Search Documents

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By Lloyd M. Kniffin

[This paper is one of series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United States. It describes the mine of the Hanover Bessemer Iron & Copper Co. at Fierro, Grant County, N. M., which is the only operating iron mine in the southwestern part of the United States. This mine is in a district noted for the great variety of ores that it produces. Within a small area, as shown is Figure 1, there are noteworthy deposits of nearly all the common metals. The ore occurs in lenticular masses dipping at about 50°. An underhand stoping method has been developed that requires but a very small amount of handling of ore. As the ore is very irregular in iron content and also in the distribution of the impurities--chiefly sulphur, silica, and magnesia--a method has to be used that will permit selective mining and will also allow ore and waste to be taken out separately as conditions change. A magnetic cobbing plant raises the grade of the ore shipped about 10 per cent.]

Jan 1, 1930

By James H. Scott

Well-logging techniques that have been used to evaluate various types of mineral deposits are discussed briefly, and many pertinent references are cited. Information is categorized by mineral commodity to make it easy to determine what logging techniques have been used for evaluating specific metals and nonmetals. Part 1 discusses logging techniques applied to deposits of the following metals: aluminum, antimony, beryllium, boron, copper, iron, lead and zinc, maganese, mercury, nickel, silver and gold, tin, tungsten, and uranium. Part 2 covers the following nonmetals: coal, evaporites, fluorspar, oil shale, rock salt, and sulfur. Separate bibliographies are given for English and foreign language references.

Jan 1, 1974

By R. V. Ramani, R. Srikanth, R. Zhao

"A two-pan study was conducted to understand the factors affecting respirable dust generation potential or dustiness of coal seams. In the first part, the data from three prior comprehensive laboratory studies was analyzed to establish quantitative relationships between respirable dust generation potential and coal characteristics. This analysis indicates that respirable dust generation rate is positively correlated with Hardgrove Grindability Index (HGI), fuel ratio (fixed carbon/volatile matter), Vitrinite Reflectance (VR), and Level of Organic Metamorphism (LOM). In the second part, specially-designed single breakage experiments were conducted to determine the primary dust generation potential of 17 coal samples obtained from four continuous miner sections, three longwall sections, and the Penn State Coal Data Bank. The single breakage study indicates that primary dust generation rate is positively correlated with fixed carbon content, fuel ratio (fixed carbon/volatile matter), VR, and LOM. Since VR and LOM are strongly influenced by the process of coalification, differences in respirable dust generation rates in different coal seams may be explained by the thermal metamorphism of sedimentary organic matter during subsurface burial.Mineral particles in the range of one to five microns, if inhaled in sufficient amounts, lead to a number of lung diseases generally referred to as pneumoconiosis. A priori knowledge of the mechanisms and rates of fine particle generation during mining can aid in the development of more effective technology for controlling primary dust generation. Unfortunately, the data and knowledge currently available are not adequate for this purpose. In fact, a committee of the National Academy of Sciences on the measurement and control of dust concluded that the knowledge of the fundamental mechanisms by which coal mine dust is generated and a part of it is entrained in the mine atmosphere as respirable dust is not sufficient to clarify, let alone control, the processes involved (Anon., 1980). Under a research contract from the U.S. Bureau of Mines, Stecklein et al. (1982) have identified a number of fundamental research issues for understanding the coal fragmentation and entrainment processes.Reduction of dust generation is the best means of control since fine particles are difficult to control once they become airborne. Therefore, considerable research efforts have been directed to understand the factors influencing dust generation and entrainment, including machine design, water sprays, and ventilation. Laboratory studies have been conducted on the mechanical action of bits and machine power requirements (Evans and Pomeroy, 1966; Roepke, 1984). Since the physical characteristics of coal play an important role in the process of breakage, a number of laboratory studies have been conducted to study the relationship between coal characteristics and respirable dust generation (Baafi, 1977; Moore, 1986; Polat, 1990; Thakur, 1971). Several studies have been conducted on the relationships between coal characteristics and airborne dust concentrations (Hamilton and Knight, 1958; Khair and Xu, 1991; Organiscak and Page, 1993; Page et al., 1993). A limited number of studies have also been conducted on the relationships between coal characteristics and airborne dust concentrations in mines (Organiscak et al., 1990). Yet, no reliable method has been developed to rank coal seams according to their respirable dust generation potential. The conclusions derived from previous studies can be summarized as follows:"

Dec 1, 1996

By Jack E. Fraley

In this Bureau of Mines study, sealants containing mineral wool, cement, etc, were sprayed through dry-process equipment that propels dry material pneumatically to the water-adding nozzle. Advantages over slurry applications include no mixing, no extensive cleanup, and freedom from hardened cement in equipment should power be lost. Sealants with large mineral wool nodules (>l-inch) were sprayable at rates to 900 square feet per hour for 1/2-inch thickness with little dust and smooth material flow through equipment, but they were weak for mine use, Materials containing small wool nodules (1/4-inch) were stronger but tended to plug lines because the nodules were inadequately separated in the shredder. Increasing the dedusting oil also increased line plugging by holding the nodules together in larger lumps. Best results were obtained using a 3/4-inch-nodule wool with cement binder, which provided both smooth flow through the machine and adequate strength.

Jan 1, 1977

By S. S. M. Chan

The Bureau of Mines has investigated the structural aspects of shafts and support systems using the finite-element technique. In situ field measurements in deep, vein-type metal mines show that rock stresses are often higher in the horizontal direction than the vertical, and unequal in the horizontal plane. These data and laboratory and field-determined physical properties were used as input to analytical studies. Various design and construction parameters were investigated to deter-mine the effect on shaft stability. Rectangular shafts were studied in detail to determine the effects of applied stress ratio, shaft orientation and dimension, influence of interbedded quartzite and argillite, and rock fracturing. Various support systems were analyzed, including concrete lining, timber, and steel sets. Circular configurations were investigated to evaluate yield zones and liner thickness. Elliptical shafts and time effects were briefly evaluated to illustrate shape and time effects and demonstrate the methodology. It is shown that the magnitude, direction, and ratio of applied stress and rock mass anisotropy are keys to determining shaft stability. A realistic conceptual framework was developed with which to examine the rock and support interaction in deep mine shafts. Structural analysis techniques overcome some of the historical difficulties with shaft de-sign by defining the field data requirements and structural sensitivity of various design and construction parameters.

Jan 1, 1985

By Leon E. Esparza

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 16,927-acre Pryor Mountain Wilderness Study Area (MT-067-206), part of the 3,955-acre Burnt Timber Canyon Wilderness Study Area (MT-067-205), and part of the 4,550-acre Big Horn Tack-On Wilderness Study Area (MT-067-207) to evaluate their identified mineral resources. The Burnt Timber and Big Horn Tack-On study areas contain 3,430 and 2,550 acres, respectively. The three areas are in Carbon County, MT, and Big Horn County, WY, about 13 miles north of Lovell, WY. No identified resources exist in any of the study areas. Bureau of Mines personnel reviewed literature, searched county mining records and examined prospects, claims, and mineralized areas to determine whether identified mineral resources existed. The three study areas are within the Pryor Mountain unorganized mining district. U.S. Department of Energy production records indicate there were 223,000 pounds of uranium oxide (U308) and 236,000 pounds of vanadium pentoxide (V205) produced from 19 properties within the mining district. The average ore grade was 0.36 percent [3,600 ppm (parts per million)] U308 and 0.416 percent (4,160 ppm) V20S. Only the Pryor Mountain study area has current claims, the 50 claims of the S0S group.

Jan 1, 1986

By Laurence F. Kelley

This paper is one of a series being prepared by the United States Bureau of Mines on shaft-sinking methods and costs at individual operations in various mining districts of the United States. The methods and costs described herein are those of The Consolidation Coal Co. at one of its operations in the Tug River district, McDowell County, W. Va. ACKNOWLEDGMENT The author is indebted to Frank R. Lyon, vice-president, Thos. G. Fear, general manager of operations, and Chas. Enzian, chief engineer, of The Consolidation Coal Co., for valuable assistance and collaboration in the preparation of this paper. W. A. Cole, manager of the E. J. Longyear Development Co. furnished valuable data on methods and performance averages.

Jan 1, 1932

By H. P. Hermance

The Ore Hill zinc-lead mine in Grafton County, N. H., was investigated by the Bureau of Mines from March to July 1943 and from August to October 1944. Fourteen holes with an aggregate bore of 4,899 feet were diamond-drilled, the old workings were unwatered and sampled to an inclined depth of 250 feet, and the tailings dumps were surveyed and sampled. The deposit at the Ore Hill mine comprises a bedding-plane vein of massive sphalerite and galena with subordinate chalcopyrite and pyrite in a series of interbedded metasedimentary and metavolcanic schists about one-quarter mile east of their contact with the intrusive Baker Pond gneiss. The property was first opened about 1850 and was active at times to 1914. Production records are not available, but the output is believed to have been considerable. In 1944, leasers recovered a marketable mica product from mica schist from the dumps and certain outcrops. This report describes the work performed in the Bureau's investigation and presents the data obtained.

Jan 1, 1948

By S. C. Schaefer

Thermodynamic properties of indium oxide (In203) have been studied with a high-temperature galvanic cell employing stabilized zirconia electrolytes. In the temperature range 790° to 1,230° K the free-energy change for the cell reaction 21n(1) + 3Cu20(c) = In203(c) + 6Cu(c) together with the standard free energy of formation of cuprous oxide gives the standard free energy of formation of indium oxide from the elements as ?Gf° = -218.78 + 75.34 X 10-3T ±0.7 kcal/mole. A third-law analysis yields the standard enthalpy of formation: ?Hf°298.15 = -221.5 kcal/mole.

Jan 1, 1971

By J. G. Walters

In 1928, the Coal Carbonization Section of the Federal Bureau of Mines, in cooperation with the American Gas Association, began a survey of the carbonizing properties of American coals. A standard test method for evaluating the carbonizing properties of coals that met the following conditions was developed: To yield products similar to those obtained in commercial operations. To produce yields sufficient to permit analyses and tests of quality. To be laboratory size. To be convenient to operate. To permit reproducible control of test conditions and results. This test method has become known as the Bureau of Mines-American Gas Association (BM-AGA) test (53),3/ and more coals of greater variety have been tested in this apparatus than in any other of similar scale.

Jan 1, 1961

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By W. D. Mcmillan

Although the Shafter district of Presidio County, Tex., is principally renowned for silver production from the Presidio mine, the occurrence of lead-zinc ores in the western part of the district has been known for at least 50 years, and there has been some production. An area of about 3 square miles in the vicinity of an extending westward from the Presidio mine was investigated in detail by C. P. Ross of the Federal Geological Survey in 1934. In the fall of 1943, A. B. Needham, an engineer of the Bureau of Mines, called the attention of the Geological Survey to the area west of that included in Ross's map, and requested a detailed investigation of that area by the Survey in advance of development by the Bureau of Mines. After a brief reconnaissance by the Survey in the spring of 1944, detailed studies were made by Federal geologists in the summer of 1944, during which about 450 acres were surveyed, on a scale of 1 inch to 100 feet. Recommendations for the exploration of certain parts of the area were made in the accompanying report.

Jan 1, 1949

By John Nagy, Austin R. Cooper, Murray Jacobson

Data obtained in the Bureau's study of dust explosions of 313 elemental metals , alloys , catalysts , and ores comprising 54 types of material are summarized . Information is given on ignition temperature , spark energy for ignition , minimum explosion concentration , explosion pressure , rate of pressure rise , and in some instances , the admixed inert dust and oxygen concentration in an atmosphere required to prevent ignition of dust dispersions . The effects of particle diameter on explosibility and pyrophoricity are also discussed .

Jan 1, 1964

By Harold J. Barnett

In January 1948 , the Secretary of the Interior directed that a study be made of energy resources and requirements that would provide a basis for continuing appraisal of the adequacy of the Department's programs in the energy field . That this instruction was timely has been demonstrated by the increasing interest being evidenced by Congress , industry , labor , and the public in the future of the energy segment of our national economy . Several studies of individual energy sectors have appeared . Various legislative proposals have been made in Congress for obtaining more information on this subject . Substantial interest in energy projections is not , of course , a recent innovation . Energy availability and consumption are strategic factors in peacetime prosperity and growth and in our national defense as well . The past generation's literature of earnest public discussion and of legislative consideration of matters involving energy projections is very extensive . This is an exploratory study produced in the Program Staff of the Office of the Secretary of the Interior in the first half of 1949 and revised recently to take account of certain of the preliminary energy data from the 1947 Census of Manufactures and critical comments . It is offered at this time solely as a technical contribution in economic research technique . As the Bureau of Mines has recently undertaken to revise this preliminary study , critical and other comments are invited .

Oct 1, 1950

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010