Search Documents

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By Eric Sitorus, Septian Prahastudhi, Roy William, Wieda Azani

In July 2020, massive slope failure occurred in the southeast corner Grasberg open pit. This was the final episode in the breakthrough of Production Block 2 South (PB2S) of the Grasberg Block Cave to connect to the surface. This breakthrough had been rapidly evolving during the first half of 2020 and occurred as expected with no adverse impacts to safety or operations. To manage and safeguard the exposure to the workforce and operations, numerous hazards were identified and anticipated. The failure of the sill pillar between the open pit and PB2S cave was identified as the main area of interest and was closely watched during the failure process. This paper reviews the systematic approach developed to convert monitoring data into information around the collapse of the GBC PB2S cave sill pillar. The data that was interpreted consisted of micro-seismic, piezometric, ground-based radar and observational inspections. Geological structures on the boundary of the PB2S cave were clearly involved in the breakthrough process. As the cave propagation reached these structures and triggered instability, the resulting acceleration and breakdown were clearly shown by IBIS radar units associated with high movement in the slope. The focus of this paper is on the evolution of changes seen in the micro-seismic data and how it was used to understand the rapidly changing conditions of the sill pillar. The seismic parameters evaluated were event distribution, Es/Ep value, and the seismic moment tensor inversion. The changes of breakthrough indication seen in these parameters were substantiated by Shear Wave Splitting (SWS) analysis that showed a close correlation with the fractured zone above the PB2S cave as indicated by the increasing anisotropy.

Jan 1, 2022

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By Ali Keneti, Xavier Ryan, Gerardo Sanchez, Shannon Goff

In this study, FLAC3D modeling was conducted for ground-structure stability assessment for a pilot tunnel passing under a large shaft excavated in the vicinity of existing structures at Karangahape Station for the City Rail Link Project in Auckland, New Zealand. The analysis involved generation of the geometries and construction sequences in Rhinoceros®, modeling the existing ground condition, calibration of the simulated in situ conditions with the observed behavior of the ground, and excavation of the shaft and the pilot tunnel. A comprehensive interpretation of the results was then performed accompanied by comparison of the predicted behavior with the observed response of the ground during construction.

Dec 1, 2022

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By G. Bonifazi

Certain deposits of incoherent materials which are near the surface and exploitable by open-pit mining may be characterized in real time before they are mined through an analysis of ground-surface imagery. If the slice to be stripped is not overly thick, in fact, surface texture and color properties may be extrapolated to its entire thickness. Image analysis techniques to process ground surface images acquired in situ (or in the laboratory shortly after their acquisition) which yield pattern vectors representative of RGB color component distributions and HSB texture parameters have been developed. The techniques were applied to a mineral sandy ore deposit containing three different lithotypes. Geostatistical analyses showed that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multi-barycenter classification algorithm. Such in situ image-analysis procedures open the way to the proper selection of the ore to be mined, or the proper way for run of mine (r.o.m). processing, or the appropriate blend to be processed before or at the same time as the mining process itself is enacted.

Jan 1, 1999

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By M. S. Celik

Beneficiation of boron minerals by flotation with well defined systems has been very little investigated in the literature. The difficulty arises from the fact that boron minerals cover a spectrum of solubilities. Colemanite, a calcium containing relatively insoluble boron mineral, and borax, a highly soluble boron mineral have been used to exemplify the flotation of boron minerals. The floatability of both minerals using sodium dodecylsulfonate and dodecylamine hydrochloride exhibits considerable differences in their response to flotation. This has been ascribed to variations in the solubilities 0f boron minerals and the presence of the cations in the lattice structure. Flotation tests along with zeta potential measurements are used to elucidate the mechanisms involved in the flotation of boron minerals.

Jan 1, 1992

By Lynne Chastain

The Eastern Shoshone and Northern Arapaho tribes of the Wind River Indian Reservation, Wyoming are interested in developing their industrial mineral resources. The U.S. Bureau of Indian Affairs (BIA), Division of Energy and Mineral Resources (DEMR) is assisting the tribes in evaluating the potential of their industrial mineral prospects for development. Gypsum occurs on both sides of the Owl Creek Mountains in the basal portion of the Jurassic Gypsum Springs Formation. The gypsum resources that are being evaluated crop out along the northern flank of the Owl Creek Mountains in the Sweetwater basin, a small topographic sub-basin of the Big Horn Basin. From October 1998, to April 1999, DEMR personnel mapped, sampled, and drilled the southcentral butte within the Sweetwater basin. Samples were analyzed for free and combined water, and major mineral oxides to determine gypsum purity. Gypsum purity averaged 93.6 percent for surface samples and 95.1 percent for drill core samples. The basal portion of the Gypsum Springs Formation is comprised of several beds of gypsum up to 9 feet (2.7 m) thick separated by 0.5 to 2.0 foot (0.15 to 0.61 m) thick lenses of siltstone and limestone. Overall gypsum in the formation ranges from 35 to 90 feet (11 to 27 m) in thickness. A resource of approximately 7 million short tons (st) (6.4 million metric tons [mt]) has been identified.

Jan 1, 2001

By Ditend Tesh, Godfrey Dzinomwa, Harmony K. Musiyarira

Namibia is known as water stressed country with a limited amount of fresh water. Therefore, the use of water is an important topic in the country’s development agenda. Water is a shared and finite resource, with high social, cultural, environmental and economic value. However, freshwater resources are under pressure from ore processing, industrialization, urbanization and the demands of a growing population. In Namibia, ore processing, coupled with the anticipated increase in water demand for human consumption and other uses, has created significant stress on the limited water resources of the country. This is critical in the mining industry as water remains typically the prime environmental medium (besides air) that is affected by mining activities. This study sought to investigate the strides made in water management in mining, especially in environmentally sensitive areas of Namibia. Most mining companies operate next or alongside farms, national parks and fishing areas. The overall objective of this research was to highlight the current practices in Namibia’s mineral industry operating in environmentally sensitive areas especially in areas where uranium is being mined and processed. The methodology consisted of comprehensive literature review, field visits to the case study areas, and comparative studies with best practices. This study shows that over a ten-year period, freshwater consumption was reduced by over 55% per tonne of milled ore in uranium mines, resulting in substantive financial savings as well as the delay in water augmentation through desalination. The strategies employed by the Namibian companies involve inclusive stakeholders’ engagement, recycling and reuse, and the minimization of water losses. The realization that the water challenge cannot be solved by any one party acting alone has been fundamental in ensuring environmental compliance within the mining industry in Namibia. Namibia’s industrial leaders have increasingly recognized that reducing the water footprint of mining activities must be one of the key performance indicators for management. The major finding of this study was that Namibia with its unique ecosystems, mineral reserves, and emerging industries can harness a wide range of resources both to improve the welfare of its citizens and to protect the integrity of its environment.

Jan 1, 2017

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

By Y. Guo, C. Cao

"China is rich in tungsten resource, but they are mainly associated minerals. The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work summarized the current situation and the development of flotation reagents, technological process, and mineral processing equipments in China. Fatty acid served as the collector and water glass was the depressant to expand the flotability differences in traditional flotation technology. However the water glass inevitably influenced the flotation of tungsten minerals to a large extend, and the suppressed fluorite was difficult to recover by flotation. Abundant water glass lead to the bad settleability of the tailings and the tail water was difficult to circulate, resulted in serious environmental problems. Recent study proved that the selectivity of benzene armour hydroxyl oxime acid (BAHA) salts was adequate for the separation of tungsten minerals from fluorite, calcite and most silicate minerals without any depressant. By this way, sodium silicate was canceled completely in tungsten flotation, greatly improving the recovery of tungsten and the environmental problems caused by tail water treatment would be solved fundamentally. TUNGSTEN RESOURCES AND DISTRIBUTION IN CHINA China is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves [1]. However the wolframite has been dried up and the scheelite resources had become the main resource of the tungsten metal. Table 1 showed the most large and superlarge scheelite deposits in China. China has more than 40 large and superlarge scheelite deposits and the total metallic deserves is more than 3 million ton [2]. But most of the deposits were low-grade and the associated relationship was complicated. For example, scheelite was usually associated with wolframite, molybonite, bismuthinite, pyrite, fluorite, and calcite in Shizhuyuan and Yaogangxian mine."

Jan 1, 2016

By Michael Murphy, Mark Van Dyke, VASU GANGRADE, Brent Slaker

Room-and-pillar mining in multi-level underground stone mines come with unique pillar stability issues. The pillar stability in these mines primarily depends on the thickness of interburden between mining levels and the staggering of pillars. NIOSH has previously established pillar design guidelines for shallow, flat-lying mines and single-level operations, but there is little guidance for ground control design in multiple-level stone mines. Therefore, to improve the overall understanding of ground control in these mines, a microseismic monitoring system has been installed at a multi-level underground stone mine in Tennessee with up to a 243-m overburden and a 7-m interburden thickness between levels. The microseismic system is comprised of nine uniaxial accelerometers and one triaxial accelerometer installed in the interburden. The seismic array is locally focused with all sensors installed within a 625 m2 area and is setup to monitor the seismicity around the formation of the pillar in the lower mining level. Data is collected over 11 months and comprises of over 1,000 high-confidence events that have been located in the study area comprised of post-blast activity. The event locations were identified using a 3D-velocity model, with an average 4-m location accuracy for this array calculated using the system data. Most observed seismicity was on the excavation boundary, both in the interburden and in the roof of the top level. At this stage of analysis, there are no significant rock failures with which to correlate seismicity, but event locations correlate well with presumed damage in the vicinity of blasts.

Apr 26, 2022

By Guy T. McBride

Mr. Chairman, Fellow Keynoters, Ladies, and Gentlemen: It is purposed to consider the theme of this meeting, "The 1970's - Pivotal Decade for the Mineral Industries," from the particular -- some would say peculiar -- point of view of one engaged in mineral engineering education, and this coign of vantage prompts the textbookish subtitle, "Problems and Solutions (?) in Undergraduate Mineral Engineering Education." Three interrelated problems, or problem areas, will be presented and discussed, and where solutions seem to be emerging or seem worthy to be suggested, they will be identified. The three problems are: 1. The goals, and therefore the course requirements, of the undergraduate curricula are in question, 2. The unit costs of undergraduate education appear excessive to those who bear the charges, and 3. The social ambience of the day affects for the worse the work attitudes and the career motivation of both prospective and in-course students. The Need. - Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development, and production levels, Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of our society and profession. The latter reference is, of course, to the current work of the National Commission on Materials Policy (U.S.A.) under the executive directorship of Dr. James Boyd. Predating this, and perhaps to some extent

Jan 1, 1972

By Kumara S. Rachamalla

Long-term stability, appropriate taxation and incentive policies are essential to attract and stimulate investment in the mineral sector. An outline of Ontario's $4.6 billion industry and associated tax incentives is presented. Producers are offered incentives under The Mining Tax Act, federal and provincial income tax acts for exploration and development by reducing Me after tax cost to 13-25¢ for each dollar spent. The Mining Tax Act provides generous processing incentives which have positive effects in enhancing investment and economic advantages of building processing facilities. Non-mining companies and entrepreneurial individuals can receive 25% of eligible exploration expenditures in grants/tax credits under the Ontario Mineral Exploration Program.

Jan 1, 1982

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By William J. Shampine

The Floridan aquifer, which underlies all of Florida, yields water with a sulfate content of less than 50 parts per million in the north-western part and throughout most of the center of the State. In the southern part of Florida and along the most of the east coast, the sulfate concentration generally exceeds 100 parts per million and is as much as 1,700 parts per million. The sulfate concentration tends to be higher in the deeper zones of the aquifer. This map shows the sulfate concentration in the upper part of the aquifer. Sulfate is found in almost all natural water. Sulfate in rainwater is dissolved from impurities and gases in the atmosphere. Rankama and Sahama (1955, p. 314) report that the average sulfate content of rainwater is two parts per million; however, concentrations have been as high as 283 parts per million. Much of the sulfate in rainwater comes from hydrogen sulfide gas which is generated in shallow water on the continental shelves. The combustion of bituminous coal used for heating and industrial purposes seems to be an important local source of sulfate.

Jan 1, 1966

By L. G. Austin

Introduction My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rap- idly developing knowledge of how stressed, brittle solids fractured, based on the Griffith crack theory. On the other hand, reading in the grinding literature gave me: • Kick's Law, which was clearly not correct in the light of modern fracture theory; • Rittinger's Law, which was also clearly not correct; • Bond's Third Law of Comminution, which was claimed to have something to do with the Griffith crack theory, but where the connection between the two was made by intuitive pseudo- scientific reasoning I could not accept; • the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. incorrect statements abound in the literature, such as “the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1 948) and Broadbent and Callcott (1 956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1 953) in Germany. We confirmed experimentally the validity of the equations for describing batch grinding (1 962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, (Fig. 1) (Berenbaum and Brodie, 1959). Irwin (1949) showed from solution of the stress-strain solutions that a small hole in a region of tensile stress reduces stress concentration at the hole, that is, the tensile stress at the tip of a crack or flaw in a solid is much higher than the general tensile stress in the region. The longer the crack, the higher the stress concentration. Griffith (1920) hypothesized that when the regional tensile stress is large enough, then the chemical bonds at a preexisting crack tip are stretched to breaking point, as illustrated in Fig. 2. When the bonds break, the crack becomes longer, the tensile stress concentration increases, the situation is unstable and a crack opens up (propagates) a surface of tensile stress, creating its own tensile stress at the leading edge. Stored strain energy is converted to the kinetic energy of the moving stress field, which is analogous to sound propagation through the solid, so the crack tip accelerates to velocities approaching those of sound. The moving crack will pass through regions that were previously under regional compressive stress. The equations for "ideal" and "Griffith" strengths are where a is the intermolecular distance, y is Young's modulus, g is the energy

Jan 1, 1998

By Irwan Halim, Seung Han Kim

This paper will describe design of precast segmental tunnel lining for the Pawtucket CSO Tunnel Project in Providence, Rhode Island. The tunnel is 11,700 LF long with 30-foot finished diameter to be constructed in complex sedimentary rocks. Special features of the segments include a large keystone and no connector used on radial joints. The typical segments will be steel fiber reinforced, and hybrid segments with additional steel rebars and shear bicones will be used around the adit openings without use of any structural framing. The important design considerations will be discussed, including special 3D segment to adit connection analyses performed.

Dec 1, 2022