Search Documents

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"Abstract — The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH ) regards ""wholediesel exhaust"" as ""a potential occupational carcinogen."" Threshold limit values (TLVs ) are recommended for the gaseous pollutants CO, CO2, NO, NO2, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sample these aerosols.The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, partial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine a quality.Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulage way and on haulage vehicles. Both full- and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO,CO2, NO, NC, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.Concentrations of CO, CO2, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m4, with a standard deviation of 0.19 mg/m3 DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 022 mg/m3."

Mar 1, 1992

By R. F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Bureau of Mines has developed a general method for preparing solutions from a wide range of metal and mineral samples for chemical analysis. The development of the method from current knowledge of vessel material, pressure dissolution techniques, and the fluoride-boric acid reaction is given. The method uses 7 ml of a mixture of HC1-HNO3-HF acids in a ratio of 3.5:2:1.5 sealed in plastic bottles that act as pressure vessels when heated in a boiling water bath. A final volume of 100 ml is obtained by the addition of 93 ml of a 1. 5-pct H3BO3 solution to the bottles, which are reheated; precipitated fluorides as well as sample residue are dissolved by the fluoride-boric acid reaction. A copper slag and a steelmaking slag treated using this method were analyzed by atomic absorption spectroscopy yielding values for Si, Mg, Ca, AI, Fe, Mn, Na, As, Pb, Sb, and Zn very close to certified values with an average relative standard deviation of 2.13 pct. The low cost, reduction in preparation time, ease and safety of sample handling, conservation of reagents, and ability to dissolve volatile materials without loss make this method superior to traditional wet digestion techniques for many materials, and ideal for use with atomic absorption, and optical emission or X-ray emission spectroscopy.

Jan 1, 1980

By R. C. Butman

The Lincoln Terminal System (LTS) is a stand-alone computerized training device that presents high quality visual displays, and audio messages to a student. A keyboard is provided for student input. A variety of student-machine interactive programs arc provided. These programs allow the author/instructor to evaluate numerical entries and responses to simple and compound multiple-choice questions (where a compound choice is defined to be more than one choice, ordered or unordered from one or more list(s) of choices. Descriptions of LTS applications, lesson development procedures, hardware provided and support facilities required are given. A contract history summary, and a bibliography of reports published under three successive BoM contracts supporting LTS development, is provided.

Jan 1, 1979

By Potter G. M.

Ore-dressing tests were conducted on a sample of ore submitted by the Richmond Hill Mining Co. of Lead, S. Dak. as a part of the Bureau of Mines program for investigating potential domestic sources of manganese. Half of the sample was taken from the 300-foot level and half from surface cuts. The problems involved were liberation and rejection of silica and iron and removal of lead, Silver, and gold from the manganese concentrates. Although a portion of the silica and iron oxides was too intimately associated with manganese minerals for rejection by ore-dressing methods, thus limiting recovery of high-grade concentrates, the Richmond Hill ore was found amenable to simple gravity methods of concentration for producing intermediate-grade products. By jigging and tabling, 73.8 percent of the total manganese was recovered in a product that, when sintered, assayed plus 40 percent Mn. Lead, silver, and gold were successfully removed from gravity concentrates by a chloridizing roasting treatment.

Jan 1, 1948

By J. S. Malesky

"INTRODUCTION The Airdox method of breaking coal utilizes compressed air under high pressure and was developed to replace explosives. It is used in Illinois and Indiana mines to a large extent and also has been introduced in mines in a few other States.ACKNOWLEDGMENTThe author gratefully acknowledges the information and photographs furnished by the Cardox Corp.HISTORYIn the early 1920's, with the adoption of mechanical mining in States where on-shift shooting was prohibited, it became desirable to develop some means of breaking coal from the face without the use of explosives. At that time it was thought that a pressure of 20,000 pounds per square inch would be necessary to break the seal. It was impossible to obtain a compressor that would develop this pressure therefore, the 'patentees developed and applied the Cardox method, which utilizes liquid carbon dioxide as the blasting medium."

Aug 1, 1948

By Van H. Manning

"Under the organic act establishing it, the Bureau of Mines is authorized to conduct investigations designed to improve health and safety conditions in the mineral industry and to promote efficient development and utilization of our mineral resources. The field of the Bureau's activity, therefore, begins with the commercial development of mineral deposits and ends with the production and utilization of the final marketable product.In order to serve more efficiently the various sections of the country, the Bureau has established, in addition to its main offices at Washington, D. C., eleven field experiment stations, three field offices and several mine rescue cars and mina rescue stations. These field branches are so distributed as to cover most of the mining districts of this country, including Alaska. The field service in general deals with specific experimental problems, cooperative work with non-governmental institutions, and mina rescue work, while the Washington office is the administrative head and is responsible for the distribution of general information, the chiefs of the technical and administrative divisions of the Bureau being stationed there.The Bureau is prohibited by law from doing work exclusively for the benefit of any private company or individual. Generally speaking, the Bureau does no assaying, ore testing, or similar service work for the benefit of private companies or individuals. In response to requests for work of this sort a list of assay and ore testing laboratories is supplied. In referring inquiries to com-mercial laboratories or consulting engineers, care is taken to mention several names so as to avoid designating any one establishment or engineer."

Apr 1, 1920

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

By P. H. Floyd

Laboratory test work has shown that the Germania ferberite-scheelite ore can be concentrated to an acceptable grade. A ferberite concentrate assaying 66.9 percent tungstic oxide was made, with a recovery of 75.4 percent. A second concentrate of ferberite and scheelite was made assaying 54.2 percent tungstic oxide. Final beneficiation of combined rougher gravity concentrates was accomplished by roasting, magnetic separation, sulfide flotation, and retabling, to give a final ferberite-scheelite concentrate of 66.2 percent tungstic oxide, with a 91.1-percent recovery. INTRODUCTION This presentation covers the results of laboratory beneficiation tests conducted on tungsten ore from the Germania Consolidated Mines, Inc., by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg. This mining property is near Fruitland, on the southern edge of the Spokane Indian Reservation, Stevens County, Wash. The Germania district produced tungsten concentrates before and after World War I; interest is being renewed in the district because of the metal shortage.

Jan 1, 1954

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation's mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

1. In 2002, a total of 763 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Examples of nonmetal mining operations include the mining of clay, trona, barite, phosphate rock, gypsum, talc, gemstones, and pumice. Nonmetal mines comprised 5.3% of all mining operations. • Nonmetal mining operations are located in all but nine states or territories (Alaska, Delaware, Maine, New Hampshire, Rhode Island, Vermont, Wisconsin, Puerto Rico, and the Virgin Islands). • Mines producing common clay comprised 29.2% (n = 223) of all nonmetal mining operations.

Jan 1, 2004

By Donald F. Reed

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling from October 1247 to March 1948 at the Pickering Creek deposits, Charter County, Pa., in an endeavor to find an additional source of supply of lead and zinc. Lead mining in Pickering Creek Valley showed great activity from 1851 to 1855; but after this period mining gradually declined until 1870 when all mines were. One small mine did some work from 1917 to 1920. The ores were sulfides of lead and zinc, which were partly oxidized from the surface to the 20-foot level. As zinc was penalized at the reduction works, the ore was sorted at the mine and the zinc discarded. The Wheatley and Chester County veins contained the beet ore bodies in the district. These converging veins are 2 to 5 feet wide. To cut the veins below the old mine working' the Bureau of Mines diamond-drilled eight holes aggregating 2,820 feet. No significant lead-zinc mineralization was found.

Jan 1, 1949

By F. S. Crawford

Interesting data on electric blasting and sinking of the Montreal No. 5 shaft of the Montreal Mining Co., Montreal, Wis., were obtained during the sinking of the last 877 feet of this shaft. Several unusual features and safety practices are also to be found in the Montreal mine. The Montreal shaft was sunk 2,156 feet from August 16, 1921, to May 1, 1924, and 877 feet from October, 1927, to June, 1928. The first section of the shaft was supported with steel sets spaced 5 feet on centers; and instead of lagging the walls were covered with three-eighths of an inch of gunite where Greenstone was encountered, and where quartz-slate was found (from the surface to the 12th level) the walls were lagged with tamarack lath treated with carbolineum, a preservative.

Jan 1, 1929

Introduction The Coal Mine Roof Rating (CMRR) is a roof classification system. It was first introduced to the mining community in 1994.The CMRR filled a longstanding need to quantify geologic description of coal measure rocks into an engineering value that could be used for mine design. It has now been written to a user-friendly visual basic code that can be run on any PC with a Windows operating system. Background Rocks that form the roof of coal mines can vary widely and quickly in composition, extent, and defects. This results in an equally broad range of rock properties that can substantially affect the ability of the rock mass to form a stable mine roof. The CMRR was designed to evaluate the properties of the coal mine roof rock mass that contribute to its weakness and convert them into a relative strength rating from 0 to 100. These properties include the cohesion and frequency of discontinuities like bedding, slips, shears, and joints; uniaxial compressive strength (UCS); and moisture sensitivity. With simple lab and field tests and observation, the CMRR can be calculated by technical and operating personnel with a minimum of training. The CMRR has been widely accepted in both U.S. and international coalfields. As a result, a number of roof control applications have been found for the CMRR. It is currently used as an input component in the Analysis of Longwall Pillar Stability(ALPS) program, which is used to design longwall chain pillars. Incan be used as a criterion for determining the appropriate width of mine entries. It has also been used to indicate the appropriate length of cut in weak ground. The CMRR can be used as a strength parameter to characterize inter burden between mined seams in the numerical modeling of subsidence effects. In any area where an estimation of coal measure rock mass strength is required, the CMRR can be adapted to fill this need. How It Works Originally designed to be used with underground exposures, the CMRR can also be calculated from core. The chisel test for bedding cohesion and the ballpeen hammer test for UCS are inappropriate for core. These tests have been replaced by point load testing both axially and diametrally. Two other measures that are common to standard core logging—Rock Quality Designation (RQD) and fracture spacing—are also used to estimate rock weakness. With these easily obtained parameters, the CMRR can be calculated from core and used in the mine planning and exploration phase. The input screens allow calculation of the CMRR for both underground exposure and core. The CMRR is reported both as a “dry" value and as a groundwater-adjusted value for moisture-sensitive rocks. There is a graphical output report featuring a lithologic column with annotated unit ratings and a roof bolt symbol representing the height of the bolted horizon. Another important feature is an AutoCAD interface. This feature allows the export of located CMRR data directly to an AutoCAD layer in XYZ form. In this way, drill hole data can be inserted directly to a base map.

Apr 1, 2003

By Nick Derick

The continued growth of steel production in the Western States is contingent upon the development of new iron ore sources. Recent development of economical techniques for concentrating and agglomerating taconites has focused attention on the low-grade magnetite deposits near Atlantic City, Wyo., as potentially important sources of iron ore for blast furnace smelting. Therefore, the Federal Bureau of Mines has made comparative evaluations of blast furnace burdens that incorporate pellets produced from Atlantic City concentrates. The Bureau also has evaluated the relative effect of Utah coke on blast furnace performance, using a high-quality Eastern coke as a basis for comparison. This work was done in the Bureau's experimental blast furnace at Bruceton, Pa. Tests determined the maximum wind rate that could be used while a continuous stock movement was maintained in the furnace. The furnace was operated at wind rates ranging from 800 to 1,400 std. c.f.m., them maximum limit of the blowers for the 1.75 in.-diameter tuyeres used. Using a normal Utah ore burden and Utah coke, the furnace went into a tight hanging condition with a wind rate above 950 std, c.f.m. Using the experimental pellet burden again with Utah coke, the wind rate could be increased to 1,000 std, c.f.m. and probably to 1,050 std. c.f.m, before tight hanging occurs. This represents an increase of 5 to 10 pct. in the wind rate. The experimental results indicate an accompanying increase of iron production, as much as 8 pct.

Jan 1, 1961

By J. M. Kuchta

Experimental data are presented on the autoignition temperature (AIT) characteristics of the hydrocarbon jet fuel, JP-6, in various oxygen-nitrogen atmospheres under conditions of constant volume and constant pressure. AIT's of this fuel in air varied little with fuel injection pressure but increased greatly with decreasing fuel content at low fuel-air-ratios. They also increased with decreasing oxygen content of the fuel vapor-oxidant atmosphere. Consistent with thermal ignition theory, the ignition temperatures increased with decreasing initial pressure, ignition delay, and vessel radius; expressions are given which define the observed variation of AIT with these variables for JP-6 fuel vapor-air mixtures. The significance of autoignition temperature data obtained using various ignition criteria is discussed to show the usefulness of such data in evaluating fire and explosion hazards. In addition, data are presented on the extent of oxidation that occurs prior to autoignition of this fuel in air at various temperatures.

Jan 1, 1965

By H. A. Johansen

Recent advances in the metallurgy of chromium have enabled this metal to begin to take its place among the refractory metals. Considerable work is being done on the development of high-temperature alloys containing high percentages of chromium.1/2/ In spite of the relatively large amount of work done on these alloys, little is known of the properties of the pure metal. Information in the literature concerning the tensile properties of pure chromium metal is quite scant. This deficiency maybe explained by the great difficulty of preparing test specimens from such a brittle material, resulting in many losses in each phase of the specimen preparation and testing procedure.

Jan 1, 1954

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

Create two air splits along the longwall face to isolate the shearer-generated dust to the immediate face area, maintaining a cleaner split of air in the workers' walkway.

Jan 1, 1994