Search Documents

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By S. Kawatra, K. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from fines migration. Agglomeration of the ore can immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it “feels right”. We have developed procedures to quantitatively determine whether a binder gives good performance in an acidic solution, and have identified several binders that will be suitable for copper heap leaching.

Jan 1, 2007

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By A. A. El-Midany

Traditionally, the choice amongst different upgrading techniques or in finding the optimum operating conditions for a given upgrading technology depends on whether one is looking at the grade or the recovery of the valuable mineral in the concentrate. In fact, the conclusions are not usually the same. This is because the best technique or optimum operating conditions for the highest grade are not the same as the conditions to achieve the maxi-mum recovery. Therefore, a unique measure that takes into consideration both grade and recovery is urgently needed. Finding such a measure is the objective of this paper. A proposed measure provides a selectivity index in the range of 0 to 1, where 0 is no selectivity and 1 is ideal selectivity. The index can be obtained by plotting the so-called Fuerstenau upgrading curve, which relates the recoveries of the components in products of separation and a running regression applying a one-parameter equation. The measure was applied to assess the selectivity of selective flocculation under different operating conditions when used as a sensitive upgrading technique for ultrafine ground ores. After applying the proposed selectivity measure in the case of the selective flocculation of ultrafine Egyptian iron ore without the addition of cations, it was found that the optimum conditions are pH 11, 1 kg/t sodium silicate and 0.4 kg/t potato starch with a selectivity index of 0.55. With the addition of cations, the optimum conditions were found to be pH 11, 1 kg/t sodium silicate and 2 kg/t potato starch with a selectivity index of 0.65. It should be noted that determining these optimum conditions using the traditional grade or recovery measures was highly ambiguous.

Jan 1, 2008

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By S. Chander, S. W. Musselman

The molecular structure of hydrophobic and hydrophilic groups in nonionic surfactants has been related to the wetting and dispersion of selected pigments. The nonionic surfactants included in this study are acetylenic diol based surfactants and ethoxylated alkyl phenols. The Langmuir model could be used to fit adsorption data. Further analysis of the data showed that the free energy of adsorption was a function of adsorption density of the surfactants at the interface. The change in free energy with adsorption density could be interpreted by considering a change in the orientation of the adsorbed molecules. Acetylenic diol based surfatants were found to have an area per molecule of 2-3 times that of similarly ethoxylated alkyl phenols. The wetting and dispersion properties of lamp black, a model hydrophobic surface, by these surfactants were investigated by contact angle measurements and particle size analysis. Acetylenic diol based surfactants with ethylene oxide contents between3.5 and 10 moles per molecule and alkyl phenol based surfactants with approximately 9 moles of ethylene oxide per molecule were found to provide superior wetting abilities. Longer ethylene oxide chains were required for superior dispersion capabilities within each family of surfactants. Complete wetting and dispersion was found to occur above the critical micelle concentration of the surfactants.

Jan 1, 2000

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By Rudolf E. Greuer

It is undisputed that an interaction between mine fires and mine ventilation systems exists. The ventilation carries the poisonous and sometimes explosive combustion products, which constitute the greatest danger of mine fires, through the mine and it provides the oxygen on which the intensity of the fire depends. The fire, on the other hand, can produce considerable ventilation disturbances which make it difficult to predict the path along which the combustion products travel. The opinions, how serious a threat such fire generated ventilation disturbances are, vary. Where shallow deposits are mined and brisk ventilation currents are used, it is frequently felt that these disturbances are of no serious concern. Where mine workings extend over larger elevation differences and where such disturbances have been encountered and been the cause of some larger disasters, their assessment is an integral part of all fire emergency plans. The author felt that the potential of digital computers for the design of ventilation emergency plans, contrary to their acceptance for conventional ventilation planning for more than two decades, is not yet fully utilized. He designed a program for the simulation of ventilation systems under emergency conditions in particular fires. This was part of work completed for a contract with the U.S. Bureau of Mines ( Open File Report OFR 115(1)-78)

Jan 1, 1980

By Akihiro Higashide, Roy H. Patten

The DOT Tunneling method combines two conventional earth pressure balance shield machines in an overlapping cylindrical arrangement. The method allows two tunnels to be driven simultaneously with mini¬mum cross sectional area. Two full size trials, one configured horizontally and one vertically stacked, were successfully completed employing the DOT method. The method was then utilized for the new transportation system. The goggle-shaped DOT machine, 9.36 m high by 15.86 m wide, is the largest earth pressure balance shield machine in the world. This paper includes a general description of the DOT tunneling method as well as a history of its development.

Jan 1, 1995

By I. A. Costa, Y. Fouquet, F. Barriga

"Lucky Strike and Menez Gwen are two hydrothermally active sites located along the border of the Azorean plateau, southwest of the Azores islands where the alteration processes affecting basaltic rocks are prominent (Costa et al., 2003). Here we report on a slabby brecciated rock, abundant at both Lucky Strike and Menez Gwen, composed mainly of basaltic fragments cemented by hydrothermal precipitates from warm fluid circulation system. Research reveals that hydrothermal alteration takes place mainly by replacement processes, in which silicification is dominant (Costa et al., 1997 and Costa, 2014).Petrographic observations, including scanning electron microscopy (SEM), microprobe analysis, and mass balance studies made on basaltic fragments within the breccia show that silicification is one of the main processes resulting from hydrothermal fluid circulation. This alteration process leads to complete replacement by silica, in extreme cases, forming an impermeable cap that may contribute to the formation of sub-seafloor sulphide deposits, including examples in the geological past."

Sep 1, 2014

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By Peter J. Tarkoy

A great deal of attention has been directed toward the complexities and inadequacies of exploration and pre-bid geotechnical information for heavy construction projects, differing site conditions, and the adversary relationships which generally develop as a result. The adversary position has been maintained at all cost. The solution is simple, if not easy. The solution requires strict and equal adherence to given principles by all parties involved, throughout the life of the project, from conception to completion. It is necessary to review and redefine some basic concepts, without value judgements, from a context of getting the job done. In a recreated context, the role of truth, judgement, responsibility, and integrity, in exploration, engineering design, construction estimating, and project construction, will be examined. It is suggested that anticipated geotechnical conditions be defined unconditionally. The alternative choice is to give the bidder the opportunity of making the interpretive judgements based on geotechnical data. Similarly, a unilateral method of establishing encountered conditions that are agreeable to both owner and contractor, must be outlined prior to contracting. As anticipated and encountered conditions are firmly and accurately established, significant differences can evaluated based upon limitations specified in the contract documents. Impact of differences on project costs can be fixed by pre-defined methods.

Jan 1, 1983

By Robert S. Shank

Introduction The Pinto Valley open-pit copper mine is located in southern Arizona, 11 km (7 miles) west of Miami. Production at Pinto Valley began in 1974. About 350 Mt (386 million st) of ore and waste was removed by the end of June 1982. At that time, the mine was using more than 90 major equipment items with a total mobile fleet numbering 320. Some of the major equipment consisted of four Marion M4 rotary drills; six P&H 15, 11.5- and 19.1-m3 (15- and 25-cu yd) shovels; and 24,136- and 154-t (150¬and 170-st) Wabco haulage trucks. This equipment was used to move more than 139 kt/d (154,000 stpd) of ore and waste. The mill was processing more than 50 kt/d (55,000 stpd) of mine ore. Shutdown A two-week vacation shutdown began in July 1982. Maintenance jobs were scheduled, and most employees left for the vacation. During the vacation period, copper prices fell below $1.32/kg ($0.60 per lb). Inventories remained at alarmingly high levels. At this point the mine was losing more money operating than it would by being shut down. The vacation shutdown was first extended to five weeks. But, after further evaluation, the mine was shut down indefinitely. In Dec. 1982, Cities Services Co., owner of Miami Operations (which included the Pinto Valley mine and mill), was acquired by the Occidental Petroleum Corp. On March 1, 1983, Occidental sold the operations to Newmont Mining Corp., and Newmont created Pinto Valley Copper Corp., as a wholly owned subsidiary. Copper continued to be produced by the Pinto Valley solvent extraction-electrowinning (SX- EW) plant because of its low cost per pound of production. To ensure proper equipment care during the shutdown, maintenance management was given three goals; • maintain the SX-EW plant; • maintain the environmental and pollution control systems such as domestic water pumps and mine dewatering; and

Jan 4, 1985

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By Richard Hanke

Tunnel construction on the Brightwater Conveyance System?s East and Central contracts required ground modifications of the existing site soils, comprised of sandy alluvium to very dense glacial till, to assist with both hand-mined and TBM tunneling operations at vertical access shafts. The ground modification program was completed with a modified double fluid jet grouting system to construct continuous overlapping soilcrete columns to depths up to 94-ft below existing grade. This paper presents the sequence and methodology for the ground modification work and capabilities of jet grouting for structural support and groundwater control in the challenging soil profile present at the Brightwater Conveyance System Project.

Jan 1, 2008

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987