Search Documents

NIOSH recommends that exposures to respirable coal mine dust be limited to 1 mg/m3 as a TWA concentration for up to 10 hr/day during a 40-hr workweek, measured according to current MSHA methods (see Section 5.1 and Appendix J). NIOSH recommends that sampling be conducted with a device that operates in accordance with the NIOSH accuracy criteria [Busch 1977; Busch and Taylor 198 11 and the international definition of respirable dust [ACGIH 1994; CEN 1993; IS01993; Soderholm 1991a,b; 1989].* The REL represents the upper limit of exposure for each worker during each work shift. For single, full-shift samples used to determine noncompliance, NIOSH recommends that MSHA make no upward adjustment of the REL to account for measurement uncertainties [NIOSH 1994c] (see also Section 5.6.2). NIOSH further recommends that all reasonable efforts be made to reduce exposures to respirable coal mine dust below the REL through the use of engineering controls and work practices.

Jan 1, 1997

By Richard H. Oitto

The Bureau of Mines and Kaiser Steel Corp. are cooperatively demonstrating the shield-type roof support in the longwall mining of a 10-1/2-foot-thick coalbed at the York Canyon mine near Raton, N. Mex. As part of the demonstration, the shield supports have been successfully and safely moved from a completed longwall face to a new longwall face. When these shield supports were moved in 1976 they were the largest and heaviest longwall support system in use in U.S. coal mines. The shield supports, preparations for moving them, the actual move, and installation at the new face are discussed.

Jan 1, 1977

By Joseph H. White

In its investigations looking to the improvement of health condi- tions and the increase of efficiency in the mining industry, the Bureau of Mines, in cooperation with the Bureau of Public Health, is studying sanitary conditions in and about mines with the intent of pointing out how those conditions that are a menace to the health of the miner may be most efficiently removed or remedied. An out- line of sanitary betterment work at mining villages in the Birming- ham district of Alabama has already been published by the bureau," and in this bulletin are presented suggestions on the planning of mining towns and the construction of miners' houses. The bulletin does not pretend to be a treatise on the so-called "housing problem," and mentions sociologic issues only incidentally. It is assumed that the influence of proper shelter on health is understood and that not a lack of appreciation so much as a lack of knowledge of the best remedies is responsible for many of the undesirable conditions that exist at mining towns. The purpose of this bulletin is to supply facts on the building of well-lighted, well- ventilated, warm, attractive, and economical houses for miners, these houses being assumed to be units of an industrial village or town the building and management of which are under the control of a corporation, so that special conditions hold which do not apply to houses built and owned by individual miners. From this it is not to be inferred that the company-controlled town is the best system or the only one in vogue. The discussion of this side of the subject in all its phases is too involved to be included in this paper. One element in favor of the company-controlled town is its possible immediate responsiveness. Hence this assumption. Also the assumption is made that a-new isolated town is being built, and hence the selection of the site, the arrangement of the streets, and the situation of the houses are discussed before the house itself is treated, for one of the most important factors in obtaining an economical sanitary house is a well-selected town site. Many of the suggestions, however, may be applied in improving conditions in existing towns, in building new houses in old towns, or in repairing old houses. Emphasis must be laid on the fact that as a rule a mining village has a shorter life than a manufacturing town. Economy is emphasized frequently because the discussion is predi- cated upon the assumption that the miner himself is to pay for all that he gets. House rent will doubtless be expected to bring in a reasonable return on all money invested in streets, sidewalks, water supply, sewer system, and houses; in other words, the town is to be run on a business and not on a paternal or charitable basis. "Fair and reasonable" precludes, of course, the idea of excessive returns. Some companies do not consider it good policy to realize as high a rate of interest as an independent realty company would be war- ranted in realizing. Under some circumstances part of the town improvements might be charged as "expense of the industry," that is, to the consumer. The isolation of a mining town introduces a unique responsibility. As the miners are practically obliged to rent the company houses, the officials of the company ought to scrutinize all expenditures in- volved so that house rent may be reduced to a minimum. In a way the town builders are placed in the position of trustees. They deter- mine, within certain limits, what proportion of a man's wages shall be spent on house rent. This consideration should restrain fanciful and unnecessarily expensive building; the other extreme should like- wise be avoided. True economy should be distinguished from cheap- ness. Ugly, insanitary, uncomfortable shacks should not be built even if, because of their cheapness, there is a demand for them from tenants. The obligation of the industry to society as a whole as well us to the tenant ought to forbid this. A cheerful, strong, healthy, virile race will not rise out of the filth and squalor of cheap hovels. An insanitary environment often does its damage slowly and silently; vitiated air does not, like mine gas, announce its deadly work by an explosion. As Talbot⚫ says: Health depends in part on freedom from infection. The probability of obtain- ing that freedom will be greatly increased by maintaining the body at a high state of vigor, or "vitality," as it is popularly called. This implies the promo- tion of all agencies which have to do with the physical well-being as well as with the control of sources of infection. Many men realize that in building houses for their workmen they are invested with a peculiar responsibility that must be wielded wisely, and in large developments they call into consultation the land- scape architect, the sanitary engineer, and the building architect, as well as the mining engineer.

Jan 1, 1914

By Franklin P. Hall

U.S. supply and demand data for utility electricity by States and regions were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the utility electricity industry that can be integrated into State and regional energy balances by source, form, and major consuming sectors, and used to determine basic flow-patterns. The difficult problem of compiling interstate and interregional shipments of electricity was resolved by (a) assuming the negligibility of interregional shipments and (b) deriving a theoretical line loss percentage used for determining interstate shipments. The data developed were able to show an estimated total supply of utility electricity available for consumption. The tables also report the distribution of the supply among the major consuming sectors (household and commercial, industrial, and transportation). To compare the various energy sources of utility electricity, quantities were converted to their British thermal unit (Btu) equivalents. The Federal Power Commission, Edison Electric Institute, and Bureau of Mines are the sources of the data used in this study.

Jan 1, 1969

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry and seal manufacturers, conducted a series of full-scale experiments within the underground experimental mine at PRL's Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in less than 12 hours and are capable of withstanding explosion overpressures in excess of 140 kPa (20psi). These novel seal designs use available mine materials, do not require conventional rib hitching and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following; questions are arising n the minds of coal users: (a) Will the coal lose any of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when storing coal? In regard to the loss of heating value of coal in storage, tests made by the Bureau of Mines show that the loss commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh Gas, and Sheridan Wyoming coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating; Value of Coal During Storage, by H. C. Porter and F. K. Ovitz:

Jan 1, 1942

By D. Harrington

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protecting exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

Jun 1, 1921

By P. C. Good

The work reported here was undertaken by the Federal Bureau of Mines to investigate new methods of preparing high-purity metal. Tungsten hexachloride was prepared by direct chlorination of scrap tungsten metal and by treating tungstic oxide with carbon and chlorine. The resulting tungsten hexachloride was purified by distillation and reduced win: sodium, magnesium, or hydrogen. The metal prepared by these techniques was at very high purity after arc melting but of variable quality prior to arc meIting. Metal recovery ranged from about 40 to 90 percent of theoretical values, It was found possible to deposit a smooth, dense coating of high-purity tungsten on the inside of a heated tube by vapor-phase reduction of tungsten hexachloride at reduced pressure.

Jan 1, 1961

By A. T. Coumbe

The Bureau of Mines has compiled pipeline mileage every 5 years since 1926, with the exception of the war period 1941 to 1949. The present survey has been made to reflect the progress under mobilization of the petroleum pipeline industry where efforts have been made by the government to stimulate construction of those facilities that would best equip the nation for a possible major emergency. This report summarizes the total mileage change 1n petroleum pipelines for 1950 through 1952. In order to increase the value of the information gathered the reporting companies were requested for the first time to report not only the net change in mileage as formerly, but also all new and used pipe laid and the total taken up. This new information permits effective appraisal of the construction effort of the industry and relates it to steel requirements.

Jan 1, 1953

By Ray J. Holmquist

"INTRODUCTION The Copper King or Red River copper mine was examined on December 13, 1942, by the Bureau of Mines at the request of Richard Kelly of Santa Fe, N. Mex. The examination was made to determine whether the expenditure of funds for rehabilitation work necessary to make the workings accessible for examination would be warranted.As a favorable report was made, the workings of the Copper King mine were opened and sampled under the direction of the author. The portal of the Copper King adit was opened first. Considerable rehabilitation was necessary in the first 50 feet of the workings, but the remainder of the drifts and crosscuts were sufficiently open to permit surveying and sampling.An attempt was made to open the Waterbury atilt, which was reported to be about 30 feet east of the Copper King portal, and to crosscut the ore body nearly to its southern border. However, slide rock and mine dumps had completely obscured the portal of this adit, and no opening into it could be found or made.Work on the project was started on September 27 and vas completed on November 6, 1943."

Apr 1, 1947

By M. M. Tilman

The Bureau of Mines conducted research into the dispersion strengthening of lead by the coprecipitation method. Commercially available reagents in water solutions were reacted to form homogeneous precipitates of lead and aluminum compounds. The resulting precipitates were roasted to oxides and reduced in hydrogen to form mixtures of lead powder and alumina. The powders were isostatically pressed into billets which were extruded into rods. The rods were rolled into strip to provide material for testing. Alloys containing 0.5, 1, 2, and 3 nominal volume-percent A1203 were tested in short-time tensile tests and in tensile creep tests. An alloy of Pb-3 volume-percent A1203 exhibited an average tensile strength of 8,570 psi after rolling to 75-percent reduction at 125° C but had no measurable elongation. Alloys of lower A1203 content provided a better compromise between tensile strength and ductility. For example, an alloy of Pb-0.5 volume-percent A1203 had an average tensile strength of 6,590 psi with 9-percent elongation after rolling to 75-percent reduction at 125° C. Creep rates of dispersion-strengthened Pb-A1203 alloys were below 1 percent in 10,000 hours at stresses of 2,000 to 4,000 psi.

Jan 1, 1971

By M. G. Cherniack, A. J. Brammer, D. R. Peterson

Over the past two decades, there have been significant reductions in industrial exposures to hand-arm vibration, especially when specific tools and work processes have been redesigned to incorporate anti-vibration and ergonomic principles. Nevertheless, Hand-Arm Vibration Syndrome (HAVS) remains a significant occupational health problem as disease symptoms continue to occur even when vibration exposure levels believed to incur low risks have been reached2. This inconsistency may be related to the methodology that is typically used to estimate workday vibration exposure levels, involving laboratory and/or very short duration field measurements coupled with estimates of overall eight-hour tool operation times determined from brief observations of tool tasks and/or self-reported surveys. One solution is to use small, commercially-available, personal vibration dosimeters to calculate, record, and display long-duration vector sums and energy equivalents of vibration. However, since these devices are attached to the worker and require tool-mounted accelerometers, they are incompatible with the worker performing normal duties involving putting down or changing tools. In addition, these commercial systems do not allow for the characterization of the transmission of vibration to the hand such as monitoring the mechanical coupling between the hand and the tool handle (e.g., grip forces). O’Boyle and Griffin showed that variations in applied force can alter vibration transmission characteristics by 50% or more indicating that the measurement of grip force is essential for modeling vibration transmissibility and vibration exposures5. In summary, a need exists for the development of a method and device that will more accurately characterize workday-long vibration exposures. Methods A portable, light-weight, Vibration Exposure Monitor (VEM) system was developed to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of a workday. It monitors frequency weighted and unweighted accelerations from a palm-mounted uni-axial accelerometer (Model 352C22, PCB Piezotronics, Depew, NY) and calculates exposure levels using the root-mean-square (RMS) and higher power mean values, such as the root-mean-quad (RMQ) and the root-mean-oct (RMO). Grip forces are also monitored using a palm-mounted force sensor (Model 400, Interlink Electronics, Camarillo, CA) from which average grip force levels and exerted grip extrema are calculated. At the core of the VEM system is a commercially available, battery-powered microcomputer (Tattletale, Model 8v2, Onset Computer, Onset, MA) with one megabyte of memory and eight analog channels using 12-bit sampling at a single-channel maximum of 100 kHz. Analog signal processing (i.e., anti-aliasing, with cutoffs at 4 and 1250 Hz, and ISO 5349-13 frequency weighting) is accomplished using custom circuitry that is directly interfaced with the microcomputer. An embedded C-based protocol governs the data collection from each channel

Jan 6, 2006

By Wilbur I. Duvall

This paper presents arguments which show that a velocity seismograph should be used to measure building and ground vibrations produced by blasting . However , portable velocity seismographs suitable for this type of measurement are not commercially available . The paper describes how a velocity seismograph can be assembled from commercially available velocity gages , amplifiers , and recorders . Also , specifications are given which could be used in the design and manufacture of a portable velocity seismograph suitable for measuring vibrations from blasting .

Jan 1, 1964

By V. A. Nieberlein

Problems of design involving the high-temperature characteristics of materials of construction have focused attention on tungsten, the metal with the highest melting point. To study the properties of this metal a method was needed to produce tungsten of high purity easily and consistently. The Bureau of Mines has made tungsten metal in massive form on a laboratory scale by hydrogen reduction of tungsten hexafluoride (WF6). Metal made in this manner had a purity of 99.99 percent or better, with reference to all detectable impurities, including gases. The process tolerated a wide variation in operating conditions, and the results with respect to total impurities as low as 0.01 percent were reproducible.

Jan 1, 1959

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

By John Durkin

Owing to the daily exposures of uranium mining personnel to 222Rn daughters, a device is needed that will continually monitor individual exposure. Such a device has been built and tested by the Bureau of Mines and is known as a radon daughter dosimeter. This is an electronic instrument using a solid-state detector and circuitry. The concept of the instrument, which is a personal device worn throughout the working shift, is to evaluate an individual's cumulative exposure to airborne radon progeny, expressed in units of working level hours. Since the instrument is in close proximity to the miner and measures continual exposure, it avoids the errors caused by the present technique of spot checking of the environment and provides a more accurate account of total cumulative exposure.

Jan 1, 1977

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By Charles H. Shapiro

[In July, 1924, the Bureau of Mines, through its Petroleum Experiment Station, undertook a field study of methods used in oil-field shops for dressing and tempering fishtail bits. The purpose of this work was to suggest chances that would be helpful to the bit-dresser in turning out better treated, harder, and tougher bits, and thus cut down the excessive loss of time caused by too frequent changing of bits. It was the intention to eliminate as much as possible the guess work connected with dressing and tempering bits under the method of judging temperature by eye, by developing; practical methods of controlling temperature. If there were some possible means of accurate temperature control, then it would be an easy matter to bring all bits to the proper temperature for maximum hardness rued toughness, thus doing away with the source of most of the trouble experienced in the present method of bit tempering. Shortly after the Bureau of Mines began its study, a chop In the Stroud, Oklahoma, oil field announced method for tempering fishtail bits that Would increase the drilling footage of each bit treated. The method accurately regulates, by the use of a bath of molten salt, the temperature to which a bit is heated before being quenched to produce hardness. There is nothing new in using silt baths for the, heat treatment of steel, but this was the first attempt to introduce it into the oil fields for use in hardening bits, and for this purpose it proved to be admirably adapted. In tempering, by the old system it is not possible to measure the temperature of the heated bit by means of an electrical instrument for that purpose, whereas this is an easy matter with the now method. If heating steel to slightly above the critical point rind quenching suddenly will bring out its best properties, their here is a method of accurately bringing the steel to that point.]

Jan 1, 1925

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005