Search Documents

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By Joseph M. Kurtak

The U.S Bureau of Mines conducted a five-year mineral resource assessment of the 16.6 million acre Colville Mining District in northern Alaska, which includes part of the National Petroleum Reserve in Alaska. The study was initiated at the request of the Bureau of Land Management, which administers the majority of the region. The study was done in cooperation with the Alaskan Division of Geological and Geophysical Surveys, the U. S. Geological Survey, and the University of Alaska. During fieldwork, 1593 rock, soil, and stream sediment samples were collected and four bulk samples taken for beneficiation studies. A total of 40 mineral occurrences were documented, including 27 which were previously undescribed. No mining has occurred within the district. Mississippian carbonaceous shale and siliceous mudstone contain stratiform exhalative lead-zinc-silver occurrences. Grades average 8.0% combined lead/zinc and 51 gm/mt silver. Upper Devonian to Lower Mississippian sandstones host breccia veins, containing up to 29% combined lead/zinc and 274 gm/mt silver. Mineralized quartzites of similar age have potential for disseminated-type lead-zinc deposits. Samples from Lower Cretaceous mudstone and shale beds up to 6.5 meters thick, contain as much up to 12% manganese. Upper Mississippian carbonaceous shale and limestone beds contain up to 23% phosphate. Stratiform barite deposits hosted by cherts, are up to 27 meters thick with an average specific gravity of 4.16. Vein-type fluorite occurrences are associated with Mississippian limestone. Moderate potential exists for development of zinc -lead-silver, barite, and phosphate deposits.

Jan 1, 2011

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By R. Jolicoeur, J. F. Jackson, M. A. Green

"The design, construction and commissioning of Kiena Gold Mines Limited's new mill was completed in 15 months ending in September 1984. Rated at 1250 tonnes per day the mill incorporates the latest innovative technology such as semi-autogenous grinding, carbon in pulp, pressure stripping and induction furnace refining. The mill is housed in a pre-engineered building with the leach tanks and thickeners located outdoors in spite of the intense winter cold. 1.0 INTRODUCTION AND HISTORYThe operations or Kiena Gold Mines Limited are located in Dubw1sson Township, approximately 10 Km west of Val d'Or, in the Abitibi region northwestern Quebec. Comprised of 59 mining claims covering 1214 hectares, a large portion of the mining property is overlain by the waters of Lac de Montigny. Sometime between 1911 and 1914 Barney Parker discovered gold in a shear zone on an island in Lac de Montigny that now bears his name. The first shaft the Parker Shaft, was sunk in 1936 from the island to a depth of 136 meters but owing to the known veins being of limited extent and the onset of the Second World War operations were terminated in 1940. In the early l960 1 s exploration drilling indicated an orebody of 4,500.000 tonnes at 6.3 grams of gold per tonne. A causeway was built to link the island to the mainland in 1963 and a new 3 compartment shaft was sunk to 403 metres. The orebody was further delineated and the ground conditions within the orebody and surrounds were evaluated.At the end of 1965 the property was placed on a care and maintenance basis as a mining operation would be marginal with gold selling at $35 per ounce."

Jan 1, 1986

By L. C. Graton, Joseph Murdoch

I. Introduction......................... 26 1. The Relations of Scale in Geologic Work........ 26 2. General Characteristics of Copper Sulphide Ores..... 29 3. Scope of Present Study................. 31 11. Description of the Important Minerals............ 36 1. Pyrite....................... 36 2. Pyrrhotite....................... 41 3. Chalcopyrite...................... 41 4. Bornite........................ 40 5. Covellite....................... 50 6. Chalcocite....................... 52 7. Enargite...................... 59 8. Tetrahedrite and Tennantite.............. 61 III. Conclusions.......................... 62 I. Introduction. The Relations of Scale in Geologic Work. Many features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly 011 this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.' Thus, a mural

Jan 1, 1914

By Louis Huntoon

HISTORY of the Porcupine area has been pub-lished in detail by the Ontario Bureau. of Mines in several issues of its annual reports. An. interesting volume could be written on: this topic; especially if personalities were introduced, such as the. transaction whereby the original title to the Hollinger group of claims was settled between Ben Hollinger and Alex Gillies by the toss of a coin. The early history of the McIntyre mine also had its thrilling events, such as its manager, R. J. Ennis, dodging the sheriff and deposit-ing red-hot gold bricks in the bank to meet his pay-roll. The occurrence of quartz veins containing low gold values was reported in 1896 by E. M. Burwash and again in 1899 by W. A. Parks. The first application for a mining claim appears to have been applied for on Dec. 30, 1906, by W. 0. Taylor, of Toronto, one of the old employees of the Hudson Bay Co. On the recom-mendation of Mr. Taylor, early prospecting was done on the shores of Porcupine Lake. It. was not until the spectacular discovery of the surface croppings at the Dome mine, by J. S. Wilson in 1909, that a rush to the district took place. Exploration was carried on during 1910 and 1911. The big boom was on in 1911, when claims sold on the evidence of mere rock croppings, owing to the prevailing heavy overburden. Rock croppings with specks of gold brought big prices. The country was heavily timbered and most difficult to prospect. My first trip was made during the summer of 1911, while the railroad was under construction from Porquis Junction to South Porcupine. I published my observations in the Canadian Mining Journal, Dec. 15, 1911, discussing in particular the character of the ore deposits and the future prospects of the camp. The first mills were erected in 1911, only to be destroyed by the disastrous fire in July of that year. They were rebuilt and the first important shipments are recorded in 1912. The history of the camp from the discovery of the Dome to the present consists of alternate chapters of great optimism and those of a more non-committal nature. For the engineer unfamiliar with the character of the deposits of this area, and the north country in general, it is at times most difficult to draw conclusions and submit definite recommendations. When valuable orebodies apex at depth, with no surface showings other than slightly mineralized veins of quartz or quartz containing a little visible gold; when at depth valuable veins and ore deposits, paralleling the one being explored, are developed by cross-cutting, such as Nos. 85-58 on the Hollinger, which have been its largest producers, the engineer assumes responsibilities rarely called for in other mining districts. This fluctuating aspect is exemplified in the three large producers, and may be duplicated with some of the old producers now being explored.

Jan 8, 1923

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve's Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company's large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve's initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve's operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By Adrian Daniel

"Dating back to 1934, Con Mine is located directly south to the city of Yellowknife in the NWT, Canada. With mill operations ceasing in 2004, a challenging surface remediation situation resulted which required the treatment of close to 40,000 m3 of Arsenic impacted material.Through much of the period of 1941 to 1970, Con Mine treated their refractory arsenopyrite ore through the use of an Edwards Heath roaster. With mounting environmental pressure and through Canadian governmental studies during 1950 to 1970, attention was directed to the Arsenic Trioxide material being collected by two Doyle scrubbers on the Con’s roaster stack. In 1970, the roaster was decommissioned leaving the resulting Arsenic material in two containment areas on surface.As a result of Con Mine entering into remediation in 2004, the Con’s autoclave, commissioned in 1992, was dedicated to the immobilization of high impacted Arsenic material through the combination of excess Iron under high temperature and oxygen overpressure. Examined, herein, is the history and chemistry of the Con Mine autoclave as well as the two stages of chemistry for the Water Treatment Plant used to remove arsenic, heavy metals and WAD cyanide from tailings water. Simplified capping plans of the tailing containment areas and a high arsenic impacted area are also presented.INTRODUCTION TO CON MINECon Mine (Con) is situated just south of the City of Yellowknife in the North West Territories (NWT) Canada and is bounded locally by Yellowknife Bay (North Extension of Great Slave Lake) to the east and Kam Lake to the west (Figure 6). The discovery of gold at Con was made in 1934 and mineral rights were acquired by Consolidated Mining and Smelting Limited (Cominco) and Falconbridge soon thereafter. Nerco Minerals Limited (Nerco) took control in 1986 and in 1993, was subsequently sold to, Miramar Mining Corporation which in turn was purchased by friendly takeover involving Newmont Mining in November 2007 as a result of acquiring the Miramar’s Hope Bay project. Con’s underground operations ceased in September 2003 and have since entered into the remediation of the site. The current surface lease holdings are about 340 Hectares (Table 1) which sits on top of the Archean-aged Yellowknife Greenstone Belt."

Jan 1, 2009

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1990. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1991

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By W. M. Williams

The Canadian steel industry is now in many ways a mature one, having achieved many technical successes during its hundred-year history. It is interesting to look back over this period, to learn something of the histories of the different producers and of the people and forces that shaped their development. The following article provides a thumbnail sketch of the Canadian steel industry as it exists today. It is intended for the general reader, not for the specialist who will want to consult the several books and theses written on the development of the industry during the last hundred years. The famous Les Forges du Saint-Maurice, an important iron producer for a century and a half, provides a natural historical starting point for a look at the four major players - Dosco, Algoma, Stelco and Dofasco - who have provided most of the hundreds of millions of tonnes of steel, in every form from horseshoes to tinplate, needed in the twentieth century. The smaller companies which have sprung up in the last 20 or 30 years are dealt with briefly - but only because their history is so recent. Not so long ago the mini-mill, based on scrap rather than on the blast furnace, was thought to be specially suited to the economies of the smaller developing countries of the Third World. However, recent history has made it evident that the small plant, specializing in a few basic products (e.g. reinforcing bar) or taking advantage of special circumstances, can successfully compete with the large blast furnace/primary steel producers.

Jan 1, 1999

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

By Paul J. Axtell

The results of in-situ geophysical cross-hole tests on improved soil by soil mixing (SM) and jet grouting (JG) are described. This testing was conducted on soil improved by SM and JG columns constructed in the downstream free-field of Tuttle Creek Dam near Manhattan, Kansas as part of the seismic retrofit. Results of similar geophysical testing performed on untreated soil in the vicinity of the Downstream Test Program (DTP) area, as well as beneath the embankment at several locations, are also described and used for comparison purposes. In-situ shear moduli are also compared with those determined in laboratory resonant column tests. The increase in stress wave velocities and associated shear moduli by SM and JG treatment are presented for use in liquefaction potential and seismic deformation analyses of SM or JG treated soil. This data is required to determine the decrease in liquefaction potential and earthquake-induced permanent deformations due to SM or JG with respect to that of untreated soil.

Jan 1, 2008

By J. N. Murphy

The use of the National Science Teachers Association (NSTA) regional meetings as a forum to educate teachers on the role of minerals in our society has been immeasurably successful. Each year, on average about 3,500 to 4,000 teachers participate in each of the three regional NSTA meetings. At each of these meetings, nearly 2,000 teachers visit the “Minerals Coalition Booth” and receive free mineral samples and other educational support materials. Some rules of thumb for a successful booth at the NSTA are provided. Considering the level of effort for such a booth, are there alternatives? The NSTA also organizes a national annual meeting with attendance of about 20,000. All who have participated in a regional NSTA agree that the traditional approach of providing a mineral set and teacher materials for a substantial fraction of the 20,000 attendees is not feasible. Conceptual alternatives for minerals education at the national NSTA meeting are introduced and evaluated.

Jan 1, 2001

Organization Place Date 1917 American Electro-Chemical Society Detroit; Mich. May 2-5 American Waterworks Association Richmond, Va. May 7-11 American Institute of Electrical Engineers New York City May 18 America' Society of, Mechanical Engineers Cincinnati, Ohio May 22-25 American Iron and Steel Institute New York City May 25-26 ' Interstate Oil Mill Superintendents Association. Augusta, Ga. May (last wk.) Electric Power Club Hot Springs, Va. June 11-14 Society for the Promotion of Engineering Education .... Evansville, Ind. June 19-22. American Institute of Electrical Engineers Hot Springs, Va. June 25 American Society for Testing Materials Atlantic City, N. J. June 26-30

Jan 5, 1917

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011