Search Documents

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

By B. W. Gandrud

This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests made by the Bureau of Mines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers The Klondyke mine, operated by the Blocton Mining Co., is about 1 mile east of West Blocton, Bibb County, Ala., near the southwestern extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/, one on the tabling of fine coal from the Thompson and Woodstock bed , and the third a washablility study of the Henry Ellen bed at Acmar6/.

Jan 1, 1939

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners&apos; safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

In 1987 Wyoming became the largest coal producing state in the country. The state is known for its extensive coal resources and extremely thick coal seams. Wyoming&apos;s coal reserves total about 69.3 billion tons, or 14.2 percent of the U.S. coal reserve. Coal seams range generally from 10 to 80 feet in thickness, although one seam is 220 feet thick. The coal-bearing areas of Wyoming underlie approximately 41 percent of the state&apos;s total land area. Wyoming&apos;s coal ranges from lignite to high volatile bituminous. Most of the coal produced is subbituminous from the Powder River coal region near Gillette. The presence of coal in Wyoming was discovered before 1834 on the Belle Fourche River. The state&apos;s first mine opened in Carbon County in 1865, and with the completion of the trans- continental railroad, the demand for coal increased. Currently approximately 80 percent of Wyoming&apos;s coal production is shipped out-of-state to meet the growing demand for low- sulfur coal to fuel electric generating plants. Wyoming received conditional regulatory approval November 26, 1980. Its Abandoned Mine Land Program was approved February 14, 1983.

Jan 1, 1992

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a part of the 21,296-acre Million Hills Wilderness Study Area (NV-050-233) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 46 miles south of Mesquite, NV. The area is on the east edge of the Gold Butte mining district and has had minor production of copper and zinc from the Azure Ridge mine in the early 1900&apos;s. Assessment work was being done on the Esperanta claims, which covers the mine workings, in March 1987.

Jan 1, 1988

By Harold E. Marr

A simple algorithm is presented for processing digitized X-ray spectra obtained with a Si(Li) or Ge(Li) semiconductor detector coupled to a multi- channel analyzer. The simplified least-squares procedure is used to smooth out the statistical fluctuations in the spectrum by repeatedly fitting a quad- ratic equation to a predetermined number of channels and performing a traveling smooth across the spectrum. A logarithmic transform is applied to the raw data to minimize the distortion of the gaussian-shaped peak profiles. The efficacy of the technique is evaluated by observing the distortion of several gaussian-shaped peaks that have been subjected to the smoothing operation. The locations of maximums and minimums in the spectrum are predicted in the process as well as the values of the peak heights. The convolution integers from a least-squares fit of a quadratic equation are calculated as part of a FORTRAN subroutine. The building-block approach to computer programing in a small laboratory is discussed.

Jan 1, 1972

By Travis Q. Lyday

During 1983, Ecuador&apos;s gross domestic product (GDP) decreased by a reported 3.3% in real terms, the second consecutive decline in the economy after more than a decade of growth generated mainly by petroleum export revenues. The slowdown was due, in part, to the effects of the world recession, lower foreign demand for oil, depressed world oil prices, and reduced demand and prices for Ecuador&apos;s traditional agricultural exports. Inflation accelerated to an estimated 55% annual rate. The sucre was devalued in March, for the second time in less than a 12-month period, by 27% after remaining unchanged during the previous decade. In addition, continuous adjustments were made every weekday, effectively devaluing the sucre another 30% by yearend. Ecuador&apos;s production of crude petroleum increased almost 12% in 1983 compared with that of 1982. Average daily production was 237,100 barrels per day (bbl/d), up from 211,300 bbl/d in 1982.

Jan 1, 1985

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Hand arm vibration syndrome (HAVS) affects industrial workers exposed to long term hand-transmitted vibration from powered-tools. Peripheral neuropathy is a major component of the symptom complex of HAVS. Long term exposure to vibration causes myelin damage in peripheral nerves and reduces nerve conduction velocities in rats1. This study addresses the effects of acute vibration at constant acceleration of 49 m/s2 on myelinated fibers in peripheral nerves in Sprague-Dawley male rats using the ‘rat-tail vibration model,’ which simulates hand-transmitted vibration2. Methods Male Sprague-Dawley rats (~300 g) were assigned to vibration groups: 1 hr continuous vibration at 60 Hz; 4 hr continuous exposure at frequencies of 30, 60, 120 or 800 Hz; immediate and 24 hr following a 4-hr cumulative exposure of continuous and intermittent vibration at 60 Hz. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage accelerated by a B&K motor type 4809 and vibrated. Intermittent vibration was delivered in bouts of 10 min vibration alternating with 5 min rest periods repeated over 6 hr. Sham controls were restrained without vibration. After vibration exposure, the rats were anaesthetized, and the ventral nerve trunks from the proximal tail segment 7 were fixed in glutaraldehyde, embedded in epon-araldite and sectioned at 0.5 µm thickness and stained with toludine-blue for morphological quantitative analysis. The total number of myelinated axons in each cross-section of the nerve was counted using the Image J software. Myelin damage was identified by focal increase in area and intensity of toludine-blue staining and unraveling of the myelin sheath. Statistical analysis for comparing sham and the different vibration groups was done using Dunnett’s test. Animal treatment and all surgical procedures were approved by the institutional review board and compiled with the Laboratory Animal Welfare Act. Results The rats tolerated continuous vibration very well and exhibited no behavioral signs of stress. When exposed to intermittent vibration, there was increased vocalization, a startle reflex at the beginning of each bout of vibration, deposition of porphyrin around the eyes and transient hypersensitivity to touch.

Jan 6, 2006

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By P. R. Jones

The Bureau of Mines has written a computer program for the design and cost of a shell and tube type heat exchanger, in which a change in phase occurs on the shell side. The total cost, which was minimized, includes the annual fixed charges and annual operating costs. The program was written to meet the following requirements: (1) Triangular pitch, (2) single or multiple pass, and (3) heating or cooling. Price optimum design was obtained for four standard tube diameters and pitch. Standard heat exchangers whose area equaled or exceeded the required area are also listed. The program was made adaptable to various fluids and to various tube dimensions by including many of the required data such as physical properties of the fluids, tube data, and standard shell data as input data.

Jan 1, 1969

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By M. M. Wong

Beryllium possesses attractive properties for use in the nuclear and space fields. Since fused-salt electrorefining can be employed to produce this metal in high-purity form from low-grade or scrap metals, the Bureau of Mines investigated electrorefining of beryllium in electrolytes composed of a LiC1-KC1 eutectic mixture plus varying amounts of BeC12. Results showed a 99- percent or better reduction of oxygen and magnesium and a substantial reduction of other minor metallic impurities. Extremely pure beryllium metal was produced. Operating variables, including BeCl2 concentration in the bath (3.5 to 16.5 mole-percent), temperature of operation (450° to 550° C.), and cathode current density (45 to 770 a,/sq, ft.), were studied; their effects on the deposition of metal, working condition of the bath, and purity of the refined metal are discussed. The safety precautions used in handling beryllium in the laboratory are also described.

Jan 1, 1962

By George A. Morgan

The 53 countries that constituted Africa in 1990 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, the titanium minerals-ilmenite and rutile, vanadium, vermiculite, uranium, and zircon. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States. Despite the underdevelopment of much of Africa, mineral raw materials playa very important part in the national economies of many of its countries. In many cases, the production of minerals is the dominant economic activity in the country, often having the largest and most sophisticated work force. In several countries, one or two mineral commodities are dominant in a weakly diversified economy. Among these are petroleum and diamonds in Angola, petroleum in the Congo, gold in Ghana, bauxite in Guinea, uranium in Niger, phosphate in Senegal and Togo, and copper and cobalt in Zaire and Zambia.

Jan 1, 1992

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By L. C. Brichta

The Canyon Diggings zinc-lead deposit is in an area of structural deformation of sedimentary rooks in Newton County, Mo., 14 miles southeast of Joplin, within the southern limits of the Tri-State district. Mining and milling on the several tracts covering the area had been carried on sporadically since 1900, and incomplete records show a production of 1,341 tonsof zinc and lead concentrates. On the northern part of the deposit the predominant metal is which occurs as galena, cerrusite, and pyromorphite in broken chert near the surface. On the southern part, lead is subordinate to zinc, which occurs mainly as carbonate and silicate minerals in brecciated chert to a maximum depth of about 150 feet. Analyses of samples from Bureau of Mines drilling indicate that approximately 77 percent of the zinc and 50 percent of trio lead i8 in nonsulfide minerals resulting from the oxidation of sphalerite and galena. Between August 12, 1948, and October 5, 1949, the Bureau of Mines investigated the deposit by churn drilling and sampling 85 holes aggregating 10,571 feet of bore and sampling two mill-tailings dumps and three mine dumps. Factual data on the investigation and the logs of Bureau of Mines drill holes are presented in this report.

Jan 1, 1950

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968