reflected the leaching process and an increasing pulp potential improved pyrite leaching. The leaching rate rapidly increased with the addition of oxidation agents such as Fe3+ and H2O2. However, the precipitate generated by ferric ion coated the surface of the pyrite and prevented further leaching.

Jan 1, 2007

By Sidney Katell

This report, covering the period January 1965 through December 1965, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the seventh in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are From the following sources:

Jan 1, 1966

The object of this talk is to bring before members the importance of the prospector and the' State Battery system to the wealth and prosperity of the mining industry in particular and the State of Western Australia in general, and to touch on the more important features.Customs plants of any sort are usually subject to a good deal of critioism, usually on the large profits made at the expense of the customer, etc., and this often clouds the real value of the work being done.Prospectors, on the whole, are a good class of men; they work under conditions and difficulties which would deter those less spirited. Food, water and mining supplies are often difficult to obtain and frequently have to be transported great distances. Their mining tools are usually of the most primitive type, yet during last year over 109,000 tons of prospectors' ore were handled by the State Battery system for 73,250 fine oz. valued in Australian currency at over £587,000, the value being 57/- per long ton at par.This production brings the State Battery system into fourth position amongst the producers of the State, the yield being exceeded by the Lake View and Star, Wiluna and the Great Boulder.In passing I might mention that these notes were written at the end of the year 1940, and the above figures were for the previous period. The figures for last year, 1940, were not quite so good, being 101,000 tons for approximately 60,000 fine oz., valued in Australian currency at £572,000.In spite of this drop the State Battery system maintained its position as fourth in order of gold output for the State.The extractions, as a whole, throughout the system, were 92·54%, made up of 68·86% by amalgamation and 23·68% by cyanidation. These figures, for a group of 20 plants treating widely different classes of ore, must be considered satisfactory. The total production since inception is over £11,000,000 in Australian currency.State Batteries are usually more or less of a standard design. Ore is reduced to about 2i in. maximum size before being sent to the bins. Challenge automatic feeeders control the feed to each mill unit, amalgamated copper plates collect the free gold. Corduroy strakes are used with some ores after amalgamation, but in only a few cases has this been found of any advantage to the customer.The pulp from the battery is sampled, after leaving the tables, with a "Tazewell" sampler and pumped to dams for subsequent cyanide treatment.The "Tazewell" sampler is a machine driven by the moving pulp; and takes about fifteen dips per .minute from such pulp through a slotted...

Jan 1, 1941

The Autogenous Fine Grinding Kelsey Axial Displacement (KAD) Mill The marginal improvements which continue to be made to fine grinding practices have exposed the limits of conventional technologies and highlighted the need for a radically new approach. The patented autogenous Kelsey Axial Displacement (KAD) Mill design consists of a rotating spherical grinding chamber, which shares the same spherical centre as the shaft-mounted counter-rotating disc assembly. The axis of the disc assembly can be inclined to the axis of the spherical grinding chamber by pivoting the disc shaft about the common spherical centre. The inter-particle energy transfer required for breakage results from particle velocity differentials created by the discs intercepting the rotating mass. Particle size reduction is concentrated in high shear zones, which envelop the outer surface and periphery of the discs. This paper traces the development of the KAD Mill from pilot to commercial scale. Pilot work covers a range of minerals including magnetite, calcite, dolomite, barite, limestone and talc. Test results include open and closed circuit operation in wet and dry modes. Conventional milling constraints and energy consumption issues are addressed while new dimensions are added to the feed size range acceptable for wet and dry grinding to fine and ultra-fine sizes.

Sep 13, 2010

By Charles Fried

The Coal Mine Health and Safety Act passed by Congress in 1969, called for research to alleviate the occupational stresses and hazards of coal miners. Spurred by a series of recent mine disasters the Congress directed the Bureau of Mines to increase its attention to the welfare of miners and to develop better working conditions and personal equipment for use in the mines. As one of the early steps in carrying out the provisions of the Act, the Bureau of Mines commissioned the Behavioral Sciences Group at the National Bureau of Standards to conduct a survey of the state of the art in ergonomics (human factors) as it has been applied to mining.

Jan 1, 1972

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

By G. V. R. Landman

In the early days of underground coal mining, the use of explosives to break coal resulted in a large number of disastrous methane and coal dust explosions and consequential loss of life. Research by the British, French, US authorities, amongst others, introduced many practices that significantly reduced the occurrence of such incidences. The use of explosives designed to be safe in a methane atmosphere, plus the creation of a second free face were two such practices which became commonly used in coal mines all over the world including southern Africa. With its associated coal cutting equipment and labour, the cost of creating a second free face is significant and this, together with the constant drive to reduce mining costs in a competitive market, causes mine management to regularly question the need for the second free face. Also, the safety and nature of permitted explosives has changed considerably since the days of black powder and nitroglycerine-based explosives with the introduction of water-based explosives. In southern Africa mining regulations pertaining to the blasting of coal has its origins in British research which was largely done in the first half of the twentieth century. More recent research by the US Bureau of Mine has resulted in a deeper understanding of some of the mechanisms of methane ignition by explosives and suggests that some of the earlier regulations can be relaxed to a certain extent without compromising safety. This paper gives an overview of the original research done in Europe and the more recent work in the USA, to give mine management and regulatory authorities a deeper understanding of the important safety issues when using explosives in a methane atmosphere. It also suggests that blasting off the solid is no less safe than using a second free face providing certain safety procedures are followed.

Jan 1, 2000

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels ? from mining and processing to the manufacturing of Anished products. In 2009, the estimated real GDP of the United States decreased by 2.4 percent compared with, and the estimated nominal GDP was about $14.2 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. In 2009, the continued decline of the housing market was reflected in reductions in the production and consumption of cement, clays, construction sand and gravel, and crushed stone (those mineral commodities that are used almost exclusively in construction). Production of mineral commodities associated with the manufacture of goods for the housing market, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard also decreased. Declines in auto-mobile manufacturing resulted in reduced production

May 1, 2010