Search Documents

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By Victor M. Mercado, Jay B. Shah

Spalding DeDecker Associates, Inc. (SDA) designed a tunnel project that fulfilled the Sustainability Objectives of Social Equity, Environment, and Economics. The project translated the principles of Sustainable Development into actions that lessened the impacts of construction on environment, lives of residents, businesses, traffic, and other social systems (i.e., shopping, recreational, and educational). The project involved the construction of a 16,108 feet of 84 inch diameter sanitary sewer interceptor by tunneling 40 feet beneath the ground surface through difficult geological and hydrogeological settings. An effective public information and stakeholders relationship program was developed to achieve the stated objectives of sustainability.

Jan 1, 2003

By Peter Zhang, Daniel Su, Bo Hyun Kim

Shale gas wells drilled in longwall chain pillars are influenced by longwall mining. Longwall mining on each side of the chain pillars can create overburden movements and induce deformations in gas well casings. If the deformations result in a casing breach, intrusive shale gas could leak into the longwall mine with serious safety consequences. This study concerns five shale gas wells in the chain pillars between two adjacent longwall panels in the Pittsburgh coal seam under a cover depth of 670 ft and a mining height of 7 ft. The gas wells were constructed with typical casing design, but a casing cementing alternative with uncemented production casings was practiced. Four production casings were uncemented, and one production casing was unintentionally cemented with good quality cement to a 535-ft depth and low-quality cement stringers from a 444- to 535-ft depth. The longwall faces passed by the shale gas wells as each adjacent longwall panel retreated. Production casings were surveyed by a multi-finger caliper after each panel was mined. No deformation was detected in the four uncemented production casings, but small deformations were detected in the partially cemented production casing. The maximum measured deformation in the cemented production casing was 0.05 in. after first panel mining and 0.06 in. after second panel mining. The casing deformations were also predicted by the FLAC3D model set up on site-specific overburden geology. The predicted deformations were in good agreement with the measurements in terms of deformation locations and magnitudes. All five shale gas wells resumed normal production after being temporarily plugged during the period of mine-by. This study provides a successful demonstration of the effectiveness of a casing cementing alternative for decoupling production and intermediate casing, and thus minimizing the influence of longwall mining in the shale gas wells drilled through longwall chain pillars.

Jul 1, 2023

By B. Cavender

Investments in new technology are often intended to improve the production or cost performance of existing operations. The economics used to justify these projects can be flawed, however, if they do not adequately consider the potential benefits of the alternative: the fully optimized use of the facility's present equipment and personnel. While new technology can be effective, dramatic improvements in production performance can also be achieved through the rigorous application of standard industrial engineering and operations management practices. An intermediate approach may also be effective: many basic improvements in the mine or plant necessary to support new technology will be equally effective when implemented for the facility's present operators. Firms that optimize their present operations are able to save the capital and avoid the risk associated with new technology. These firms will also be able to capitalize more quickly on new technology when it is implemented.

Jan 1, 2000

By Eivind B. Jensen

Introduction Though temporarily shutdown due to the depressed economy, the Henderson mine is a large underground molybdenite producer, using a continuous panel-caving mining system. The location of the ore body requires access from the surface through three shafts, the collars of which are located about 3.15 km (10,350 ft) above sea level. At this altitude, normal temperatures are such that heat must be added to intake-ventilation air for about half of each year. This prevents ice from building up in the intake shafts, waterlines from freezing underground, employee discomfort, and equipment-related problems such as pneumatic rock drill icing and cold starting of diesel engines. Because of topographic and environmental constraints, the Henderson mill and concentrator are located 24 km (15 miles) from the mine, on the west side of the Continental Divide. All ore from the mine is transported to the mill by an electrified rail haulage system, with 15.4 km (9.6 miles) of the trip being underground through a double-track tunnel. A shaft at the midpoint of the tunnel exhausts air drawn from the mine and from the portal that is at an elevation of 2.7 km (8,950 ft). Intake air at the portal must be heated for part of the year to prevent ice buildup. Mine Ventilation System The mine ventilation system uses three sources of fresh air and two exhausts. The primary freshair intake is No. 3 shaft. It is concrete lined to a diameter of 7 m (23 ft) for a total depth of 698 m (2,291 ft). An airflow of 755 m3/s (1.6 mil¬lion cfm) is supplied to this shaft by two vane-axial 932-kW (1,250-hp) fans on the surface. The air is distributed within the mine by means of fresh-air distribution levels connected to production and development levels by raises. A secondary source of fresh air to the mine is provided by No. 2 shaft, the primary man and material access. This shaft is concrete lined to a diameter of 8.5 m (28 ft) for a total depth of 946 m (3,105 ft). Downcast airflow is induced by a pressure differential produced by the fans in the system such that net intake and exhaust volumes are equal. The No. 2 shaft flow of 165 m3/s (350,000 cfm) enters the mine network from the production and haulage levels. Exhaust air is moved from the various working levels through connecting raises to exhaust col¬lection levels that return it to No. 1 shaft. No. 1 shaft is the primary mine exhaust. It is concrete lined to a diameter of 7 m (23 ft) for a total depth of 788 m (2,584 ft). Three vane-axial 932-kW (1,250-hp) exhaust fans are located at the collar of No. 1 shaft, producing a flow of 850 m3/s (1.8 million cfm). In addition, an airflow of 71 m3/s (150,000 cfm) from the intake distribution level is exhausted via the haulage tunnel, by means of No. 4 shaft located midway in the tunnel. The main features of the mine ventilation network are summarized in Fig. 1. Ventilation Air-Heat Plants No. 3 Shaft In the early design phase of No. 3 shaft, it was recognized that air heating would be required to maintain underground temperatures above 0°C (32°F) during cold winters in the Colorado mountains. When the air reaches the mining

Jan 1, 1983

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By J. A. Herbst, C Lo. Y, Z. Rogovin

The identification and quantification of incipient overload conditions in mills have recently been found to be very significant in the design of tumbling grinding mills. To investigate these phenomena, a series of experiments was conducted in a Plexiglas mill operated in both dry and wet modes. For on-stream measurement of the mill charge weight, volumetric filling, dynamic angle of repose, and mill power, an electronic system was developed. The mill was filled to various levels with 19.1-mm (3/4-in.) ceramic balls as grinding media. As feed material, grindable limestone or 3.2-mm (1/8-in.) nongrinding ceramic balls were fed at various steady-state rates to determine the incipient overload conditions. The prediction of overload has apparently been reduced to predicting the feed rate that results in 50% mill filling.

Jan 1, 1988

By Mahmut Altiner

In the present study, the use of horse residue as an alternative reducing agent in the roasting of a low-grade goethite ore containing 17.60% Fe was investigated. Additional roasting experiments were carried out with corn starch and without reducing agent for comparison. Each roasted product was characterized using X-ray diffraction (XRD) and magnetic hysteresis (MH) loops analyses. The optimum roasting conditions (roasting temperature [400, 500, and 600 °C], reducing agent/ore ratio [0.04, 0.08, and 0.12], and roasting time [10, 20, and 30 min]) were investigated based on the Taguchi approach. The magnetic susceptibilities of the roasted sample with the addition of reducing agents were higher compared to that of the roasted sample in the absence of reducing agent. Experimental findings indicate that the horse residue can be used as the reducing agent. Finally, an iron ore concentrate assaying a Fe grade of 62.12% with a recovery of 56.93% was prepared using wet magnetic separation at a magnetic intensity of 0.5 T from the ore roasted under the following roasting conditions: roasting temperature of 500 °C, reducing agent/ sample ratio of 0.08, and roasting time of 30 min.

Jun 3, 2020

By J. J. Moore, I. Iwasaki, L. A. Lindeke

Correlation of scale-up from small-scale batch laboratory mills to large-diameter industrial mills was established by performing two series of laboratory and pilot plant grinding tests using a magnetic taconite ore and a siliceous sulfide ore. In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter on grinding power and ball wear are illustrated.

Jan 1, 1988

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10 µm. The test conditions included centrifuge howl and scroll speeds, volumetric feed rate, solids concentration and pond depth. Centrifuge performance was evaluated using size selectivity curves and the corresponding performance parameters, along with product yields and solids concentrations.

Jan 1, 2002

By F. L. Pierson

Since the discovery of 'potash in the Carlsbad area in 1926 and the start of mining operations in 1931, "first mining," operations have been carried on. This is a room and pillar system in which approximately 62% of the total ore is removed. Or the basis of ore reserves and rates of extraction, the life of the mine in the early; days was estimated to be well over 50 years, however, even with an increase by additional ore reserves, it became increasingly apparent that the life of the mine was being shortened considerably by increased production. Further cause for the shortening of mine life was due to the exceptionally weak back over the northeast quadrant of the main orebody which had .caved in on first mining up to a height of 8 feet. Thus, in 1953 the decision was' made to begin pillar pulling, also called, second mining or final mining, and in December of 1953 this program was started after much discussion.

Jan 1, 1965

By Bruce M. Davis

The variogram is the function used to express the intercorrelation of a regionalized variable. It is used to quantify, for example, the natural variability of mineralization and in that sense may be thought of a average disimilarity between metal quantity at two points inside a deposit.2 As David2 explains, appropriate mathematical functions of distance and direction are used to characterize variograms, a process that he says is analogous to selecting a normal or lognormal model for an observed distribution. Methods for choosing a model for the underlying variogram of a random function based on the sample data appear in the literature.3,8 A crossvalidation procedure is available to check the validity of the model.3 However, statistical validation of the choice of the model through the mechanism of hypothesis testing is not presently available. In the section to follow, notation and background material is presented upon which a large sample test procedure will be constructed. The stationarity assumptions presented refer to covariance stationarity. A test procedure is then proposed, and an example is given for the case of the one dimensional random process.

Jan 1, 1979

By L. Bomvisinho

As a result of today?s requirements for larger mills with higher power demand, and in order to cope with maximizing throughput, and optimize grinding efficiency, the minerals industry is increasingly relying on the robust Gearless Mill Drive (GMD) solution. This paper describes the new features introduced with the revolutionary ABB drive controller for Gearless Mills, and explains the benefits this can bring to the operation. Extensive surveys have been performed with GMD users to gather suggestions and understand the market wishes. As a result the new driver controller capabilities and functionalities focus on safety, high availability, operational flexibility and remote diagnostics.

Jan 1, 2010

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By W. J. Karwoski

A ground-support system for grizzly and haulage drifts was tested in Magma Copper Co.'s San Manuel mine. Eight two-piece, wide- flange steel sets were erected in a ventilation drift on the 2315 grizzly level. The sets were lagged with three different materials and back- packed with pea gravel and sand. The pillar on either side of the drift support system was instrumented with stressmeters and rock-bolt load cells, the backfill with pressure cells, and the steel sets with load cells. Results indicate a better survival rate than with typical monolithic concrete.

Jan 1, 1979

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By Richard J. Waxweiler, Frank E. Lundin, Robert J. Roscoe, Victor E. Archer, Michael J. Thun, Joseph K. Wagoner

[Introduction] Since excess lung cancer mortality was first noted in the late 1800's among Joachimsthal-Schneeberg miners, there have been a number of studies of the long term health effects among various types of miners exposed to elevated levels of radon and its radioactive decay daughters. Substantial excesses of lung cancer have been noted among miners in the Joachimsthal mines (Sevc, 1976) , lead-zinc miners in Sweden (Axelson, 1979) , fluorspar miners in Canada (DeVilliers, 1971) , iron miners in Sweden (Renard, 1974) , uranium miners in Canada (Hewitt, 1976), and metal (Wagoner, 1963) and uranium miners in the United States (Lundin, 1971; Archer, 1976). The latter prospective cohort has also been shown to be at an excess risk of death due to tuberculosis, nonmalignant respiratory disease, and accidents when followed through September 30, 1974 (Archer, 1976). This report extends the followup of this cohort of miners through December 31, 1977 and expands the mortality analysis to investigate more cause-specific categories. [Methods] During the decade beginning with July, 1950, medical teams from the United States Public Health Service (USPHS) examined 3362 white and approximately 780 nonwhite males who had worked underground in uranium mines in the Colorado Plateau at least one month by January 1, 1964. Occupational, medical, and smoking histories were obtained during the examinations and often updated/confirmed during subsequent annual censuses of the miners conducted by the USPHS. The white miners now have been followed-up through December 31, 1977 using the Social Security Administration, Internal Revenue Service, direct telephoning and various other sources. Death certificates were obtained for the deceased and coded directly into the Seventh Revision of the International Classification of Diseases, Adapted, using the rules in effect at the time of death. Deceased miners for whom no certificate has yet been located were assumed dead on the date specified by the reporting agency, cause of death unknown. The uranium miners cohort was analyzed using a modified life-table system developed by the National Institute for Occupational Safety and Health (NIOSH). Person-years at risk of dying (PYAR) were calculated for each miner from his first USPHS medical examination date or date upon completion of one month of underground uranium mining if that was later. PYAR were calculated specific for five-year age groups, calendar periods, and periods after first underground uranium mining. The numbers of cause-specific observed deaths among the cohort occurring by December 31, 1977 were compared to the numbers of expected deaths. The expected deaths were calculated by multiplying the appropriate PYAR by the United States death rates for white males specific for five-year age groups, five-year calendar periods, and cause. The results were summed over the age and calendar period specific categories to obtain the total expected deaths for each cause. Standardized Mortality Ratios (SMR's) were calculated for each cause by dividing the observed number of deaths by the expected number of deaths and multiplying by 100. In some tables, two-sided 95% confidence intervals for the SMR's were computed using either Fisher exact confidence limits, if the observed frequency was less than eight, or approximate confidence limits, if the observed frequency was eight or greater, to indicate statistical significance. Because a priori hypotheses had been well established, one-sided lower confidence limits were used for tuberculosis, lung cancer, other nonmalignant respiratory disease (ONMRD), accidents, and total mortality. [Results] The cohort included 589 miners first examined in either 1950, 1951 or 1953; 753 first examined in 1954; 1235 first examined in 1957; 5 first examined in 1958; and 782 first examined in 1960. In Figure 1 the distribution of the cohort by first year of underground uranium mining indicates that 13.7% started before 1947 and would have thus had an opportunity to be followed beyond 30 years

Jan 1, 1981

By J. W. Stevenson

At this 5th U.S. Mine Ventilation Symposium I would like to focus your attention on safety and the contribution of the ventilation engineer over the past 50 years. This conference affords us the opportunity to express, to listen, and to learn. As ventilation engineers it is indeed an exciting time--a time that not only stimulates our imagination but also pin points our aims in our quest to obtain zero fatalities by the year 2000, the goal expressed by William J. Tattersall, Assistant Secretary of Labor, Mine Safety and Health Administration. In the past, coal mine ventilation has often been unfortunately synonymous with explosions and resulting fires. Those not familiar with us do not recognize the painful evolution of the coal mining industry and particularly the evolution of mine ventilation. To put my presentation into perspective, I recently reviewed a U.S. Bureau of Mines Bulletin No. 586 - "Historical Summary of Coal-Mine Explosions in the United States 1810 - 1958 prepared by H. B. Humphrey Mining Health and Safety Engineer. This bulletin was published in 1960. Mr. Humphrey stated "In 1946, factors contributing to the explosions occurring from 1941 to 1945 were: (1) The rapid increase in the use of electrical equipment at face regions where gas and dust are most likely to be found; (2) the increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost, which in many mines has resulted in neglect of even rudimentary precautionary measures; (3) multiple-shift operation without provision of time for adequate maintenance of equipment, effective rock dusting, and testing for gas; (4) decrease in supervision owing to demands on supervisors for maximum tonnage and loss of competent supervisors to other employment; (5) lack of effective supervision, owing to numerous new conditions, some of them war-connected; (6) inability to obtain adequate equipment repair and replacement parts; (7) shortage of labor and inadequate training of coal-mine workers; and (8) failure of both miners and mining officials to show regard for safety in changing from hand-loading to mechanized methods". Most of the eight factors listed by Mr. Humphrey continue to affect our work lives as mining engineers. The increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost has never changed. The local and regionalized coal industry of the 40's is today competing against the world coal market. Our mines work or shut down based on cost. This has always been the case. During the five year time-frame Mr. Humphrey was documenting, 345 miners were killed in major explosions. A major explosion was one in which five or more miners were killed in a single accident. In addition, 105 more miners were killed in minor explosions for a total of 450. What a wanton waste of life. What fears, anxieties, miseries, and sufferings were created by these accidents. However, we must remember and keep in mind that the coal mining company officials, engineers, and foremen, the governmental agencies- federal, state, and local - were using the technical tools and knowledge available to operate the mines as safely as they could. Obviously mine ventilation engineering technology was woefully inadequate.

Jan 1, 1991

By J. S. Hastings

Tertiary calc-alkalic to alkalic rocks of the Little Rocky Mountains in north-central Montana host low-grade heap-leachable gold-silver deposits being mined by Pegasus Gold Corporation. Total production from 1884 through 1985 is estimated at 22,625 kilograms (727,414 ounces) of gold. This includes 10,774 kilograms (346,400 ounces) recovered by Pegasus between 1980 to 1986 from 20,318,000 tonnes (22,396,000 tons) of ore grading 0.960 grams of gold per tonne (0.028 ounces per ton). Silver production during this latter period was 24,556 kilograms (789,500 ounces), but reliable silver statistics prior to 1980 are not available. Ore reserves as of January 1, 1986, were estimated to be 35,380,800 tonnes (39,000,000 tons) grading 0.720 grams per tonne (0.021 ounces per ton). Present ore production is 5,533,920 tonnes (6,100,000 tons) per year at a 0.45 to 1 waste to ore strip ratio. Current annual metal production is about 2,644 and 5,288 kilograms of gold and silver respectively (85,000 and 170,000 ounces of gold and silver respectively). The Little Rockies were formed by a calc-alkalic to alkalic magma penetrating through the Precambrian basement into the overlying Paleozoic and Mesozoic sedimentary rocks. This intrusive center is Dart of the Central Montana Alkalic Province, a region comprised of twelve separate intrusive centers aligned in a northeast trending belt measuring 200 by 400 kilometers (124 x 248 miles). The ore deposits are structurally controlled epithermal systems which vary from deeper narrow veins to shallow, wide, low-grade stockworks, breccias and intensely fractured "sheeted" zones. The shallow types are now being exploited. Primary mineralization consists principally of gold and silver associated with pyrite, native gold and silver, sylvanite, calaverite, and hessite. Alteration is broadly classified as weak argillic. Pyritization, kaolinization, silicification and feldspathization are the dominant forms of alteration. Fluorite is a common hydrothermal gangue mineral.

Jan 1, 1987

By D. P. Patil, T. C. Rao, J. P. Barnwal

Factorial design of column flotation experiments was used to understand the main and interactional effects of the column parameters. In the experiments, the air flog rate, the wash-water, flow rate and the froth depth were varied at two levels. Analysis of the results showed that an increase in airflow rate had a deleterious effect on the grade of the concentrate, whereas, an increase in froth height increased the grade. The interactions between airflow and wash water and between airflow and froth height were significant with respect to grade of the concentrate. These results demonstrated that, from an ore containing 12.76% P2O5, it is possible in a single-stage flotation column to obtain a concentrate containing 31 % P2O5 (10.6% Si02) with a recovery of 94%, thus reducing the number of cleaning stages that would be required if conventional flotation cells were used.

Jan 1, 1997