Search Documents

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By B. Petri, N. Rouse

"Air overpressure monitoring procedures and instrumentation guidelines which apply to production blasting in underground limestone mining are not readily available. The industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground limestone mines. As such, there was no available background data from which the expected overpressure levels from production blasting in a new underground limestone mine could be predicted. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting in nearby production headings. To ensure the structures could withstand the blast-induced overpressure, a study was conducted to record empirical overpressure data and develop a model which could be used to control air overpressure levels by the production crews. This document describes the procedures used to develop the model, the development of the model, and the applicability of the model for predicting underground blast overpressures. INTRODUCTION A developing underground limestone mining operation required that a ventilation wall be built to house the permanent mine fans. At the time of the study, the mine was a single-level room and pillar operation with a 7.9 meter (26 ft) high roof, 13.7 meter (45 ft) wide entries, and 13.7 meter by 13.7 meter (45 ft by 45 ft) pillar dimensions. The mine is accessed via a 396 meter (1300 ft) long decline and 100 meter (330 ft) deep ventilation shaft. The ventilation wall was to be partially constructed of autoclaved aerated concrete blocks, for which dynamic strength data from explosives loading were unavailable. The company ownership feared that airblast may affect the wall due to the close proximity of the working faces. Therefore, the company management asked that the overpressure levels be estimated and compared with the designed wall strength. Few studies that apply to explosively-driven air overpressure levels in underground production blasting were found through a literature review. Therefore, the logical approach to assess the overpressure levels was to monitor the blast pressures at the site and conduct a thorough evaluation of the data. As a result of this study, the equipment setup and monitoring procedure used to record the airblast data is described. Finally, the experimental data gathered during the monitoring program is presented, trends and findings from the data are discussed, and recommendations for further study are presented."

Jan 1, 2015

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By B. Boutilier, R. Mendoza

"First Majestic Silver Corp. (FMS) is a silver mining company founded in 2002 that operates exclusively in Mexico. It has six producing silver mines, one of which is the La Encantada silver mine (La Encantada) located in the state Coahuila. La Encantada is located near the southern United States border and 708 km (440 miles) north of the city Torreon.La Encantada is located in the Sierra Madre Oriental and is a high-temperature carbonate replacement deposit. Mineralization in La Encantada occurs in many different forms such as veins, chimneys, breccia pipes and reefs (mantos). Mineralization is mainly oxides of iron, zinc, lead and manganese, with high concentrations of sulfides at depth relating to two main intrusive events: the Milagros Intrusive and the La Prieta Skarn.Mining began in La Encantada during the 1950s with small vertical shafts, drifts and raises. It focuses on the high-grade silver zones using traditional hoists and extraction methods, before branching into two main separate mining camps: El Plomo and Penoles camp. Penoles, the previous owner, focused mainly on large ore bodies using post pillar cut-and-fill mining method to extract the higher-grade material. Due to the type of ground, irregularity of pillars, and rock conditions, large amounts of high-grade pillars had to be left in situ to ensure the stability of the excavations. The mined-out areas would then be filled with lower-grade material to assist in the stability of the secondary level. These room-and-pillar development entries were 2.5 m x 2.5 m (8.2 ft x 8.2 ft) and spaced every 10 m (32 ft), leaving a vertical pillar of 7.5 m (25 ft). First Majestic acquired La Encantada in 2006. After the acquisition of the mine, the company began the conversion of the surveying reference system from a local grid (Maria Isabel Shaft as 0,0) to the Nav27 coordinate system, and subsequently converted to the WGS84 coordinate system in 2015. Due to the extensive history of the mine, different areas were surveyed with different systems, causing significant challenges when designing the principal extraction levels, pillar heights and ramp locations. To overcome this difficulty, the entire mine was resurveyed and the old workings transposed to the new coordinate system, except for some inaccessible areas due to poor ground conditions or ground collapses. To further ensure pillar height and the safety of the mine workers, probe holes were drilled during the development process."

Sep 1, 2019

By William H. Peterson

How is the Government's oil import control program doing? In July 1954 Mr, Eisenhower established the Cabinet Committee on Energy Supplies and Resources Policy. On July 29, 1957, the Administration imposed "voluntary" company oil import quotas on American oil importers to maintain "a healthy domestic (oil) production industry" and safeguard "national security." On March 10, 1959 the President by proclamation made the voluntary program mandatory. But study of the program in practice shows that it is not working out as expected and-that there is some doubt that its aims and other related Administration purposes are being achieved. Take the Administration's anti-inflation policy. To be sure, the President apparently recognized in his March 10th proclamation that in restricting cheap imported oil in favor of more expensive-domestic oil he was making the inflation fight that much harder, for he called for Government surveillance of domestic oil prices to prevent them from getting out of hard, And indeed while domestic crude oil prices have not risen appreciably during 1959 neither have they fallen appreciably (although there has been some price weakness in the past few weeks).

Jan 1, 1960

By D. Hong

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant has been studied. Experiments were carried out in an autoclave. The effect of stirring speed, temperature, pH of the solution, iodine and iodide concentrations on the dissolution of rhenium was investigated. It was found that high temperature and high pH of the solutions were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by mass transfer of iodine with an apparent activation energy of 15.77 kJ/mole.

Jan 1, 1997

By A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in tern of its complexities as well as its value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer based predictions and practical results. Research conducted to compare computer result with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only after more reliable input data are developed.

Jan 1, 1985

By B. Pina

The conversion of maf coal to pyridine solubles and gas was investigated in a microautoclave batch reactor for two Kentucky washed coal samples (Ky. #9 and Ky. #11). Solvent hydrogen donor strength was controlled by the tetralin content of a mixed 1-methyl naphthalene-tetralin solvent. Primary liquefaction conversions greater than 90% in 10 minutes of reaction time at 427°C were achieved in liquefaction solvents with moderate hydrogen-donor strength (circa 40% tetralin). A modified irreversible first order rate expression, containing a parameter (a) to account for the intrinsic reactives of the maf coal, described the experimental kinetic data rather well. The integrated form of this rate expression is -k1e x = a (a- ß)e (eq. 1) Parameter ß in equation (I) is the pyridine solubility of the starting maf feed coal, x is the primary liquefaction fractional number of conversion, k1 is the specific reaction velocity constant and ? is reaction time. Primary liquefaction rate was found to be quite temperature sensitive and independent of coal when a liquefaction solvent containing 40% or more tetralin was employed. Primary liquefaction rate appears to depend on liquefaction solvent hydrogen donor strength for solvents containing = 40 wt.% tetralin. The intrinsic reactives in the maf feed coal or a appear to depend mainly on the inertinite group maceral content of the coal for the two coals studied in liquefaction solvents containing 3 40wt.% tetralin. In contrast, a appears to decrease in liquefaction solvents of low donor strength., i.e; solvents with less than 40wt.% tetralin.

Jan 1, 1984

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By E. H. Christiansen

The most valuable gem- quality red beryl comes from the Wah Wah Mountains of south-western Utah (Fig. 1). Red beryl occurs as a secondary mineral in topaz rhyolite. Marketable crystals from the Wah Wah Mountains have been produced from the Violet Mine, operated on a limited scale since 1976 under the ownership of the Harris family of Delta, UT. From 1989 to 1995, production from the mine amounted to more than $3 million with an inventory of several million dollars of unsold gems (Harris, 1995). In 1994, Kennecott Exploration leased the mine and surrounding claims to determine reserves and feasibility of gem recovery. Mining and exploration activity are continuing. Previous work on red beryl has dealt mainly with crystallographic, chemical and optical properties of the crystals (Shigley and Foord, 1984) with only general descriptions of the geology (Ream, 1979). However, the conditions needed for formation of red beryl have not been well constrained. It is generally proposed that beryl originates by precipitation in fractures and vugs from high-temperature gases as they are released from slowly cooled rhyolite lava. Dozens of topaz rhyolite flows and domes, similar in composition to the beryl-bearing flow in the Wah Wah Mountains, occur across the western United States (Christiansen et al., 1986). All of these flows devitrified to form vapor-phase topaz and locally other vapor-phase minerals such as bixbyite, garnet, hematite, pseudo-broo- kite and fluorite. But the occurrence of beryl is rare. Even within the rhyolite flow that hosts the red beryl, the productive open pits comprise only a small fraction of the surface area of the flow. Apparently, the conditions that favor the formation of red beryl are rarely achieved. Geologic setting The rhyolite flow that hosts the red beryl deposit lies along the eastern flank of the Wah Wah Mountains (Fig. 1). Prevolcanic rocks consist of Proterozoic, Paleozoic and Mesozoic sedimentary rocks that were folded and thrust to the east during the Sevier orogeny. Cenozoic volcanism began about 34 Ma. It consisted mostly of large volume dacitic ash flows and lesser volumes of low- silica rhyolite and andesitic lava flows. Beginning about 23 Ma, the style and composition of volcanism changed to smaller-volume, ash-flow and dome-forming eruptions of high-silica rhyolite and trachyandesitic lava. These rocks form the Blawn Formation of which the beryl-bearing rhyolite is one member (Best et al., 1987). Abbott et al. (1983) reported a K-Ar age of 22.1 + 0.8 Ma for this flow. It is probably the oldest topaz rhyolite flow in the Wah Wah Mountains. A subsequent episode (12 to 13 Ma) of bimodal magmatism produced the Steamboat Mountain Formation. The rhyolitic part of that is locally topaz-bearing. Displacement on the late Cenozoic extensional faults that formed the north-trending mountain ranges began about 22 Ma. Geology of the Violet Mine The rhyolite that hosts the red beryl deposit is part of a flowldome complex that overlies nonwelded tuff of cogenetic origin. This rhyolite is exposed over an area of about 9 km2 (3.5 sq miles) (Fig. 1). An unknown additional portion of the rhyolite is concealed beneath younger mafic lavas and sediments.

Jan 1, 1997

By John Rajala

The Otjikoto Gold Mill was commissioned during November–December 2014 as Namibia’s first new gold producer in 30 years. Its operations consist of surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and gold recovery. The initial mill design capacity was 2.5 Mt/a. Its capacity was expanded after nine months of operation to 3.1 Mt/a, and process performance has significantly surpassed design expectations. After startup, the Otjikoto Mill’s throughput and gold recovery ramped up quickly, with both parameters exceeding design after only two months of operation. The robust process performance continued into 2019, with key performance indicators (KPIs) eclipsing design values in almost every aspect of mill operation. The Otjikoto Mill’s gold recovery is exceptionally high, exceeding 98 percent every year following startup, especially considering the low-grade nature of the deposit.

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel&apos;s No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By Douglas F. Stevenson

Your committee doesn&apos;t assign any easy topics to us speakers. How do you define "successful" in what is essentially a losing game? I am reminded of the fellow who returned from a one-week vacation in Las Vegas, and proudly stated, "I only lost $150." To him, that was "success." I am afraid that workers&apos; compensation is a losing game for employers, too, and success has to be defined in terms of how much or how little is lost. We have no chance of producing a profit for our employer. We will narrow down to some suggestions about conducting a workers&apos; compensation program at the plant level, but first I want to discuss the general legal, social and legislative climate in which your plant program operates. Workers&apos; compensation is a statutory program with its general parameters established by the legislature. These parameters are then amplified by the boards and commissions established to administer workers&apos; compensation. What influences the legislature and the boards and commissions as they establish the framework in which we must function?

Jan 1, 1986

By Georgi N. Shoushoulov, Ventsislav D. Bozhilov

The mining conditions in the Meden Rid mine at levels below 1000 m from the Earth&apos;s surface are specific and rather severe. The rock temperature is about 40-45°C. The air humidity in the workings is approx. 80-90%. There is a limited capacity for additional fresh air supply. The air supply and distribution systems in the mine are very complicated. The airflow recirculation is due to the existing arrangement of the main fans. Certain accidental phenomena are difficult to predict. All these conditions create possibilities for heat and mass exchange between the rock and the air current thus hampering the control of the ventilation and air-conditioning in the mine workings. The changes in the temperature and humidity in certain characteristic places of the development and extraction workings are predicted. The refrigeration output required and the arrangement of the air coolers are also determined. A new ventilation and air- conditioning scherne has been developed. The new ventilation- cooling designs for levels between 1000-1200 m beneath the Earth&apos;s surface are based on the use of portable refrigerating machines having low water flowrate as well as heat-insulating and waterproof materials and methods for preliminary cooling of the orebody within the mining block.

Jan 1, 1997

By Drummond Earley III

The hydrology of in situ leach mining operations is being studied by the U.S. Bureau of Mines using a variety of techniques, and the Bureau has made significant advances in tracking and modeling the flow of leach solutions in rock formations. However, the influence that leach solution composition has on the hydrology of these systems is poorly understood, and geochemically-controlled changes in the hydrologic characteristic of ore deposits during in situ leach mining of porphyry-hosted, copper oxide ores have not been previously studied. The Cyprus Casa Grande in situ leach mining operation mines fracture-hosted and disseminated copper oxides (predominantly chrysocolla) hosted by granodiorite porphyry using a pattern of underground wells. The injection solution consists of sulfuric acid raffinate from a solvent extraction-electrowinning plant. Chemical analysis of representative injection and recovery solutions reveals that gangue cation concentrations in these solutions are high, and geochemical modeling shows that the solutions are saturated or nearly saturated with respect to gypsum, jarosite, and various amorphous oxides. Precipitation of these solids is evoked by calcium-exchange reactions, rising pH, and perhaps locally rising redox potential, as the leach solution reacts with the ore minerals, host rocks, and the atmosphere. Mass and volume balance calculations show that approximately 25 cm of precipitates are formed per gram of copper recovered at Cyprus Casa Grande. The results of geochemical modeling agree with petrologic examination of pre-and post-leach core samples from the leached horizon. Moreover, hydrochemical modeling and hydrologic field data suggests that chemical precipitation causes significant decreases in porosity and permeability during in situ leach mining of porphyry-hosted, copper oxide ore.

Jan 1, 1992

By Olivier Kraft, Olaf Kortz

"Project-specific optimized tunnel boring machines represent the spearhead of technological progress in tunneling because with their use, very long-lasting, high quality tunnel structures in almost any geology, depth and topography can be produced with a high degree of automation. The mechanized excavation of tunnel structures ensures the greatest possible environmental protection during tunneling itself. Professional, systematic and high quality rebuilds and reuse of already proven equipment also ensures maximum efficiency in the use of materials and energy resources. It offers an enormous potential for a highly optimized environmental balance. Here the manufacturers of tunnel boring machines and their users in particular have a duty to ensure transparent, high quality and binding standards in the entire rebuild cycle and in the refurbishment management of innovative tunneling technology. This paper deals with the comprehensive processes with rebuild levels of tunnel boring machines and highlights some exemplarily implemented projects. 1 INTRODUCTION All over the world, the number of tunnel boring machines (TBM) in which equipment rebuilds from previous projects are re-used has increased over the last few years. This text presents the technical and economical aspects of this market development. It also takes a look at the practical implementation of rebuild measures. The ""ITAtech Guidelines on Rebuilds of Machinery for Mechanized Tunnel Excavation"" from 2015 lay down the requirements that the machine manufacturers must meet. 2 ECONOMICAL AND ECOLOGICAL ASPECTS OF RE-USING COMPONENTS The globalization of the construction sector and the consideration of environmental aspects promote an increased re-use of machines and machine components. Nowadays, large-scale construction projects are often carried out by international joint ventures of several individual companies that are established specifically for this purpose. After the completion of the project, the joint ventures are dissolved and they liquidate their project-specific equipment, such as tunnel boring machines. Today, it is much more uncommon for such machines to remain permanently in the possession of construction companies. Joint ventures offer TBMs on the free market, or they exercise contractually agreed repurchase options with the manufacturer. On the whole, this increases the number of re-usable components or complete tunneling systems available on the market."

Jan 1, 2016

By J. B. Griffiths

Clearly there is a tremendous need for assistance in Eastern Europe since most industries must undergo major restructuring. The new governments face many dilemmas, the first task being to establish an order of priorities to deal with the numerous problems at hand. Issues such as the standard of living take low priority compared with market economy and ecological problems. The concept of a Comecon market is now virtually non-existent and trade in roubles ceased from 1991. From this time onwards countries were obliged to trade using free market prices. Governments must also avoid the economic mistakes of countries such as Poland with its high devaluation and lack of economic control and, if possible, contain inflation and unemployment. The privatization of Eastern European enterprises raises considerable difficulties, particularly for large corporations, employing anywhere from 50-100,000 people, which played a major role in the national economy. Whichever method is selected, however, still has to overcome the problem of lack of capital and evaluating the national property. For example, earnings represent only a small percentage of the value of these national industries and thus cannot convert to private ownership without foreign capital investment, either direct or as joint venture capital.

Jan 1, 1992

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey&apos;s Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975